Search Documents

By Dennis A. Beiter, Kenneth G. Fields, Richard T. Stoltz

Section 56.5001 Title 30, [Code of Federal Regulations1], establishes requirements for respirable dust exposure in Metal and Nonmetal Mines based on the Threshold Limit Values (TLV's) adopted by the American Conference of Governmental Industrial Hygienists. Respirable dust samples collected by Mine Safety and Health Administration (MSHA) inspectors at a sandstone quarry showed certain workers were exposed to excessive concentrations during development of a "coyote tunnel" that was ventilated with a blowing system. Because exhausting face ventilation systems are known to control dust more effectively than blowing face systems, a change was proposed to improve worker respirable dust exposures. This paper describes the evaluation of the proposed exhausting ventilation system in the quarry's "coyote tunnel" and compares the respirable dust exposures with those measured by the MSHA inspectors with the blowing system. Results showed the proposed exhausting ventilation system reduced respirable dust exposures to less than 20 percent of those measured by MSHA inspectors when the blowing system was used.

Jan 1, 1993

By L. B. Rothfeld, R. L. Dolzani

This paper presents preliminary results of a US Bureau of Mines (USBM) study of potential costs of compliance with possible federal regulations for copper heap and dump leaching. The regulations could arise under amendments to the Resource Conservation and Recovery Act (RCRA) and/or the General Mining Law. Estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the cost of compliance with 1992 state requirements for terrains typical of those found at existing copper leach sites in the southwestern United States. Incremental compliance costs are found to widely exceed screening criteria used by the US Environmental Protection Agency (EPA) to denote significant economic impact.

Jan 1, 1995

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By R. Schuerch, C. Cimiotti, M. Piemontese, N. Karlin, P. Perazzelli, P. Halton

The new Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to White Point Manifold. The tunnel will be approximately 7 miles (11 km) long with a finished internal diameter of 18 ft (5.5 m). The TBM is designed to cope with high water pressure up to 10 bar. The geotechnical challenges are due to the heterogeneous subsurface conditions: in the first half of the alignment, the tunnel runs through soils with a low overburden under urban areas, and, in the second half, the tunnel runs through extremely weak, intensely faulted rock masses with high overburden. Following an overview of the project, this paper focuses on the northern portion of the alignment and presents a decision-making procedure developed during pre-excavation phase in order to cope with the expected heterogeneous conditions during mining. The risk assessment and the TBM operational design of the southern portion will be dealt with in a future paper.

Jun 13, 2023

By Nath S. Parate

With the extension of mining beneath residential and industrial areas, it is becoming increasingly necessary to extract coal and minerals in such a way that subsidence damage due to groundmovement is reduced to a minimum. Understanding clearly of the mechanism of subsidence development is a must in view of the environmental problems and the energy crisis today. This paper gives a simple analysis of various components resulting from subsidence and the influence of other factors on their development. An up-to-date review of the subsidence and strain profiles is presented, with particular references to the coal mining operations. The importance of this topic from mining damage to structures, buildings properties and environment in mining areas is undeniable. Field results are discussed.

Jan 1, 1982

By H. J. H. Pieterse

This paper highlights the mineralogy of the Barrick Goldstrike Mines Inc. area. The mine is located at the north end of the Tuscarora Spur and is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend. The Betze, Post, and Meikle Mine are major deposits located in the area. The deportment of gold, its leachability, and various process options are also evaluated. Particular emphasis is given to the practical and economic considerations of ore control, and routing of ore to a process option.

Jan 1, 1993

By Katherine Hynard, Colin Eustace

Development quarterly mine plans is generally time-consuming and requires consideration for many operational constraints and competing objectives. With lengthy turnaround times, there is often limited opportunity to adjust the quarterly plan details to account for differences between actual state of the mine operation at the time of execution and expected state at the time that the plan was developed. Actual mining task completion times can vary significantly from the expected task completion times, due to many factors. In the absence of revision to account for differences between the planned and actual state, resource allocations and mining sequences, embodied in the quarterly mine plan may no longer be the best approach at the time of execution to achieve an efficient mining operation. Simulation and optimisation tools can be used to support rapid refinements for development and execution of weekly mine plans. When initialized with an operations data feed to establish the actual state of the mine operation, optimisation models can be used to facilitate both automation and revision of the quarterly plan to produce a weekly or daily plan for execution. This approach can remove much of the manual burden of revision if the existing quarterly plan no longer represents the best approach to meeting production objectives. Following initialisation with mining actuals, simulation models can provide a representation of the range of likely mine operations outcomes. The models can be used to accelerate the planning process by providing visibility of future performance and identifying likely operational issues. They can also be used to test the robustness of the plan with respect to performance variability and response to disturbances. Following identification of issues, simulation models can also be used for evaluating mitigation measures, through automated testing of alternative plans. Integration of mine data feeds with simulation and optimisation tools enables automated optimal responses to variations between the quarterly mine plan and actuals to be tested prior to release of and execution plan and implementation. The use of simulation and optimisation in weekly mine planning will be discussed in this paper with reference to surface mining examples.

