Search Documents

By Paul C. Schmall, Thomas Tuozzolo, Arthur B. Corwin

The Lenox Avenue Reconstruction Project involved the excavation and replacement of 750 m (2,500 ft) of deteriorated subway invert concrete, 5 to 7 m (15 to20 ft) below water table in very permeable ground. The Replacement work was done over an 8 month period, while maintaining track service through this subway section. The project was dewatered with a single 125 l/s (2,000 gpm) wellpoint system,750 m (2,500 ft) in length, which was installed from inside the active tunnel structure and configured to coexist in the subway tunnel with operating trains as well as the construction activities. A thin diaphragm jet grout wall was utilized on one end of the site to cut off the flow of water across a difficult geological interface that was situated immediately below the tunnel invert. The thin diaphragm jet grout wall permitted the large 116th Street Station area to be dewatered completely with well points from outside of the excavation.

Jan 1, 2001

By R. K. Dunham

It has been estimated that 30% of the United States coal reserves occur in the Western States at depths which would preclude exploitation by surface techniques. Much of this coal occurs in seams considerably thicker than those presently mined in other parts of the country. Recognizing the lack of technology and experience in exploiting the thicker seam range the Interior Department's Bureau of Mines is implementing a major "Mining System for Western Coal," research program which has as its ultimate objective the development and demonstration of underground mining methods and technology for extracting these seams. One investigation, being carried out by D'Appolonia Consulting engieers, under contract to the Bureau of Mines, is concerned with design of an entry system for longwall top slicing of thick western coal seams. This presentation presents an overview of some of the problems which have to be faced in designing such layouts.

Jan 1, 1977

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986

By J. C. Poulos

The West Elk Mine is located near Somerset, Colorado approximately 70 miles southeast of Grand Junction, Colorado and 72 miles southwest of Glenwood Springs, Colorado on state highway 133 (Figure 1). The West Elk Mine was opened January 20, 1982 as the Mount Gunnison #1 Mine operated by the West Elk Coal Company, a division of ARCO Coal. In the early 1990?s ARCO changed the mine name to West Elk Mine and the operating company was renamed Mountain Coal Company. Arch Coal, Inc. purchased the West Elk Mine in 1998. West Elk Mine has produced coal from three different seams. Coal was first mined from the F Seam, the upper most seam in the stratigraphic sequence, from 1982 through 1991. Coal was produced from the B Seam, the lower most seam, starting with continuous miners in 1991 and transitioning to longwall mining in 1992and continued on through October 2008. The development of the E Seam, which is the middle seam in the stratigraphic column, started in 2004 with longwall production commencing in 2008. The ventilation conversion from exhausting to forcing for the E Seam portion of the West Elk Mine was implemented in late October 2009.

Feb 27, 2013

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

By Ralph M. Foecking

The disposal of the phosphate slimes produced by Florida beneficiation operations is perhaps the biggest single problem of the phosphate mining industry. This is an old problem which has not been solved and which is becoming increasingly severe. In a typical phosphate mining operation, the phosphate rock mined is initmately mixed with sand and clay, constituting what is known as matrix. During the beneficiation, the clay and other fine materials are separated usually at -150 mesh, and washed from the phosphate rock in a form of diluted slurry known as phosphate slimes. The quantity of slimes solids and their composition vary considerably with the location but usually represent from 25 to 35% of the ore mined. Because of the affinity that clays have for water, large volumes of water are required to separate the granular material in the matrix forming a dilute slime suspension (1.5 to 3% solids) of colloidal material, which settles very slowly, and thus requires immense impounding areas, which never becomes totally usable land. These ponds also contain about 25 to 35% of the total P205 values mined. The magnitude of the problem represented by the slimes can be appreciated better if we realize that there are around

Jan 1, 1971

By Nathaniel Arbiter

In contrast to pyrometallurgy's 6000year history in metals production, hydrometallurgy is of relatively recent origin. The earliest reference to it was in the 16th century, with the first applications to copper in the 17th and 18th centuries. In the 19th century, increased demands for pure metal resulted in the development of electrolytic refining, and early in this century electrowinning. The rapid growth in copper production in the 20th century, particularly in the United States and Chile, stimulated the development of new technology for leaching and for the recovery of copper from leach solutions. In the past 25 years, solvent extraction has become a major factor by permitting novel leaching technology that produces dilute or complex solutions. In addition, solvents other than sulfuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends that should grow in importance with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed. Key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared with that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1994

