Search Documents

By C. Klauber, H. G. Linge, W. G. Jones

The carbon-in-pulp process for gold processing depends on the adsorption of dissolved Au(CN)2- from solution onto activated carbon. Our work shows that coconut and peat based carbons have the same mechanism and kinetics of adsorption. There is no contribution to the bonding from carbon-oxygen functionalities on the carbon surface, as has been invariably supposed in all previous theories for the mechanism of the reaction. It is shown that Au(CN)2- is reversibly adsorbed intact on, and parallel to, the graphitic planes of the carbon. The physiochemical basis of the measurement of carbon reactivity for gold adsorption is discussed.

Jan 1, 1989

By Antonio Peralta, Guillermo Dante Ramírez-Rodríguez

Mining is generally considered a large-scale hightech industry. However, it has estimated that about 12 million people, about 30% of the world’s total mining workforce, relied on small-scale mining for their livelihoods. During the years, the large-scale mining industry has developed best practice environmental procedures, which have been applied in diverse settings through the world. In contrast, small-scale mining is better known for its high environmental impact and the lack of safe and healthy working conditions. This paper will discuss the environmental control strategies used by the large-scale mining industry, and its applicability to small-scale mining in developing countries.

Jan 1, 2005

By Kenneth N. Han, Xinghui Meng

The leaching of gold and silver from various ores in ammoniacal solutions conta1mng various oxidants has been investigated. The samples tested included elemental gold, sulfidic as well as carbonaceous refractory ores, and tellurides. When pure elemental gold powders were used, the maximum amount of gold dissolved under the conditions studied was 16.3 ppm, 42.4 ppm, 82.0 ppm, and 152.2 ppm, respectively, at 140°C, 160° C, 180° C, and 200°C. Five different refractory ore samples were also tested. The recoveries of gold and silver from these refractory ores were typically 92% and 95%, respectively.

Jan 1, 1992

By Jody Kelso, Thomas R. Clark, Gregory J. Olson

Refractory, sulfidic gold ore from the Metates deposit in Mexico was tested to determine if it could be heap biooxidized to improve gold extraction. Small column tests were conducted in a manner consistent with anticipated process conditions: increased tempera­ture due to oxidation of the high sulfide content ofMetates ore and full recycle application of leach solutions containing high concen­trations of dissolved solids. Biooxidation by thermophilic (heat­loving) microorganisms was tested to determine: 1. the extent of sulfide oxidation and bottle roll precious metal recovery, 2. reagent consumption, and 3. potential solution flow problems due to mineral precipitation.

Jan 1, 1998

By R. Llerena, P. Dunstan, R. L. Amelunxen

A single four feet diameter cell, treating a Cu/Mo rougher concentrate, has been fully instrumented and linked to a Distributed Control System. This has enabled the writers to further understand the mechanics of operation of the cell, particularly that of the "TRANSITION ZONE". This is the volume between the feed port and the pulp-froth inter- face. The results have shown a need for the re-designing the control loops whereby the Transition Zone volume (or pulp level ) becomes the single most important control parameter to achieve the de- sired recovery. Air consumption, previously thought to have played this role, is now kept at precoalescence level s for maximum efficiency.

Jan 1, 1988

By John B. Ackerman, John G. Mansanti

INTRODUCTION Placer Dome's Turquoise Ridge Joint Venture operation is located some 75 km northeast of Winnemucca, a community in north central Nevada. Formerly known as the Getchell Gold Corporation and First Miss Gold, the operation mines refractory ore from the Getchell and Turquoise Ridge gold deposits located on the east flank of the Osgood Mountain Range above the Kelly Creek Basin in the Potosi Mining District. Mining has been ongoing at Getchell since shortly after its discovery in 1934, and was the nation's second leading producer of gold after Homestake in the early 1940s. Over its history the Getchell property has been mined for gold, tungsten, molybdenum and arsenic; mining methods varied from open pit mining to underground mining; processing options included conventional milling, flotation, roasting, heap leaching, and most recently pressure oxidation followed by CIL (carbon-in-leach). As an historical note, the US Bureau of Mines developed the use of carbon for gold recovery at Getchell during the 1940s (Horton 1999). Placer Dome acquired the property in May 1999. The pressure oxidation plant was mothballed in July 1999 and the property was placed on care and maintenance in February 2002 pending further exploration results. The property is currently ramping up to full production status. A joint venture agreement (75% Placer Dome, 25% Newmont) was established with Newmont Mining in 2003 and ore is processed at their nearby Twin Creeks autoclave plant. Mine dewatering is a key element to success. Arsenic is a ubiquitous mineral in many of the mineralized areas of northern Nevada, necessitating treatment of water prior to re-infiltration.