Jun 25, 2023

By Wi11iam I. Rau

In the recent past, there have been numerous projections of the capital requirements for additional mine and processing capacities required to meet projected non-Communist World demand for minerals during the next 15 years. A consensus judgment would place this currently at $14 billion per year, with the largest expenditures required for increases in aluminum and copper production. Until the early 1960's, internally-generated funds were used to finance nearly all of the large mining companies' capital requirements. Since that time, however, the enormous rise in capital costs per ton of capacity, accompanied by a relative stagnation in the financial condition of many of the major mining companies, have caused the industry to begin to rely on external sources for financing expansion, most notably, project financing from commercial banks and institutional lenders. Seven years ago, it was estimated that, in the five-year period 1972-1976,75% of the total capital requirements of $10 billion per year would come from internally-generated funds, with the balance to be provided by external sources. l There is little doubt that, in the coming decade, the percentage provided by external sources will increase. There should be little difficulty in attracting the necessary investment within the U.S., particularly in view of the expected continuation of companies in diverse industries seeking mineral investment opportunities. The more serious question lies in the availability of internal and external sources of funds for the expansion of mine and smelting capacity in the developing countries. Recently, R. F. Mikesell projected an average annual investment of $4.7 billion (in 1977 prices) over the 1977-1990 period would be required from foreign sources to expand metal producing capacity in developing countries. Mikesell concluded that external financing of mining projects in the developing world has averaged less than $1 billion per year over the past five years, thereby requiring more than a quadru1ling of this financing over the next decade.

Jan 1, 1978

By J. O. Guthrie

Newmont has delineated a 600,000+ ounce gold reserve in the Cargo Muchacho Mountains. This is a desert range underlain by Proterozoic(?) Tumco Formation (gneiss) intruded by Jurassic granitic plutons, and cut by low angle shears of the late Cretaceous Chocolate Mountain Thrust event. Gold, associated with pyrite, quartz veinlets, and propylitic alteration, is emplaced along low angle shears. The mineralizing system, enriched in tungsten, copper, zinc and arsenic, was active during Eocene time. Gold reserves are found in eleven areas as moderate to high tenor deposits that may be mined by open pit and underground techniques. Eastmaque Gold Mines Ltd. is developing the deposit.

Jan 1, 1987

By A. E. Reisenauer, R. W. Nelson, G. W. Gee

A model assessment was made to evaluate contaminant transport to ground water from clay-lined and unlined tailings pits. The input hydrologic soil characteristics were measured on materials typical of those found at the Morton Ranch uranium mill site in central Wyoming. The assessment involved combined saturated and partially saturated flow and contaminant transport models for two-dimensional cross-sections typical of the proposed Morton Ranch burial pits. Specifically obtained from the models were contaminant flow paths, the advancing contaminant flow fronts for sorbed and non-sorbed constituents, and travel times of contaminants along flow paths. Such results enable evaluation of the environmental consequences for the alternative control methods.

Jan 1, 1980

By Steven J. Kirk

In the past decade, many hardrock surface miners have revegetated dumps and tailings ponds to allow those waste disposal areas to blend more easily with the surrounding landscapes. Efforts have also been made to more creatively use the flat land resulting from the disposal of overburden and tailings. However, the mines which serve the best post-mining land uses are those that have been preplanned to incorporate such end uses. To more fully explore such a philosophy, interdisciplinary team from The University of Arizona conducted a study during 1974 and 1975 of six open pit copper mines in the Santa Cruz River Basin south of Tucson, Arizona for the purpose of investigating both interim and end-use possibilities for mine waste disposal areas. Among other reasons for the study, it was felt that alternatives for such waste areas would be more socially acceptable than barren dumps or tailings ponds. The team, known as the Mines Project Group, consisted of architects, engineers, and hydrologists. As it would have been economically infeasible to move the existing waste rock dumps or tailings ponds, preplanning was limited to the disposal of waste generated after the inception of the project. To better present their concepts, architecture professors Kenneth Clark and Fred Matter constructed a large-scale cardboard relief model of the mines and the surrounding Santa Cruz River Valley (1). The model was built at a scale of 1:12 000 (1 in = 1000 ft) with 30.48 m (100 ft) contour intervals and covered an area of 40.23 km by 32.18 km (25 miles by 20 miles) in scaled area. The mines being studied were cut into the model, but the proposed waste dumps and tailings ponds were built separately so different disposal configurations could be evaluated.

