Search Documents

By John R. Keith

Keith, John R. 1968. Relationships of lead and zinc contents of trees and soils, Upper Mississippi Valley District. Preprint, Fall 1968 Meeting, Soc. Mining Engineers of AIME. Lead and zinc contents of elm, maple, and oak trees and of soils in which the trees grew were determined in samples from the Upper Mississippi Valley mining district, and from an area outside but contiguous to the district. The lead and zinc analyses of plant materials served to differentiate the mineralized and non-mineralized areas. Stems contained about two times as much lead and about 2-5 times as much zinc as did leaves taken from the same stems. Lead and zinc analyses of all soil horizons could be used to differentiate between the two areas. Soils at most sample sites in the mineralized district seemed to be more reliable than plants for geochemical prospecting and are a more practical sampling medium. Soil samples from areas with thick loess cover, however, failed to indicate the presence of mineralized bodies whereas tree samples from the same sites contained anomalous amounts of lead and zinc. It is suggested that in areas of thick loess cover plant samples could be used in prospecting for lead and zinc.

Jan 1, 1968

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

By O. A. Bascur

Current competitive demands on the process industries stimulate the need for improved operating efficiencies and compliance to stricter governmental regulations. Emerging information technologies allow narrowing the gap between management business objectives and the process control level. Benefits come from enhanced energy management, operating costs reduction, enhanced scheduling of activities, reduced quality giveaway, enhanced market driven production and enhanced decision making. Plant management systems integrate economic performance monitoring by controlling the business rather than just throughput and product quality. Sound business based decisions about how to operate the plant can be achieved by adequate dynamic performance monitoring at the plant level and the enforcement of the desired targets at the process control level. This paper describes some of the key requirements to implement a process management system to meet stricter process performance standards. Extensions are made to facilitate conforming with regulations established by various governmental and industry monitoring agencies.

Jan 1, 1993

By Y. Luo, S. S. Peng

Several issues deserve further attention to improve subsidence prediction accuracy. These include: subsidence initiation and development over a setup entry area; subsidence development after face stop; and subsidence over chain pillar. An intensive subsidence monitoring program has been carried out over several longwall panels. A large amount of subsidence data has been collected, analyzed and solution techniques developed. In this paper, some of the measured data. data analysis techniques and the developed prediction methods are presented.

Jan 1, 1992

Drainage and erosion control often become problems at mine reclamation projects. An example of this was an abandoned surface uranium mine on the south Texas plains. Engineers with the Texas Railroad Commission solved these and other problems with a three-dimensional geomatrix erosion-control matting at the 69-hm2 (170-acre) site, about 70 km (45 miles) southeast of San Antonio. Enkamat, manufactured by Akzo Nobel Geosynthetics, was installed to reinforce the grass waterways that handle runoff from the reclaimed mine. Reclamation was completed in the spring of 1992. Bill Walker is regional manager for Erosion Control Systems. He worked with the contractor to identify an erosion control product that complied with the project's design and installation parameters. "Use of erosion control matting enabled us to reduce erosion control costs," said Mark Rhodes, with the Texas Railroad Commission. "Also, the erosion control material was more aesthetically compatible with the reclaimed landscape." The commission's design called for a terrace ditch to be constructed midway up the reclaimed spoil slope to catch and collect water. Commission engineers selected spoil slopes, ranging from 5% to 8%, to build reinforced grassed waterways to drain the collected water from the terrace ditches. This was done instead of dropping the water at steeper slope location in rip rap- or concrete-lined channels. Enkamat's three-dimensional geomatrix of heavy nylon monofilaments is 95% open space that aids root growth. Its root-reinforcement system resists the hydraulic lift-and-shear forces created by high-volume discharges of water. In addition, fine eddy turbulences are prevented from isolating and uprooting individual roots and clumps of vegetation. Enkamat is flexible and lightweight. This makes it easy to install. And, because grass grows into it over time, it "disappears" after installation. Between 12,540 and 14,200 m2 (15,000 and 17,000 sq yds) were installed in the waterway using 150-mm (6-in.) staples to fasten the matting, said contractor Dale Blackstock. "It was easy to use; no problem at all to put down." Blackstock selected Enkamat from a list of eight different channel lining materials described as acceptable in the commission's design specifications. The design specifications were based on the results of channel-lining performance tests conducted by the Texas Department of Transportation. Rhodes said that the commission's Abandoned Mine Land Reclamation program had installed Enkamat on other abandoned uranium mines and on an abandoned surface lignite mine near Austin. "Pretty much all of our installations of Enkamat have worked out well," he said. "There have been no failures. The reinforced grass waterways have performed as designed."

