Search Documents

By Okechukwu Anopuo, Gerhard Tober, Petra Maier

"In this study, an investigation on the microstructure of hot rolled steel S355J2+N was conducted to optimize process parameters of complex forming, which combines rolling and bending. The best sets of parameters are worked out based on homogeneous mechanical properties and microstructure within the varied deformation degree with maximum at <p = 1.14 on a 25 mm thick plates. Mechanical properties, especially of heavy plates, are strongly influenced by the local deformation degree, strain rate and temperature. Detailed microstructural analyses showed that the ferrite-pearlite band structure changes near the surface, while maintaining homogeneous microstructure within the deformed work piece. Surface decarburization was also observed and this leads to decrease in hardness. To minimize iron oxide formation which could lead to side cracking, reduction in exposure time to temperature was suggested. On the other hand, temperature reduction below a critical value would risk the accurate forming process.IntroductionThis work presents the preliminary results of research to develop a new complex deformation process of thick steel plates. Complexity is given because the forming process combines rolling to reduce thickness and profiling by bending. The work piece will experience a thickness reduction from 25mm to 8 mm and is double curved. To explain and understand forming of thick plates basics of sheet forming as well as massive forming need to be used. At the moment there is no forming process established to produce double curved plates including reducing thickness in one process step. Technologies nowadays consist of two process steps: flat rolling and pressing in shape. Due to good weldability and formability the final product will be made of steel S355J2+N. This low-carbon steel is well understood and has a low strengthening exponent, which is expected to keep the forming forces down. Reduction of thickness from 25 mm to 8 mm gives furthermore a high deformation degree. Thus, hot forming has to be applied. The determination of process parameters is the main aim of overall research project; temperatures above lOOO°C are expected. Flow curves in literature are given at various temperatures and strain rates [1]. However, experiments with data close to the industrial application are rarely found, especially at low strain rates and high deformation degrees. Pre-test were done by flat rolling, being aware that the influence of bending is eliminated. The microstructure evolution were characterised in relationship to material formability with special attention to grain size change and recrystallization. Representative samples should be selected from specific locations in the deformation zone according to the knowledge about the metal forming process [2]. Due to no further alloying elements in S355, no precipitation hardening is expected to take place during hot forming, which keeps the mechanisms simple and the concentration on the feasibility of the complex forming process is given."

Jan 1, 2012

By Goran Vukovic

The use of gas purging plugs in the copper industry is a widely used practice. They provide substantial improvements especially in anode refining furnaces, where savings in process time and energy are obtained as well as refractory wear and buildups inside the furnace are minimized. The newly developed system, enables purging plugs to be implemented in both stationary and tilting furnaces, is in operation in vessels on three continents. An additional advantage in these furnaces above all other benefits is the significantly improved melting rate. This innovative and patented gas purging system consists of a purging plug cooling device and a slidable, cooled piping system. It provides compensation for any thermal expansion in the furnace lining and minimizes the risk of undesirable copper infiltration. User experiences and results of this widely used system are reported in this paper.

Jan 1, 2014

By Ryosuke O. Suzuki

A new cell concept for calciothermic reduction is proposed in which the titanium dioxide instead of TiCl4 is used as the raw material for reduction, Metallic calcium is needed as the reductant of a thermochemicaily stable oxide, such as TiO2. CaCl2, is selected as the solvent of Ca and simultaneously as the solvent of CaO. The reduction system consists of a single cell where both the reduction reaction and the electrolytic reaction for recovery of reducing agent coexist in the same molten CaCl2 bath. A few mol%Ca dissolves in the melt and gives the media a strong reducing power. Sufficiently deoxidized metallic titanium deposits and forms a slightly sintered granular sponge. Both mechanisms of the halide flux deoxidation and the electrochemical deoxidation work efficiently for these fine precipitates, The reducing agent is in situ recovered by electrolysis of CaO because the molten CaCl2 he a relatively large solubility for CaO Some cell designs and modifications are proposed for industrial applications.

Jan 1, 2003

By Fumitaka Tsukihashi

Increasing amounts of steel scrap are being used as resources for steelmaking. Therefore. there has been a growing interest in the removal of handful tramp elements such as antimony, zinc, tin, arsenic, bismuth, lead and copper from the molten steel. The problem that should be solved is the economic removal treatment of residual tramp elements in the steelmaking processes and the production of high quality steel by reducing the effect of the contaminated tramp clements and satisfying the environmental regulations. In this paper, the available thennodynamic data of the residual tramp elements in the molten steel are summarized and the possibility of the removal of residual tramp elements from the molten steel is thcnnodynamieally estimated.

