Search Documents

By John P. Anderle

A tectonically disturbed sequence of Mississippian age evaporites expressing a 5 milligal negative gravity anomaly near Sussex in southeastern New Brunswick, Canada, was investigated by a program of drilling, geologic and geophysical work over the past 27 months. Seventeen of twenty-one drill holes have penetrated 10 to 140 feet of potash mineralization in a salt sequence underlying 2 000 to 3 000 feet of arenaceous, conformable red beds, also of Mississippian age. Bromine and borate studies, lithological characteristics and geophysics, have facilitated improved understanding of the salt structure. The salt sequence has been affected by f1owage which has resulted in both major and minor folding. In the more disturbed areas, the potash interval was extensively subterraneally eroded at the upper anhydrite-salt contact.

Jan 1, 1978

By K. E. Hjelmstad, W. H. Pomroy

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage. Recent research by the US Bureau of Mines has established the feasibility of ultralow frequency electromagnetic signaling for underground mine fire warning. Infield testing completed thus far at five mines, signals of from 630 Hz to 2000 Hz were transmitted through rock up to distances of 1645 m (5400 ft) to a pencil-sized ferrite-core receiving antenna and intrinsically safe receiver circuit. Theoretical analysis indicates a capability to transmit effectively for distances in excess of the maximum depths of most American mines, which is about 900 to 1000 m (2950 to 3280 ft) . The prototype system uses off-the-shelf components and state-of-the-art technology to ensure high reliability and low cost. This technology would enable simultaneous and instantaneous warning of all underground personnel, thereby in- creasing the likelihood of successfully evacuating a mine during a disaster. This report discusses the theoretical basis for through-the-rock ultralow frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 1991

By W. G. Miller

A series of computer programs for the analysis and mapping of coal-related data has been developed at the Illinois State Geological Survey; these programs, known collectively as the Coal Data System, represent the latest achievements in computer processing of geologic data at the Survey. Building upon programs previously developed in the Survey's Computer Services Unit, they expand the scope of the computerized data base that the Survey has been using for analyzing coal-related data. The System was partially developed during a joint study by the Illinois State Water Survey and the Geological Survey entitled, ?Coal and Water Resources for Coal Conversion in Illinois.? 2 In that study the available coal reserves more than 42 inches thick in the two principal coal seams throughout the state were mapped. The System was used to calculate the coal reserves and to report the average number of tons of coal in place per square mile in each township (Figures 1 and 2). It also produced maps of the coal features of sufficient quality to be printed on material that was scribed as master copy for the printing of full-color 1:500,000 scale maps (see Figures 3 and 4).

Jan 1, 1975

By John C. Schneider

In the mid 60's Prochem & Hydrochem Development, it's research division, developed the high efficiency Maxflo impeller. Since the Maxflo impeller had a design that had proven to be very efficient in gas-liquid-solid contacting, it was a natural extension to apply this design to flotation & the research commenced in the mid 80's. An opportunity to test the energy savings occurred at Dickenson Mines in 1987, & comparative results with existing conventional flotation cells showed a marked increase in capacity, grade & recovery with 25% less power applied. This r success was followed by the installation of the fist agitated Flotation Colunm (5ft. dia. x 25ft. tall). As a result of the Dickenson success, Hydrochem started a comprehensive 2-part research program in 1988. At Randol Gold Forum 1988 a paper by Hydrochem was pre

Jan 1, 2000

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, Aditya Rana, M. M. Singh

The paper presents an innovative directional controlled blasting (DCB) technique for excavating unstable slopes along the Konkan railway in India without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw were developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3, irrespective of the actual free face, was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle was changed from 80–82 to 45–47 degrees, and possible wedge, planar and toppling failures were eliminated. No incident of rockfall and slope failure along these slopes has been observed after the stabilization.

