Search Documents

By James P. Morris, William H. Hansmire

The U. S. Department of Energy's (DOE) Yucca Mountain Project (YMP) is a scientific endeavor to determine the suitability of Yucca Mountain for the first long term, high level nuclear waste repository in the United States. The status of this long-term project from the construction perspective is described. A key element is construction of the Exploratory Studies Facility (ESF), which is being excavated with a 7.6 m (25 ft) diameter tunnel boring machine (TBM). Development of the ESF may include the excavation of over 15 km (9.3 mi) of tunnel varying in size from 3 to 7.6 m (10 to 25 ft). Prior to construction, extensive constructibility reviews were an interactive part of the final design. The intent was to establish a constructible design that met the long-term stability requirements for radiological safety of a future repository while maintaining flexibility for the scientific investigations and acceptable tunneling productivity.

Jan 1, 1995

By S. -H. Kim

This work investigated the effect of the concentration of CO2 and lead contamination on the forest ecosystem. Changes of the plant growth, lead concentration in soil, plant, and soil microbial community caused by CO2 concentration (380 ppm and 760 ppm) and lead contamination (500 mg/kg) were measured. Plant growth was inhibited by 50% due to lead contamination. Particularly, shoot growth was inhibited more than the root. However, the root elongation was not affected by the CO2 concentration increase. The diversity of microbial population with AWCD (Average Well Color Development) and PCA (Principle Component Analysis) showed that the lead contamination has an effect com-pared to CO2 concentration. The Shannon index calculated from DGGE profiles was high in soil with Pinus densiflora, while the effect of CO2 concentration was not significant (P<0.5). The similarity of microbial community from each treatment showed that lead has an effect on plant growth and microbial community rather than the CO2 concentration.

Jan 1, 2006

By R. P. King

Knowledge of the behaviour of flotation machines had developed and increased considerably over the last few years. Although much work remains to be done on the study of the fundamental processes that influence the collection of hydrophobic particles at an air-water interface, there is enough information to permit the building of realistic models of the gross flotation behaviour of various ores. These models serve as an ideal base for the development of simulation techniques for the steady-state behaviour of entire flotation plants that consist of a large number of individual flotation machines. Simulation techniques have a very real role to play in assisting with the design of new plants and in improving the operation of exisiting plants. Recently, highly efficient data-logging systems have been introduced on flotation plants. These systems are based on the on-line measurement of volumetric flowrate, pulp densities, and metal contents, and they generate enormous quantities of information regarding the operation of the plant. Unfortunately, this information is largely wasted at the present time because efficient data-reduction techniques, although available10 are not in common use. Simulation techniques play a central role in such data reduction because they form the essential link between the fundamental kinetic flotation processes on the one hand and the plant data on the other.

Jan 1, 1974

By D. W. Scott, D. G. Minnes

Introduction Ontario&apos;s diverse industrial mineral resource base includes structural minerals such as sand and gravel, crushed stone, building stone, clay, shale, limestone, and dolostone. These resources are used to produce aggregates, brick, metallurgical stone, fillers, cement, lime, and other construction materials. The majority of the operations are in deposits of Palezoic and Quaternary age in southern Ontario, close to the major markets. Province-wide, there were more than 140 Mt (154 million st) of aggregates produced in 1985. About 115 Mt (128 million st) of that was produced in southern Ontario with the rest being largely from Crown land in northern Ontario. Structural industrial minerals account for more than 80% of the value of total industrial mineral production. The remaining 20% is accounted for by the nonstructural minerals, such as salt, which is produced in the southwestern part of the province. A host of other nonstructural industrial minerals are known. Production, though, is currently restricted to calcite, gypsum, quartz, talc, nepheline syenite, and byproduct metallurgical sulfur products (Fig. 1). Major production is close to the large markets of urbanized southern Ontario and the northeastern and northcentral US. With an abundant variety of industrial mineral resources and the large population within 650 km (400 miles) of most deposits, the market offers great potential. Ontario&apos;s nine million people accounted for about 35% of Canada&apos;s entire $476.3 billion gross domestic product in 1985. This equates to about one-third of the nation&apos;s buying power being within a 200-km (125-mile) radius of Toronto. This major concentration of industrial and economic activity has resulted in a well-developed industrial minerals industry that fulfills most of the structural industrial minerals demand in Ontario. Nonstructural industrial minerals are similarly well placed to compete in this high demand area. Although Ontario manufacturers still import some of these materials, Ontario products are achieving significant market share. And, they serve the needs of neighboring provinces and states. Present production and trends Ontario has traditionally produced significant amounts of industrial minerals. This produc¬tion had a value of $956 million in 1984 (Table 1). Structural materials production in 1985 and 1986 approached or exceeded levels not seen since the early 1970s. Many new products have been developed using these raw materials. The industry is becoming concentrated in the hands of several large companies, mainly four large cement com-