Jan 1, 2003

By J. P. Evans

The modem &apos;copper smelter today utilizes tonnage oxygen for smelting concentrates. ,generating a high strength S02 off-gas leaving the smelter vessel. This gas stream. which also contains any unreacted oxygen, plus CO2; N2 and H20. also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates, The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals, in the off-gas circuit. Depending on this history. the type and characteristics of the chemical and physical reactions which occur in the gas handling system &apos;can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries and design. on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data. several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By Flávia Paulucci Cianga Silvas, Otávio da Fonseca Martins Gomes, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Guilherme Apostólico Bortolini, Stoyan Gaydardzhiev

"Printed circuit boards (PCB) are particularly problematic to recycle because of the heterogeneous mix of organic materials, metals, and glass fiber. PCBs are found in almost every electroelectronic equipment and their recycling process involves a pre-treatment to separate the products which contain targeted metals. In this work, a physical processing involving sequential shredding and hanuner milling were used to obtain a comminuted sample from scrap printers PCBs. The thus prepared sample was analyzed for particle size distribution and by optical microscopy as well was subjected to pyrolysis, leachabilty and chemical composition determination by XRF. The metals concentration was determined by ICP and AAS. The PCBs have been also analyzed by SEM-EDS (micro-analysis and X-ray mapping). The results show that the studied PCBs are lead free, multilayer with 4 copper layers, have 45% of metals and the copper is present in significantly higher concentration than the rest of the metals.IntroductionThe global generation of e-waste (electrical and electronic equipment waste - WEEEs) grows at a rate of about 40 millions of tons per year [ l].Among this e-waste there are PCBs that are present in almost all electronic equipment. Their composition is heterogeneous and varies according to several factors, including: kind of EEE, when and where it was produced, fabrication technology [2], etc. In printers, the PCBs represent about 6.6- 8 wt.% [3].The PCBs treatment may include physical, pyrometallurgical, hydrometallurgical, ectrometallurgical and more recently bio-hydrometallurgical process. Normally there is a combination between these processes [2, 4, 5, 6, 7, 8, 9, 10].The diversity between the different PCBs composition complicates the recycling process since the composition of metal and others materials can vary according to the models. So characterization is an indispensable step before any processing of PCB to begin. Owing to the above said, the main goal of this work has been set to characterize representative samples of PCBs from printers through physical, chemical and microstructural analyses."

Jan 1, 2014

By L. I. Rosato

A novel hydrometallurgical process for the recovery of silver and gold from neutral leach residue that is based upon leaching with thiourea, is described. Laboratory and pilot plant studies have shown that 80-90% of the silver and 60-70% of the gold can be recovered by:? ( i) leaching zinc calcine with &apos;Spent electrolyte at pH 2.0-3.0 to generate a precious metal-bearing zinc ferrite residue, (ii) leaching of the thickened zinc ferrite with 3-5 g/L thiourea in a six stage carbon-in-pulp circuit, (iii) elution of silver and gold from the loaded carbon with a thiourea- butanol solution, (iv) thermal regeneration of the stripped carbon and (v) recovery of the precious metals from the pregnant eluate by cementation with zinc dust. The reasons for adopting the thiourea CIP leach and the preferred operating parameters for each process step are presented. The requirements for the destruction of any thiourea transferred to the zinc circuit are outlined, and the results of an integrated one tonne/day pilot plant operation at Canadian Electrolytic Zinc are given.

Jan 1, 1990

By A. H. Castillejos E., F. A. Acosta G.

Filtration is widely used as a terminal refining step for metals, particularly for the casting of aluminum alloys, but still more knowledge is required to understand how several factors affect the efficiency of removal of inclusions. In this study, both, initial and long term filtration efficiencies of a ceramic foam filter have been obtained from the computed trajectories of solid particles suspended in molten aluminum. The complex structure of the foam filters is represented by a unit cell which is formed by a pair of pores with average dimensions. The fluid flow field was determined from the numerical solution of the Navier-Stokes equation, and periodic fully developed flow was assumed at the inlet of the calculation domain, as a boundary condition. This flow field corresponds to laminar flow as that found in ceramic filters operating under normal conditions. Computed initial filtration efficiencies showed that filtration efficiency decreases sharply with fluid velocity for particles larger than 30 µm, but smaller particles are better trapped at higher fluid velocities. Finally, it was found that long term filtration efficiency for particles of 8 µm decreased with time, in spite that perfect particle-wall attachment was assumed. Filter aging was considered in this study, and it was found that the distorted flow field, around the already trapped small inclusions prevented further collection.

