Search Documents

By William G. Pariseau

The purpose of this paper is to present a design procedure for the quantitative estimation of support load requirements in underground mines. Emphasis is upon the basic features of support behavior common to a large variety of support systems-bolts, timber sets, stope fill, steel arches, concrete liners and so forth. A strong reliance is placed upon fundamental principles and modern computing techniques for their quantitative implementation. Example problems illustrate the approach. Where artificial support is required, the ground in the vicinity of the face usually stands unsupported long enough for the support to be installed. At the time of installation, the load transferred to the support from the adjacent rock is essentially zero, although in some cases there may be an initial set load, for example, from timber blocking. With the passage of time and advance of the face, ground motion loads the supports. If the support system is properly designed, then the additional loading poses no threat to the safety and productivity of operations. If not, then difficulties may arise including high maintenance costs, hazardous work conditions and reduced productivity. Of course, over-design can be equally wasteful. Quantitative estimation of support loads is therefore essential to overall efficiency in mining.

Jan 1, 1975

By D. W. Olson

Estimated world production of natural and synthetic industrial diamond was about 630 million carats in 2004. Natural industrial diamond deposits have been found in more than 35 countries, and synthetic industrial diamond is produced in at least 10 countries. About 80 percent of the global output was produced in Ireland, Japan, Russia, South Africa and the United States. Russia and the United States are the world’s leading producers of synthetic industrial diamond. In 2004, the two U.S. synthetic producers, one in Pennsylvania and the other in Ohio, had an estimated output of 250million carats. Also in 2004, nine U.S. firms manufactured polycrystalline diamond (PCD) from synthetic diamond grit and powder.

Jan 1, 2005

By Norbert Steiner, Roy Norcross

For the desulfurization of weak SO2 gas streams, Degussa developed a process using dilute H2SO4 solution containing H2O2 instead of conventional gas scrubbing with all solid absorbent medium (limestone, MgO). The process is based on fast reaction of H2O2 with SO2 yielding H2SO4 up to 70% strength, depending on off-gas tem­perature. Compared to the conventional systems with typically < 95% efficiency, independent on the raw gas SO2 concentra­tion, residual SO2 concentrations of less than 20 mg!Nm3 can be easily achieved, corresponding to nearly 100% removal. These features render the H2O2 process a very attractive, low capital cost technology to retrofit existing conventional desulfurization plants.

Jan 1, 1996

By C. K. Blair, V. J. Hucka, E. P. Kimball

In central Utah, a coal mining operation is taking place under an 0.5-m (20-in.) pressurized natural gas pipeline. The room-and-pillar method with pillar extraction is being used to extract the coal from the seams. The pillars beneath the pipeline will not be extracted; however, there is a possibility that some subsidence may occur due to pillar failure. To assess possible damages on the pipeline, an attempt has been made to predict subsidence in the area where pillars may collapse. The resultant values of subsidence strain and slope have been used to determine the magnitude of strain, stress, and shear induced in the pipeline. Also, a network of survey points has been installed along the pipeline to detect ground move¬ment that would indicate excessive subsidence.

Jan 1, 1987

By Kotaro Ohga, Gota DEGUCHI, Kiyoshi HGUCHI

The situation of Japanes coal mine is in the severe enviroment, because the policy on coal mining has changed. Every year one or two coal mines will be foced to close. To continue the production of coal, we have to reduce the cost of production. Therefore, the mining by longwall method which is more than 250m was attempted at Taiheiyou Coal Mine to reduce the cost and this mining method have had successful results. To get successful results by this mining method, the controlling and prediction of gas emission from the longwall panel will be most important things. In this paper, the comparison of the predicted gas emission from the mining panel based on the measured gas content by using new device with the observed results is described.

