Search Documents

By Kef ton H. Teague

This paper will discuss bentonite deposits in Texas, Oklahoma, Louisiana, Mississippi and Alabama. The discussion will be re¬stricted to a review of the so-called calcium or non-swelling bentonites. In other words the exchangeable cation is calcium. The term "bentonite" is used to describe a clay material, composed essentially of the clay mineral montmorillonite. In addition, bentonites may contain various impurities such as glass shards, feldspar, quartz, muscovite and biotite mica, glauconite, pyrite, hydrated iron oxide, gypsum, organic material, etc, Most of the southern calcium bentonites contain at least 70% montmorillonite, Bentonite as mined may range in color from dark grayish greens through various shades of grays, reds, yellows and browns to nearly white. It is normally massive and breaks with a conchoidal fracture. When air dried, closely spaced shrinkage fractures occur. Moist bentonite has a soapy feel, with little or no obvious "grit". Bentonite deposits were first discovered in Mississippi about 1925, in southern Monroe County. During the thirties and early 1940's, deposits were identified in Alabama, Texas, Oklahoma, and Louisiana. Perhaps the earliest production of southern bentonite was from a deposit in the valley of the Tombigdee River, south of Jackson, Alabama in 1936. Production commenced in Mississippi during the latter part of 1938 at Pontotoc. The growth and development of the bentonite industry in the southern United States owes its beginning to three events. The first of these was the discovery by German researchers,

Jan 1, 1972

By D. F. McCarthy

INTRODUCTION Mined underground chambers specifically designed for the purpose of storing liquefied petroleum gas (LPG) at ambient temperatures have been in use for over thirty years. The first caverns were developed by Warren Petroleum of Tulsa, Oklahoma, in 1948, for its plants in Texas. The basic concept of an LPG-storage cavern is to create a space in an impervious formation at a depth sufficiently below the water table so that if any movement of fluid occurs the ground water will enter rather than the gas escape from the cavern. In the past, the primary reason for LPG storage underground has been its attractive cost advantages over steel storage on the surface. At current prices the cost of storing 7.949 ML (50,000 barrels) would be equivalent, whether stored on the surface or underground; whereas 79.494 ML (500,000 barrels) of storage underground costs only one-fifth of surface storage. It is usually uneconomical to excavate less than 79.494 cu m (50,000 barrels) of storage space. The fixed costs - engineering, mainshaft and ventilation shaft - are a substantial part of the total cost, whereas the incremental costs for excavating additional storage are relatively low. Recent concern over the hazards posed by the handling and storage of LPG and liquefied natural gas (LNG) has led to a new interest in the underground storage of these gases. Underground storage offers the following advantages: safety, security, low initial cost, low maintenance cost, operating, cost, minimum land require-

Jan 1, 1981

By Timothy P. Smirnoff, Arthur P. Chase, Herman J. Smith

INTRODUCTION The Newtown Creek Pollution Control Project (P.W. 53) is a major system of facilities designed to collect wastewater from large areas of the Boroughs of Manhattan, Brooklyn and Queens, then channel it to a treatment plant where the wastewater is processed and discharged. The North Branch interceptor collects wastewater along the east side of Manhattan and transports it downstream to a Junction Chamber at Avenue "D" near East 13th Street. The South Branch interceptor similarly collects wastewater from the southern part of Manhattan Island on both east and west sides of Manhattan and transports it to the same Junction Chamber from where both flows are delivered to the adjacent Manhattan Pumping Station which pumps the wastewater under the East River to a treatment plant in Brooklyn. This system is shown in Figure 1. Construction of the Manhattan Pumping Station began in the Summer of 1966 and was delayed by a number of mishaps. In the vicinity of the North and South Interceptors, approximately 3,060 cubic meters (4,000 cubic yards) of soil flowed into the excavation: 765 cubic meters (1,000 cubic yards) at the North Branch Interceptor, and approximately 2,300 cubic meters (3,000 cubic yards) at the South Interceptor. These movements were accompanied by surface subsidence, collapse, or both. On June 4, 1973, while pumping station construction was underway, approximately five to seven cubic yards of sand entered the junction chamber through a temporary bulkhead valve in the North Branch Interceptor.