Jan 1, 1998

Longwall mining is a commonly used method of coal extraction that involves the complete removal of large, rectangular panels of coal. Longwall mining causes the immediate seam roof to break and fall into the void created by mining. The convergence of the surrounding strata towards the mining void causes subsidence on the surface. The subsidence magnitude is related not only to the mining depth, the topography, the geological features and the overburden materials, but also to the sequence of the strata overlying a coal seam. In additional to the vertical subsidence which is evident at the surface, there are also horizontal movements inwards toward the centre of the void, which cause the surface to tilt, bend, stretch and com-press. This paper presents a parametric investigation of the influence of the overburden stratigraphy to surface deformations due to longwall mining using 2D finite element models. Models simulate rock movement by applying equivalent edge load to the open roof.

Jan 1, 2008

By R. A. Williams

Surface and electrochemical techniques have been used to describe the surface chemistry of ferrosilicon powders, as a function of pH and electrochemical potential, for conditions typical of operating DHS plants. The practical consequences on the likely corrosion behaviour and associated electro- kinetic particle-particle interactions (which affect stability to sedimentation) in the suspension, are discussed.

Jan 1, 1987

By Matthew Price, Laura Brown, Atulya Verma, Samantha Espley

Burst-prone conditions are a significant hazard in deep hardrock mines, elevating the risk to excavation stability and, more importantly, to worker safety. As mining progresses deeper, induced stress changes may trigger the initiation of rock failure processes which can be detected and recorded as mine seismicity. The implementation of seismic monitoring and routine seismic data analyses enables mine seismicity to be quantified spatially, temporally and on scale. The ability to quantify and characterize mine seismicity offers the opportunity to gauge seismic hazard, identifying high risk zones for mitigation against burst-prone excavation failure. Over the last decade, the Mines Technical Services (MTS) group at Vale Canada Limited’s Garson Mine assessed seismic hazard with the objective of assigning practical mitigating controls to zones identified as having a high rockburst potential. Initially, seismic hazard was computed using the Seismic Excavation Hazard Mapping (SEHM) software developed by the Mining Innovation Rehabilitation and Applied Research Corporation (MIRARCO) at Laurentian University, Canada. More recently, Vale Sudbury Operations partnered with the Australian Centre for Geomechanics and the University of Western Australia’s mXrap consortium. Through the consortium partnership, MTS at Garson Mine implemented the mXrap seismic data analyses platform, including the grid-based seismic hazard assessment tool. Building on 10 years of seismic hazard assessment experience at Vale Garson Mine, this paper summarizes a comprehensive case study, comparing the two tools (SHEM and mXrap) used at Garson Mine to assess, quantify, and represent seismic hazard. Subsequently, results of the Garson Mine comparative seismic hazard study will be discussed, emphasizing the need for an all-inclusive hazard assessment tool, focused on delivering practical mitigating controls that further enhance the overall safety of seismically active underground mines.

Apr 26, 2022

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

By W. R. Junge

The investigation, selection, and implementation of remedial activities for large, complex mining and milling sites is dependent on the cost-effective management of tailing and waste materials. Site investigations evaluate the contaminant source areas, assess the potential release rate of contaminants, and determine the acceptable contaminant release rate for the site. Selection of appropriate remedial activities is based on evaluation of constructability, reliability, performance, effectiveness, permanence and cost. Remedial technologies available for tailing and waste material include removal, consolidation, capping and drainage control. Proper implementation and documentation of the selected remedial activities are critical to the overall success or failure of the remedial program. A step-by-step process, established at the initiation of a project, should accurately document all construction activities, monitor environmental conditions at the site, assess the performance of the remedial activities, and, ultimately certify that the remedial activities have met relevant and appropriate standards. Case histories are presented for a uranium mill at Uravan, Colorado and a lead, zinc mine at Gilman, Colorado. These case histories provide examples as to the combination of remedial technologies that have been applied at these specific sites.