Jan 1, 1993

By John T. Gormley, Pressley L. Campbell, Harry L. Crouse

INTRODUCTION This paper summarizes an investigation conducted to determine the relationship, if any, between reported occurrences of abnormal levels of carbon dioxide (C02) gas and the construction of a 2.44meter diameter main sewer tunnel under South Eighty-Fourth Street, West Allis, Milwaukee, Wisconsin. Specific objectives of the study were to determine: (1) the sources of C02, (2) the significance of each C02 source, (3) how C02 could move to areas where it was reported to occur in abnormal concentrations, and (4) what actions could be implemented to eliminate elevated C02 levels associated with the tunneling operation. To accomplish study objectives, expertise from several scientific and engineering disciplines was required including chemistry, geochemistry, microbiology, hydraulics, and hydrology. Pertinent documents were reviewed and field data pertaining to each aspect of the study were collected as required and examined to evaluate existing conditions. Background On or about February 1, 1971, gas with a composition different from normal atmospheric air was reported to enter basements and wells of residences in the vicinity of South Eighty-Fourth Street, West Allis, Wisconsin. Examination of the gas composition revealed that it possessed an elevated concentration of C02 and a depleted concentration of oxygen (02). Public health officials who investigated the appearance of the objectionable gas concluded within reasonable certainty that the elevated C02 concentrations were associated with the tunnel construction under Eighty-Fourth Street.

Jan 1, 1979

By Katherine Hynard, Colin Eustace

Suboptimal decisions introduced during the mine planning process are generally a consequence of both a myopic view of planning objectives as well as time and resources available to convert longer-term plans into execution plans. Erosion of strategic mine plan value in conversion to execution plans is likely to amount to billions of dollars each year. When integrated with operations data feeds, simulation and optimization tools can be used to preserve the value in the strategic mine plan. Optimization models are capable of both automating production of execution plans and improving performance. This reduces the manual burden of revising plans while improving alignment with long-term production objectives. Simulation models can also support the process of developing effective execution plans by providing forward visibility of mine operations performance. They can also be used to test the robustness of optimized execution plans and response to operational variability and disturbances.

May 1, 2025

By Ditend Tesh, Godfrey Dzinomwa, Harmony K. Musiyarira

Namibia is known as water stressed country with a limited amount of fresh water. Therefore, the use of water is an important topic in the country’s development agenda. Water is a shared and finite resource, with high social, cultural, environmental and economic value. However, freshwater resources are under pressure from ore processing, industrialization, urbanization and the demands of a growing population. In Namibia, ore processing, coupled with the anticipated increase in water demand for human consumption and other uses, has created significant stress on the limited water resources of the country. This is critical in the mining industry as water remains typically the prime environmental medium (besides air) that is affected by mining activities. This study sought to investigate the strides made in water management in mining, especially in environmentally sensitive areas of Namibia. Most mining companies operate next or alongside farms, national parks and fishing areas. The overall objective of this research was to highlight the current practices in Namibia’s mineral industry operating in environmentally sensitive areas especially in areas where uranium is being mined and processed. The methodology consisted of comprehensive literature review, field visits to the case study areas, and comparative studies with best practices. This study shows that over a ten-year period, freshwater consumption was reduced by over 55% per tonne of milled ore in uranium mines, resulting in substantive financial savings as well as the delay in water augmentation through desalination. The strategies employed by the Namibian companies involve inclusive stakeholders’ engagement, recycling and reuse, and the minimization of water losses. The realization that the water challenge cannot be solved by any one party acting alone has been fundamental in ensuring environmental compliance within the mining industry in Namibia. Namibia’s industrial leaders have increasingly recognized that reducing the water footprint of mining activities must be one of the key performance indicators for management. The major finding of this study was that Namibia with its unique ecosystems, mineral reserves, and emerging industries can harness a wide range of resources both to improve the welfare of its citizens and to protect the integrity of its environment.

Jan 1, 2017

By Richard Keith Corbin

INTRODUCTION With the world media full of predictions that the price of gold will quadruple in three years (Maybury, R.J., 1988), and with financial forecasters and strategists touting opportunities to make 400% in gold (Skousen, M., 1988), explorationists and entrepreneurs are scurrying to find enough gold to feed the global gold fever created. At the same time, gold deposits in the United States and other developed and intermediate countries are becoming less attractive because of environmental restrictions, radical reductions in tax incentives, and depleting reserves, causing people in the mining industry to begin looking at opportunities for foreign investment in gold mining concessions in lesser developed countries (LDCs). Meanwhile, LDCs are responding with chamber-of-commerce aplomb in marketing their opportunities. In the face of all this frenzy and hype, targeting gold mining concessions in LDCs for foreign investment may be done more objectively by employing a systematic approach. For this paper the SHOP rating system (Corbin, R.K., 1987), which considers factors of the LDC&apos;s stability, hospitability, ore occurrence, and profitability potential is used. The result is that a tiny banana-growing republic in Central America, first discovered by Columbus and named the "Rich Coast&apos;&apos; because of the many gold adornments worn by its Indians, has been rediscovered and emerges as a classic LDC gold target.