Jan 12, 1987

By H. B. Trinh, R. R. Srivastava

"Spent auto-catalyst is a potential secondary resource because of the higher concentration of valuable platinum group metals (PGMs) as compared to the primary ores. Despite the well-developed commercially tenable technologies, further researches are being carried out to extract the PGMs with high efficiency. It is however, critical in this context to reuse not only the PGMs but also other metals contained in the spent auto-catalyst particularly that of the cordierite substrate such as aluminum, magnesium and cerium oxide (CeO2). This is important in view of the fact that no recycling process has ever stressed upon the recovery of cordierite substrate and CeO2 since the main target metals are mostly the PGMs. In this study, a new hydrometallurgical approach has been proposed in order to recover the PGMs as well as cerium oxide and materials from the cordierite substrate by using sodium hydroxide roasting followed by sulfuric acid dissolution. Under the optimal conditions for roasting at above 600°C, and weight ratio of sample to NaOH of 1:1 for 60 min, the cordierite was converted to the soluble phases. Dissolution of the roasting products using H2SO4 solution (1M) at 25°C for 60 min enriched the PGMs and Cerium oxide contents in the residue. Subsequently, PGMs in solution after dissolution can be cemented using Al and Cerium oxide in residue can be recovered by hot digestion using concentrated H2SO4.. INTRODUCTION Auto-catalyst can significantly control the gaseous emission of automobiles, and has been considered as a potential secondary source of Platinum group metals (PGMs) after being decommissioned from the vehicles. The PGMs demand is continuously increasing to comply with the growing vehicle population and the tightening of emission standards all over the world; meanwhile the natural resources of these metals is facing the threat of depletion. Therefore, it is crucial to progressively substitute with an alternate resource to supply PGMs other than that of the primary ores. Nowadays, vehicular transportations worldwide are totally installed with the auto-catalysts. However, they should be replaced after reaching their service life. If there is no recycling of such resources, huge amount of valuable metals will be wasted. The quantity of PGMs that can be recovered from the spent auto-catalyst depends on the size of car, which averages to 1-2 grams for small cars and 12-15 grams for the big truck; this is significantly higher than that of the primary ores containing 2-10 grams PGMs per ton. Consequently, the recovery of PGMs from spent auto-catalyst becomes extremely favorable as compared to the primary resources due to higher concentration of PGMs, with much lower and simpler processing steps, and lesser pollution."

Jan 1, 2018

By J. J. Poveromo

"Iron ore for alternate iron processes concerns alternate iron products designed for use in EAF (electric arc furnace) steelmaking processes. These alternate iron products include both DRI (direct reduced iron), HBI (hot briquetted iron) and merchant pig iron. Merchant pig iron can be produced in conventional blast furnaces, mini blast furnaces (including charcoal BF's) or novel processes such as RHF/SAF (rotary hearth furnace/submerged arc furnace) such as Iron Dynamics or RHF such as Mesabi Nugget. These novel processes are coal based and can use iron ore concentrates or recycled steel plant oxides. The blast furnace processes can use conventional feed materials: pellets, sinter, lump ore and coke. However, DRI and HBI processes are predominantly pellet based but require DR grade pellets that are low enough in acidic gangue (SiO2 and Al2O3) to avoid additional expense in the EAF process This paper will focus on the quality and availability of DR grade pellets for NAFTA DRI/HBI plants but also concentrates for fines based processes and feed materials for merchant pig iron production. INTRODUCTION This paper will outline alternative (to the blast furnace) competitive ironmaking processes and process routes. Within each section the types of iron ore to be utilized will be discussed. Before discussing some of the details of these processes, it may be appropriate to review some definitions and commonly used terms within this industry. DefinitionsDirect Reduction: Reduce iron oxide to metallic iron without melting. Unreduced ore compounds remain as undesirable oxides • Direct Reduced Iron: Iron oxide feedstock exits in same form as entered (pellets in, pellets out; lumps in, lumps out) • Hot Briquetted Iron: DRI that has been hot (1200°F, 650°C) briquetted to a high density pillow shaped briquette • Hot Metal: Molten iron in liquid form, above 2500°F, 1370°C • Pig Iron: Solid product of the iron blast furnace • Residuals: Undesirable elements such as copper, nickel, chromium, tin, sulfur, molybdenum and phosphorus • Gangue: Rock minerals in the iron ore such as silica (SiO2), alumina (A2O3), calcia (CaO), magnesia (MgO). These remain in the oxide form in DR processes. • Reduction: Fe2O3 + 3 CO = 2 Fe + 3CO2 2 Fe2O3 + 3 H2 = 2 Fe + 3H2O (Fe2O3 > Fe3O4 > FeO > Fe)"