Jan 1, 1999

By Fuming Wang, Xin Lu, Hao Bai, Hebin Zhu

"In this study, CO2 emissions and carbon footprint of a typical steel works with integrated process and iron and steel industry in China was calculated and analyzed by a carbon footprint method based on the model of process CO2 emissions in iron and steel making. The carbon footprint of iron and steel industry from 1991 to 2010 in China showed a rapid increasing tendency. In 2008, the CO2 emissions of iron and steel industry in China was 1.289 billion tons, 19.71% of the national total CO2 emissions, and the corresponding carbon footprint was 159.13 million hm2 of green area. Carbon deficit of iron and steel industry also go up gradually if considering the carbon storage by green vegetation. Thus, the internal carbon reduction strategy, such as energy structure optimization and energy saving technology, was mainly encouraged for the sustainable development of iron and steel industry in China.IntroductionThe Global Warming resulting from the increase of Greenhouse Gases (GHGs), in particularly CO2, in the atmosphere has become the main reason of global climate change, and large emission reductions are required for sustainable development [ 1]. The iron and steel industry is the largest energy consuming manufacturing [2] in the world and the largest emitter of CO2 emissions. In 2005, it accounted for about 20% of global industrial energy use and 30% of energy and process CO2 emissions from industry [3]. In China, the crude steel has firmly been ranking at first of the world recent years and kept growing tendency year by year. With the production growth, the CO2 emissions of iron and steel industry also increased significantly and hence the steel industry has become one of the most sources of CO2 emission in China [4], which has attracted more and more attention to seek the carbon reduction strategies.Carbon footprint is an important and useful concept originating from Ecological Footprint, which was used efficiently to quantitatively analyze the impact of the human activities on ecological system, in particularly impact of the human energy activities [5]. In the view of Life Cycle, the carbon footprint is efficient to analyze the direct and indirect CO2 emission in the whole life of various products used in human activities. As to the iron and steel, the important materials and products in the human life, the carbon footprint analysis is quite necessary to evaluate the CO2 emission impact on the corresponding ecological system and global environmental."

Jan 1, 2013

By Robert Vidal

The performance of a laboratory-scale cell for the electrolysis of an aqueous chrome alum solution was studied. Electrode potentials, pH, and Eh were recorded. An optimum catholyte pH of about 2.5, consistent with information from the literature was observed. Values exceeding this range resulted in a precipitate formation and are detected by wavering cathode potentials. The role of anodically produced dichromate ions was investigated by chemical analysis. It was found that the steady state concentration of dichromate ions varies inversely with fluid flow from catholyte to anolyte. This concentration was also reduced with the use of precious metal coated titanium anodes.

Jan 1, 1994

By Derek J. Fray

"In order to extend the application of fused salts in\the electrowinning and electrorefining of metals, it is necessary to maximise the current density, minimise the voltage drop and greatly increase the area of electrode surface so as to compete with the space-time yield of pyrometallurgical reactions. The various designs of electrowinning cell are reviewed and it is shown that by the application of a modest centrifugal field it is possible to reduce the anode to cathode interelectrode spacing to 4 mm whilst still maintaining a current efficiency of 85-90%.The thermodynamic potential for electrorefining is far less than for electrowinning yet fused salt electrorefining is only applied in limited cases. The reasons for this are discussed and the important design parameters evaluated. It is concluded that by using packed bed electrodes, separated by a diaphragm, the possibility of electrorefining with very low energy consumption can be achieved. Carbothermically-produced metals are always cheaper than those produced by electrolysis but suffer from the disadvantage of low purity. It is proposed that fused salt electrorefining may offer an energy efficient way of upgrading the metal. IntroductionThe majority of metals can be deposited from fused salts (1,2) but as commercial production is restricted to the more reactive elements, it is worthwhile considering the advantages and disadvantages of fused salt electrolysis as' compared to smelting and aqueous electrolysis. The advantages over aqueous extraction are as follows:1) the much higher conductivities and diffusivities result in much lower IR losses and higher current densities can be achieved at modest voltages;2) the elevated temperatures of operation result in larger exchange currents which give rapid kinetics and lower activation polarisation for the electrode reactions;3) the absence of water as a solvent means that it is not necessary to consider the evolution of hydrogen as a competing cathodic reaction. Furthermore, alkali halide salts, often used as solvents in fused salt electrolytes, have high deposition potentials;4) molten salts generally are mutually soluble and, therefore, concentration polarisation effects are minimised."