By James M. Harrington, A. Azra Bilgin, JoAnn Silverstein

The prevention of AMD in situ is more attractive compared to subsequent downgradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied in an abandoned mine pool with a pH of 3-3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2005

By Georgene Renner

At the beginning of the 1990s, Communism fell and signaled the end of the Cold War. The world rejoiced but also watched and waited to see how those countries would restructure themselves. The 1990 SME Annual Meeting was held at the Salt Palace Center in Salt Lake City, UT. The keynote session featured Alistair Frame, chairman of RTZ; Paul Queneau, professor of metallurgy at the University of Utah; and TS Ary, director of the U.S. Bureau of Mines. The SME Board of Directors voted to hire a Manager of Public Information and Education to be the GEM Program coordinator. This person was to collect and disseminate information that could be used by individual members and Local Sections to interface with government personnel and the general public.

Jan 1, 2007

By S. M. Pickering

Banks frequently manage large privately owned mineral land trust accounts for estate heirs. The bank has a fiduciary obligation to follow the “Prudent Man Rule”, which requires that trust properties be managed at least as well as a prudent and knowledgeable owner could. However, banks may not have internal staff proficient at mineral property values, lease contracts, royalties, mining practices, etc. This is an opportunity for experienced geologic consultants and certified minerals appraisers to provide needed help. Items valuable to Trust managers may include: 1. Marketing privately owned mineral trust lands to mining or oil & gas firms, assuring competitive offering prices and terms; 2. Negotiating favorable new mineral lease and purchase-option contracts; 3. Monitoring progress of mining, royalty payments, land reclamation, and environmental clean-up work; 4. Balancing future mining income with later industrial, commercial or housing development, timber harvest, etc.; 5. Assuring that Depletion Allowance tax advantage is taken for actual mine royalty payments, but not for annual non-mining lease (rental) income; 6. Appraising in-ground mineral value for bank audits, estate tax valuations, and equitable property division between heirs; and 7. Serving as expert witness, representing the legal interests of the bank, trusts, and the mineral heirs in litigation. Banks do welcome reliable advice which assists them in achieving the “Prudent Man Rule” and improving mineral income to their land Trust accounts.

Jan 1, 2002

By Mark P. Juzli

During the 1980s, a revolution has been taking place in industrial minerals marketing. Transportation deregulation and a handful of creative marketing and distribution managers have completely changed the rules for marketing many industrial minerals. Minerals are being transported much farther than in prior decades and at much less cost. Bulk and package terminals are becoming increasingly common as a means to take advantage of freight rate savings and to provide enhanced service to faraway customers. Water and rail transportation are being used increasingly to penetrate markets considered unreachable just a few years ago. No longer do the textbook rules of thumb for industrial minerals marketing apply. This author recalls three of those rules he was taught in mineral economics graduate school in the 1970s. As recorded in class notes: • construction aggregates are seldom shipped more than 32 km (20 miles) from the quarry; • cement is sold within 240 km (150 miles) of the mill; and • industrial sand is sold regionally - it is freight constrained to a market radius of no more than 320 to 400 km (200 to 250 miles) from the plant. And yet, the author looks up in 1989 and observes overland movements of aggregates of many hundred miles, overland movements of cement and industrial sand of 1600 km (1000 miles) or more, and water movements of both aggregates and cement into the United States from sources halfway around the world. Truly, industrial minerals are in the midst of a marketing revolution. The companies that have led this revolution have enjoyed considerable financial success in the 1980s. They have enhanced their profitability by increasing market share, capacity utilization, and average selling prices by taking product to remote markets where premium prices are available. They have consistently outperformed their competition, many of whom remain unaware that the marketing revolution going on around them is actually a transportation/distribution revolution. The successful industrial minerals company of the next 10 to 15 years must participate in the transportation revolution as it continues to evolve. Additional human and capital resources must be committed to maximize the effectiveness of a company's transportation and