Jan 1, 2018

By E. S. Peterson, M. K. Harrup, K. A. Dolbeare, J. E. Wey

Efficient methods for removal of copper from heap leach solutions without mobile organic phases are a current mining industry need. To satisfy this need a selective, high-capacity, durable solid material is required. The INEEL has developed a set of materials based upon current solvent extraction chelates that provide selective copper concentration in the presence of high concentrations of iron. In contrast to conventional solvent extractions, our strategy anchors the chelators to a non-polymeric solid substrate through the use of a custom designed linker molecule. The fundamental synthetic routes to these materials have already been established and attachment to the solid surfaces achieved in an efficient manner. Our continuing research is focused on the optimization of the synthetic pathways to these solid materials and the evaluation of their copper capturing capabilities.

Jan 1, 2002

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By Ray H. Hario

Background of Erie Mining Company Erie Mining Company, managed by Pickands Mather & Co., is one of the largest producers of iron ore pellets in the United States. The plant is located at Hoyt Lakes, Minnesota, sixty-five miles north of Duluth on the eastern end of the Mesabi Range. Taconite Harbor, situated on the north shore of Lake Superior, is the location of its Power Plant and shipping facilities. (Figure 1) Even though the plant commenced operation in September, 1957, its true be-ginning can be traced back to 1931 when Pickands Mather, in conjunction with Bethlehem Steel Corporation and Youngstown Sheet and Tube Company, began investi-gating the possibilities of processing low grade ores. In 1940, Erie Mining , Company was formed. During the early and middle 1940&apos;s, laboratory and pilot plant research was proven to a point where a preliminary plant was deemed feasible and built in 1948. This plant had an annual capacity of 203,200 t (200,000 long tons) per year and, until mid-1952, was the only taconite plant in existence using commercial-size equipment. During this period, ownership of Erie Mining Company was expanded to include Interlake, Inc. and The Steel Company of Canada, Limited. In 1953, authorization was obtained from the owners to build a 7.62 M t (7.5 M long tons) per year plant at a cost in excess of $300,000,000.

Jan 1, 1977

By Masaji Kato, Yuusaku Tominaga

To maintain good condition of ventilation for both safety and economy, many regulators are installed in a network. In case the open state of a regulator is different from the set point, identification of a broken regulator and a countermeasure to recover airflow distribution in a network must be initiated as soon as possible. An experienced mining engineer can sense a deviation from ordinary airflow quantity. In this paper, a new system to monitor all the regulators in a network is introduced. The basic concept of the system is utilization of both human sensing of airflow rate and computer simulation to understand the macroscopic characteristics of a ventilation network. A fuzzy pattern distinction method is used to process human determination of airflow rate that may be ambiguous. The applicability of the system is demonstrated using the ventilation network of the Horonai coal mine, Japan. In particular, it is shown that the system can identify the regulator to be repaired from information supplied by workers relating to air- flow in a few sensor branches.