Jan 1, 1989

By Thomas D. Henderson, Wayne R. Hopkins, Arthur Lynch

Brought on stream in 1975, the 10,000-tpd copper oxide processing plant of Anamax Mining Co. at Twin Buttes, Ariz., is now at design capacity. Based on acid agitation leaching, solvent ion exchange, and electrowinning, the Anamax plant bridges an ore to metal gap by producing mine site copper cathodes from lime-bearing oxidized feed. Until recently, such material was considered submarginal because copper recovery was uneconomic using conventional methods. The new Twin Buttes oxide plant, the largest of its kind in North America, is one stage in the expansion of Anamax, a joint venture owned equally by The Anaconda Co. and Amax Inc. Other phases include an accelerated stripping program in the pit, an expansion of the sulfide concentrator from 32,000 to 40,000 tpd, and construction of a 57 MW diesel generating station for the oxide plant. Once the basic oxide flowsheet had been selected, Anamax awarded a contract to a joint venture of Arthur G. McKee and Co.' (Western Knapp Engineering Div.) and Davy Powergas' (a member of the Davy International group). The contract covered process design, engi¬neering, procurement, and construction. The property, identified by Banner Mining Co. in the 1950s and developed by Anaconda, was put into production in 1965 as an open pit mine equipped with a 32,000-tpd sulfide flotation concentrator. The Twin Buttes mine has since become one of the largest earth¬moving operations in the world, excavating some 10 tons of waste per ton of ore. At the original sulfide mill feed rate, the mining fleet moved 375,000 tpd of material (225,000 tpd alluvium and 150,000 tpd of rock). The most significant copper mineral in the ore body is chalcopyrite, which is scattered in pockets of weak mineralization. Cap oxidation has progressed to depths of several hundred feet, principally as chryso¬colla. Present estimates place minable reserves at 347 million tons of sulfide ore grading 0.6% copper and 55 million tons of oxide ore grading 0.9% recoverable copper from 1.25% total copper. The nonre¬coverable fraction is composed of native copper and insoluble copper oxides and sulfides. The oxide ore has been partially stripped, and 25 million tons having a copper content greater than 0.6% have been stockpiled. The stripping of oxide ore to expose sulfides will continue for several years. The copper oxide studies launched by Banner Mining in the 1950s were continued by Anaconda. Process routes investigated included: acid leaching; cyanide leaching; segregation roasting; chlorination, oxidation, and reduction; flotation in combination with leaching; cal¬cite flotation plus leaching; copper oxide flotation; and sulfidization flotation. By late 1968 test work favored a low temperature roast followed by an ammonia-ammonium carbonate leach of the ore. During this period, acid leaching had been discounted because of excessive con¬sumption of expensive acid by the high limestone ore matrix. Restric¬tive SO2 emission controls in 1971 suggested an increase in acid production and availability at a lower cost. Research then switched to acid leaching, resulting in development of the present flowsheet. Mechanically agitated leaching in a cascaded series of tanks was selected in preference to vat leaching after piloting a stirred-tank system. Preliminary testing of vat leaching indicated that inter-vat solution clarification problems could be caused by gas evolution from leaching of high limestone ore. Lack of research time for resolution of this problem, plus success of the pilot agitation system, dictated the final flowsheet selection. In 1973 Anamax decided to proceed with agitation acid leaching to produce liquor for a solvent ion exchange (SIX) and electrowinning (EW) installation. At that time, such systems were proving their eco¬nomic viability, and they allowed direct recovery of high quality cath odes while bypassing the smelting and refining of lower