Jan 1, 1980

By Wenbing Guo, Mingjie Guo, Hebing Zhang

As resources are depleted in coal mines, isolated support pillars are often mined. Cemented paste backfill has been used to provide support during the mining of these pillars due to its safe and green mining characteristics. However, traditional cemented paste backfill mining has some shortcomings, such as poor adaptability to geological structure, leakage of paste during filling, imperfect roof-contact in partially backfilled areas, and insufficient roof strata support before the backfill reaches its design strength. This paper presents the results of a case study where L-shaped interval cemented paste backfill technology has been safely used to mine an isolated coal panel beneath existing surface structures. This backfilling method has the advantages of preventing paste leakage, improving the backfilled ratio, reducing surface subsidence, and strongly adapting to geological structure. During this field application, the setting pressure of the backfill shield reached 20 MPa, the compressive strength of the backfilling body reached 2.0 MPa, and the backfilled ratio reached 93.7%. Observational ground monitoring showed that roof-to-floor convergence in adjacent roadways ranged from 132 to 167 mm. No obvious fractures or separations in the overlying strata were observed by a borescope. The maximum surface subsidence was 342 mm, the subsidence factor was 0.136, and the damage to surface buildings was within Grade I (slight damage). This case study clearly demonstrates that the L-shaped interval cemented paste backfill method can be safely used to mine the isolated coal panel beneath surface buildings.

Jul 1, 2023

By Thomas J. Neil, O&apos

Mine land reclamation is a comparatively new science-Although some mining companies point with pride to reclamation efforts of 20 to 30 years ago these were the exception rather than the rule. In the last ten years the skyrocket of environmental awareness has been awesome to behold. Future shock gripped mine operators everywhere as they struggled to cope with rapidly changing and escalating demands. The initial result was that two divergent points of view became dominant. Environmentalists said, "Put it back the way it was," and the miners responded, "Let's grow some weeds and hide it." These views are not surprising as they represent rather obvious alternative responses, albeit at opposite ends of the decision spectrum. The former case has prevailed more often than the latter, as most state and federal legislation -- both proposed and passed -- has required drastic alteration of the post-mining landscape so that evidence of prior mining is largely obliterated. An exception to this has been in porphyry copper country where the infrequent abandonment of mines has given emphasis to the second philosophy -establishing vegetative cover on mine waste materials. Now, it should come as no revelation to most mining people that both of these approaches to mine reclamation suffer from serious drawbacks when applied to open pit copper mines. First, whereas waste dumps and tailings dams can be vegetated with some aesthetic benefit, the massive presence of copper mining operations remains very prominent. It is difficult to conceal an open pit copper mine. Second, returning open pit copper mines lands to their original topography and productivity is simply not a reasonable alternative.

Jan 1, 1976

By P. K. Muduli

The number and the type of trucks and shovels are two important factors in determining the optimal design parameters of an open-pit mining system. Characteristics of trucks' arrival and service-time distributions determine the performance measures of a truck-shovel system when it is modeled as a closed queuing network. In all of the previous analytical queuing studies of truck-shovel systems, trucks are assumed to be identical with respect to their arrival and service-time distributions. This assumption, although desirable for reducing computational difficulties, causes either underestimation or overestimation of the performance measures depending on the number and type of equipment used in the model. The relative error in performance measures could be significant when the number of different types of trucks and shovels is large. In this paper an analytical method is proposed to model the truck-shovel system as a multiple-chain closed queuing network. This approach would provide the capability of estimating system performance measures for planning purposes when the truck fleet is not necessarily composed of identical trucks. An example of truck-shovel systems is discussed to show how the incorporation of different types of trucks does affect performance measures.

Jan 1, 1996

By David A. Milligan, William Cobb

2.1 INTRODUCTION This chapter provides the reader with a sense of how a heap leach project may make an orderly, and hopefully non-traumatic, transition from discovery or acquisition to project construction. In making this transition a project can pass through several project development phases (i.e. ore definition and delineation, conceptual engineering, detailed engineering, and ultimately on to project construction and operation). "Go" or "no go" decisions may occur at any point in each of these phases. The transition from ore definition to detailed engineering should be accomplished via a well thought out program of interdisciplinary studies and an integrated, interdisciplinary project team. This chapter also describes, in general terms, a "roadmap" approach to the project evaluation process that must occur as project planning and development progress. It is the experience of the authors, as well as a myriad of companies who have been through the heap leach project development process, that a systematic approach will save many headaches, and many dollars. In fact, it is safe to say that a project with no formalized system of "objectives setting" and "milestone charting" may well flounder along the way, even if an economic ore body exists. Many papers and technical articles have been written about various aspects of mineral resource appraisal, economic evaluation, and mine development. Most of these invoke the same general philosophy of a systematic approach to project evaluation and development, although methods cited for attaining goals are quite variable. This is undoubtedly appropriate, given the fact that there is great variation in approach to project development (e.g., climatic considerations, ore body size and physical ore characteristics, permitting constraints, etc.). For the purposes of this chapter, two primary sources of information have been used to highlight the "road map" approach previously alluded to. These sources are cited throughout the text as Mackenzie (1980) and Snow and Michel s (1986). A brief summary of each of these sources is provided below: Brian GJ. Mackenzie of Queens University (Mackenzie, 1980) has developed a wealth of information concerning project development topics. Much of this information is synthesized in his notes for a short course entitled : "Mineral Exploration Planning and Economic