Jan 1, 1979

By Jim Peregoy

INTRODUCTION Frontier-Kemper Constructors, Inc. is an Evansville, Indiana based heavy construction contractor engaged in projects for both the public and private sectors of the underground construction industry. Construction activities range from conventional shaft, slope, tunnel and chamber excavation through state-of-the-art mechanical excavation, ground freezing, standard support and structural concrete operations. Conventional excavation and concreting equipment, as well as raise boring machines, road headers, tunnel boring machines, and freeze plants are owned, operated, maintained and modified "in-house" to suit the needs of individual projects. The balance of this paper wilt present a general overview of the Frontier-Kemper planning and construction operations on the recently completed Phase II of the U.S. Army Corps of Engineers, John Day Dam, Juvenile Fish Bypass Project. General Project History The U.S. Army Corps of Engineers is responsible for designing, constructing and maintaining various navigation and impoundment structures on the nation's inland waterways. Maintenance involves both the work required to maintain the structure in fully-operable condition and the ongoing work required to maintain a positive impact on the environment. John Day Dam is located on the Columbia River approximately 95 km (60 miles) upstream of The Dalles, Oregon. It was constructed to: provide electric power to the Pacific Northwest; provide Locking for up-and-downstream bound commercial and private watercraft; act as a water impoundment structure to control flooding conditions; and to provide a source of irrigation water

Jan 1, 1987

By Annan Cook

Cyprus Metals' Sierrita mine is located in the Pima Mining District, Pima County, Arizona (Fig. 1), which is one of the largest known porphyry copper districts. The ore body is part of a large mineralized system that includes Cyprus' adjoining Esperanza mine. The copper and molybdenum grades being mined at Sierrita make it one of the two lowest grade porphyry copper mines in the world Mineral production from the district was first recorded in 1876. Copper from replacement deposits in carbonate rocks and copper¬-lead-zinc from veins in volcanic rocks were mined from several deposits. However, it was not until 1957 that the district commenced to become a major copper producer with the beginning of production from the Pima mine, which was the first open pit operation. Since that time, seven other open pit mines have come into production. Because of the variable copper prices and high operating costs, not all of the mines are operating today. A map of certain outcrops, plutons, and open pits, as well as older underground mining operations, in the Pima district is shown in Fig. 2.

Jan 1, 1991

By G. Tapia, R. J. Kelley

Empresa Minera de Mantos Blancos S.A. operates two copper mines in Chile: Mantos Blancos and Mantoverde. Oxide ore is processed by acid leaching followed by SX-EW to produce copper cathodes. In order to define the leach process adequately for each ore, an extensive metallurgical testwork program was carried out during the feasibility study for each of these projects. A combination of heap and dump leaching was selected for Mantoverde, while a modification to the existing vat leach operation was selected for Mantos Blancos.

Jan 1, 1998

By Laurel E. Burns

Alaska is in competition with the rest of the world for exploration dollars. Providing a "seed package" of airborne geophysical data for the state's numerous mining districts encourages companies to begin more detailed exploration in more areas than they could have afforded on their own. When data are already available, the initial risk decreases for people involved in exploration. Airborne magnetic and electromagnetic data help ge¬ologists and geophysicists determine what rocks and structures are present under overburden and vegetation. These data form a fundamental package that exploration companies want before intensively exploring most regions. Individual mining companies have conducted their own geophysical surveys during the past several decades. However, these data are not available to other companies. The companies able to afford geophysical surveys have less money for ground exploration after purchasing expensive, private geophysical data. Therefore, they are not able to explore as many places as they might. Additionally, since data are not shared with other exploration companies, the proprietary surveys do not foster intercompany competition to move projects forward. Individual prospectors and small companies can not afford their own geophysical surveys. "It is more often than not the grassroots exploration efforts of the smaller operator that leads to significant discoveries," said Klaus M. Zeitler, senior vice president for development and exploration at Teck Exploration. Acquiring and releasing the geophysical data to the public produces several benefits. The increased explo- [ ]