grade cement copper precipitates. The Anamax oxide plant processes a grade of about 1% recovera¬ble copper from stockpiled sources and new mine production. Unit operations include size reduction, agitation leaching, countercurrent decantation washing of residue, pH adjustment of solution, clarifica¬tion, solvent ion exchange, and electrowinning of copper, with a mini¬mum of environmental impact. The feed to the primary crushers is composed of: 1) -10-in. stockpiled oxide ore, which has passed through the mine crusher and has been grade-segregated to allow blending for a consistent feed material. 2) -4-ft ROM oxide ore stockpiled in the early mining operation. 3) -10-in. ore currently being mined. Ore is delivered in 100-ton mine trucks to a dump pocket, where an apron feeder transfers the ore to an inclined 6-in. fixed grizzly. The grizzly oversize passes through a 48 x 60-in. primary jaw crusher, where it is reduced to -6 in. The fixed grizzly undersize and the crusher product are conveyed to a 4-in. vibrating grizzly. Oversize from this grizzly reports to a 7-ft Standard cone crusher, where it is reduced to -1 in. The crusher product and the vibrating grizzly undersize are conveyed to two 8 x 20-ft double-deck vibrating screens that operate in closed circuit with two 7-ft short head cone crushers. Screen undersize (-1/2 in.) is delivered to a covered conical fine ore stockpile with a designed live capacity of 15,000 st. Beneath the stockpile are ten Pioche belt feeders feeding two conveyor belts that supply the milling circuits. Each group of five feeders has two variable speed and three fixed speed drives. Grinding to 95% -48 mesh is done in two parallel lines, each consisting of an 111/1 x 18S -ft rod mill and a 12' x 30-ft ball mill in open circuit. Water is added to maintain a pulp density of 72% solids in the mills. Further water additions are made to the ball mill discharge sumps to create a 60% solids slurry for transfer to the leaching reactors. The nominal grinding rate is 440 tph solids. A splitter box on the product from the mills separates the incoming slurry into two streams, one for the leaching reactors and the other for the pH adjustment reactors. This split is determined by the lime content of the feed material and the pH of solution entering the pH adjustment reactors. Five 30-ft diam by 31-ft high mechanically agitated, rubber-lined leach tanks are arranged in cascade, with gravity transfer from one to another by enclosed launders. Concentrated sulfuric acid (93.2%) from storage is added to the pulp principally at the first leach tank, and the reacted slurry leaving the cascade after a 5-hr residence time at 50% solids is pumped to countercurrent decantation (CCD) wash thickeners.' At this point, most of the soluble copper has been leached from the ore. Up to 250 lb of sulfuric acid is consumed per ton of ore, the acid being supplied in tank cars from a nearby smelter. Leached slurry at 50% solids is washed countercurrently with return raffinate from the SIX plant in a series of four Doff-Oliver center caisson, 400-ft diam thickeners. Solids advance from thickeners No. I through No. 4 to the tailings dam. SIX raffinate advances from thickener No. 4 to thickener No. l, where a pregnant solution overflows to pH adjustment. To optimize solvent extraction, the pH of the pregnant solution from CCD thickener No. I is adjusted from 1.5 to 2.5 by adding unreacted ground slurry (split from the grinding circuit) to the preg¬nant overflow of No. I CCD thickener. The resulting slurry is retained for 45 min in three mechanically agitated leach tanks. CO, generated during leach and pH adjustment is ducted to a demister, where entrained acid droplets are removed. The cleaned CO, and the No. 4 CCD underflow are the only effluents from the plant. The underflow of No. 4 thickener mixes with tailings from the sulfide concentrator and is neutralized. Slurry exits the pH adjustment vessels at about 10% solids and

