Search Documents

By P. W. Erickson

Development of the Twin Buttes mine entailed the largest known preproduction stripping job in the history of mining. It linked earthmovers and conveyor belts in a new approach to development of a pit that may reach, or even exceed, dimensions of 1 x 1-1/2 miles at the surface and go as deep as 1800 feet. The orebody to be stripped was covered by an average of 460 feet of alluvial gravels, which presented an initial stripping job of great magnitude. The initial pit layout and the original time schedule established early in 1965 called for the excavation and disposal of about 250,000,000 tons of alluvial overburden before the end of 1969. Allowing about a year for equipment delivery, this schedule left four years to do the job averaging about 62-1/2 million tons per year. In 1964 when The Anaconda Company undertook the development of Twin Buttes, it was recognized that special planning was necessary for the disposal of waste material and tailings. Environ- mental control was a prime consideration and is particularly sensitive in the Twin Buttes area due to the proximity to residential developments. Disposal of the 250,000,000 tons of alluvium, as well as future rock and tailing waste material, presented a problem which Anaconda engineers resolved by designing a plan to spread out much of the alluvium over an extended area, including a massive 11- 1/2 mile dike system which will impound mill tailing in three basins. The tailing will be impounded behind these-dikes to avoid wind exposure and blowing. The dikes also serve as a

Jan 1, 1974

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By A. G. Oppegaard

Most iron ores treated by the R-N direct reduction process yield metallic iron products considerably lower in titanium, manganese, and chromium oxides and alkaline metal sulfates/sulfides than were contained in the original ores. These metallic iron products are suitable as feed stock for the open hearth and electric steel-making furnaces. The elements which are rejected in part are acceptable in the product since the product is designed to by-pass the blast furnace. R-N reduction conditions (PCO+H2-1 atmosphere, 1830° to 2150° F.) are adjusted for each ore. The iron ore which is reduced to 90 to 95 percent metallic iron is then subjected to the conventional beneficiation techniques. Under these conditions, 55 to 80 percent of titanium oxides, 75 to 95 percent of manganese oxides, 60 to 90 percent of chromium oxides and up to 97 percent of alkaline metal sulfates contained in the ore are rejected with the gangue to the non- magnetic tailings. The metallic iron products illustrated in this work contained 89 to 96 percent total iron, one to five percent TiO2, 0.2 to one percent MnO, 0.3 to 1.6 percent Cr2O3 and/or up to one percent alkaline metal sulfide. Usually only one of these components was present. Recoveries ranged from 80 to 96 percent of the iron in ore.

Jan 1, 1958

By P. Somasundaran

Electrochemical properties of silicate minerals govern their behavior in processes such as flocculation and enhanced oil recovery that can occur at elevated temperatures. Knowledge of these properties as a function of temperature can be helpful in developing an under- standing of the role of these interfacial properties at non-ambient temperatures. Zeta potential of Sodium Kaolinite and quartz has been determined as a function of pH and temperature in this work. Both systems exhibited markedly different behavior at higher temperatures and also exhibited significant hysteresis. Results are examined in terms of possible dissolution of the minerals and surface reactions at different temperatures.

Jan 1, 1986

By M. Katzer

The effect of selective dispersants as wet grinding aids for ores is demonstrated on laboratory scale batch and continuous grinding equipment. A complete characterization of behavior is performed on a given ore to demonstrate correlations involving torque, % solids, net production rate, and slurry weight and volume loading. The relationship between such laboratory data and industrial scale testing results is very consistent.

Jan 1, 1979

By R. J. Sheets

"INTRODUCTION What is the primary responsibility for geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer – ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geo-engineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this paper will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face. WHAT IS OUR PURPOSE? A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question above. I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor groundwater levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: SAFETY. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or groundwater. The objective of a hydrogeologist is to ensure the soil or rock around an open pit or underground mine is dewatered; this specific objective will reduce pore pressures which could lead to a possible ground failure. They ensure a working bench/UG level is dry, so operations are not dealing with adverse conditions while mining. A geotechnical engineer is expected to use all available information and engineering judgement to provide design recommendations, so that the mine will not catastrophically fail. Additionally, they will implement the monitoring systems to identify hazards in advance in the event that the design is flawed and people need to be evacuated. We all know that safety is important to everyone; however, our particular set of technical skills play a significant role in ensuring the safety of a large portion of the global mining workforce."