By S. Mathur

The southern Florida phosphate deposits that will be mined in the future contain significant amounts of dolomite. Because high MgO levels are undesirable in phosphoric acid production, several flotation schemes for the removal of the dolomite have been attempted. Alternatively, selective flocculation has been suggested as a potential process. A high MgO rock was simulated with a 30:10:60 mixture of apatite, dolomite and silica, respectively. Single mineral selectivity was observed in the apatite-silica and dolomite- silica systems using Polyacrylic acid (PAA) and Poly(ethylene oxide) (PEO) flocculants, respectively. However, no single mineral selectivity was observed in the apatite-dolomite system using PEO. Heteroflocculation, suspected to be the major reason for the loss of selectivity, was minimized by the addition of a site blocking agent (SBA), consisting of a lower- molecular-weight fraction of PEO. Process parameters such as size reduction schemes, flocculant/SBA dosage and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed-mineral tests was also achieved in the ternary mixed-mineral system, namely, the apatite-dolomite-silica system. In this report, surface chemical characterization of the samples and their flocculation behavior are discussed.

Jan 1, 1995

By Glenn Mongillo

Discrete Element Method (DEM) software has been successfully used to simulate various machine/soil interactions and provide insight for industries such as mining and bulk material processing. This paper will investigate typical calibration techniques used in particle models for DEM simulation and physical calibration experiments with soft ground TBM cutting tools to incorporate parameters such as tool drag forces that contribute to required TBM torque. With a well calibrated DEM model, it is expected that TBM simulation results will be more meaningful and provide better insight into TBM performance, power requirements, cutting tool placement, and overall cutter head design.

Jun 13, 2021

By HONGWEI YANG, Lili Zhang

Copper slag is mainly used in cutting tools, abrasives, asphalt pavement, road construction, and in the production of concrete as an alternative to sand and cement [1]. As a renewable resource, only about 15-20 percent of the slag is used for these applications, and the dumping or disposal of surplus unused slag results in waste of a certain amount of usable metal in the feedstock [2]. In this work, the oxidation behavior of copper smelting slag under nonisothermal condition is studied using data obtained by the thermogravimetric (TG) method, and the kinetics parameters and reaction mechanism of oxidation are determined. It provides a theoretical basis for the comprehensive recovery of iron resources in slag and the selection of reasonable slag-making conditions.

Oct 1, 2022

By Jerry W. Danni, John E. Hardaway

Corporations today must comply with an ever growing number of complex and increasingly stringent environmental laws and regulations. An environmental audit program is an effective means in which to uniformly and systematically assess compliance, and to assure management that environmental liabilities are being minimized. This paper describes the design and implementation of Homestake Mining Company's environmental audit program, which has as its primary focus the objective verification of compliance with external requirements and internal good management practices. Major elements of the audit program discussed in the paper include: pre-audit preparation; on-site audit activities; and the post-audit report.

Jan 1, 1992

By M. Moss Stanley, Ronald P. Klepper

The objective of this chapter is to provide data that will assist in the selection and sizing of equipment utilized in the filtration method of separating solids from liquids. It should be recognized at the outset that in some situations more than one option may be available to achieve the target desired. In some cases purely technical objectives may be sacrificed because of cost considerations, design factors or other elements in order to satisfy optimization within the flowsheet and/or to provide bottom line results. Before considering available options, and prior to the next step of sizing out the selection, the operating criteria should be set down. The test work to develop selection and sizing data will be based on this data and the final products desired. This will help to establish initial parameters. A. GENERAL DATA 1. Material to be filtered: a. Solids b. Mother liquor 2. Feed rate of slurry in GPM 3. Density of slurry: Sp. Gr. Solids 4. Slurry: Temp. pH Viscosity 5. Source and method of feed 6. Valuable product: Solids Filtrate Both 7. Details on: Volatility Toxicity Stability 8. If flocculant is indicated, what has been used? 9. Describe product: (i.e., fibrous, cor 10. rosive, abrasive, inflammable, explosive, pasty, 11. Does product alter or require special environment during transport? 12. What type of filter media has been used successfully? 13. Is there any objection to use of a filter aid? If not, is there any preference? B. SOLIDS DATA 1. Sp. Gr. Bulk density 2. Screen analysis 3. Desired percentage moisture in cake 4. Solubility (state conditions): In mother liquor In wash water 5. Description of cake: (i.e., amorphous, fibrous, crystalline, colloidal, gran¬ular, thixotropic, 6. Special requirements for moisture de¬termination? 7. Can solids be compressed during dewatering? 8. Proposed product handling 9. Subsequent thermal drying or other pro¬cedure C. FILTRATE 1. Is separation of wash water and mother liquor desirable?