Jan 1, 1988

By L. S. Rubin

The efficient and acceptable disposal of fine coal refuse (28MxO) is one of the highest priority problems facing the coal industry today. For many years the established system for the disposal of this fine refuse slurry has been to concentrate the solids in a static thickener and pump the resulting 20-40% solids underflow to lagoons or impoundments. Although this technique has served the coal industry well, increasing environmental concerns and refuse related disasters, such as Buffalo Creek, West Virginia and Aberfan, Wales, Great Britain have resulted in federal and state regulations which now control fine refuse disposal methods. As a consequence of these regulations, the capital costs of constructing, maintaining, and operating regulatory complying impoundments has become in many cases economically unattractive. Areas processing topologies similar to those coal preparation plants of the Appalachians are particularly burdened by these regulations and are consequently turning to alternatives for handling and disposal of their fine coal refuse. The basic requirements of impoundment alternatives as defined by environmental and plant demands are: (1) A relatively solids-free liquid (1000 ppm or less) to serve as plant make-up water in a "closed circuit" system, and (2) a sufficiently dewatered solids product which can be combined with the coarse refuse to form a compactable stable land-fill.

Jan 1, 1978

By Jacques H. Nantel, James F. Archibald

INTRODUCTION The use of backfill materials in underground mines has been practiced for many years and the trend indicates an increased utilization of backfill materials in the future. The authors believe that underground uranium mines will follow this trend. Classified mill tailings, approximately 65 to 70 percent solids by weight, are the most common fill materials. Cement or other pozzolanic agents can be added to the fill materials to improve their strength characteristics. Dry fill, in the form of development muck, can also be introduced in the stopes to fill the voids left by the action of mining the ore. This paper deals mainly with the assessment of the radiation properties of backfill materials originating from uranium ores processed in the milling facilities of uranium mines. The paper outlines the results of studies conducted in the laboratory and in the field on radon emanating characteristics of backfill materials utilized in uranium mines. ROLE OF BACKFILL IN UNDERGROUND MINES Fill is a structural component of any underground mining system. In general terms, the purpose of filling is to provide ground support, to make recovery of pillars possible to provide a working platform for men and equipment, and to allow for waste disposal. There are other inherent advantages to the use of backfill underground, the most important being to: a) permit mining at greater depth b) allow the adoption of highly mechanized mining techniques c) reduce dilution from wall sloughing d) minimize roof and wall failures e) allow the mining of irregular orebodies, and f) to provide better control of ventilation. The last item is of great importance to uranium mine operators. The introduction of radioactive backfill underground represents an additional source of radioactive contamination; on the other hand the introduction of backfill in the mine reduces the volumes of workings to be ventilated. As a consequence the general mine ventilation is more effective and in most cases, better air quality can be maintained in the mine. There are of course some disadvantages associated with the use of hydraulic fills in underground mines, notably: a) the handling of large additional quantities of water from the underground workings b) delays caused by the cyclical nature of the backfilling operations c) additional costs associated with stope preparation and placement of backfill in stopes, and d) "spills" caused by bursting pipes or fill escaping from fill retaining structures. ASSESSMENT OF NON-RADIOACTIVE PROPERTIES Although the radioactive properties of mine backfills are discussed in this paper many other physical and chemical properties of backfills must also be considered. These properties include: a) percolation rate and permeability parameters b) viscosity versus pulp density relationships c) size analyses d) settling times e) settled bulk density f) solids specific gravity g) void ratio and porosity h) optimal percentage solids by weight i) specific gravity of slurry j) addition of cement:cement retention and loss k) unconfined compressive strength 1) triaxial compressive strength m) shear strength (non-cemented)