Jan 1, 2005

By O. J. R. Baena, D. E. Chaverra, C. D. L. Ramirez

Cyanide is one of the most used reagents in the precious metal extraction process; as well as the most efficient from the point of view of the dissolution process; but it is also a toxic product that requires a lot of care in handling. Likewise, the residual solutions of the process must be followed because they can be a risk of contamination of water, animals and human health. In the artisanal processes of obtaining gold and silver, neutralization of the residual solutions is used to passivate the present cyanide. During this process ammonium cyanate is formed which decomposes rapidly in the presence of air and sunlight in carbon dioxide and ammonia gas, contributing to the greenhouse effect. In this work the use of the ammonium cyanate obtained in the process of neutralization of the cyanide solutions as a reagent to obtain urea is proposed. Urea was obtained indirectly through the use of the reagent kit UREA/BUN-COLOR. The process is effective at pH ≤ 4.5 with a rapid increase in solution temperature, and addition of hydrogen peroxide. The urea crystals begin to form at 50°C. The cyanide / urea ratio obtained was 1 / 7.5 INTRODUCTION In the processes of extractive gold metallurgy, the use of cyanide leaching is perhaps the most widely used method worldwide; by the ease of operation, its low cost and high levels of precious metal recovery. However, neutralization, in most processing plants, is not done properly, and leftovers of solution with free cyanide are dumped in concentrations harmful to the environment, in particular animals and humans. Cyanide can enter surface water through releases from industries using cyanides. Due to its high toxicity, the presence of cyanide in water is a matter of great concern (Jawale et al., 2017). The pollution generated by the effluents from the leaching of gold ores is one of the main obstacles of social opposition presented by mining activity due to the impact of both surface and groundwater. During the cyanide decomposition process, a compound known as ammonium cyanate OCN(NH4), which is a raw material for the manufacture of urea, CO(NH2)2 is generated. In the case of good neutralization, cyanide is no longer a toxic compound through oxidizing reagents, but as a result, there is the generation and emission of ammonia and carbon dioxide into the atmosphere, generating both a greenhouse effect (Gómez, 2012). This is evidenced by the strong effervescence of the reaction, and a penetrating smell of ammonia, which can irritate respiratory mucous membranes and eyes; however because they are greenhouse gases they are considered pollutants.

Jan 1, 2019

By R. L. White

Classification of Mills Mills may be classified under four categories that relate to the type of action utilized to grind the material: Tumbling. The most important of these to the minerals processing industry are tumbling mills. Grinding media is actuated in a free¬form pattern in a rotating drum causing it to tumble, material being ground passing through the tumbling media. Work is done by a combi¬nation of attrition and impact. Impact. Grinding media is actuated in a distinctive pattern so that it impacts the material being ground. Work is done by impact. Roller. Grinding media is actuated in a distinctive pattern, mate¬rial being ground passing under or between the media. Work is done by compression. Fluid Energy. There is no grinding media as such. Energy is imparted to the material by transfer of kinetic energy from the fluid to the material. Grinding is accomplished by interparticle impact and attrition. Tumbling Mitts The main physical arrangement consists of a lined cylindrical drum mounted on trunnion bearings driven by a ring gear and pinion, in turn connected directly or through a reducer to the electric motor. Variations to this general arrangement include: (1) Drum mounted on rollers instead of trunnions. (2) Bearings on the drum directly, not on trunnions. (3) Utilization of multiple pinions on the gear. (4) Trunnion-type drive arrangement through a gear reducer with¬out the use of a ring gear. (5) Motor rotor mounted directly on the drum with stator around the drum, thus eliminating the gearing. The drum consists of a shell and heads lined with replaceable liners of various types and configurations. Various types of tumbling mills are tabulated; illustrations of some are shown. The types are so designed for specific purposes. Media utilized include steel rods, balls, or rock of the same material as being ground or of special material in the instance where iron contami¬nation is detrimental (see Figs. 9 and 10 and Table 2). Impact Mills Although there may be some overlapping of interpretation of terms, impact mills are considered those in which the media is actuated in a distinctive manner, at relatively high speed, impacting the material to be ground. There is an overlapping also in what may be considered to be crushing equipment rather than grinding equipment. Hammer Mill or Impactor. Material is fed into the equipment; inside hammers of impactors revolve at a high speed, breaking the material on impact with the hammers (see Fig. 11). Material is also thrown against the periphery of the mill, causing impact grinding to occur. Equipment is normally lined with replaceable abrasive resis¬tant metal; hammers are also

