Search Documents

By K. A. Dudley

Basic solvent extraction theory indicates that pH initiates the basis of an oxime's metal complex formation and therefore its selectivity toward certain metal species. The recommended optimum pH for some of the commercial copper reagents is in a range that should maximise copper loading of the oxime. However, this pH range also tends to maximise iron(III) loading under certain operational conditions resulting in low selectivity values. Recent operational parameters at Girilambone Copper Company have highlighted some of these conditions that have a major influence on the oxime's selectivity for copper over iron(III) in the leach solutions. The result is that the pH for maximum copper extraction is no longer within the optimum range to maximise oxime selectivity. Therefore, specific copper and iron(III) pH isotherms have been determined on-site for the changing leach solutions that are fed to the solvent extraction plant in order to optimise oxime selectivity. The influences of solvent extraction plant configurations are also discussed as a controlling parameter.

Jan 1, 1999

By Hong Liang-shi

Olivine lithium iron phosphate (LiFePO4) is considered as one of the most promising materials for lithium-ion secondary batteries because of its high theoretical capacity, low cost, good safety, benign environment and good cycle performance. In this paper, carbon-free and/or carbon-coated olivine lithium iron phosphate composite ultrafine powders were successfully synthesized from aqueous precursor solutions of (NH4)2Fe(SO4)2?6H2O, H3PO4 and LiOH?H2O by co-precipitation method. The obtained LiFePO4 or LiFePO4/C powders were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Their electrochemical performance was investigated in terms of cycling behavior. As confirmed by X-ray diffraction and scanning electron microscope, the material obtained by co-precipitation within the temperature range of 60ºC to 100ºC and then followed by moderate heat treatment are a single-phase olivine LiFePO4with the particle size of about 300nm. An improved carbon-coated olivine LiFePO4/C material was prepared by adding conductive carbon materials, such as glucose, activated carbon and acetylene black, into the precursor. The carbon dispersed in the materials increases the electronic conductivity of LiFePO4/C composite, and consequently, leads to high rechargeable capacity of the material. The carbon-coated material with carbon amount of 7.64%wt obtained from glucose has the first discharge capacity of 150.3mAh/g at the rate of 0.1C and 129.3mAh/g at the rate of 1.0C, respectively. After cycled for 50 times, the capacity retention rate is 95.13% at the rate of 1.0C in the voltage range of 2.5 to 4.3 V vs. Li/Li+.

Jan 1, 2006

By D. M. Hausen

The term "auriferous pyrite" relates to an association of gold with pyrite in a variety of textural forms that affect metallurgical treatment. Extraction of the gold depends not only on the grain size and distribution of the gold in the pyrite, but also on the crystal size and surface area of the pyrite. Occlusions of medium to coarse gold may be liberated by moderately fine grinding. The amenability of finely dispersed (submicroscopic) gold depends in part on the activity of the pyrite surface for oxidation. Two types of auriferous pyrite at Carlin, Nevada, have been examined by optical microscopy and SEM methods before and after aqueous oxidation test work to show how differences in morphological features can affect rates of oxidation and amenability to gold extractions by methods of chlorination and low temperature oxidation.

Jan 1, 1981

By Uchil Jayagopal, M. Krishna, P .. V. Krilpakara, S. Manjunath

"There have been a pioneering efforts over the last forty years in the development of metal matrix composites (MMCs) as a new engineering materials, having improved properties, light weight characteristics and competitive costs compared to traditional materials. Following recent advancements in casting technology and the use of melt stirring device by foundries, discontinuously reinforced MMCs where prominent alloys are reinforced with particulates or short fibres and the being employed ·in the production of castings targeted for automotive and aerospace application.The ZA-27 alloy has a high strength compared to zinc or alluminium alloys with a lower melting temperature. The main objective of the present research is to study the effect of quartz particles on the mechanical behaviour of ZA-27 alloy composites. The results showed that the ultimate tensile strength, hardness, Young's modulus of the composite gradually increased with increase in the weight percentage of the quartz reinforcement. However overall ductility decreased with an increase in quartz reinforcementIntroductionMetal matrix composite (MMCs) offer outstanding benefits as they combine metallic properties with ceramic properties there by yielding improved physical and mechanical properties.1Among the various type of MMCs particulate reinforced composite are the most versatile and economical2. By suitable choice of metal matrix and particulate system a wide range of properties combination can be obtained such as strength, modulus, fiiction.al resistance, tribological performance and machinability. These composites are capable of replacing conventional alloys in a considerable range of applications. They also offer significant saving in energy and resources"