Jan 1, 1998

By Brad C. Lewis

The coal mining industry has experienced a general trend toward longwall operations. An increasing percentage of underground coal is being mined by longwalls. And productivity in longwalls is likewise increasing. Operators of longwalls, however, have not yet reached a state of mining euphoria. Competitiveness within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. [Figures 1, 2 and 3] present trends in the industry. Longwall mines, as defined here, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Nonlongwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation. Annual percent increases in productivity appear to have peaked in the 1985-1987 time frame. This was due, in part, to implementation of technological advancements and improvements in management-labor relations. The results shown in [Fig. 3] aroused the author's curiosity. The first question was "Have technological advancements to increase productivity peaked?" It does not appear so.

Jan 1, 1990

"With a longstanding reputation for engineering expertise, Weir Minerals continually develops solutions and technology to better serve the mining industry. Recognizing that throatbush wear rate has a major impact on the overall efficiency of slurry pumps, Weir Minerals has developed superior rotating and axial adjustment technology.In many applications, the pump’s throatbush is the component that has the shortest life compared to the impeller and liners, with considerable variability.Adjusting the gap between the throatbush and the impeller front shroud reduces hydraulic recirculation in the pump. This prevents localized wear on the throatbush, improves hydraulic efficiency and lowers the total ownership cost for the operator. To avoid impacting the plant’s production, these adjustments are often performed while the pump is operating. However, this can have safety implications for individuals working at the front of the pump unit.“Manually adjusting an alloy throatbush on a large pump requires several people and is laborintensive. It requires mechanical tools to adjust the four pusher bolts, one at a time, in order to reduce the gap between the throatbush and impeller. We wanted to find a safer and quicker way to extend the wear life of the pump with regular adjustments, which led us to development of this technology,” said Marcus Lane, global product manager for centrifugal pumps for Weir Minerals.“Our automated throatbush adjustment solutions are available for pumps fitted with either rubber or alloy throatbushes on Warman slurry pumps used in the most arduous applications, and have been designed with our customers’ safety and pump operation in mind. By mechanizing the adjustment procedure, personnel are removed from the line of fire, and the accuracy of axial movement is increased,” said Ron Bourgeois, director of slurry pumping technology group for Weir Minerals."

Mar 1, 2019

By John Murray, Daniel Ebin, Robert Gould

The Atlanta Plane Train project at Hartsfield-Jackson Atlanta International Airport employed the progressive design-build approach. This provided opportunities for collaboration between the design-builder, design engineer, and owner and the implementation of innovative design and construction approaches. The innovations have reduced risks, allowed for adjustments during design to accommodate new challenges, and provided open-book cost and schedule evaluations. The progressive design-build approach has also allowed for pricing of work to occur in phases—capturing the design/construction challenges as the project evolves and when they are more clearly defined. While this has allowed for pricing to be performed with better project understanding and therefore less contingency, the associated time frame for approvals has required careful consideration to avoid impacts to the schedule. This paper discusses the benefits and challenges of the progressive design-build approach.

Dec 1, 2022

By Peter J. Tarkoy, Terence G. McCusker

INTRODUCTION The discovery of oil and gas reserves in the North American Arctic has led to substantial thought being given to their development. Systems adequate for exploration are not always, or even often, suitable for permanent installations. Combinations of offshore pipeline, drilling ships, platforms, sub-sea systems, sand islands and -ice island bases have been proposed. However, conditions in the Arctic are such that these methods may be difficult or impossible to implement. Problems exist with (1) the freezing of the Arctic Ocean surface for 9 - 10 months per year, (2) the movement of sea ice, (3) scouring of bottom sediments by ice islands and icebergs to great depths below the ocean bottom and (4) deep water channels. Any method which can avoid the problems associated with surface construction in these very adverse conditions merits detailed examination. One of the proposed solutions is to tunnel from a convenient or available access point to a point within the field, construct a chamber large enough to accommodate the drilling equipment and drill the development wells in a protected environment. Service and delivery lines would use the access tunnel and further tunnels and chambers would be constructed in a radiating pattern to develop the whole field. In order to determine the feasibility of underground construction in the North American Arctic, it is first necessary to understand the geologic and environmental factors which would affect such construction, to be knowledgeable concerning the problems and then to consider the techniques appropriate to the conditions which will be encountered, bearing in mind the need to minimize both con-