Jan 1, 1985

By S. T. Krukowski

Traditionally the lime industry is governed by market, location, and transportation. These factors also may act as obstacles to global market access. Lime manufacture responds to market opportunities by first focusing on location. Lime markets are diverse and widespread, and ubiquitous occurrences of limestone make development of a widespread industry possible. Lime’s low to moderate unit value restricts transporting it long distances. Other factors (including lime reactivity, dedicated container use and other liabilities) limit shipping lime far. In the past many small to medium size companies made lime for local use. Today the global aspect of the industry is ownership by few large companies producing lime for local consumption.

Jan 1, 2003

By W. R. Mackenzie, C. A. MacDonald

Oxide copper was discovered in 1946 at Guelb Moghrein. Early work culminated in the construction in 1970, by a consortium headed by the Anglo American group, of a project producing copper concentrates from 1,000,000 tonnes per annum of oxide ore. The process used was the TORCO (Treatment Of Refractory Copper Ores) process, which reduced oxide copper minerals to elemental copper by roasting in fluidised beds at 800°C with salt and coal. The roaster product was then floated to yield a high grade smelter concentrate, which was exported. The project closed in 1976, due to low copper prices and increased energy prices, leaving an open pit, the old TORCO plant, a water pipeline, and more than 2,000,000 tonnes of tail­ings, which contained remnant copper, as well as an average of 3 git of gold. After several attempts to recommence operations at Akjoujt, recovery of gold from the old TORCO tailings was started in 1992 by a joint venture company known as MORAK (Mines d'Or d'Akjoujt). This company comprises General Gold Resources N.L. of Australia, who are the managing partner, SAMlN (La Societe Arabe des Mines d'Inchiri) and the International Finance Corporation. Because the tailings are high in copper (0.1-0.3% Cu), the project used the 'Hunt' process, which uses a combination of cyanide and ammonia to leach gold while suppressing copper extraction. The gold is recovered from leach liquor by carbon absorption.

Jan 1, 1996

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By H. L. Owens, J. W. Fredland, K. K. Wu

The Mine Safety and Health Administration (MSHA) is responsible for reviewing and approving the engineering plans for impoundments, of significant size or hazard potential, that are constructed on coal-mine property. Over the years, technical review criteria have been updated as the state-of-the-practice for dam safety has evolved. The evaluation of stability under earthquake loading, for example, has gotten much more sophisticated for impoundments built using upstream construction. Recent incidents where slurry has broken into mine workings have caused MSHA, mine operators, and design engineers to re-examine this safety issue. This paper gives an overview of MSHA’s impoundment plan review process.

Jan 1, 2003

By J. Finch, J. Yianatos, N. W. Johnson, R. Espinosa-Gomez

A method of determining the maximum concentrate solids rate or carrying capacity is described for given column operating conditions. The method requires alteration of the feed rate of solids to the column at a fixed residence time by manipulation of the % solid of the column feed pulp or the bias rate. The carrying capacity was measured for five streams at the Mt. Isa Mines Pb/Zn and Cu concentrators. As a potential scale up parameter, the mass of solids per unit time per unit column cross section (Ca, g/min.cm2) is explored. Ca is tentatively related linearly to the 80% passing size (d80) of the concentrate. For d80 < 15 pm Ca was less than 4 g/min.cm2 (8 lb/min.ft2) which makes it a critical consideration in scale-up for such fine feeds. An alternative carrying capacity parameter, mass of solids per unit volume of gas Cg was not as useful as Ca since Cg varied inversely with gas rate.