Jan 1, 1997

By D. Murray

"The Mine Improvement and New Emergency Response (MINER) Act included the need for improved chemical technologies to address respiratory protective device inadequacies and refuge alternative development. The National Institute for Occupational Safety and Health’s (NIOSH) National Personal Protective Technology Laboratory (NPPTL) invests in research and development to improve the carbon dioxide (CO2) scrubbing technologies built into these mine safety systems. Testing at NIOSH NPPTL is performed using a custom-designed test system containing a chemical reactor and sensors in a constant flow of simulated expired breath to evaluate chemical performance for the scrubber materials. Current testing procedures focus on device duration or capacity, but do not report criteria needed to effectively optimize chemical performance. In this presentation, testing results which identify the chemical performance roles for CO2 scrubber components will be reported, and specific component chemical activities will be linked to both duration and CO2 absorption capacities. Chemical components being evaluated include hydroxyl, superoxides, metal, and amine active sites, distributed in salts, zeolites, metal-organic frameworks, and microporous materials. INTRODUCTION CO2 absorbents and oxygen sources are at the heart of closed circuit breathing air supply systems used in mining escape and rescue operations. CO2 absorbent technology was first developed for diving rebreathers and has been in use for over a century. Typically these devices include a soda lime formulation of pellets in the 8-12 mesh range. Larger 4-8 mesh particles are used in medical grade “low-flow” applications, since these particles present a lower flow resistance regime more amenable for use with resting individuals. Potassium superoxide and lithium hydroxide formulations are also used, where in each case the formulations involve bulk solid pellets or materials affixed to surfaces. CO2 capture technologies are now under intensive study in the energy and automotive industries, where the pursuit of optimal combustion processes has led to the development of new materials to capture, convert and store CO2, oxygen and carbon monoxide gases. Recent advances in nano-structured and high surface area catalysis have produced novel materials demonstrating chemical performance improvements in these industries, and these improvements may now also be adapted to enhance chemical efficiency and performance in escape and rescue devices. Higher surface area materials offer promise for improving the efficiency, or decreasing the burdens associated with the use of closed circuit respiratory protective devices containing CO2 absorbents. Novel chemicals that display advantages in chemical performance or decreased burden will be examined for inclusion in developing systems such as the next-generation closed-circuit mining escape respirator or refuge alternatives."

Jan 1, 2018

By G. Meiers, M. O’Kane

Dry cover systems as a closure option for management and decommissioning of waste rock and tailings is a common prevention and control technique used at numerous sites around the world. Numerous site-specific factors control the long-term performance of dry cover systems. Site-specific climate conditions are one of the key factors to consider when determining the objectives of a dry cover system because these conditions will significantly influence long-term performance. There are advantages and disadvantages of characterizing the site on an annual basis as generally a “dry” site (annual potential evaporation greatly exceeds annual precipitation), or generally a “wet” site (annual precipitation meets or exceeds annual potential evaporation). The field performance monitoring data and discussion presented herein illustrates the caution that is required when using these “annual” criteria for characterizing site climate conditions. Numerous sites exist where precipitation exceeds potential evaporation on an annual basis; however, the site typically experiences hot, dry summer months where evaporation greatly exceeds rainfall. These dry summer conditions have a strong influence on long-term performance. In contrast, sites where potential evaporation exceeds precipitation on annual basis, typically experience periods of the year when a moisture surplus occurs, which also impacts on long-term performance. This paper uses soil-atmosphere cover design modelling and field performance monitoring from sites in Canada, Australia, and the United States to demonstrate the importance of considering site-specific climate conditions when predicting long-term cover system performance.

Jan 1, 2003

By D. G. Mirakovski, B. Krstev

The paper presents models of auxiliary ventilation systems with leaky ducts and algorithms for calculations of pressure loss, air leakage, and volume flow ratio and pressure fans. Two basic models are discussed: 1st model for a duct with leakage through the flange joints; 2nd model for a duct with an equivalent longitudinal aperture. The present analytical system has been successfully applied to developing of computer software named DAVentS. A. sample problem is used to illustrate efficiency and accuracy of DAVents software in solving most common problems in process of designing AVS.