Jan 1, 1986

By G. W. Riley, D. E. Pickett

HINDERED SETTLING CONCENTRATION In the free settling of mineral particles in a liquid, the falling particles are at a distance from each other so that no particle is affected by its neighbor. In hindered settling, the concentration of particles is sufficiently high so that each particle is affected by its proximity to other particles in the suspension. Richards and Locke86 have described the hindered settling phenomenon as the condition “.. where particles of mixed sizes, shapes and densities in a crowded mass, yet free to move along themselves, are sorted in a rising current of water, the velocity of which is much less than the free-falling velocity of the particles but yet fast enough so the particles are in motion." This is the condition normally encountered in mineral con¬centration processes. The well known Newton equation for free settling of coarse (ap proximately +10-mesh, 1/16-in. or -- 2000-µm) spherical particles is:87 where v," is free settling velocity, cm/sec; p' is density of the fluid; p is density of the particle, g/cm3; d is particle diameter, cm; g is acceleration due to gravity, cm/sec2; and Q is coefficient of resistance, dimensionless, ~0.4. For the settling of fine spheres in water (approximately 150 mesh or 100 µm) the equation of Stokes pertains:87 where µ is viscosity of the fluid in poises and the other symbols have the same meaning as those in Eq. 1. For particles whose size lies between about 10 mesh (--2000 µm) and 150 mesh (100 µm), their settling velocity can be determined from experimental data. These data are available in convenient form in the text by Taggart88 based on the original work of Richards. Alternatively, a Reynolds number-coefficient of resistance plot may be used to determine the settling rate of such particles.87 The settling rate of spherical particles under hindered settling conditions can also be calculated from Eqs. I and 2 by replacing p', the density of the fluid, by p" the apparent density of the suspen¬sion. The concentration of particles in the fluid thus imparts an appar¬ent density to the composite fluid or suspension greater than that of the liquid alone, resulting in a buoyant effect on the larger particles. Particle shape affects the settling rate of both coarse and fine particles. The general effect is to reduce their settling velocities and the effect is greater for coarse particles and for those settling under hindered settling conditions than for fine particles or free settling ones. For two particles of differing densities but settling at the same velocity under Newtonian conditions, the ratio of their diameters from Eq. 1, called the free settling ratio is: where L signifies the lighter particle and H, the heavier particle. Under Stokesian conditions the exponent would be 0.5. For hindered settling conditions the fluid density p' is replaced by the apparent density of the suspension, p", to obtain a generalized equation for the hindered settling ratio: assuming both particles settle in approximately the same regime. The free settling ratio as given by Eq. 3 has been called by Taggart88 the "concentration criterion" and is used to predict the effectiveness of any gravity concentration process (see Introduction to this section). Based on Eqs. 3 and 4, if two particles of densities pH and p,, settle at the same velocity, the diameter of the lighter particle will be larger than that of the heavier particle. For example, in the case of galena (pH = 7.5) and quartz (pL = 2.65) settling in water (p =1.0) under free settling, Newtonian conditions 3.9. Thus, a quartz particle nearly four times as large as a galena particle will settle at the same velocity. Any quartz particle just slightly less than four times the diameter of the largest galena particle may be separated from it. Under hindered settling, Newtonian condi¬tions in a suspension where p" = 1.65, dL/dH = 5.85 or any quartz particle just slightly less than about six times the largest galena particle may be separated from it. Reference to Eq. 4 indicates that a superior separation between two minerals of differing densities is favored by: (1) coarse particles settling under Newtonian conditions, (2) a large difference in (pa - PL), and (3) separation under hindered settling conditions where p" is high. Of course, there are practical limits to increasing p" excessively because at very high percent solids suspen¬sion fluidity would be lost and the hindered settling separation process defeated. Examples of hindered settling separators are the Dorrco-Fahren¬wald sizer,89 the Rheolaveur box 90 the Spitzkasten,89 and the Willoughby washer.91 These devices make a mineral separation on the basis of both specific gravity and size and all of them are essentially obsolete except for the Dorrco-Fahrenwald sizer and similar devices which still find application for the removal of coarse particles from a much finer particle assemblage and for preconcentration ahead of shaking tables. However, nearly all gravity concentration processes (jigs, tables, flowing film concentrators, heavy media separators) and many sizing devices (sizing classifiers, clarifiers, thickeners, hydrosepa¬rators) make use of the hindered settling phenomenon during the separation of particles. JIGGING Introduction In jigging, a mixture of ore particles, supported on a perforated plate or screen in a layer or "bed" with a depth many times the thickness of the largest particle, is subjected to an alternating rising and falling (pulsating) flow of fluid with the objective of causing all