Jan 1, 2000

By Thomas E. P. Wechsler

The limiting factor for most pyro-metallurgical processes in secondary cop- per melting is the time required to heat and melt the product. American Combustion's proprietary PYRETRON variable £uel/air/oxygen combustion system improves the throughput of existing scrap melting and heating furnaces for copper and copper alloy production by increasing the rate of heat transfer from the flame to the product. The increased productivity and energy savings obtained from this technology can result in sizable reductions in operating costs for smelting operations.

Jan 1, 1991

By Daniel Adolfsson, Ryan Robinson, Fenwei Su, Jelena Blagojevic

"Cold bonded briquetting of steel plant by-products has proven to be a viable recycling alternative concerning technology, economy and environment in both the traditional blast furnace route and the direct reduction process. A critical parameter in cold bonded briquettes is the type and amount of binder used during production. The binder material must meet certain quality requirements concerning low and high temperature strength, chemistry and economy. Currently, SSAB Tunnplåt uses ordinary Portland cement (OPC) as binder in their cold bonded briquettes. In order to improve binder quality and possibly decrease OPC dependency, a binder feasibility study has been conducted concerning an internal by-product, ladle slag, as a supplement and/or partial substitute for OPC. Several characterization techniques have been used to study the behaviour of ladle slag, these include: XRD, XRF, SEM, glass content analysis, calorimetric analysis, particle size distribution and thermochemical stability considerations concerning the CaO-Al2O3-SiO2 system.IntroductionRecently, a project was initiated at SSAB Tunnplåt AB, in Sweden, which aimed at reducing the amount of ordinary Portland cement (OPC) as hydraulic binder in cold bonded briquettes by partly replacing it with ladle slag. OPC is traditionally used within civil engineering, and widely accepted as a hydraulic binder in a number of different applications. OPC consists of four major crystalline phases, i.e. C3S, C2S, C3A and C4AF. Tricalcium aluminate as well as the ferrite phase in OPC reacts very quickly with water, for this reason gypsum is added to the clinker in order to retard these reactions. The fact that gypsum is present in the system limits the recycling of briquettes to the BOF, since the presence of gypsum during steelmaking results in a significant amount of sulphur emissions. The latter along with the expense that follows, makes it worthwhile to consider alternatives for OPC as binder in cold bonded briquettes."

Jan 1, 2008

By Valdeci Paula Alvarenga, Sergio Luiz Costa, Itavahn Alves da Silva, Filipe Bueno Carvalho, Varadarajan Seshadri, Carlos Antonio da Silva

Use of fluorspar in steel refining operations is one of the environmental concerns and as such reduced consumption of this material or substitution of the same is one of the objectives. Industrial runs were carried out at Aperam Steel making convertor unit (Timóteo, MG, Brazil) using recycled/briquetted slag for partial or complete substitution of fluorspar. Samples were collected from the metal bath and slag after oxygen blowing to assess dephosphorization with several combinations of recycled/briquetted slag and fluorspar. The results showed that partial substitution of fluorspar by BOF slag briquettes did not affect the efficiency of dephosphorization. In general average Phosphorus content was reduced to 0.010% in the case of partial substitution compared to 0.016% in the regular refining procedure with no substitution. This replacement also resulted in 40% reduction of the fluorspar consumption in the converter