Jan 1, 2002

By W. J. Nelson

Detailed underground geologic map- ping at a scale of 1:1200 has been carried out at the Crown II Mine of Freeman United Coal Mining Company, which operates in the Herrin (No. 6) Coal Member. The roof sequence, upward from the coal, includes (1) soft, medium- to dark-gray shale; (2) hard, black, fissile shale; (3) argillaceous nodular-bedded limestone, and (4) fine-grained, shaly, water-bearing sandstone. The first unit is highly lenticular, and any or all may be missing at a given locality. The sand- stone has a sheet facies and a channel facies. The Herrin Coal is eroded in channels near the Crown II Mine. Structural features mapped at Crown II include normal and strike-slip faults of small displacement, "slips" and clay dikes, and limestone "bosses." Less stable roof and wet con- ditions are encountered where the limestone is thin or missing or where it is broken by natural fractures or by artificial openings that inter- sect the water-bearing strata above the limestone. Geologic mapping of the underground workings has allowed us to predict faults, fracture zones, and channels ahead of the face for this mine. Some lithologic and structural patterns apparently are random and cannot now be projected. Conventional exploratory drilling is entirely inadequate to map faults or lithology of the roof, but it does indicate the range of lithologic variability, which can be used to project needs for roof sup- ports. Drilling also is useful In locating channels and in mapping regional variation in thickness and facies of the sandstone.

Jan 1, 1980

High pressure grinding rolls have found widespread acceptance for cement processing, and are now making their debut in the metalliferous minerals industry. Significant energy and wear material savings appear achievable in many applications. This paper re- views the technical literature on this important, emerging technology.

Jan 1, 1997

By Dr. Jagdish C. Agarwal

Kennecott Copper Corporation has developed a new hydrometallurgical process for extracting nickel, copper, cobalt and molybdenum from maganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45 C to 50 C and has been successfully demonstrated in a continuous pilot plant processing 800 lbs of nodule ore per day. The chemistry, basic flow sheet and operating characteristics are presented and discussed.

Jan 1, 1978

By D. K. Dysinger

The U.S. Bureau of Mines investigated leaching of chalcopyrite with sulfuric acid-oxygen under conditions anticipated during in situ leaching. A central composite experimental design was chosen to study oxygen pressures of 150, 300, and 450 psi, leach temperatures of 35?, 65°, and 95° C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0, and 1.5, leach times of 8, 16, and 24 hours, initial acid strengths of 0.6, 1.2, and 1.8 g H2SO4/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. The leaching kinetics were consistent with the shrinking core model. A quadratic response surface model was used to determine linear and interaction effects of the design factors on rate constants from Arrhenius correlations.

Jan 1, 1993

By B. Bergmark, O. Guyot, A. Broussaud, C. Bouché

The Boliden Aitik concentrator in Sweden processes 2,000 t/h (2,200 stph) of low-grade copper ore. The plant consists of five grinding lines that feed four bulk-flotation banks with a scavenger-concentrate regrind mill und a column cleaner circuit with a regrind mill. The authors installed a model-based expert optimizing control system to maximize copper recovery in the bulk-flotation circuit while maintaining an appropriate copper grude in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent- addition rates. It combines the power of a dynamic population-balance model that estimates mineral liberation in each stream, an optimizer that computes appropriate set points and a rule-based module that implements the strategy. The benefits have been evaluated over a period of three months. The model-based expert optimizing control system generates a measurable increase in copper recovery, around 0.5%, and an optimized bulk-concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 2000

By Tom L. Enos

Increased production through the plant was limited due to thickener circuit constraints. To overcome these constraints and maximize plant throughput to match grinding circuit capability, two options were considered: A. Adding 2000 TPD CIL circuit to operate in parallel with the existing CCD circuit. B. Adding a CIL circuit to treat the entire 4600 TPD while retaining some thickeners for tailings thickening. Option B was selected based on simplified plant operations, reduced operating costs, minimal capital requirements, reduced solution losses, and bullion grade improvement.

Jan 1, 1989

By Earl L. Rau

Although the Sagasca deposit has been known for 76 years, the property was never put into successful operation because of various adverse factors including low market price for copper, legal entanglements, unsuccessful financial arrangements, and an inadequate metallurgical process. Late in 1963, Continental Copper & Steel Industries, Inc., obtained legal control of this property. Since that time there has been a concentrated effort to complete the necessary mine appraisal, process development, and engineering design, and to solve the legal and financial problems to bring this property into production.

Jan 1, 1970