Jan 1, 1981

By Ralph E. Weeks

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1988

By John Drew Ridge

Recent work by Haas has made available information on densities and vapor pressures of solutions of differing salinities at temperatures up to 330°C. From these data it is possible to predict the behavior of volcanic exhalations of various degrees of salinity as they approach the sea floor. Particular attention is devoted to solutions of 5.0 weight per cent NaCl and 20 weight per cent NaCl, two fluids that approximate quite closely the salinities of what Roedder termed: (1) normal hydrothermal fluids and (2) fluids typical of stratiform deposits of low-temperature conditions of origin. It is apparent that solutions above 220-230°C. cannot reach a sea floor on which the depth of water is 600 feet or less in the liquid state but will boil at some appreciable depth beneath the sea floor. Such boiling would result in the precipitation of all constituents of the ore fluids of significantly lower vapor pressure than water. The principal such constituent would be salt, and no sulfide deposits, the major constituent of which is salt are known. It follows, therefore, that ore fluids probably never get close to the sea floor of shallow seas at temperatures high enough to permit boiling. Ore fluids significantly above 230°C. can reach the sea floor in the fluid state only if the depth of the sea in the area. in question is well above 600 feet, for example, solutions at temperatures of ±300°C. reach the sea floor in the liquid state only if the depth of sea water is slightly over 3000 feet. Ore fluids reaching the sea floor at such depths may be the parents of such fluids as the Red and Salton Sea brines. On the basis of these data, the Cyprus and Kuroko deposits are discussed.

Jan 1, 1973

By William J. Bryson

Just picture, if you will, the hot, lonely and desolate Ochre Mountains west of Salt Lake City. There works a grizzled old miner, his boots worn down, his clothes hang on a body stooped by years of hard labor. His skin is wrinkled and leather toughened by many years in the hot desert sun. His ever faithful burro stands patiently in the shade of a large rock as the tired old miner examines ore samples just acquired that very morning. Suddenly the old man&apos;s eyes widen, his breathing becomes rapid. &apos;Leaping to his feet, with a gleam in his eye, he cries, "Eureka, I&apos;m rich, I&apos;ve found the mother lode. This is where I will start my digging. " Without warning, the silent wilderness is alive with wild, shouting, charging figures! Frightened the old miner glances about him wide-eyed and pan- icky. His heart sinks, dismayed he now knows all is lost, this is the end. For there leaping from behind rocks and brush papers in hand, are the men from the Department of Interior, Bureau of Land Management, State Mine Inspectors, OSHA, MESA, EPA, OEO, and the never ending list of regulatory bodies related to todays mining industry.

Jan 1, 1975

By C. A. Pickles, S. J. Splinter

Silicon oxynitride, Si2N20, has many of the intrinsic properties of a potential high temperature engineering ceramic material. Some of these properties are similar to those of silicon nitride, which has been more intensively studied. However, although silicon nitride ceramics are approaching a state of microstructural refinement for various engineering applications, silicon oxynitride has received little attention. This has been mainly due to a lack of an economical and reproducible method of producing pure crystalline Si2N2O. Several reports exist on the preparation of crystalline Si2N2O from SiO2 and Si3N4, yet very little kinetic data exist. Even less is known about the carbothermic reduction of SiO2 in a nitrogen atmosphere to produce Si2N2O. In this paper, a review of the properties and methods of preparing silicon oxynitride will be presented. In addition, results obtained by reactively sintering SiO2 and Si3N4 will be discussed. The overall reaction is as follows:

Jan 1, 1990

By L. Yuan, J. H. Rowland, R. A. Thomas

"Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners. INTRODUCTION As many types of battery-powered mining equipment such as scoops and shield haulers are used in underground mining operations, charging stations are required to charge the equipment batteries. These batteries are of lead acid chemistry. A safety issue exists with the battery charging stations as all lead acid batteries produce flammable H2 gas during the normal charging process. Overcharging or excessive heat can quickly cause batteries to produce even more H2. If H2 is not appropriately diluted or dispersed, it builds up, and the risk of fire and explosion increases. Mine Safety and Health Administration (MSHA) regulation (30 CFR Part 75.340) requires that battery charging stations should be housed in noncombustible structures or be equipped with a fire suppression system. When a fire suppression system is used, the battery charging stations must be ventilated with intake air that is directed into a return air course or ventilated with intake air that is monitored for CO or smoke using an AMS. The monitoring of intake air ventilating battery charging stations should be done with sensors that are not affected by H2."

