Search Documents

By M. S. Klima

This paper will detail the work that has been done in 1990 and 1991 at the Pittsburgh Energy Technology Center (PETC) on the development of the U.S. Department of Energy's (DOE) patented Micro-Mag Process. This process entails the use of a micronized-magnetite (minus-10 microns) and water mixture for cleaning fine coal (minus-600 microns) in a cyclone, along with the production and recovery of the magnetite. Emphasis will be on the results from micronized-magnetite recovery testing using both conventional wet-drum and high-gradient magnetic separators in which several key operating conditions were varied including feed percent solids, magnetite-to-coal ratio, magnetite grade, and feed rate. Also presented will be selected results from testing done on a 76-mm diameter cyclone at a relative density of 1.50 showing the effects of operating pressure, magnetite grade, and medium-to-coal ratio on separation efficiency. In addition, two methods for producing micronized magnetite, along with the corresponding size distributions, will also be discussed.

Jan 1, 1992

By L. Hagenbuch

Off-highway truck purchasers know the amount of tonnes, pounds, kilograms, etc, a truck will carry. However just because a truck is rated at 240 tons may in no way correlate to what that truck will actually carry. Two numbers define the carrying capacity of an off-highway truck: 1. The weight carrying capacity of the truck; 2. The volume carrying capacity of the truck. These two numbers must be in sync or the amount of payload carried will vary from the carrying capacity of the truck. Currently the Society of Automotive Engineers (SAE) standard J1363 January 1985 defines the volumetric carrying capacity of an off-highway truck. However as is well known in several South American countries, the SAE standard overrates the truck’s effective volumetric carrying capacity 15% to 20%. This paper presents a method for measuring “effective” body volumetric carrying capacity, resulting in a truck body for carrying the targeted load, matched to the loading equipment that interacts positively with the truck chassis.

Jan 1, 2002

By A. J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of steel wire ropes. Steel wire ropes are very suitable for mine hoisting due to their high strength and durability, but have the negative characteristic of a low strength/weight ratio. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength/weight ratio of synthetic ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application.

Feb 23, 2014

By A. D. Randolph

Comminution represents one of the major costs of mineral recovery from low-grade ores. Efficient mineral recovery in a typical low-grade ore grinding-flo¬tation process depends on grinding the ore small enough to liberate mineralization without producing excessive slimes, which would result in higher power and flotation reagent costs. Size criteria for efficient grinding should be stated in terms of the distribution of mineralization sizes, but as the mineralization-size distribution is difficult to determine, less desirable criteria of absolute particle-size distribution (PSD) are used in practice. Thus, there is considerable incentive to be able to analyze and predict the PSD performance of grinding circuits for control and optimization of the process. Any realistic model of a grinding circuit must account for recycle of oversize material; such oversize recycle adds to the total mill load and limits total production rate. Simulation of such closed-circuit operation to study grind factors affecting total throughput can be done in a straightforward fashion provided recycle calculations can be added to an accurate input-output model of PSD in the grinding mill itself. Such a total simulation of mill performance is of obvious practical value in assessing the practicality and benefits of various over-all mill control schemes and/or modes of operation. For example, considerable interest has been shown in the development of continuous on-line particle-size sensors and such instruments should be an operating reality in a few years. A total closed-circuit PSD model of this type would be invaluable in the utilization of, and in predicting the pay-out from, such an on-line particle-size sensor. The purpose of this paper is to present a new approach to the development of an input-output PSD model of a grinding mill. The model is continuous in the par¬ticle size coordinate, L, and is based on the principle of a particle population balance along the particle size coordinate. Most previous studies of the grinding unit operation attempt to relate power

Jan 1, 1971

By A. McCombs

Previous models describing the aggregation of polymer-coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called "active" sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1988

The impact of a methane explosion on mining operations cannot be over-emphasized. The explosion is a result of rapid combustion when a methane/air mixture is ignited by an unexpected energy release, such as a mine fire, electrical arc or sparks caused by frictions or rock falls. In most cases, an ignition of methane/air mixture could result in a deflagration other than detonation. Resulting flames and overpressure induced by a methane deflagration will harm neighboring miners and local ventilation control devices.. ,It is essential that the mechanism of an explosion and associated destructiveness be fully understood. This research seeks to predict an influence region of an incident happened within a representative underground mine geometry. The most common geometric changes in an underground coal mine are bends, regulators/doors, obstacle in airways and changes in sectional area. These geometric changes could result in an attenuation of the flame and pressure wave as a result of a methane deflagration. A study of this phenomenon could enable mine planners to have better understanding of the over-pressure redistribution due to the explosion. Both numerical and experimental work has been done in this study to ascertain a better insight of this potentially devastating event. The experimental data are also used to validate the turbulence and combustion models used in this test.