Jan 1, 1976

By D. M. Range

Exxon is reclaiming an 80 hectare (200 acre) Wyoming uranium tailings basin (10 Mt) in accordance with U.S. Nuclear Regulatory Commission requirements. The reclamation plan is designed to control the tailings and their radioactive emissions for at least 1000 years. Rigorous modeling and analyses of potential erosion by wind and water were used in planning. The use of riprap was minimized and the need for long term reclamation maintenance was eliminated. The resulting design is similar to erosionally stable regions created by nature. The concepts used in the design and implantation have wider reclamation application.

Jan 1, 1989

By E. J. Beckman, R. M. Enick, C. Shi

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. Two inexpensive and environmentally benign fluids were selected for the study, water and carbon dioxide. The separation, which is conducted at 295 K and at the vapor pressure of carbon dioxide (6.0 MPa), is based on differences in wettability between the precious metals and other minerals. Contact-angle results indicated that, in the presence of water and liquid CO2, gold is slightly hydrophobic. The addition of CO2-soluble fluoroalkyl thiols or f uoroetherthiols increased the hydrophobicity of gold exposed to water and CO2 to a greater extent than alkylthiols. Minerals, including quartz, pyrite and magnetite, were hydrophilic. During the separation, an aqueous slurry of fine mineral and gold particles was mixed with liquid carbon dioxide. Pure gold particles (-325 mesh) were found to agglomerate at the H2O-CO2 interface. The minerals tended to remain in the aqueous phase. Despite these promising preliminary results, very poor gold recoveries were obtained when applying the procedure to an Australian gravity concentrate. This was attributed to the native gold particles in the concentrate being either too large, agglomerated in slimes or coated with minerals. Although this particular application was unsuccessful, this water-CO2 biphase technique may be applicable for other separations that require the removal of very fine, hydrophobic particles from an aqueous slurry.

Jan 1, 2000

By R. C. Freas

Imported products and materials have been in the news over the last several years in a wide variety of industries. Certainly the mining and industrial minerals industry has not been exempt from this. Cement imports have received considerable attention in the press and a number of written articles. We are also seeing imported aggregates particularly along the gulf coast and east coast of the United states. We are now hearing increasing talk of bringing high brightness calcium carbonate from offshore sources into the U.s. domestic markets. This paper takes a look at the location of these sources, factors affecting their acceptance by U.S. industry and presents a general cost comparison of offshore and domestic calcium carbonate. In addition, the market response of U.S. suppliers and the impact of imports is also discussed.

Jan 1, 1989

By John W. Rushton

THE PLANNED MAINTENANCE PROGRAM All concentrators should start with a planned maintenance program from day one. Every- body thinks they have a program in place before start-up, but in reality, most have only a fraction of what is needed to avoid the "Post Start-up Disaster" (PSD) - two years for start-up is not that uncommon. An effective program has all of the following: (1) Good people. (2) Area Maintenance. (3) Good PM Checklists. (4) Daily Work Schedules. (5) Written Work Orders. (6) Equipment Histories. (7) Backlog Control. The installation of a workable program takes hard work, talent, and commitment. You have to know what you are doing (hard work will not replace talent). Good People Good people are available in any location if you make the effort. Always check references carefully (both superiors, peers and subordinates). Was the last concentrator they worked at successful? Was it clean? Find out! Success or failure follows people around. I know people who are experts on PSD because they have lived through it three or four times. You need some college trained people with hands-on experience. There are no secrets, you have to make the effort. If you make a mistake in hiring (and you probably will), make the tough decision necessary to rectify it quickly. Area Maintenance Area maintenance refers to organization of supervision such that one person is uniquely accountable for every inch of ground and piece of equipment. Avoid overlapping authority if at all possible. You must have a planner as a staff position. A foreman cannot effectively plan and