Jan 1, 2018

By Alan H. Goode

Of the 15 million tons of glass discarded in municipal wastes annually, about 2 million tons pass through incinerators and can be recovered by ore processing techniques. Although the primary use for this recovered waste glass would be as cullet in the manufacture of new glass containers, this approach is not always practical because of long shipping distances, high freight costs, and high purity requirements. Alternatives to the use of waste glass as cullet would be either as landfill or in secondary products. Although glass is considered a good landfill material, it is still wasteful of potentially valuable raw materials. Secondary products that can be made from waste glass1 include a variety of industrial and construction items. As part of the Bureau of Mines&apos; program in secondary materials recovery, the Tuscaloosa Metallurgy Research Laboratory has conducted research concerned with the development of ceramic building products from waste glass. Materials employed in this research were obtained from municipal incinerator residues fractionated in the Bureau&apos;s continuous residue processing plant, College Park Metallurgy Research center.&apos; The studies reported herein3,4 present research results using waste glass in the formulation and production of clay bricks, not only to produce improved products, but to reduce production costs, conserve natural raw materials, and most important, to reduce manufacturing energy requirements.

Jan 1, 1974

By Anthony D. Hammond

INTRODUCTION A two-dimensional approach for modeling narrow-vein deposits using the TECHBASE® software was implemented at Sunshine Mining for its use in the evaluation of mineral properties. This 2-D approach prevents the overestimation of high-grade tons typically associated with the use of fixed 3-D blocks and reduces the size of the model in computer memory. The method consists of constructing a two-dimensional model oriented along the average plane of the mineralized structure. This approach works well for single, multiple and intersecting veins with the condition that each vein is roughly planar with variation in dip or strike less than 30" in order to maintain a reasonable resolution in the process of projecting data onto a plane (Figure 1). Also, a precise identification of the hanging-wall and foot-wall location is critical in ensuring an accurate representation of the vein. By using various modeling techniques, the two-dimensional model estimates metal content, thickness, tonnage, economic and dilution parameters which will be ultimately used in the identification of minable reserves. The following is a generic description of the steps involved in modeling a steeply dipping vein. DATA ENTRY A typical project database consists of drillhole coordinates, survey information, assay data and any other quantitative or qualitative data. This database can be created inside the software or imported from any spreadsheet. TECHBASE® utilizes the concept of "fields" and "records" (columns and rows) for storing data. The use of "calculated fields" enables the user to expand on the manipulation of the database with minimum memory requirements. Another important feature of TECHBASE® is the ability to replicate the structure and format of the "tables" for its use in another project and the capability of running a series of repetitive tasks by means of batch and "runlog" files.

Jan 1, 1998

By Herman Gill, Dani Delaloye, Madelyn Rubin

The Foothill Tunnel is a remote 16-mile-long untreated drinking water tunnel in the San Francisco Public Utilities Commission’s (SFPUC) Hetch Hetchy Water and Power (HHWP) system. The 14-foot horseshoe shaped tunnel, constructed in the 1920s, is lined intermittently with concrete over approximately 53% of its length, with the balance being unlined rock. After detailed planning, in January of 2020 Mott MacDonald and HHWP staff completed a visual inspection and documented the condition of the tunnel with electronic data collection, photographs, and video with audio recording. The result was a comprehensive condition assessment that identified key areas of the tunnel to monitor.

Jun 13, 2021

By M. Quamrul Ahsan, Andrew Griffiths, Edward P. Jucevic

Heap leaching of precious metal ores using the cyanide process is extensively used in the Western U.S.A. for extracting gold. Consequently, the impact of cyanide in the spent heap is closely examined by environmental agencies and permitting authorities. Currently, many states require that all decomnissioned heaps be detoxified before abandonment. This paper describes a case study for detoxification of spent heaps at the ACH-Dayton Project using hydrogen peroxide. The chemistry of cyanide detoxification by hydrogen peroxide, together with simplicity of a detoxification operation, is discussed.

Jan 1, 1989