Jan 1, 1985

By M. T. Ityokumbul

The effect of reaction conditions on the desulphurization of oil sand coke residues has been studied. The variables investigated were temperature, reaction time, heat transfer resistance, and mode of caustic soda addition. The results obtained show that oil sand coke desulphurization increases with temperature, reaction time, and heat transfer rate. In an oxidative environment, coke combustion during molten caustic leaching (MCL) commences at temperatures above 500°C. The mode of caustic addition has no effect on coke desulphurization.

Jan 1, 1995

By M. Rîsteiu

The authors aim to analyze the behavior of smart sensors using Transmission Control Protocol/Internet Protocol (TCP/IP) infrastructure in hazardous applications, because of their advantages regarding safety, expansion and Quality of Service (QoS). Initially, some constraints are discussed for these applications. Then, the possibility is analyzed of using 2.4 GHz TCP/IP based transmission for sending data out of an industrial area. In this setup the authors evaluated the round-trip implementation (which requires a database of packet lengths), related to the delay introduced by the radio transmission algorithms from 802.15.4, and 802.11d/g protocols. Tuning results of different varying time-delays were compared to the constant delay cases from the literature (Deák, 2003; Lincoln, 2003). Both the hardware and software setups are implemented. Based on TinyOS specific software for hardware checking/ initiating communication/ starting/ closing measurements the authors have developed separate/combined procedures for testing the integrated devices. Measured time delay is presented and analyzed, for both beaconed and non-beaconed 802.15.4 transmission, with power optimization criteria. By testing two different implementations (Zhang et al., 2001), (ATmega256 RZAV - 256KB flash memory, the CC2420 IEEE 802.15.4 and ZigBee-compliant RF transceiver core - 128KB flash memory) the authors have found some time delay variations as a result of local processing by the ZigBee controller with an amount of flash memory. The work is also focused on adapting industrial measuring standard systems to the smart sensors, but not only through the 4-20 mA standard.

Jan 1, 2008

By J. G. Groppo, S. M. Khandrika, B. K. Parekh

It is shown that dewatering of fine coal particles (D50 = 21 µm) is enhanced near the point-of-zero-charge. The coal surface is modified by the addition of copper ions and by adjusting the pH to precipitate surface-active metal hydroxy species, which promote agglomeration and produce low-moisture cakes. Filtration kinetics data are used in calculating filter cake parameters from an integrated form of Darcy's law. The influence of copper ions and pH on filter cake parameters and the correlations among them are presented.

Jan 1, 1995

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

By Kenneth Denton, Michael Cutts, Andrew Bursey, Eric Eisold

Phase III of the Orme Street Combined Trunk Relief Sewer project connects two existing 2.13 m diameter combined sewers to a new 3.66 m diameter relief sewer at 7locations along a 970 m alignment in downtown Atlanta. The alignment was enveloped by adjacent structures and utilities. The project was constructed below the groundwater table through compressible residual soil, rock and mixed face using a myriad of construction techniques, including compressed air NATM and jet grouting. Numerous design and alignment changes and accommodations for existing utilities and conditions were made during construction. The authors believe this to be the ?rst NATM project in North America utilizing compressed air tunneling.

Jan 1, 2003

By Douglas G. Hubert

To put coal in its proper perspective as a source of energy for electric power production, we must first compare it to other energy sources. A report of the Atomic Industrial Forum dated February 1958 records a number of authoritative though widely varying predictions. The most optimistic of these states that by 1968 there will be a total U.S. capacity of about 6000 megawatts of nuclear power, if growth continues at the present rate. Other sources indicate over 200,000 megawatts of total electrical capacity in utility plants by 1968. This is only 3% nuclear. Therefore, 97% of our total power production will be from non-nuclear energy. Fig. 1 shows the distribution of energy sources of electric utility product- ion in the U.S. as reported by the Federal Power Commission in 1954. Note that less than one quarter of the total is hydro and about one half of the total is coal. For 1957, the Edison Electric Institute reports that of the total steam- electric generation in the U. S., 68.6% was by coal, 7.9% was by oil and 23.5% was by gas. This is an increase for coal and a decrease for oil and gas in those three years. Thus we can conclude that two-thirds of the steam-electric power in the U. S. is now generated by coal. Fig. 2 shows the major markets for coal for 1947 vs 1957. The greatest in- crease has been in the electric utility market, where it has more than doubled in the ten years. One-third of the total coal produced goes to the utilities which now represent coal?s major market. Utilities used 160 million tons of coal in 1957, and the estimated quantity for 1967 is 275 million tons, and for 1977 is 525 million tons. It is predicted that 85% of steam-electric power will be generated by coal in 1975.