Jan 1, 1988

By R. D. Beard

Puerto Rico lies within the remnants of a deformed Cretaceous island arc system in the northeastern Caribbean. The Island can be divided into three broad geologic provinces: the Central Volcanic-Plutonic Province (Lower Cretaceous to middle Eocene), and the Northern and Southern Limestone Provinces (early Oligocene to middle Miocene). Known precious metal deposits are generally small and occur in veins and shear zones within Lower and Upper Cretaceous volcanic and plutonic rocks. Some Tertiary igneous rocks are also mineralized. Selected indications of disseminated lithology-controlled mineralization could represent larger deposits. Associated metals in some deposits include copper, zinc, and lead. At present, tax policies, population density, political outlook, and lack of proven significant precious metal deposits discourage the establishment of a metal mining industry.

Jan 1, 1993

By Anil Kumar

In underground mine production units that employ discrete-vehicle face haulage, feeders are used in the belt network so that vehicles can unload rapidly without transmitting to the conveyor network the high material flow rates that result from rapid unloading. They prevent production bottlenecks at the face, while reducing capacity requirements for downstream materials handling equipment. Similarly, surge bins may be installed at intermediate locations in the network to smooth flows from a number of upstream sources, thereby reducing downstream belt capacity requirements. This paper introduces new stochastic process models to temporally describe loading patterns from unit operations and techniques for computing the probability of various fill levels for the feeder or surge bin. These results may be used to analyze the effect of alternative bin or feeder capacities and discharge rates on the performance and costs of the materials handling system.

Jan 1, 1994

By G. T. Homce

Most electric motor predictive maintenance methods have drawbacks that limit their effectiveness in the mining environment. The U.S. Bureau of Mines is developing an alternative approach to detect winding insulation breakdown in advance of complete motor failure. In order to evaluate the analysis algorithms necessary for this approach, the USBM has designed and installed a system to monitor 120 electric motors in a coal preparation plant. The computer-based experimental system continuously gathers, stores, and analyzes electrical parameters for each motor. The results are then correlated to data from conventional motor-maintenance methods and in-service failures to determine if the analysis algorithms can detect signs of insulation deterioration and impending failure. This paper describes system design and implementation. At this writing, however, installation is still underway, and field data analysis results are not yet available.

Jan 1, 1994

By Steven J. Schatzel, Mark M. Mazzella, Robert A. Kimutis, VASU GANGRADE, James D. Addis, Marcia L. Harris, Mayley Guitard

Researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated the impact of potential shale gas well breaches and subsequent gas inflow on selected mine ventilation systems of operating longwall panels using a 1:30 scaled Longwall Instrumented Aerodynamic Model (LIAM) and Sulfur hexafluoride (SF6) as a tracer gas. A series of tests were performed at 340, 400, and 500 cfm inflow levels utilizing different mine ventilation scenarios. Results suggest that the breached gas can be diluted to meet statutory levels when the longwall panel is adequately ventilated. The results enhance the understanding of the gas inflow and mine ventilation system interaction and provide critical information to the industry and regulatory agencies for improving miners’ safety.

Feb 1, 2024

By A. Heriba

Cyanide is highly toxic to humans and other organisms. Concentrations of RCN as low as 0.05 ppm can be lethal to fish (Scott and Ingle', 1981). In wet climates and in colder climates where natural degradation is slow, it is becoming mandatory to destroy cyanides in effluents before they can be discharged. The disposal of spent gold ore as tailings from cyanide heap leach processing facilities is a matter of concern to the public, the mining industry, and regulatory agencies. South Dakota mining laws and regulations require that spent ore be neutralized to a suitable level with respect to cyanide before disposal (Durkin, 1990). To safeguard the environment and protect ground-water and surface-water supplies adequately, a reliable test is needed to determine the amount of cyanide in the solid spent ore.

Jan 1, 1993