Search Documents

By Tetsuro Esaki

This paper describes the present condition of mining-induced damages in Japan and the characteristics of them. The change of mining operation and environmental condition has caused various significant impacts on the ground environment: subsidence, cave-in, springing out of ground water etc. The characteristics and the influences of these phenomena are discussed by investigation of the actual conditions and by fundamental studies. Some counter measures are also introduced.

Jan 1, 1989

By Naj Aziz

A series of laboratory experiments were conducted on a variety of bolt types to examine the load transfer capacities of different profiled bolts in short encapsulation push testing. A 75 mm section of 150 mm long bolt specimen was anchored in a 75 mm long stainless steel tube using full resin encapsulation. Six types of different profiled bolts and two non - profiled bolts were tested. Bolts with higher profile were in general found to have greater shearing resistance and higher stiffness than low profile bolts. Widely spaced profiles allowed greater displacement at peak shear strength, and bolts with no profiles produced very link load transfer capability. Rough surfaced plain bolts showed a significant load transfer capability in comparison to a factory supplied smooth surface bolt which supports the belief that rusted bolts have higher lnad transfer capability that un-rusted bolt surfaces.

Jan 1, 2003

By G. K. Rogers

Portals, which are the surface entrances to underground excavations, are frequently overlooked and often difficult areas In terms of ground control. Failures commonly occur In the typically high angle approach cuts and Initial subsurface portion of the portal. In order to permit rigorous design of all types of portal structures, failures are Identified and subsequently classified. Based on the failure classification and suggested analysis methodology, optimum ground and support loading can be determined.

Jan 1, 1988

By P. Palmer

Using 3D numerical modeling as a tool to predict rock behavior during mining extraction is still an uncommon practice at many underground operations. This paper will discuss how 3D numerical models were used to identify potential underground instability problems in the later stages of mining. Detailed modeling was then used to make modifications to the mine design in order to minimize the impact of the potential instability problems. This paper will also discusses how the back analysis of a previous underground collapse event at the same mine in a room and pillar area was used to identify the instability problems for a new orebody being developed deeper in the mine. A 3D numerical model was first created in the MAP3D software to determine the conditions of the pillars and the magnitude of the vertical displacement above the mining zone prior to the underground collapse. The results from the ground collapse model were then used as a threshold limit for predicting potential instabilities and developing a model for the new mining zone. sing the results from this analysis, mine management has been able to implement a much higher percentage recovery of the reserve in a new, high-grade area of the orebody while minimizing potential instabilities in the future.

Jan 1, 2005

By Michael A. Berdine

In early 1997, Twentymile Coal Company took a dramatic departure from traditional longwall recovery methods. Previously, Twentymile's standard longwall meshing procedure included the use of chain link fencing material. Beginning with the 9-Right to 8-Right longwall recovery operation, Twentymile incorporated a polyester geogrid mesh system supplied by DYWIDAG-Systems International. This paper discusses the subsequent utilization of the polyester geogrid mesh system at Twentymile.

Jan 1, 2001

By P. R. Sheorey

Four case studies of special geomining conditions from Indian coalfields are discuss- ed. These cases relate to (a) pillar extraction in two seams simultaneously under a difficult roof (Satpura I and II). (b) depillaring in an inclined seam resulting in rib instability (Sudamdih), (c) depillaring resulting in floor lift and side spalling (Jarangdih) and (d) contiguous pillar extraction under hard incavable strata. Solutions to these problems are given based on rock mechanics principles involving stress analysis, classification techniques, past experience and engineering judgement.

Jan 1, 1988

By Vasundhara

A chance detection of a seismic event of unexplained origin in the mining district of Appin in New South Wales. Australia, led to a detailed investigation of recording and analyzing seismic events occurring in the area. Multiple events were recorded each day on the seismometer stations. The larger events were strong enough to be recorded on a number of stations spread out in the district. Background investigation of seismicity stimulated due to engineering activities revealed that similar cases of mining triggered seismicity have been reported previously from many mining districts around the world. If the tectonic stresses are close to failure in a region then a small perturbation of the stress state may lead to instability in the region which may manifest itself as seismicity. The parameters that control the occurrence of such siesmicity include tectonic stress magnitudes and orientations. geological weaknesses or structural features and the amount of stress contribution due to mining. This paper reports on the seismic investigative study conducted in the Appin area and considers its association with the geological layout of the region and the mining activity.

Jan 1, 2001

Excessive roadway closure in the gateroads impedes the passage of equipment, supplies, personnel and ventilation air in longwall panels. This pager describes several factors that influence the gateroad stability and presents some measures to alleviate the problem.

Jan 1, 1994

By Buddhima Indraratna

The paper highlights the conceptual developments in rock mechanics applied to quantify the effect of bolts in the stabilization of joints and yielding soft rocks.