Jan 1, 1959

By N. Weidner, V. A. Samaranayake, K. Awuah-Offei, S. Que

"This research sought to facilitate improved stakeholder (community) analysis using discrete choice theory (DCT). The work considered 16 project attributes and four demographic factors. The discrete choice experiment was conducted in Salt Lake City, Utah to illustrate the usefulness of DCT in mining stakeholder analysis. The data was used in discrete choice modeling of individual preferences. The approach answers three important questions for enhanced stakeholder analysis: (1) What are the factors that affect individual preferences? (2) What is the effect of demographics on individual preferences? (3) What is the value of environmental and social impacts to individuals in the community? INTRODUCTION Stakeholder analysis is crucial for effective stakeholder engagement because it is important to identify and characterize stakeholders in order to effectively engage in dialogue with them. This is not only true for all stakeholders but true for characterizing the members of a particular stakeholder. The local community is usually the largest and most diverse single stakeholder group. Also, the local community is perhaps the most important stakeholder group. Thus, analysis of the local community is essential for project management. Conventional mining stakeholder analysis is a three-step process, which involves evaluating: (1) each stakeholder’s view of the project (positive, neutral, or negative); (2) how influential each stakeholder is (high, medium, or low); and (3) how they will be impacted by the project (high, medium, or low) (ICMM, 2012). The results of this evaluation are documented in a stakeholder analysis matrix (Table 1), which is used to classify the stakeholders into three groups: highly influential supporter of the project, neutral about the project, and highly influential opponent of the project. This process can be used to describe groups of stakeholders (e.g. community, non-governmental organizations, etc.) or individuals making up a particular stakeholder group (e.g. members of the local community)."

Jan 1, 2016

By III Sadler

Processing bauxite and clay ores to reduce Iron content to levels low enough for the ores to be suitable raw materials for such products as refractories and abrasives has long been regarded as a diffi9ult problem. Standard magnetic separation processing of the untreated ore has been attempted by previous investigators with only limited success due to the finely divided state and weak magnetic susceptibility of the iron minerals (hematite, geothite, etc.) present in these ores. The new process described in this paper consists of calcining the finely crushed ore at 500 to 800 C and then reducing (with hydrogen, carbon monoxide, etc.) the iron oxides present to magnetite or elemental Iron. The magnetic susceptibility of iron in these forms is enhanced 40-to 100-fold over that of hematitie and is readily removed by simple magnetic separation. Starting with a 2.7% Fe20s Alabama bauxite ore, a 1.5% Fe20s product was produced in one pass through a Davis tube magnetic separator with 95 + % recovery of the iron-free bauxite fraction and a 20% Fe20a magnetic product. These findings suggest that with the addition of light calcination, reduction and magnetic separation steps to the conventional refractory grain production process, the large U.S. reserves of high-iron bauxites could be used.

Jan 1, 1990

By James S. Goff, Stephen J. Navin, Wesley W. Moulton

The White River Shale Oil Corporation (WRSOC) is developing a prototype oil shale facility on Federal Lease Tracts Ua and Ub located in northeastern Utah. This paper covers the successful driving of 1,525 m (5,000 ft) of dogleg downgrade decline with a 70-ton Paurat Roadheader mining machine and a conveyor muck-handling system. Ground support is with rock bolt and shotcrete; welded wire mesh is optional. The Upper Decline of 3.89 m by 8.69 m (12.75 ft by 28.5 ft) was mined through the Uinta Formation sandstones and shales in 210 days. The sandstones have a compressive strength in the 48 MPa (7,000 psi) range with a few bands of shale up to 137.8 MPa (20,000 psi). Green River Formation dolomitic marlstone with some sandstone lenses was mined in the Lower Decline 3.89 m by 5.64 m (12.75 ft by 18.5 ft) in 175 days. The Green River marlstones are tough massive formations ranging up to 206.8 MPa (30,000 psi). Roadheaders for use on steep slopes must be modified to accommodate the particular problems associated with mining downdip. The paper concentrates on the application of Roadheaders to steep slopes and the problems of mining tough materials such as marlstone. The paper also shows the advantage of using the method of excavation on long drives.

Jan 1, 1985