Jan 1, 2015

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

By Yuanbo Zhang, Bingbing Liu, Zhuyin Chen, Xiao Kang, Chen Liu

Composite agglomeration process (CAP) is an effective method to utilize the iron-bearing dusts generated in the ironmaking plants, by which the dust percentage in the sinter feed can be increased up to 20 wt %. In the current study, a comparison on behavior of iron-bearing dust in the conventional sintering process (CSP) and CAP was characterized. The results showed, in the CSP products, the scattered iron-bearing dust in the mixture was disadvantageous for the sintering indexes and consolidation of the finished sinters. In the CAP products, the main phase in the iron-bearing dust pellets was well-crystallized Fe2O3 grain particles. In the matrix parts, there were more Fe3O4 particles generated, which caused to high RDI+3.15 and low RI of the finished products. The pellets and the matrix parts were bonded by iron oxides and acicular calcium ferrite.

Jan 1, 2016

By J. Rastas

The recovery of lead, silver and gold from existing and potential zinc process residues using a sulfidization-flotation method was investigated on a laboratory scale. The following residues were tested: neutral leach residue, high acid leach residue, and hematite residues. The sulfidization of lead and silver is carried out at low pH by the addition of a stoichiometric amount of sulfide at a controlled rate. To increase the particle size of the sulfides, seeding with synthetic lead and silver sulfides -is employed. The flotation is carried out at pH 2-4 using low pH-collectors such as dithiophosphates and dithiophosphinates. Special attention must be paid to the role of oxygen in the conditioning stage. The effect of different parameters on both the sulfidization and the flotation has been evaluated. Recoveries of 85-90, 90-95 and about 80 % were obtained for lead, silver and gold, respectively. Typically, concentrates containing 50-60 % lead, 3-5 kg/t silver and 10-15 git gold were produced.

Jan 1, 1990

By Yuanbing Ling

Keywords: Calcium sulfate, Sulfuric acid, Phase transformations, Thermodynamic analysis As part of a boarder research project, seeking the development of a cost-effective process for direct production of the high value material, -calcium sulfate hemihydrate, from sulfuric acid at atmospheric as opposed to elevated pressure conditions, the fundamental work presented here has been undertaken. This includes experimental monitoring of phase transformation reactions and thermodynamic analysis of the relationships among the various phases, namely, calcium sulfate dihydrate, hemihydrate and anhydrite in aqueous sulfuric acid solution at temperatures ranging from 20oC to boiling point.

Jan 1, 2004

By W. G. Davenport

The Cu content of industrial flash furnace concentrates varies considerably. It is usually around 30% Cu (Tables 2.1, 3.1) but it may be as high as 55% Cu and as low as 20% Cu. The mineralogy of flash furnace concentrates also varies. The most common Cu mineral is chalcopyrite (CuFeSz), but many concentrates contain bornite (CuSFeS4), chalcocite (CU2S), covellite (CuS) and even native copper (CUO). Pyrite (FeSz) :is also present in many concentrates. This chapter examines how concentrate composition affects flash smelting -with specific reference to 'low-Cu-grade' FeS2-CuFeSz concentrates. Chapter 14 does the same with 'high-Cu-grade' CuzS-CuFeSz?concentrates.

Jan 1, 2001

By M. Vondersaar, B. Bulnes

Quemetco, Inc.,. as a subsidiary of RSR Corporation, operates one of RSR's three secondary lead smelters in the City of Industry, California, next to a residential area within Los Angeles County. The Reverberatory furnace serves as the main reactor for melting lead grid and paste recovered by the battery crushing system. Feed material is introduced via screw conveyor after drying in an upstream rotary kiln. Slag produced by the Reverb flows directly to an electric arc furnace. Products from this one-pass furnace system consist of soft lead bullion from the reverb, hard lead bullion from the arc furnace, and a non-hazardous slag from the arc furnace. Furnace bullion is processed into finished product in a six-kettle refinery. An overview ·of plant operations is presented. Where applicable, references will be made to changes that have taken place during the last decade.