Jan 1, 1992

By John Stankus

Regional high horizontal stress has long been recognized as an important factor affecting roof stability However, localized high horizontal stress, although causing many ground control problems, has not received due attention, Through many ground control studies and underground experiences, it has been round that localized horizontal stress can be created by abrupt changes of overburden and stream valleys. The magnitude of localized horizontal stress depends on the valley configuration and overburden depth. Utilizing the Jennmar Finite Element Analysis System (JFEA), this paper analyzes the mechanism of the localized horizontal stress concentration based on two cast studies.

Jan 1, 1999

By Anton Sroka

The dimensioning of shaft safety zones is a substantial task of mining subsidence engineering. On the one hand, the coal reserves in shaft proximity are to be mined as complete as possible, because they can be made accessible economically. On the other hand, the maintenance of the shaft operation is to be ensured at each time, since shafts represent the most important link between underground and aboveground. Regarding these two criteria, this publication presents a model for the optimization of shaft safety zones. Beyond that, extraction methods in shaft safety zones are described, in particular with consideration of minimized mining influences on the shaft.

Jan 1, 2005

By Song Guo

This paper will present the roof bolting finite element model developed at Jennmat Corporation used to study the control mechanism of the tensioned bolt system in the laminated roof with a large horizontal stress. In addition, it will discuss general support concepts pertaining to the tensioned bolt system which are derived 6om a series of studies in conjunction with the authors' working experience and extensive research efforts over the years.

Jan 1, 1997

By A. Bortolussi

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables an tool performance (cutting rate and bead wear) has been elucidated.

Jan 1, 1992

By Clifford McCartney

The PropsetterTM System has been designed and developed to cost effectively solve problems experienced with conventional underground supports used in tailgates, headgates, bleeder entries and as supplemental supports. The PropsetterTM System utilizes the strength and orthotropic properties of timber to achieve initial stiffness and controlled yield as the roof and floor converge. Utilizing a prestressing system developed in South Africa by our parent company, the PropsetterTM prestresses/preloads the roof and floor on installation. The PropsetterTM System consists of five integrated elements which are easily assembled to achieve the objectives of ? Improved support. ? Improved safety, ? Reduced cost, ? Reduced material handling, ? Improved installation productivity, and ? Improved ventilation.

Jan 1, 1995

By André C. Zingano

The domino effect in a violent pillar collapse occurs due to the redistribution of stress in the remaining pillars near the collapse, and this stress transfer occurs in the immediate and main roofs. The remaining pillars do not have enough load capacity to support this overstress and also fail, and the domino effect propagates further to the entire panel. The domino effect does not occur only due to low load capacity of the pillars, but also the roof rock mass quality, because the stress is transferred by the roof. In high competent roof without discontinuity (fault), like massive sandstone seam, the deformation of the roof is the cause of pillar collapse extension and propagation. Depending on how close it is approaching the collapse limit; the immediate and main roofs behave differently. When it is close to the collapse limit roof convergence and pillars compression occur. Conversely when it is far from the collapse limit divergence and pillars decompression occur. This is called the arc-effect. This paper studies this behavior of the roof (immediate and main roofs) using numerical modeling to simulate the roof deformation and stress distribution in the roof and pillars. This simulation represents the progression of pillar collapse and shows the zone of convergence and divergence of the roof, and also the effect of this behavior on pillar confinement. Two-dimensional plain strain model was applied to simulate the arc-effect. The simulation results were compared to those of the instrumentation that was installed before the collapse. Keywords: pillar collapse, room and pillar, numerical modeling

Jan 1, 2005

By S. N. Zhow

China has at least 200 collieries suffering from the problem of instantaneous outbursts of coal and gas. The strong outbursts often occurred in active tectonic lanes and areas of high stress concentration. In this paper, the author describes some characteristics of the strong outbursts and analyses the effects of ground stress, gas pressure and the properties of coal in outbursts.

Jan 1, 1987

By Frank Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors using sedimentological descriptors, lead to an understanding of the mechanisms causing roof problems. Types of bedding plane features can be categorized into geometric, internal structures, bedding-plane markings, deformed bedding, solution structures, and accretionary structures. Factors such as encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described.

Jan 1, 2002

By Axel Preusse

This paper shows basic considerations about the prognosis and prediction of surface subsidence and other ground movements in the German hardcoal industry. The following case studies describe experiences collected in projects between university and industry.

Jan 1, 2000

By John C. Stankus

At the 19th International Conference on Ground Control in Mining, a paper was presented detailing new types of Jennmar INSTáL tensionable cable bolts (Stankus and Taylor, 2000). Since that time, significant testing and trials of the various types of tensionable cable bolts have been conducted. Several MSHA districts and state regulatory agencies have now approved these systems as primary support This paper will detail the use of tensionable cable bolts as primary support at two longwall mines in Virginia (MSHA District 5).

Jan 1, 2001

By S. S. Peng

To acquire knowledge on the general trend of primary and supplemental supports used in tailgates of US longwall mines a survey of 76 mines with 86 longwall panels was carried out in the summer of 1993. This paper attempts to provide some insight on most commonly used support types as primary and supplemental supports in tailgates. Analysis of the surveyed data show that fully grouted resin bolts and cribs are the most commonly used primary and supplemental supports in tailgates in longwall mines of USA.

Jan 1, 1994