Feb 23, 2014

By M. A. Cristovici

The possibility of using surfactants as wetting agents for the suppression of sulphide ore dust has been investigated. Numerous surfactants were examined to determine their characteristics and to investigate their ability to improve the wetting of the sulphide ore dust. However, the surfactants selected as suitable dust suppressors proved to have a negative effect on the flotation of the ore contaminated with such reagents. A method was developed to eliminate the detrimental influence of dust-suppressing surfactants. It consisted of surfactants adsorption on activated carbon and separation of loaded carbon prior to flotation. The technique is simple and requires minimal changes in the plant flowsheet.

Jan 1, 1990

By Kevin A. Foo, Joseph L. Young, William W. Reid

The title of this paper is "Designing Very Large Bio-oxidation Plants". To our knowledge, only one such plant has been designed and built to date, and that is U.S. Gold's Tonkin Springs plant in Nevada. This plant was commissioned in Spring of 1990 and operated for a short time successfully as a bio-leach plant but U.S. Gold did not have the financial strength to overcome the consequences of construction delays and increased capital cost. The plant has temporarily been 1 put on a standby basis. Recently, < > a potential joint venture between Tonkin Springs Gold Mining Company and Homestake Mining was announced. Homestake will operate the mine with the technology and subsequent improvements would be co-owned by both companies. This paper is not a "how to" type publication because we feel that such an approach could be dangerous if used improperly. Rather, we discuss some of the important aspects of process selection, testing and design that need attention, and some of the lessons learned to date. As with all developments, improvements and new knowledge will accrue as more companies use bio-oxidation technology. The Tonkin Springs plant is fair evidence that bio-oxidation has "arrived" as a technology, and that successful design and operation of plants treating greater than 1000 t/d of feed is possible.

Jan 1, 1990

By J. R. Dyni

Colorado nahcolite deposits, estimated at 29 billion metric tons, formed in an asp metric permanent-lake basin whose waters were rich in algae and sulfate-reducing bacteria. Nahcolite (NaHCOg) occurs in oil shale of the Green River Formation (Eocene) as aggregates (62 percent), disseminated crystals (24 percent), and impure beds (14 percent). Because much of the nahcolite is nonbedded, it will be mined with oil shale and can be concentrated to marketable grade by crushing and screening Impurities in nahcolite are kerogen, quartz, pyrite, and carbonate minerals. A promising new market for nahcolite is in the process of removal of sulfur dioxide from industrial stack gases. When heated, nahcolite reacts with sulfur dioxide to form sodium sulfate. Differences in thermally induced microporosity may explain why nahcolite is more reactive than trona, a possible competitor with nahcolite for SO2 removal. Limited production of nahcolite at one or possibly two localities is expected in the next several years, but large-scale production is probably at least 10 years away.

Jan 1, 1980

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By J. P. Van Dillen

Continuing interest in processes that will effect separations in the fine particle size range has prompted intense interest in the use of high gradient magnetic separation (HGMS) for beneficiation of uranium ores. Some of the uranium minerals are paramagnetic and hence are amenable to concentration by HGMS. This paper presents a brief review of the problems associated with uranium ores beneficiation, a description of the HGNS process, and the effects of the parameters--pulp velocity, field strength, matrix loading and magnetic field gradient on product recovery and grade. Unsatisfactory separation of uranium minerals by HGHS is related to ore specific properties such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix and interference of micron sized slimes. Experimental techniques to identify and resolve some of these problems are outlined.

Jan 1, 1982

By Paul G. Schmidt

Exxon Minerals Co. was exploring for mineral deposits in Precambrian terranes of the US portion of the Lake Superior region in the late 1960s. Exploration drilling and other activities had been concentrated on massive sulfide prospects in northeastern Minnesota, but general exploration studies and competitor scouting were conducted in other areas of the region. These activities drew attention to Wisconsin in 1969 when it became apparent that Bear Creek Mining Co. had made a discovery near Ladysmith in the northwestern part of the state. Observation of their drill hole pattern suggested that a massive sulfide deposit, since named the Flambeau deposit (Schwenk, 1977), had been found. With this background, Exxon initiated an exploration program for Precambrian massive sulfide deposits in northern Wisconsin in 1970 (Figs. 1 and 2). Northern Wisconsin is extensively mantled by Pleistocene glacial drift and bedrock outcrop is sparse. Other than iron mines in the extensive iron formations along the Wisconsin-Michigan border and Jackson County, no significant mineral deposits were known in the Wisconsin portion of the Precambrian Shield until the discovery of the Flambeau deposit. Until the mid-1970s, the only specific published literature on the Wisconsin Precambrian consisted of old outcrop locations and descriptions in journals of the Wisconsin Geological and Natural History Survey (Chamberlain, 1882; [ ] Weidman, 1907; Hotchkiss, 1915) and the summary maps of Dutton and Bradley (1970).