Jan 1, 1989

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002

By Roy Woodall

Successful mineral exploration is the lifeblood of the mining industry. Contrary to what the environmental lobby would have the world believe, the industry is replacing the metals it is extracting. The reserve base has not changed significantly in 20 years (Fig. 1.) Mineral exploration is a research activity. First there is the idea, the vision or the intuitive thought. The experiments follow. These involve repeated phases of data gathering, data interpretation and concept testing through drilling. For many companies, exploration is the main investment in scientific research. Each mineral exploration experiment may involve years of costly work. Despite the improving tools of science and technology, the investment remains high-risk. Only the promise of high rewards, or desire to survive as a mining company, will stimulate the necessary commitment and level of investment. Confidence that an economic return can be achieved, confidence in the science and technology being applied and confidence in the people involved are the foundations upon which successful mineral exploration is built (Woodall, 1984). The challenges facing the explorationist in the 1990s fall into two categories: - the challenge to make the activity economic; and - the challenge to make the activity socially and, therefore, politically acceptable.

Jan 1, 1992

By K. Lapakko

Several static tests estimate the capacity of mine waste to produce and neutralize acid and are used as tools for predicting metal-mine waste drainage quality. Various methods and their accuracies are addressed. More accurate quantification of these capacities, as well as their availability and reactivity, may be necessary to predict drainage quality from some mine wastes. Chemical analyses, x-ray diffraction, optical microscopy, scanning electron microscopy, and electron beam analyses are among the techniques commercially available to more accurately quantify these capacities and provide insight into their availability and reactivity.

Jan 1, 2003

By Guosheng Zhan

The Homestake Mine included the open cut and underground workings up to 2,484 m (8,150 ft) deep. The mine ceased mining activities in December 2001 after 125 years of operation. Pumping from the underground workings continued for 18 more months until June 10, 2003. Homestake had completed a comprehensive hydrologic evaluation on post-closure underground flooding prior to the shutdown of pumping. After closure, the mine was selected by the National Science Foundation as the site for the Deep Underground Science and Engineering Laboratory (DUSEL). An interim laboratory facility will be set at the 1478 m (4850 ft) Level. The final facility will be set at the 2256 m (7400 ft) Level or deeper. Pumping from the underground workings began on June 5, 2008 by the South Dakota Science and Technology Authority (SDSTA). During the period of June 2008 through March 2009, the pumping rate increased from 41 L/s (650 gpm) to 81 L/s (1,290 gpm) with an average rate of 60 L/s (950 gpm). As a result, the water level had been lowered more than 95 m (310 ft). It was found that the observed rebound and later decline to date is in close agreement with the model projections. Because of this, the authors of this paper reject claims of a lack of sufficient measurement devices in place and a lack of understanding of the hydrologic system at the Homestake Mine prior to shutdown of pumping in 2003 (Davis et al, 2009). Furthermore, it is believed that this validated model can serve as a useful tool for the SDSTA to manage future underground dewatering for the DUSEL operation. This paper evaluates the hydrologic conditions in the Homestake Mine area and projects the post-closure groundwater rebound and decline due to DUSEL pumping.

Jan 4, 2010

By R. M. Owens, J. F. Lupo

The Shirley Basin Uranium mine, located in southeastern Wyoming, USA, was an open pit mining operation consisting of a series of several open pit mines excavated into poorly consolidated sandstones, siltstones, and claystones. Since the initial open pits were developed in 1969, slope failures have plagued the mine and mining operations. These slope failures have persisted into the current mine reclamation period. When the mine was first developed, the open pit slopes were designed to range between 45 to 55 degrees. Numerous slope failures during mine development required the pit slopes to be redesigned with slopes as shallow as 26 degrees. At present, movements are occurring within the open pits on reclaimed slopes that are shallow as 12 degrees. Several detailed slope studies were conducted at the mine in the early 1970s. These studies, combined with more recent geotechnical investigations, provide a unique detailed history of pit slope failures on shallow slopes. This paper presents an evaluation of the slope failures at the Shirley Basin mine, highlighting important mechanisms causing slope failures on very shallow slopes. The evaluation demonstrates important key parameters for shallow slope design.

Jan 1, 2001

By Lorenzo Pellegrini

The respect of EPB reference pressure during TBM advance and hyperbaric activities, the complete and effective filling of the annular gap between tunnel lining extrados and the excavation section and a well organized monitoring system, to control surface settlements and ground distortion, are items of utmost importance in EPB tunnelling process. The paper describes how these concepts have been applied while excavating in the difficult underground conditions found at Sao Paulo (Brazil) during the execution of the Sao Paulo Metro Line 4-Lot 1. In this project, the annular gap has been filled by two components type, cement grouting. The back feed of the extensive monitoring campaign carried out to check the surface settlements during the excavation and hyperbaric maintenance operations will also be described in the paper.