Jan 1, 2000

By Zhucheng Huang, Lingyun Yi, Bin Chai, Tao Jiang

"A high iron content manganese ore was reduced at 900~1200°C and followed by a magnetic separation process. SEM and EDS analyzes were employed to examine the transformation of microstructure and phase in reduced sample and the mechanism was revealed. Results showed that elements enriched during reduction. Iron existed in the metal iron phase and most of oxygen formed compound with manganese. Consequently a clear distinguish between iron phase and manganese minerals formed, which was beneficial to the separation of iron and manganese. But the iron phase can not be monomer dissociation in grinding process and manganese compounds turned into magnetic product as package and mechanic inclusion due to the isomorphism of iron and manganese and the small particle size. And MnO could be found partially in iron phase, which hindered the further separation of manganese and iron.IntroductionManganese is widely used in industry. The amount of manganese used in steel industry is very huge and 90% manganese is used in steel industry. Manganese ore resources are rich in China, yet with fewer rich ore but more low-grade ore which accounts for 93.6% and fine refractory ore. The constitution of the ore is very complex and more than 73% of all the manganese ore contains iron[l,2]. With the increasing of consumption of steel, the demand for manganese is becoming larger and larger and the imported ore accounts for more than 50%. Therefore, how to use the manganese ore efficiently has very significant meaning. The main method is manganese residual, which is simple and stable. However, the development of the method is limited by the quality of manganese ore, the huge amount of manganese residual, the technology of blast furnace process and economics[3,4]. Chemical benefication which may pollute environment and is difficult to recover iron is still being researched[5,6]. The paper investigated the process in which anthracite coal was the reducing agent for coal-based direct reduction and magnetic separation of the ore, and SEM with EDS measurements were employed to examine the transformation of phase in reduced sample and the mechanism was revealed[7,8]."

Jan 1, 2013

By Luciano E. Ramírez, Jesús L. Valenzuela, José R. Parga

"An innovative process for removing copper cyanide complexes including silver and zinc from cyanidation circuits has been developed. The technology was based on the inducing the nucleated precipitation of copper and silver in a tube serpentine reactor, using sodium sulfide as the precipitate and sulfuric acid as pH control. The results showed that pH had a great effect on copper cyanide removal efficiency and the optimum pH was about 3 to 3.5. At this pH value copper cyanide removal efficiency could be achieved above 97 and 99 % ,when influent copper concentration ions were 650 and 900 ppm respectively. In this process (sulphidizaton-acidification-recycle-thickening), the cyanide associated with the copper cyanide complexes is released as HCN gas under weakly acidic conditions, allowing it to be recycled back to the cyanidation process as free cyanide. This system was successfully commercial applied at Minera William in Mexico.IntroductionThe recovery of gold and silver from minerals and concentrates with cyanide is an important hydrometallurgical process, which has been studied for more than 124 years. Patented by MacArthur in 1888 [1], the process relies on the fact that gold dissolves in aerated cyanide solutions to produce the gold cyanide complex. The stoichiometry by wich this reaction occurs is known as the Elsner equation as shown here. Silver is accomplished in the same fashion."

Jan 1, 2012

By Neale R. Neelameggham

"Most chemical process plants and metallurgical production facilities have some sort of cogeneration to minimize process energy costs. Use of Alternative Energy Production from sun and wind power with storage can become an integral part of a process plant utility. This will facilitate reduced fossil fuel usage and help minimize thermal emissions. This will be similar to Pollution Control equipment, which have become an essential part of process plants in the past four decades. Conceptual flow sheets of such Process Utility schemes are presented.IntroductionPower is supplied to industries, commercial and residential users. Over the past decade, Electric Utility companies have made major inroads, in introducing alternative energy resources in an attempt to somewhat reduce fossil fuel use in power generation. Now, on a much larger scale than in the early 1980s, residential users, motivated by government provided tax credits, have started installing alternative energy generators such as roof top wind mills or roof-top photovoltaic generators. This will minimize future energy costs, help control thermal emissions etc. This alternative power generation is typically connected to the existing power grid with two way power metering. However, the use of alternative energy generation has not been seen at large industrial sites yet.Paul Scherer Institute, Switzerland and the NREL laboratories in Colorado, are two of the several institutes which have been developing how solar thermal power can be used to supply the endothermic input energy in chemical and metallurgical processes. The theme of this present symposium addresses the above as well as the energy storage needs for such events to become continuous. This paper emphasizes the concept of how alternate energy can be used in the production of materials on a generic sense wherever there is a need for input energy – beyond endothermic process energy - while addressing how to reduce the thermal and carbon emissions.The alternative energy generation using wind or solar source is discontinuous due to the nature of the energy source. They are not only discontinuous but also variable. This necessitates storage of generated power for close to continuous use with variable loads. C Smith, et al pointed out in 2006, that 'the electric power industry has taken notice of the expansion of wind and its potential' in a summary article on integrating wind generation into utility systems.1 In 2009, the 1000 MW wind generation project in Texas had to be postponed to 2013 for lack of transmission.2 There are only a few large MW solar generation units in the US; the projects being slow mainly from lack of adequate storage and redistribution."