Jan 1, 1985

By Jeff W. Butwell

Mill flotation tailings impounded at the Gooseberry Mine site between 1976 and 1984 were determined to be an economic source of gold and silver recoverable by standard heap leach technology in conjunction with feed agglomeration. Metal recovery at 85 percent Au, 75 percent Ag is attained on properly agglomerated (pelletized) tailings which average 85 percent -75 micron. Because the impounded tailings averaged over 18 percent moisture (32 percent moisture maximum at depth) in place behind the storage dam, the mining method, mixing and agglomeration technique, and materials handling practice were major considerations in making this operation a financial success.

Jan 1, 1990

By Joseph W. Siefke

The Kramer borate deposit is located in the western Mojave Desert at Boron, California, about 100 miles northeast of Los Angeles (Figure 1). The deposit derives its name from the district in which it lies. Borax (Na2 B407.10H2O) is being mined from the Boron open pit to serve a major portion of the United States and world borate markets. This paper deals primarily with those geologic factors which affect slope stability in the overburden at the Boron open pit. Discussion includes slope failure history, slope monitoring techniques and the results of a dipmeter survey of overburden structure. Open pit mining was begun at Boron in 1957. The initial pit was successfully excavated at the recommended 1.5:1 (horizontal to vertical) slope in the overburden. During pit expansion in 1962, excavation of the overburden exposed beds dipping into the pit at +15 degrees and numerous high angle fractures associated with two intersecting fracture systems, the West Jenifer and Portal fault zones. Ensuing south and east wall failures indicated the need for more structural information in the arkose to establish better wall design criteria. Barnard and Kistler (1963) recognized that the many facies changes, faults and other variables in the Boron overburden make it extremely difficult to reduce prediction of slides to a simple arithmetical formula. Despite the difficulties and uncertain¬ties, special programs such as surface resistivity, refraction seismic and core drilling were conducted in an attempt to predict slope stability conditions and to gather geologic information. These early efforts while helpful, did not provide the necessary details of bedding orientations and fault locations which are of paramount importance in our slope stability program. A dipmeter survey in 1974 successfully measured these variables and data from that survey are instrumental in the design of slopes currently being excavated.