By Wayne N. Marchant

Introduction The issue of coal mining safety plays an important role in the United States' growing dependence on coal to supply its future needs. This article will address the federal government's role, principally the US Bureau of Mines, in meeting this challenging growth and demand while reducing the social and economic costs attributed to injuries and fatalities in underground mining. Some interesting facts and projections with respect to the nation's energy picture will be discussed. This includes the distribution of its reserves and the projected role of coal in the energy and economics of the nation's future. Underground mining will continue to be an important means of providing this coal. The author will discuss how the Bureau of Mines' research program addresses the problems of health and safety that grow out of the demand for more coal. Future projections First, a synopsis of salient facts and projections concerning the US's situation with respect to energy and the economy. Figure 1 depicts the relative quantities of recoverable energy reserves in the United States by their type. Most people are aware of the nation's use of oil. We hear a lot about natural gas. And we are aware of the controversy over the use of nuclear energy. But, while looking at Fig. 1, the question becomes, "Where will our fuel to meet the demand for energy in the future most certainly have to come from?" With 82% of the nation's recoverable fuel reserves being coal, the answer is irrefutable. Coal will be that source. Figure 2 is the present market for coal. It shows that 77% of the coal mined goes to supply electric utilities. Therefore, the coal industry as a whole is most sensitive to the trends and demands for electricity. It is less affected by what happens in other markets, such as export and direct industrial use. In fact, the coal industry is three times more sensitive to the electric utility market than to all other markets combined. Therefore, the trend in the demand for electricity must be examined. Electricity demand is expected to increase steadily over the next 15 years. It is projected to grow from its present 2.3 trillion kWh per year to 3.5 trillion kWh per year by the year 2000. The fuel to supply this increase in demand must come from somewhere. The question is "How much of this extra fuel will be coal?" Although the demand for electricity is predicted to increase, the demand for coal does not necessarily follow. Coal must maintain its fraction of the energy sources used for electricity generation if its demand is to increase at the same or greater rate as electricity. Except for a near-term dip in demand due to a slight increase in nuclear capacity, the domestic electric generation accruing to coal will go from 56% in 1985 to more than 60% in 2005. Thus, the predicted trend is for coal to become a larger part of the fuel mix for electric power generation. Similarly, looking at the most recent forecast for total coal consumption trends, it can be seen that for electric power generation alone, the coal industry must be able to supply an additional 316 Mt/a (348.5 million stpy) by the year 2000 (Fig. 3). It must be stressed here, though, that without significant improvements in mining safety, it can also be easily predicted that injuries and fatalities will increase in proportion to the increase in coal production. Will society consider that acceptable? This author does not believe so. Figure 4 examines the effect of coal prices on the price of electricity. The projections show that the already high proportion of fuel cost will become a greater fraction of the consumer price for electricity. Specifically in 1985, 36% of the price of electricity was the cost of the fuel. In 1995, 46% of the price of electricity will be the fuel cost. That implies that the price of coal will have an increasing influence on the consumer price for electricity. Thus, as coal is used more to generate electricity and as fuel becomes a greater