Jan 1, 1991

By YU. F. Vasyuchkov, K. Vasioutchkov, B. M. Vorobjev

Introduction It is now believed that, even with the environmental protection measures now being taken, the further application of traditional coal-mining and electric power-generation technologies will inevitably cause further irreversible damage to the global ecosystem. Further improvements in conventional coal-mining technologies, both surface and underground, are expected to have only limited impacts on the economical, ecological and social aspects of coal mining. In countries with a developed coal industry, coal reserves with favorable conditions at shallow depths are rapidly being depleted. Therefore, in the future, more coal will be mined from deeper levels, resulting in higher operational costs and lower labor productivity. The solution to this problem is to be found in developing, promoting and implementing unconventional coal-mining and advanced clean-coal technologies. This paper presents an unconventional concept that has been suggested by the authors. The basic goal is to achieve coal-methane energy resource conservation and to remove barriers to energy efficiency through the adoption of integrated, ecologically clean, innovative technology. The following principles form the foundation of this concept: Energy resource conservation: This principle concerns the exploitation of actual and potential coal-methane reserves in the most effective way with the lowest possible losses and with the application of the most energy-efficient electric power-generation technology. Energy conversion: Energy conversion means the conversion of solid coal to synthetic fuel gas (in situ or in-cycle), the conversion of methane bounded within the coal matrix to free-flowing drained meth¬ane, the conversion of solid coal in situ to a coal/water mixture (slurry), and the conversion of these gas fuels into electric power. Technological and managerial integration: This prin¬ciple means an integration of coal-gas methane min¬ing operations and electric power generation into one commercial mine-to-product enterprise with electric power as the final product. Thus, coalbed methane drainage and coal gasification (both in situ and in-cycle) integrated with a combined cycle of electric power generation constitutes a highly integrated coal-gas methane energy-generation system. The system can be materialized in the form of a local integrated coal-gas electric power complex (LICGEPC). General features of the new concept The coal-gas-methane electricity concept is actually a synthesis of the following four technological components: Coalbed methane drainage. This technique and its utilization attained recognition after commercial operations were proven successful in the San Juan and Black Worriers coalfields in the United States. Worldwide, extensive field experiments and research-and-development activities are being carried out in the area of coalbed methane exploitation and utilization. Recently, coalbed methane drainage for power generation has been undergoing intensive research and development. At the Harworth Colliery in the United Kingdom, a combinedcycle power plant has been built that uses coalbed methane. The plant has an installed capacity of 15 MW Also, Germany, Australia, the CIS and China have conducted various experiments and industrial tests on the use of coalbed methane power generation. Underground coal gasification. Another unconventional technological approach is underground coal gasification (UCG). A number of semi-commercial, demonstration and pilot projects have been undertaken in Russia, the Ukraine, Uzbekistan, the United States, the United Kingdom, Italy and Belgium to demonstrate the technical and economical viability of coal gasification in situ. In Uzbekistan, the Angren coal-gasification station has been in full-scale commercial operation for two decades. The operation supplies a power plant with synthetic coal gas. Under sponsorship of the US Department of Energy&apos;s Morgantown Energy Technology Center, large-scale laboratory tests simulating coal gasification in situ were successfully completed by the

Jan 1, 1999

By Donna L. Boreck

In an effort to increase recovery in thick and closely spaced coal seams, the Bureau of Hines, U.S. Department of the Interior, is studying the feasibility of introducing three mining methods-high-face longwall, multi-slice longwall, and longwall caving-in western coal operations. Geology plays a significant role in determining the success of such methods. Some of the factors that will affect development are as follows: (1) thickness and three-dimensional configuration of the seam, (2) cleats, joints, and fractures in the coal and roof rock, (3) roof composition and variability, and (4) coal quality and changes in quality within the seam. Through geologic mapping, the presence of many of these factors is predictable prior to development.