Jan 1, 1986

By L. G. Austin

Introduction My first contact with industrial milling was during the time I worked in the electricity generating industry in the United Kingdom. In visits to power stations to investigate either deposits in the boiler furnaces or polluting deposits settling around the stacks. I had to check the performance of the vertical coal pulverizers, since poor pulverization aggravated both problems. Naturally, then, when I came to the USA in 1957 to take a PhD in fuel technology at Penn State, I was put to work to review the science of coal pulverization. After this reviewing, I was completely confused. On one hand, there was a well-developed understanding of stress-strain equations, and a rap- idly developing knowledge of how stressed, brittle solids fractured, based on the Griffith crack theory. On the other hand, reading in the grinding literature gave me: • Kick's Law, which was clearly not correct in the light of modern fracture theory; • Rittinger's Law, which was also clearly not correct; • Bond's Third Law of Comminution, which was claimed to have something to do with the Griffith crack theory, but where the connection between the two was made by intuitive pseudo- scientific reasoning I could not accept; • the choice of mill motor power for the most common type of coal mill, the Raymond pulverizer, was calculated from the fan power required to move air through the mill. Although I could accept the empirical connection between the two, it made no sense from the point of view of fracture energy. Even today, most books or review chapters on size reduction start from these laws. incorrect statements abound in the literature, such as “the Hardgrove Index is based on Rittinger's Law," which it is not, "The Bond theory states that work input is proportional to new crack tip length produced in particle breakage," which is not true, etc. My own test work showed that these "laws" did not fit the data for grinding of coal. At about this time, Epstein (1 948) and Broadbent and Callcott (1 956), following the original work by R.L. Brown (1941) at the British Coal Utilization Research Association, proposed describing breakage as a series of fracture stages. I took their concepts and developed the basic differential equation for a batch grinding process continuous in time, analogous to a batch chemical reactor. Robin Gardner then joined the project and did his PhD on treating batch grinding in the same way as a batch chemical reactor. He found that the basic equation had already been partially derived by Sedlatschek and Bass (1 953) in Germany. We confirmed experimentally the validity of the equations for describing batch grinding (1 962) and formulated the equation describing steady-state continuous grinding in a fully-mixed mill. At about the time this work was published, Gaudin and Meloy (1962) and Filippov (1961) independently published essentially the same equations, but without experimental proof of the validity of the concepts. I will give a brief overview of what these beginnings had led to in the design of mills for size and power, and show some of the results of this more detailed understanding of grinding processes. Concepts of Fracture Mills such as tumbling ball, rod, pebble and autogenous mills and vertical mills such as the Raymond, and E-type apply compressive stress to lumps or particles relatively slowly. Compressive stress applied to a particle of an elastic brittle solid imparts overall strain energy to the solid and produces local regions of tensile stress, (Fig. 1) (Berenbaum and Brodie, 1959). Irwin (1949) showed from solution of the stress-strain solutions that a small hole in a region of tensile stress reduces stress concentration at the hole, that is, the tensile stress at the tip of a crack or flaw in a solid is much higher than the general tensile stress in the region. The longer the crack, the higher the stress concentration. Griffith (1920) hypothesized that when the regional tensile stress is large enough, then the chemical bonds at a preexisting crack tip are stretched to breaking point, as illustrated in Fig. 2. When the bonds break, the crack becomes longer, the tensile stress concentration increases, the situation is unstable and a crack opens up (propagates) a surface of tensile stress, creating its own tensile stress at the leading edge. Stored strain energy is converted to the kinetic energy of the moving stress field, which is analogous to sound propagation through the solid, so the crack tip accelerates to velocities approaching those of sound. The moving crack will pass through regions that were previously under regional compressive stress. The equations for "ideal" and "Griffith" strengths are where a is the intermolecular distance, y is Young's modulus, g is the energy