Jan 4, 1987

By W. G. Pariseau

Conventional barrier pillars in underground coal mines are intended to protect mains and sub-main entries for relatively long periods of time. Inter-panel barrier pillars that may be used in especially deep coal mines, say, below 800 m (2,400 ft), are intended to protect longwall panel faces and adjacent panel entries for the life of nearby panels. Barrier pillar failures have serious consequences, especially when failure is sudden and catastrophic. Design of barrier pillars is thus of considerable importance to safety and efficiency of operations. Locally, failure occurs at the limit to elasticity when stress tends to exceed strength. Strength of rock is stress dependent, so an analysis of stress is central to rational design of barrier pillars. There are several approaches to stress analysis for coal mine pillar design that range from the simplified but popular tributary area method including variations that use empirical definitions of the tributary area (volume) to more sophisticated numerical methods such as the boundary element method and the finite element method. Despite ease of use, empirical methods are limited and always suspect when applied to conditions beyond their scope of definition, while boundary element methods do not generally include pillars in the solution domain. The finite element method is not so restricted and thus is a natural choice for conventional and inter-panel barrier pillar safety analyses. Caving of roof strata certainly affects the distribution of stress about longwall faces and nearby barrier pillars. Conventional wisdom that considers roof strata to respond as cantilever beams indicates the longer the span the greater are loads on longwall faces and face supports. Failure of roof beams, caving, shortens spans and relieves face and support loads. The same view is applicable to barrier pillars in that long roof spans outside of barrier pillars leads to higher pillar loads than short spans. Hence, caving should be beneficial to barrier pillar safety. However, the benefit may be small depending on the extent of caving and only in the form of a slight reduction in overburden weight transmitted to the barrier pillar, especially in case of inter-panel barrier pillars. FINITE ELEMENT MODEL Finite element models for stress analysis in rock mechanics are formulated in consideration of physical laws, kinematics, and material laws. These models meet the essential requirements for equilibrium of stress, satisfy strain displacements relations, and in a general sense, relate stress to strain through material laws, often referred to as constitutive relations. The last may be complex and replete with nonlinearities. A de facto engineering material law is the elastic model in the form of Hooke?s law for linear, homogeneous materials that may be anisotropic. A limit to elasticity is imposed by strength in the form of a failure criterion or yield function that accommodates triaxial stress states. Examples used in rock mechanics are the well-known Mohr-Coulomb (MC)criterion, the popular Hoek-Brown (HB) criterion, and the Drucker-Prager (DP) criterion. The first is linear in stress, while the second is nonlinear. Both do not include any effect of the intermediate principal stress. The last is also linear in stress but includes the intermediate principal stress. All show an increase in the major principal stress at failure with confining pressure. In the UT2/3 finite element programs, the failure criterion Y is a nonlinear, anisotropic form and is also the plastic potential [1]: [YJI=+ 11NYJI=+- (1) ] where N is an exponent, usually 2, and J2 and I1 are nonlinear anisotropic forms of the second invariant of deviatoric stress and the first invariant of principal stress. The form (1) reduces to DP when N=1and isotropy prevails. When Y = 1, the limit to elasticity is reached and plastic deformation is possible. The material constants that enter (1) are all computed from unconfined compressive, tensile, and, in case of anisotropy, shear strengths. These latter strengths may be estimated from conventional laboratory test data. Of course, joints in field-scale rock masses induce different values. How different is often a matter of conjecture. For comparative studies, laboratory rock properties seem adequate. Inelastic, that is, plastic behavior occurs with strain beyond the elastic limit. Strain hardening, ideal plasticity, and strain softening are possibilities. Ideally brittle behavior with complete loss of strength is an extreme form of strain softening [2]. Caving may also be considered as strain softening with a less drastic reduction of material properties. As intact roof strata fail, fall, and form a rubble pile below, a new material is formed with greatly reduced elastic moduli and strengths, say, 1/100th of the original intact moduli and strengths. From another viewpoint, caving is simply a natural cut and fill process. Input for stress analysis by the finite element method includes: 1. Preexcavation stress state 2. Geology (stratigraphic column) 3. Structure (major faults, joint sets) 4. Elastic moduli 5. Strengths, and specific gravities of each rock type 6. Excavation sequence Output from an analysis includes distributions of: 1. Stress 2. Strain 3. Displacement 4. Local factor of safety (element fs) The last is defined as the ratio of strength to stress and in view of the failure criterion (1), is the ratio [fsJstrengthJstress=] where the numerator is the maximum possible value and the denominator is the actual value of the square root of the second invariant of deviatoric stress. This invariant is a measure of shear stress intensity but also reduces to uniaxial tensile and compressive strengths as the case may be. An fs greater than 1 indicates an elastic state of element stress; a value of 1 indicates the limit to

Jan 1, 2009

By Aram Grigoryan

This paper addresses historical aspects and construction sequencing of the subway complex under Columbus Circle in Manhattan; the structural elements of the rehabilitation and new construction; and the challenges associated with design and construction. PB is providing engineering services to New York City Transit (NYCT) for the rehabilitation of the 59th Street/Columbus Circle Station Complex that services over 150,000 customers daily. The project involves structural repairs, modifications and new construction requiring underpinning and temporary supports, custom framing details, and construction staging procedures to meet stringent limitations within the operating transit station and around the Columbus Circle street intersections.

Jan 1, 2008