Jan 1, 1988

By K. N. Han, J. J. Kellar, Y. Guan

The adsorption of zinc species onto silica in ammoniacal solutions was studied. The adsorption isotherms indicated that the adsorption of zinc increased with increasing pH. The adsorption density increased as the zinc equilibrium concentration increased up to =3.5x10-4 M. Above this concentration, the adsorption density was independent of the equilibrium concentration, and a maxima adsorption density was reached. Temperature had no significant effect on the adsorption density.

Jan 1, 1995

By Immo H. Redeker

This is a final progress report on a cooperative project conducted by three private feldspar companies,** North Carolina State University, and the federal Bureau of Mines. The object of the project was to reduce the feldspar tailings disposal problems at the flotation plants in the Spruce Pine area of North Carolina. The initial phase of the project revealed that high tonnages of saleable feldspar and quartz were lost in the tailings and the three feldspar companies are now concentrating their efforts on feldspar recovery, either by reclamation from the tailings as suggested by the Asheville Minerals Research Laboratory or by improvements in metallurgy in the existing plants.

Jan 1, 1970

By W. L. Oliveira, J. R. Sobrinho, V. M. Hamza, S. M. Eston

The Ipueira III chrome mine is located in the northeastern part of the state of Bahia, Brazil. Extraction is actually at depths less than 300 m, but below level 200 serious environmental problems have been encountered with respect to control of air quality, toxic gas, dust and thermal comfort. At the request of the mining company the University of São Paulo started a research program to investigate the origin and occurrence of the critical problems and to propose solutions. A ventilation survey was carried out first which revealed the existence of several air leakages and short circuits that contributed to substantial reductions in the air supply to some of the main producing levels. Computer simulation of the ventilation network showed that extending the intake air shaft to deeper levels was the most convenient and economic solution to improve the air quality. The ventilation survey was followed by a mapping of the toxic gas emissions and thermal comfort levels in several parts of the mine. The air quality conditions were evaluated as a function of gas emission and heat generation associated with production and development activities. The results show that environmental conditions are already critical in most of the working levels and neither an increase in production nor deepening of the mine can be taken up without substantial changes in the ventilation system. INTRODUCTION Environmental concern is growing in Brazil and several underground mines are starting environmental engineering programs. The LACASEMIN - Laboratory of Environmental Control and Mine Safety of the Mining Engineering Department of the University of São Paulo - was contacted by Mineração Vale do Jacurici to start a research program for investigating the origin and occurrence of environmental problems that existed in the Ipueira III chrome mine. This research program involved field measurements of air quantities with gas levels monitoring, evaluation of heat stress parameters, determination of adequate flow patterns through computer simulations and training of mine technical staff. This paper presents the results of the first 4 months of this research program. The Ipueira III mine is located in the northeastern part of the state of Bahia, near the city of Senhor do Bonfim at about 400 km inland from the state capital city of Salvador. Chromite mineralization is quite widespread in this area and often associated with mafic and ultramafic rocks which cut across regional gneisses and migmatites. ROM production in 1992 varied between 25,000 to 40,000 tons per month, 25% being of lump type (38% of Cr2O3) and 75% being of fines. Lump is manually separated and fines are concentrated in a nearby plant. All the production goes directly to the group processing steel plants near Salvador. The Ipueira III mine is currently under some adverse economic situation because of imports from South Africa and Russia, which have better grades and sometimes a lower content of phosphorous. Consequently there has been little progress in the development of new mines and even in those currently under operation the extraction is becoming more difficult due to the lack of investment in improving mining methods and ventilation systems. In spite of such difficulties the company has backed up studies for initiating an environmental engineering investigation of the Ipueira III mine. MINING METHODS AND VENTILATION SCHEMES The mining methods adopted have changed as a function of extraction depth, rock mass strength and ore body geometry. Initially the orebody was found to be fairly continuous and dipping at about 55 degrees from surface