Jan 1, 1987

By Edwin S. Smith

One of the many responsibilities of mining engineers and mill superintendents is to provide for the safe and economic disposal of wastes (or tailings) remaining after a mineral has been extracted from an ore. The cost of disposal of these tailings exerts a considerable influence on the minimum grade of ore extracted from the mine. It varies to a great extent with each project and is dependent on many diverse factors, such as the local topographical, meteorolgical, geological and seismological conditions together with the applicable water pollution laws of the area. The process used to extract a mineral from an ore determines the physical characteristics of the tailings and thus is one of the more important factors to be considered when planning disposal facilities. Today&apos;s trends .in ore-processing operations complicate the problems of waste disposal: recently developed extraction methods result in the production of finer tailings, the use of lower grade ores produces greater volumes of wastes, while the enhanced land values in the vicinity of industrial plants preclude the former practice of spreading wastes laterally and force the expansion of waste desposits upwards to greater heights. The frequent occurrence of stability problems in waste deposits indicates that many mining organizations may not be employing current soil mechanics concepts and practices. One of the most spectacular, and often most disastrous, types of tailings dike failure is that resulting from liquefaction of the fine particles combined with a breach of the main retaining dike.

Jan 1, 1967

By H. E. Goetzman

A cooperative research project supported by the taconite industry and the Minnesota DNR was undertaken to establish quality standards for carboxymethyl cellulose (CMC) based organic binders. The objective of this study was to identify the effect of CMC quality parameters such as degree of substitution, molecular weight, and purity as well as the effect of inorganic extenders such as sodium carbonate on performance. These factors have been evaluated by green-ball testing with two taconite concentrates followed by pot-grate tests. Balling tests with bentonite and Peridur were conducted to provide baseline data. At a constant DS the molecular weight as measured by viscosity had the greatest effect on green-ball drop strength. Dry-ball compression strength was most dependent on CMC addition rate and sodium carbonate content. DS was not found to have a major effect on green-ball quality for medium molecular weight CMC.

Jan 1, 1988

By B. Anameric

Considerable effort has been directed towards understanding the carbothermic reduction mechanisms of self-reducing, fluxing dried green balls to produce pig iron nuggets. Given the geometry of the situation, some investigators believed that the shrinking core model was applicable. Hence, this study involved investigation of the applicability of the shrinking core model to pig iron nugget production. The experiments involved heat treatment of dried green balls utilizing either a laboratory-scale resistance box furnace or a gas-fired muffle furnace at various furnace temperatures and residence times. The products were analyzed for the following: (i) preferred reaction pattern, (ii) distribution of the metallized areas, (iii) % iron content variation in the pig iron nuggets from surface to center, (iv) carburization pattern and (v) physical and chemical properties of the pig iron nuggets. It was determined that the reduction of iron oxide occurred simultaneously throughout the sample and not beginning at the surface and propagating inward; thus the shrinking-core model was not applicable. Heat transfer and gas diffusion from surface to center were not the rate-limiting steps for reduction and carburization reactions.

Jan 1, 2011

By Marcel F. DeGuire

Pilot plant operations are described for the treatment of manganiferous zinc concentrates from the Gamsberg ore deposit in South Africa via conventional electrolytic zinc processing. Two methods were employed for the control of excess manganese ions in the pilot plant electrolyte involving (1) chemical oxidation and (2) anodic oxidation. The chemical oxidation method for manganese control was very successful. It also was found that the addition of manganese dioxide ore was not required for oxidation of ferrous iron during the neutral leach or jarosite precipitation steps. A new method (JAR process) for iron removal also was tested in the pilot plant.

Jan 1, 1978

By S. Veeramasuneni

The interaction of soluble salt particles in their saturated brines is of interest from both a fundamental and practical perspective. The state of dispersion/aggregation of alkali halide particles as determined by optical microscopy can now be described based on non-equilibrium electrokinetic measurements for alkali halides. These results indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. These experimental results can be explained based on the interfacial polar interaction theory. In this regard the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems.

Jan 1, 1997

By G. B. Amicucci

A Denver Autometrics Particle Size Monitor, PSM-400, was installed at Golden Sunlight Mines, Inc. in October 1988. The PSM-400 measures the grind product&apos;s particle size and percent solids. The particle size is used to control grind size by automatically adjusting mill feed rate. The PSM&apos;s continuous response to ore changes has improved grind product uniformity and mill throughput. Metallurgical testing has shown the PSM&apos;s accuracy to be +/-1 % + 150 µm (100 mesh).

Jan 1, 1991