Jan 1, 2010

By I. Gaballah

The chalcopyrite ore's anodic and cathodic electrodissolution are studied using a Porous Pulsed Percolated Electrode (3PE) reactor. Stationary solid electrode experiments are also performed to explore the mechanism of electrochemical dissolution of chalcopyrite. Experiments with a low - grade natural ore have been carried out at 25 "C in solutions containing 1 M NaCl and 1 M HCl. Galvanostatic and potentiostatic conditions are employed. The influences of current and potential on selectivity of the chalcopyrite ore dissolution are assessed. Anodic oxidation of this ore leads to a preferential dissolution of iron bearing minerals, whereas cathodic reduction is more selective with respect to chalcopyrite. However, in both cases the electrochemical dissolution is incomplete and the current efficiency is low. Design of the actual reactor has to be modified to increase the bed conductivity and to allow continuous experimentations.

Jan 1, 1994

By Denise C. R. Espinosa

Rechargeable lithium batteries are one of the most promISIng technology in battery development. Although Li ion batteries have been used as an alternative to the more polluting and less performing Ni-Cd batteries, Li ion batteries have limited life and their disposal is uncertain. It is imperative that valuables from wastes, such as lithium, should be recovered. The main objective of the present work was to characterize secondary lithium batteries for cellular phones. This was done using unit operations of mining processing, x-ray diffraction (XRD), chemical analyses and the rmogravimetric analysis (TG). The unit operations were hammer mill grinding, knife mill grinding, size separation and magnetic separation. After the hammer grinding process, the plastic cases were almost intact, however, they have released the cylindrical lithium batteries themselves and these parts correspond to 70% of the total battery weight.

Jan 1, 2001

By W. G. Davenport

A flash furnace can be run many different ways. It can, for example, be operated with: (a) highly 02"enriched, ambient temperature blast and no fossil fuel (b) considerable fossil fuel and hot, slightly Or enriched blast. It can also produce different grades of matte. With all these possibilities, the flash furnace operator can benefit from any technique that will indicate the 'best' way to operate his furnace. One such technique is Excel's 'Solver'optimizationroutine#. This chapter shows how our matrices and Excers optimization.abllity can be used to optimize a flash furnace operation. The chapter sets three optimization goals: (a) minimum industrial oxygen + oil cost, $ per tonne of concentrate (b) maximum smelting rate, tonnes of concentrate per hour (c) maximum profit, $ per hour.

Jan 1, 2001

By Sang Han Son

The vapor pressures of FeCL2 and ZnCL2 in the FeCL2?ZnCL2 system were measured by the transpiration method at 873K and 9I7K, The vapor pressure data were interpreted to indicate the formation of complex ions in the FeCL2?ZnCL2 melts, It is presumed that the complex molecule FeZnCl4 as well as FeCL2 and ZnCL2 exists in the vapors in equilibrium with molten FeCL2-ZnCL2 mixtures, The activities in the FeCL2-ZnCL2 system are shown a negative deviation from Raoult's law. These results suggest the formation of complex ions such as ZnCL14 in molten FeCI2?ZnCL2 mixtures.

Jan 1, 2003