Jan 1, 1976

By R. D. Cook, J. L. Johnson

"Measuring mud bed level in a sedimentation device is an important control variable. Methods used to date for this purpose have had limited success providing continuous, consistent measurements at a reasonable price. This paper describes a new instrument for detecting the mud bed / liquor interface as well as bed density profiles. The state of the bed is measured directly with sensors located in the thickener. Data from bench-scale and full-scale tests show that the bed level is well defined and easily detected. In addition, full-scale testing revealed unprecedented information about thickener beds. Variation in bed density gave new insight into thickener bed dynamics, providing design and control opportunities never before possible. This novel instrument can significantly improve thickener control by providing reliable and consistent bed level measurements. It is also capable of measuring bed density profiles that can potentially identify significant operating problems early enough to take corrective action before experiencing costly shut downs. INTRODUCTION Numerous studies and papers have been devoted to the subject of thickener design and operation to achieve specified throughput and discharge densities. Mathematical models have been developed that present methods for sizing thickeners and predicting performance under varying process conditions. The compression effect of deeper beds on dewatering performance is a recognized phenomenon (Wilhelm and Naide 1981). This is one variable of many that are inter-related and influence thickener performance. For example in the steady-state, continuous operation of a thickener, if the solids feed rate increases and the bed level remains the same, the underflow discharge rate must increase with the result of solids concentration being lower. The interactions of these parameters are at the heart of thickener models. One such model (Burger and Narvaez 2007), predicts solids concentration profiles increasing downward and discontinuities between settling zones. This model uses sediment height (bed level) as a parameter that influences capacity calculations to achieve the specified solids concentration of the underflow. Knowing the bed depth is critical to maintaining stable thickener operation. Implicit in these modeling strategies are some basic assumptions such as homogeneous distribution of solids in the different settling zones, plug flow of solids through the settling zones and steady state operation of the thickener. The accuracy of these assumptions has not been verified because there has been little visibility inside the bed of full size operating thickeners. Testing of the instrument presented in this paper demonstrates that it provides a degree of visibility of the dynamics in a thickener not previously possible and indicates that the basic assumptions of the modeling strategies may not be completely accurate."

Jan 1, 2015

By D. Hulse

"The science of “optimal economic pit design” has been highly refined in the last decades. Even with the proliferation of optimizing and heuristic algorithms exploiting ever faster computers, the most common input is a single block model and a single set of cost assumptions, each of which is an estimate and prone to errors. An analysis of price assumptions produces a suite of nested economic shells, each with its own quantities of ore, waste, grade, and profit, but due to irregularities in the mineralized body, the growth of these shells can be erratic. To control the impact of the errors of the model and cost assumptions when choosing the pit shell for design, graphs of pit shells characteristics, such as stripping ratio, cost per unit of product and profit/ton, can be analyzed to consider points with higher stability, or robust pits. Selection of robust shells for a pit limit and for push backs can help to understand the impact to profit and risk. The robust shells also guide the preferred solution sets for final pit and cutoff optimization. INTRODUCTION “An open pit mining operation can be viewed as a process by which the open surface of a mine is continuously deformed. The planning of a mining program involves the design of the final shape of this open surface.” Optimum Design of Open-Pit Mines, Lerchs, H. and Grossmann, I. Transactions C.I.M. Volume LXVIII 1965. Traditionally an analysis of economic pit shells and sensitivity was performed by varying the input metal price. This was done with both floating cone algorithms as well as early versions of the Lerchs-Grossmann (L-G) algorithm. This gave an indication of the pit sensitivity to price but since other variables also change, some with metal price (perhaps steel and equipment), and some independently (fuel and tires) the understanding of these different pits was restricted. In addition, a run of the program could take hours, making a detailed analysis of small changes unwieldy. The L-G algorithm was programmed by a variety of people and sold as part of commercial mining packages, however it was first and most successfully commercialized by Jeff Whittle in 1984. When Whittle’s 3-D™ was expanded to 4-D the parameterization of the economic inputs was considered and the ability to run a suite of “pit shells” became automatic. The competing NPV Scheduler™ program sold by DataMine™ offers similar pit shell analysis capabilities."

Jan 1, 2018

By J. Franko, M. S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium separation circuits. In this study, the performance of a continuous, laboratory wet-drum magnetic separator was evaluated both with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration and nonmagnetic material. The results indicate that, under certain conditions, the purity of the magnetic material increased after ultrasonic treatment. Key words: Ultrasonics, Wet-drum magnetic separation, Iron ore