Jan 1, 1993

By James A. Erdman

This overview briefly describes some examples of applications and difficulties in using plants that are drawn from the literature and from field experience. Because of the generally low Au concentra¬tions found in plants, the analysis of plant tissue is critical to the successful application of the biogeochemical method of prospecting. Neutron activation analysis is the most widely used method to detect Au in plants, due largely to its sensitivity; levels in the parts per billion range are easily attained. Two general types of sampling media are used in prospecting for Au: humus and living plants. Humus has been widely used in Canada, but the sampling of plants has increased there and elsewhere in recent years. The use of douglas-fir (Paeudotsuga menziesii) at a Au-bearing stockwork in Idaho is a prime example. A maximum Au concentration of 14 ppm was detected in the wood ash of this coniferous tree, well above the normal background concentration of about 0.15 ppm. Among shrubs that might be useful in Au prospecting, sagebrush or wormwood (genus Artemisia) could be sampled because it is extremely responsive to concealed mineralization. It has been used extensively in the Soviet Union and could be used in areas of the western United States where disseminated Au occurrences might be located. Among the problems one may encounter in using plants for Au prospecting are (1) physiological barriers, by which many plant species simply do not absorb Au at detectable levels; (2) misconceptions of soil-plant correlations; (3) localization of Au in plant tissue; and (4) the variation of Au concentrations due to season. Despite these limitations, biogeochemical techniques can complement or replace other geochemical methods currently used.

Jan 1, 2013

By Ralph Loyd

One of the principal responsibilities of the California State Geologist is to provide local governments with maps and information regarding mineral resource occurrences within their jurisdiction. The primary objective of this effort is to furnish basic data that is essential in planning for and accommodating wise development of mineral deposits that are important to the economic well-being of the region, state, and nation. Local government agencies are required by law to incorporate the information provided by the State Geologist into their general plans and formulate mineral resource management policies that emphasize conservation and development of mineral deposits. The Mineral Land Classification program was initiated by the State Geologist in 1977 under authority of the California Surface Mining and Reclamation Act (SMARA). To date, about 33,000 square miles of land have been classified for mineral resource potential. Most of the mineral land mapping has been conducted in three principal areas: (1) metropolitan areas of the state where urban encroachment has greatly diminished available supplies of construction aggregate; (2) Sierra Nevada foothills, a region that is undergoing dramatic population increases; and (3) the Mojave Desert and Great Basin regions, where large Federal land withdrawals are pending that could preclude mining. Mineral land classification studies address the overall mineral potential of a region through the identification of local and regional geologic factors that control or influence the formation of mineral deposits. These studies are field-intensive surveys that enable project geologists to gain first-hand knowledge about the nature and distribution of mineral deposits in a given area and portray that information accurately in map form. This paper summarizes the progress made in the Mineral Land Classification program in the metropolitan, Sierra Nevada foothills, and the Mojave Desert/Great Basin regions of California. Selected projects from each area are discussed in detail.

Jan 1, 1995

By Dan G. Wasyluk, Meryl J. Klassen, Tony J. Morris, Clive H. MacKay

The Rogers Pass Project in British Columbia has involved the construction of two railway tunnels totalling 16.6 km and a 345 m deep shaft. Systematic geological mapping was carried out at four headings during construction. The paper discusses the procedures used to record the geology, structure, rock mass characteristics and excavation performance. Coded data from the geological mapping and shift inspector reports was entered into a computer data base. The rock mass quality was evaluated for both the Geomechanics and Q classification systems. Continuous computer generated graphic logs were produced showing the excavated perimeter map, geological parameters, installed support and construction activities. The tunnel logs were updated on daily basis and used during construction by project staff for evaluating support requirements and monitoring excavation progress. The specific requirements, difficulties and advantages in mapping tunnels using a computer based system are compared to those of a conventionally mapped tunnel excavation with hand drafted tunnel logs.

Jan 1, 1987

By Julie Mitchell

The U.S. Bureau of Mines is conducting research on the application of expert sys tens technology to mining equipment diagnostics and predictive maintenance, to increase mining productivity and efficiency. One of the greatest hindrances to mining productivity is the breakdown of equipment, causing lengthy and costly delays. A diagnostic maintenance expert system (DIMES) is being developed for the hydraulic system of a continuous coal mining machine. Through the use of such a system, the frequency of equipment failures and repair time should be significantly reduced. This paper describes the application domain, the functional requirements, and the problem approach for DIMES, the design and implement at i on of the knowledge- based system, the sensor work involved with the project, and the future plans for the continued development of this and other expert systems.

Jan 1, 1989