Jan 1, 2018

By Dean H. Herrick

The production of crushed stone in the United States has exceeded 1.0 Gtpy since 1987. Eighty percent of the crushed stone produced is used in the aggregate industry, accounting for over half of the quantity of natural aggregate consumed in the United States. Approximately 718 of the crushed stone produced in 1989 was limestone and dolomite followed by granite, traprock, sandstone and quartzite, miscellaneous stone, marble, shell, calcareous marl, volcanic cinder and scoria, and slate in order of descending volume (Table 1). Of the remaining 20% crushed stone produced in the United States and not used as aggregate, 12% is used in the manufacture of cement which is an important construction material. Only 8% of crushed stone is used in specialty products not associated with the construction industry. Therefore, this chapter will concentrate on crushed stone as used in aggregates, with occasional reference to other uses or to chapters which discuss specific nonconstruction uses of crushed stone. Construction aggregates are hard, essentially inert materials suitable for being formed into a stable mass by the addition of cementing or binding materials that produce a concrete by compaction, or by natural weight to produce a road or foundation fill. Aggregates are usually from 80 to 100% of the material volume of the construction masses in which they are used. Conditions necessary for a rock deposit to be developed for construction crushed stone include: Quality-should pass rigid specifications for strength and durability; Quantity-adequate volume of rock is needed to have a production life of at least 10 years, preferably 20 or more years; Market-must have adequate market to support a new crushed stone operation; Transportation-transportation cost must be competitive for the intended market; Environmental-the impacts of mining, processing and transportation of crushed stone on the environment at or surrounding the mine site must be within acceptable limits; Permitability-mining, processing and transportation of crushed stone must usually be permitted by governing agency. The following discussion will touch upon all facets of crushed stone operations from the mineral deposit and its geology to technology, uses, economic factors and end with governmental regulations of mining crushed stone. The sections are not designed to answer all questions, but rather to be an introduction to the crushed stone industry. Where more information is required, The Aggregate Handbook by Barksdale (1991) is recommended as the best general source.

Jan 1, 1994

By James M. King

Analytical models for transient groundwater phenomena, such as those of Theis, Cooper, and Jacob, are important but often limited tools for aquifer evaluation and drawdown prediction. Most were developed using simplifying assumptions which compromise their treatment of complex boundaries and most also contain functions that are mathematically complex and difficult to solve explicitly. Examples of such functions are the Bessel functions, the exponential integral, and similar well functions for leaky confined and water table aquifers. This paper describes the joint use of simple numerical techniques and numerical approximations of these functions to extend many analytical models beyond their conventional applications. The enhanced analytical methods represent many hydrologic problems more easily and realistically, permit a wider range of application, and often provide insight into the response of pumped groundwater systems without the need to resort to more complex numerical flow models. Use of the enhanced analytical methods usually requires the use of microcomputers due to the large number of computations. Examples presented here are the development and extension of type curves and the determination of drawdown distributions.

Jan 1, 1984

By W. J. Schlitt, J. H. Templeton

The chemical reactions that occur within a copper-leach recovery system are discussed, and the impact on the overall acid balance is evaluated. Both oxide and sulfide mineralogy are addressed, and their effects on acid consumption, generation and solution buffering are presented. Two case studies that apply the discussed chemistry show the practicality of using a computer spreadsheet acid-balance model for the early planning and design of copper-leach systems.

Jan 1, 1998

By B. Weaver

Every year Pit & Quarry Magazine surveys the industry to produce their annual review. Here's a sampling of some of the statistics the survey produced from the end of the year 1994 survey.

Jan 1, 1995

By J. A. Finch, B. J. Huls

Accurate level detection is required to make full use of level in optimizing control strategies for flotation columns. Techniques based on pressure and electrical conductivity are compared. Pressure and conductivity profiles give good agreement on level. Level calculated from single and multiple pressure values became more accurate using, in order, one, two and three sensor locations. The level estimate remained in error, however, because, unlike the collection zone, froth zone bulk density varies with height. A conductivity probe continually updating the conductance profile is a practical method of obtaining an accurate level.