Jan 1, 2003

By James J. Brady, James S. Lewis, Robert B. Gordon, Jimmy W. Honeycutt

INTRODUCTION Tunnel construction has always been an extremely high risk form of contracting primarily due to the inaccessability of information concerning the ground conditions to be encountered during excavation. We certainly make every effort to overcome this problem through borings, geological research, site visits, etc.; but at best owners, engineers and contractors alike are only able to interpolate a relatively small amount of factual data from isolated sections of the project into a forecast of ground conditions for the entire project. In essence this becomes an "educated guessing game" with risk to reward ratios (and subsequently the bid price) in direct relationship to the contractor's confidence in the quality of the guess. In many instances it is economically or physically infeasible to obtain information and of course the total picture is never known until the project is complete. This problem effects the contract format as well as price. The contractor's ability to handle unforseen problems on the project become extremely important as to the project's overall success. The following pages contain an actual case history of a project which affords an excellent example of the entire spectrum of situations resulting from tunnel construction in difficult ground conditions.

Jan 1, 1983

By Simon Wright, Roland Heersink

In the past, the center of most companies' e-initiatives has been on reduction of indirect costs, such as selling and procurement. Recently, e-commerce has moved its attention from back-office functions into manufacturing, in order to significantly reduce direct operating costs. This paper describes many of the Web-Powered Manufacturing initiatives being employed across various industries, and relates them to similar opportunities being started within the mining and mineral-processing sector. The following opportunities are enabled by Web-Powered Manufacturing: • Collaboration with outside experts to extend their pool of resources • Management of remote and distributed operations • Tie-in of small operations to a larger operation • Monitoring a position in a JV operated by a partner • Managing a plant located in someone else's facility • Having a chemical supplier manage his inventory in a customer's tanks • Having an equipment supplier remotely troubleshoot his equipment installed in a customer's site • Having an additive supplier provide remote pro-active. guidance in optimization of a customer's operation • Having software suppliers take responsibility for the results of their applications • Outsourcing software and systems support by providing remote access Details of one of these opportunities are described in this article, and the benefits captured using this approach and the technologies necessary to make them a reality are emphasized.

Jan 1, 2002

By R. D. Schmidt, S. E. Follin

Introduction Mineral recovery from an in situ leaching operation is determined by the often complex interaction of hydrology, mass transport, and chemical kinetics. The operating conditions of many pilot and production scale uranium leaching operations involve heterogeneities in aquifer permeability. Differences in permeability may be naturally occurring, the result of differences in main size or cementation, or they may be induced by leaching activity. Variations in permeability directly affect the fluid flow streamline pattern, fluid flux, and so also leaching geochemistry and uranium recovery. An in situ leaching hydrology model (ISL) and a mass transport-oxidation rate model (ISLGC) have been developed for use in making site specific predictions of the leachability and productive potential of heterogeneous ore deposits, and for the optimal design of leachant injection and recovery operations. The two models are linked by output and input requirements. The ISL hydrology model generates a leachant flow streamline pattern between injection and recovery points in a flow domain incorporating regions of arbitrary permeability. The ISLGC transport model describes the changing solution concentrations of uranium and oxygen and the changing mineral concentrations of uranium and pyrite resulting from convection, longitudinal dispersion, and oxidation reactions. ISL hydrology model Basic equations The differential equation for steady-state two- dimensional flow in an isotropic porous medium is

Jan 1, 1988

By Peter Amelunxen, Brandon Akerstrom

Since its introduction 40 years ago, the compartmental model of flotation has been used to predict the performance of mechanical flotation cells. However, it has found limited success for modeling dual-chamber machines and, as a result, engineers have adopted empirical correction factors usually derived from field audits of industrial cells to predict the performance of dual-chamber flotation cells. This paper introduces an extension of the compartmental model that applies to both single- and dual-chamber cells. The model is tested against pilot test work performed at Capstone’s Pinto Valley concentrator, and then used to evaluate the key operating and design parameters of dual chamber flotation cells. The results suggest that the design of the mixing chamber — for example, whether it is pneumatic or mechanically agitated — is not a significant contributor to overall machine performance. The work also suggests that the highest recoveries are achieved when the froth recovery is high, and longer separation chamber residence times and/or higher internal circulating loads are only beneficial when the froth recovery is low. Lastly, the results show that the single most important driver of the machine performance is the froth recovery of the separation chamber.

Mar 1, 2025