Jan 1, 1988

By R. R. Odle

A laboratory and pilot-scale investigation of direct smelting of copper concentrates was conducted to determine the effect of concentrate analysis and the degree of roasting on the yield and quality of copper produced in a subsequent smelting step. A stoichiometric :mOdel of direct smelting is presented which predicts the? quantity of copper; slag, and white metal&apos; prOduced&apos;and the distribution of copper in these phases as a function? of the concentrate &apos;(calcine) analysis.

Jan 1, 1983

By Jie Li, Zhongliang Tian, Xun Hu, Kai Zhang, Yanqing Lai, Hongliang Zhang

The Al-Sc Alloys show many advanced properties for a wide range of engineering applications. But the metal Sc must be added into the metal Al in the form of the Al-Sc master alloy, which is usually produced by the thermal reduction process. In this paper, the decomposition voltages of Sc2O3 and Al2O3 in Na3AlF6-K3AlF6-AlF3 melt were calculated based on the Nernst equation. And the Al-Sc master alloy was prepared in the melt at 950°C by electrolysis. The results show that the Al-Sc master alloy can be prepared by the co-deposition of Sc3+ and Al3+ at the cathode if the concentration ratio of Sc2O3 to Al2O3 in the melt is more than 2:1 under the condition of the aluminum electrolysis. SEM and ICP analysis of the product indicates that the Al-Sc master alloy is made of the phase Al and the phase Al3Sc.

Jan 1, 2016

By David M. Davidson

Seven intrusive phases have been mapped to date in the 1 b.y. Red Bluff Granite Complex (RBGC) near El Paso, Texas. This batholith is 20 km2 in area and intrudes older supracrustal units as well as a trachyte ignimbrite cap. Two early microgranite sills are spatially separated 6 km from a porphyritic, three-phase "ring complex" by a tin-bearing, biotite granite which cores the RBGC. These units are intruded, in turn, by a riebeckite granite which locally exhibits lineated and pegmatitic textures as well as exceptionally high light REE and Zr values (800 ppm La; 3,000 ppm Zr). The riebeckite granite is exposed in three separate occurrences within the Franklin Mountains. REE values in the RBGC are depleted in HREE and show distinct negative Eu anomalies. Typical La/Yb ratios are 5:1-2:1 with Eu values ranging from 10-80 ppm. The mineral source of the high REE values in the riebeckite granite has not yet been specifically identified, but is believed to be zircon.

Jan 1, 1988

By Chunlin Chen

Nickel-sulfide minerals are normally associated with copper and iron sulfides and often contain a minor amount of valuable metals such as cobalt and detrimental impurities such as arsenic. Metal losses in slag vary from process to process during the pyrometallurgical production of nickel and, depend on the feed composition, slag chemistry and operating conditions. Maximiz the metal recovery is one of major considerations to optimize operating condition for nickel smelting/ converting processes. At the same time, the deportment of minor elements between various phases during nickel smelting is of great importance by smelter operators. The Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems [1]. Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature systems. The sulfide smelting module of the MPE, which covers the minor elements such as As, Bi, Sb, Pb, Se, Te, Sn, Co and Zn, is capable of modeling the deportment of major and minor elements between various phases during nickel smelting. In this article the application of the MPE model in modelling the nickel smelting process is presented. The modelling results on the majors and minors are compared with the plant data. The deportment behaviour of arsenic in nickel smelting was analysed and the impact of slag chemistry on slag properties was modelled. These results can assist process metallurgists in exploring the optimum fluxing strategy for smooth operation and the potential practices for improving arsenic removal.

By Joseph Goodwill

1. PURPOSE The objective of this paper is to summarize a study undertaken by the EPRI Center for Metals Production (CMP). The overall purpose of the study was to identify electrolytic opportunities that might merit consideration for joint development by industry and EPRI. 2. SCOPE The electrolytic technologies of interest to this study include: Electrorefining, Electrowinning, and Fused-salt electrolysis. Recovery from primary, secondary, and waste materials were included in this effort; however, we excluded from consideration: Plating and coating operations, such as electrogalvanizing; Mining and milling operations in which electric energy is predominantly used for comminution; Electrothermal processes in which submerged-arc, open electric-arc, and plasma-based smelting processes use electric energy largely to provide a melting or refining ("heating") capability; and Aluminum electrotechnologies since these were the subject of a separate study (CMP 86-2). We recognize that there may be some "gray areas" between these excluded areas and the electrolytic sectors of interest. For this reason, a secondary criterium was used, namely, if the major use of electric energy was to extract or refine the