Jan 1, 1990

By Scott A. Norby

Kennecott's Ray Mines Division (RMD) is located in central Arizona. The pit and silicate plants are located at Ray while the 27,500 tpd concentrating facilities are located at Hayden, approximately 20 miles away from the pit. Ore is delivered in 100 ton railroad cars, 60 cars per train via the Copper Basin Railroad. The side discharge cars are dumped into a 6,000 ton trackhopper. There are 6 Nico feeders, two per belt. Three 48" belts transport the -8" ore to three 7' standard (secondary) Nordberg crushers. Each crusher is preceded by a 6' x 12' Tyler double deck screen. The secondary crushers are open circuit. The -1/21t material from the screens is transported directly to the fine ore bin at the mill. The discharge from the crushers and the intermediate product -2 1/411 x +1/2" is conveyed to a surge bin. The tertiary crusher feeder belts discharge onto five 61 x 161 Tyler double deck screens, each followed by a 7' shorthead (tertiary) Nordberg crusher in closed circuit. The -1/2" product joins the -1/2" ore from the secondary crushers and both are conveyed along a 42", 4,230 foot long belt to the fine ore bin that feeds the grinding circuits. When hard ore is experienced at the concentrator the daily throughput decreases by up to 10%. This coupled with the fact that the ore is generally becoming harder with mine depth provided the incentive to improve the performance at the crushing plant.

Jan 1, 1986

By Richard L. Sanford

The generalized rail haulage simulator described in this paper is an outgrowth of the need to expand a previously developed single level simulator to permit analysis of production problems where intermediate car storage is used. Many of the ideas of the former single level simulator, which is an integral part of an Underground Generalized Materials Handling Simulator (UGMHS), have been used in model development. In addition, experience gained in applying the earlier model to a variety of operating conditions has been heavily relied on. The generalized rail haulage simulation model can operate as an independent system and, as such, can be used to analyze rail haulage systems using production distributions as data input. In addition, this model is designed to replace the present rail haulage sub-assembly in the UGMHS model and the linking procedure has been integrated into the model. The flow of coal from production sections in UGMHS, for example, fill the mine cars and a condition of no empty cars at a loading station will shut down in by production systems.

Jan 1, 1974

By W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphalerite and dolomite, has been used to experimentally validate the model for the case of dry, batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1986

By Volkmar Niemitz

Approximately 30 miles east of Chicago on the southern shores of Lake Michigan stands Bethlehem Steel's newest fully integrated steelmaking facility - the billion dollar Burns Harbor plant. The initial phase of "green field" construction that began in 1963 was directed to the creation of high quality finishing facilities. In late 1964 the 160" plate mill came "on stream" followed closely by Sheet and Tin and Hot Strip facilities. Unit train shipments of slabs primarily from the Lackawanna plant located near Buffalo constituted the input materials for the new mills. In 1967 a hot metal facilities program was announced for Burns Harbor that at its completion would make the plant fully integrated. Incorporated within the program were: 1. A new high performance 50" x 96" slabbing mill complete with a battery of soaking pits. 2. A two vessel Basic Oxygen Furnace Shop. 3. (1) battery of 6 meter high Coke Ovens with attendant coal handling facilities. 4. A 3800 feet long vessel loading & unloading dock. 5. The first conveyor belt fed Blast Furnace in the United States. 6. An extensive materials handling system for receiving, stocking and reclaiming from storage the raw materials for the Blast Furnace and Coke Ovens operation. The intent of this paper is to provide a detailed description of the functions and components of the materials handling system noted above.

Jan 1, 1970

By R. E. Vivas, J. Garcia

"INTRODUCTION Freeport-McMoRan is a leading international natural resources company that operates large, long-lived, geographically diverse assets with significant proven and probable reserves of copper, gold, molybdenum, cobalt, oil and natural gas. Freeport-McMoRan is the world’s largest publicly traded copper producer and largest producer of molybdenum. The Sierrita mine is an open pit truck and shovel operation from which copper and molybdenum are produced. An important key to Sierrita’s success lies in their ability to realize their plans in the field. In certain circumstances, the mine plans are not achieved, and the operation fails to meet its targets which is an issue revealed in reconciliation reports. This technical session discusses the methodologies and procedures used at Sierrita to monitor the implementation of the mine plans, measure the performance of the operation and reduce the variance between plan and actual. Ensuring the operation stays on target is vital so mine productivity and profitability can attain its maximum potential. PROJECT OVERVIEW The Sierrita mining complex is located in Pima County, approximately 20 miles southwest of Tucson, Arizona as shown in Figure 1. The first mining claims at Sierrita date back to the late 1800s while underground mining activities started in the early 1900s. However, open pit development of Sierrita began more than 50 years ago to become the modern mining complex it is today. In 2009, Freeport-McMoRan purchased the adjacent Twin Buttes copper mine, providing significant synergies in the Sierrita minerals district. This venture included the potential for expanded mining activities, operations growth for mining copper and molybdenum, and reclamation activity. It should be noted that in addition to copper and molybdenum, the Sierrita mine produces rhenium which is a rare and highly value metal. The ore deposit contains oxide and sulfide mineralization. The oxide ore is delivered to the leach process while the sulfide ore is routed to the crusher and mill circuit 4,700 jobs on Arizona’s economy Freeport-McMoRan partners with the communities near Sierrita to provide programs that contribute to their sustainability"