Jan 1, 1998

By Valcana Stoyanova

The distribution pattern, abundance variations and types of polymetallic nodules and associated megabenthic communities in area covers more than 60 000 km2 laid out in the eastern Clarion-Clipperton Zone (CCZ) is presented. Our observations are based on data from 158 boxcore stations collected during the cruise of the Interoceanmetal (IOM) in 2004 on board of RV Yuzhmorgeologiya. Although those polymetallic nodules for two decades been subject to prospecting and exploration studies carried out by IOM, the knowledge of megabenthic communities and their distribution pattern within nodule field was extremely limited. With purpose to evaluate the relationship between polymetallic nodules and associated benthic megafauna, an comparison analyze was carried out in respect to their composition, types, abundance across the studied area owing into account the local particular feature of bottom topography. It is suggested that the nodule-bearing seafloor supported more diverse fauna (higher number of morphotypes) than the nodule-free areas. Moreover, based on correlation between types of nodules and associated faunal morphotypes frequency the apparent relationship is considered. The most abundant megafaunal taxa (between 68 ? 92%) is essentially associated with the occurrence of the diagenetically growth nodules type (D-type and its D1-subtype); the role of the H and HD nodule-types was variable. In respect to the bottom topography, the highest diversity in the structure of megafaunal communities was recorded in the gently undulating plains and on the horst slopes, thus the highest nodule abundance occur on the topographic slopes.

Jan 1, 2008

By William H. Sutherland

INTRODUCTION Coal workers' pneumoconiosis and sili- cosis are only two of several diseases which are rlassed as pneumoconiosis. These are respiratory diseases caused by dusts which are inhaled and accumulated in the lungs. The individual particles of dust cannot be seen by the human eye. They are so small that they escape the natural cleansing mechanism of the nose and air passages and make their way down to the terminal air sacs of the lung where they injure the cells and cause the formation of scar tissue. Consequently, if there is exposure to high concentrations of dust over a period of time - usually, a number of years - the amount of scar tissue increases and begins to impair breathing. As a result, the miner develops shortness of breath, coughing and wheezing ad-if exposure continues - this progresses to permanent disability and frequently to death. Death is often due to pulmonary heart disease, the effect of stress on the heart 2s it tries to compensate for the weakened lungs. Specifically, silicosis is an occupational lung disease caused by the accumulation of free silica (quartz) in the lungs. Silicosis is considered the most important form of pneumoconiosis, not only because of its seriousness as a respiratory crippler, but also because of the large number of workers who risk contracting it in a variety of occupations. Quartz is one of the most common substances of the earth's crust, estimated at about 60 percent. Silicosis has been found in coal, metal and granite miners, as well as in other workers, such as sandblasters and pottery makers. Silicosis is also known to predispose the lung to tuberculosis and to increase the chances that a worker will contract chronic bronchitis and emphysema. The seriousness of silicosis was tragically brought to public attention about 50 years ago. During 1932-34, workers were involved in digging a tunnel through rock at Gauley Bridge, West Virginia. While their exposure time was relatively short, they developed silicosis because of the high concentrations of quartz. By 1936, 476 workers had died of silicosis and about 1500 were believed to have the disease (Washington Post, 1982). It is difficult to tell how many coal miners have silicosis. Because x-rays and breathing function tests do not show the difference the type of pneumoconiosis is generally diagnosed by the miner's work history. For example, if a worker

Jan 1, 1986

By Wen-Long Cai, A. Frederick Banfield

This paper investigates, through case studies on a porphyry copper and a coal deposit, the differences and relevances between an approximate production schedule approach, i.e., the best case and the worst case schedules and a practical production schedule approach. The comparisons were with regards to: 1) choosing an optimum ultimate pit size, 2) determining processing capacities, 3) selecting 'optimum' cutoff grades, and 4) blending. The comparison criteria was to maximize the project net present value. Conclusions were drawn based on the study results.

Jan 1, 1996

By D. I. Phillips, P. J. Bethell

This paper focuses on the -1/2 mm cleaning at Elk Run Coal. The original circuitry incorporated desliming cyclones. Problems with slimes entrainment in the cyclone underflow (froth cell feed) resulted in poor froth cell selectivity. Laboratory test work led to the installation of high frequency desliming screens. Consequently, great improvement in cell performance was brought about by enhanced desliming with the ability to use split flotation. The modifications resulted in significant improvement in total plant performance and overall yield while maintaining clean coal quality.

Jan 1, 1987