Jan 1, 1990

By William Petruk

The capabilities of SEM/image analyzers for determining quantitative mineral data which have a bearing on extractive metallurgy have given applied mineralogy a new dimension. The capabilities include automatic mineral identification, unattended operation, search for rare minerals, and measurements of (1) mineral quantities, (2) grain and particle size distributions, (3) liberation characteristics of minerals in ground ores, and (4) mineral associations. Data on mineral quantities define the distributions of elements among minerals, provide background information on characteristics of the samples, and provide a data base for a mineral-materials balance. Size analysis data of the minerals in unbroken ores are used to predict the grind required to liberate minerals. Data on liberation analysis can be used in many ways. One application is to process the image analysis data for feed, concentrate and tails by a materials balancing technique to calculate the recovery of liberated and unliberated grains at each point in a circuit. The calculated recovery data define the behaviour of an ore in a concentrator, pilot plant or bench test, and indicate whether recovery improvements are possible and/or feasible for a particular ore.

Jan 1, 1991

By J. A. Bakken

Thermal plasmas are interesting for a wide range of metallurgical and chemical processing applications. The 300 kW experimental reactor PRESS, which has been in use since 1987, is operated in the transferred arc mode with three or one plasma torches . Tests include remelting of silicon fines and production of ultrafine silica. Work on a novel three stage process for production of silicon metal is under way. A 1:1 model of the plasma reactor is used to measure the wall heat flux distribution calorimetrically. The cold walls of this model are divided into several water-cooled sections. The same plasma torches as in the real hot-wall reactor are used. In parallel to the experiments and calorimetric measurements theoretical work is done on numerical modelling of one and three transferred arcs. A modified version of the flow simulation program FLUENT from Creare Ltd. is used.

Jan 1, 1991

By K. Yamada, T. Takaoka, A. Ozeki, M. Yamaga, Y. Kawai, S. Nishioka, Y. Kikuchi

"Recently, smelting reduction of chromium ore in BOF has been actively investigated as a key unit process for an innovative future stainless steelmaking. The prominent feature of this new process route is energy and process saving, and production cost saving. The development is already in the midst of application to the commercial production, however there still remain the following key technologies to be established for the full use of the process. One is a speed up of the reduction of chromium ore to match with sequential continuous casting, and the other is efficient combustion of carbonaceous materials in BOF to reduce their consumption, and hence to assure the steel quality. High degree of post combustion technology and new charging technology, i.e., ore-coal-flux-oxygen mixed injection, could be effective for those two subjects. In 2000 or beyond, the new process would have become quite popular owing to the establishment of those key technologies.Introduction Since stainless steel was invented, its production has continued to expand because of its attractive combinations of functions of excellent corrosion resistance, good formability, a pleasing appearance, and a wide range of strength levels. New types of stainless steels as well as new applications are continually being developed.Compared to the production of ordinary steels (1), stainless steel production (2,3) shows steady growth worldwide, while the former production remains on the same level, as Figure 1 shows. It can be estimated that future production would show further growth since materials consumer demands are more fashionable, or more functional, which could be satisfied by stainless steels.Thus market needs would be met, if it could be produced with reasonable production cost. The emergence of an innovative production technology is then potentially requested as VOD and AOD processes have emerged, which has saved substantial production cost. This paper describes a possibility of a future stainless steelmaking process, which uses the in-bath smelting reduction of chromium ore in BOF, and which would save production as well as energy cost."

Jan 1, 1988

By Peng Jianping, Feng Naixiang, Di Yuezhong, Wang Yaowu, Pan Xijuan

A vacuum silicon thermal reduction lithium process is developed in present work which used lithium hydroxide, alumina and calcium oxide as raw materials. The process contains two steps, which are that Li5AlO4 clinker is prepared in ambient environment, and that metal lithium is extracted from Li5AlO4 clinker with ferro-silicon alloy as reductant in vacuum. On the basis of thermodynamic analysis and investigative experiments, feasibility of this process is proved. The results show that Li5AlO4 can be generated by calcination lithium hydroxide and alumina, the burning loss is above 31% under the conditions of calicination temperature above 750℃ and time more than 90min. The main phases of calcination product are Li5AlO4 and CaO. When the calcination product is reduced by ferro-silicon alloy in vacuum, the lithium reduction ratio can be over 80% under the conditions of reduction temperature 1200℃ and reduction time 60min.

Jan 1, 2014