Jan 1, 2015

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984

By J. J. Pavlica

Grinding in steel mills adversely affects the flotation removal of pyrrhotite from magnetite ores. To elucidate the effect of grinding media on the floatability of pyrrhotite, rest potential and short-circuit current measurements were made on electrode combinations of pyrrhotite-mild steel and pyrrhotite-stainless steel. Galvanic contact of pyrrhotite with mild steel increased the rate of surface reactions on pyrrhotite in air-exposed and oxygenated solutions. It was postulated that the formation of ' an iron hydroxide coating on the pyrrhotite adversely affected its floatability. Its formation was minimal when pyrrhotite was contacted with stainless steel. Fine magnetite particles caused slime coating on pyrrhotite surfaces by magnetic interaction and impaired the flotation of pyrrhotite.

Jan 1, 1982

By Wenming Wang, Edgar E. Vidal, Scott A. Shuey, Patrick R. Taylor, Judith C. Gomez

Introduction In modern society, vanadium is defined as a strategic metal. Some 90% of the global consumption is used as an alloying agent for carbon steels, tool steels, and high-strength low-alloy steels (particularly for pipelines). Advanced titanium-aluminum-vanadium alloys are seeing application in the aerospace industry. Small but ever growing amounts are finding application as catalysts or in electronics. New uses are continually being discovered for this metal. One example of a new application is the vanadium-redox battery for use in generation plants and back-up power sources. Vanadium is found in a large number of minerals, of which the most important are carnotite, roscoelite, vanadinite, mottramite, and patronite. Just over a third of the world's vanadium is produced as a primary product; the balance is a by-product of the iron and steel, oil refining, power generation and uranium enrichment industries. Vanadium can also be sourced by recycling spent catalysts from the petrochemical industry and ash produced by the combustion of oil emulsion in power stations. However, recycling activities are believed to account for only a small amount of total world supply. Vanadium is recovered from these ores largely as the pentoxide (V2O5) [1]. The major sources of vanadium-bearing magnetite ores are scattered throughout Australia, China, Russia, and South Africa. Current estimates of world’s Proven & Probable vanadium reserves are of the order of 41.3 million tones [2, 3]. Commercial vanadium-bearing titaniferous magnetite deposits can be found in Kachkanar, Russia; Pan Zhihua, China; Bushveld, South Africa; and Windimurra, Western Australia [4]. Other deposits have been found in New Zealand, Canada, and India, among other countries. Vanadium consumption in the steel sector has increased some 7% per ton of steel over the last 10 years as new alloying applications have been found to improve steel's strength-to-weight ratio. Future demand from the aerospace and nuclear industries for non-ferrous vanadium alloys such as titanium and super-alloys is also likely to grow. Vanadium is usually added in the form of ferrovanadium, a vanadium-iron alloy. Vanadium compounds, especially the pentoxide form, are used in the ceramics, glass, and dye industries, and are also important as catalysts in the chemical industry. While established approaches may be used at an industrial scale to treat vanadium-bearing titaniferous magnetite ores in several countries, new alternatives are being developed worldwide. This review will give short overview of the treatment of vanadium-bearing titaniferous magnetite ores, an overview of direct reduction and direct smelting processes and an approach to determine technical alternatives for the property.

Jan 1, 2005

By Z. D. Hora, W. N. Hamilton

Evaporite units of the Western Canadian Sedimentary Basin are known to host native sulfur. In British Columbia, a large number of oil and gas exploration drilling holes reported intersections with native sulfur. The most important ones include 6 meters (20 feet) and 27 meters (90 feet) of native sulfur among 23 occurrences in Devonian Muskeg evaporite or adjacent Slave Point reef facies carbonates. A small Frasch sulfur deposit is known from Devonian Wabamun Group sediments near Camrose in South Central Alberta. Occurrences of native sulfur are common also in association with presently mined gypsum of Devonian Burnais Formation in southeastern British Columbia. Triassic sediments with evaporite members in British Columbia are also known to contain native sulfur showings. A widespread presence of anhydrite in many sedimentary units of Alberta and British Columbia together with oil and gas fields in the same areas and associated native sulfur occurrences point to a possibility for Frasch sulfur deposits in this part of western Canada.

Jan 1, 1992