Search Documents

By G. White

Traditional atmospheres used for Aluminum annealing have been air, exothermic gas, and cryogenic purity Nitrogen. Air and exothermic gas have several problems associated with them such as surface discoloration, toxic emissions, and explosion hazards. High Oxygen levels can cause Magnesium streaking and oil staining, and therefore pure Nitrogen has been the atmosphere of choice for high quality Aluminum coils. A comparative study was made on key Aluminum alloys annealed in Nitrogen with different Oxygen concentrations to determine the effect on surface quality. The atmosphere composition inside the furnace was analyzed during the purge and heat cycle to determine its effects on purge times and exhaust emissions. The Aluminum coils after annealing were visually inspected for surface staining before and after rolling. The lab study revealed that Nitrogen with up to 1.0% Oxygen is acceptable, and did not adversely effects the surface quality or any of the other processing variables. However it isbelieved that higher Oxygen concentrations are acceptable depending on the rolling oils and alloy systems.

Jan 1, 1996

By Elli Miettinen, Markku Lahtinen, Ilkka Kojo

"The recent trends of decreasing energy consumption and environmental emissions and utilization of economies of scale are strong drivers favoring continuous copper converting processes. Flash Converting benefits from low off-gas volumes and low investment and operational costs for off-gas treatment. Separate matte and blister furnaces allow the adaptation to concentrate quality changes and flexibility in layout and maintenance.The stationary blister copper bath in Flash Converting furnace is less aggressive to the furnace linings than agitated processes, resulting in low refractory consumption, long campaign life and high on-line availability.Copper Flash Converting has been successfully applied in Kennecott with a campaign life now exceeding five years. A second FCF was started at Xiangguang Copper in China in 2007. The process itself is proven, as its features are similar to those in FSF, Direct-to-Blister and Direct Outotec Nickel Flash Smelting (DON), with one significant difference: it is the easiest of all to operate.The paper presents differences between continuous Flash Converting and conventional converting based on recent experiences and studies."

Jan 1, 2009

By Kee Jeung Lee

In this study the characteristic factors and formation mechanisms for the hydrothermal preparation of a -quartz crystal powders were investigated to find the optimum synthetic conditions. The degree of Q -quartz crystal face development depended on the relative growth rate of a particular form that varies considerably with the degree of supersaturation, the reaction temperature, the concentration of mineralizers, and the presence of seed crystals in the feedstock. Alkali hydroxides and alkali halides were found to be effective in the reactions as mineralizers, which added in order to increase the solubility of the feedstock. The fine Q -quartz crystal powders were obtained in the temperature range of 250-450% and pressure range of 100-300atm. As the concentration of mineralizers increased, the particle size of crystalline powders became smaller at lower reaction temperatures. The fractional size distribution of synthetic crystal powders was depended on the hydrothermal conditions. As the reaction time and the amount of seed crystals increased, the width of particle size distribution became narrower. The weight mean particle size was in the range of 1 to 10m. The characterization of the products were carried out using XRD. SEM. PSA, FT-IR, Raman spectrometer.

Jan 1, 1997

By María Cristina Ruiz

Hematite precipitation is a convenient alternative for the removal of iron from leaching circuits because of its chemical stability, high density and high iron content. The precipitation of hematite from ferrous sulfate solutions was studied in a batch reactor. The precipitation occurs by two sequential steps: oxidation of the ferrous to ferric ions followed by hydrolysis of the ferric to hematite. The main objective of this study was to determine the effect of the main operating variables on the rate of two steps of hematite precipitation. The variables studied included: stirring speed (100 to 600 rpm), temperature (160 to 200 ºC), concentration of sulfuric acid (1 to 10 g/L), initial iron concentration (1 to 15 g/L), and partial pressure of oxygen (1 to 6 atm). The sulfur content and the particle size of the solids that precipitated under various conditions were also determined. The results showed that at low temperature and high acid concentration the rate of Fe3+ hydrolysis is the step that controls the overall process. The variable that affects most the rate of Fe2+ to Fe3+ oxidation and the rate of hematite precipitation is the temperature.

Jan 1, 2008

By Ronald H. Church

Dewatering of mine waste slurries has been successfully accomplished by the proper use of polymers in flocculating the fine particulate matter suspended in the slurry streams. Conventional treatment of fine waste slurries usually involves some form of impoundment treatment or storage. These impoundments present unique environmental problems. When filled to capacity, the impoundments are usually unloaded with a dragline and transported to a separate disposal area. The U.S. Bureau of Mines has conducted dewatering studies utilizing polymer technology in combination with a mobile field test unit designed by the Bureau. The purpose of these studies was to determine if the fine waste slurry from the mining operation could be successfully dewatered. Results of the investigation have shown that the slurry can be dewatered successfully. The dewatered products obtained from the tests ranged from 45 to 50pct solids. This material continued to dewater, approaching 70 pct solids within 24 h, and could be easily handled using conventional transportation equipment including conveyor belts.

Jan 1, 1994

By R. E. Fanning

"IntroductionThe Aluminum industry is one of many materials industries which strive to make their material the preferred choice for large volume products. In some applications one material has a natural advantage over others, but more frequently several materials compete with one another, each providing one or more advantages and some trade-offs. Customers may design their product with several objectives such as minimum system cost, maximum customer appeal or maximum manufacturing flexibility, choosing materials which best combine cost and performance. In such markets it may become necessary for a material supplier to enhance the attractive features of the particular material to outweigh its disadvantages.It is difficult, if not impossible, to predict how various materials will evolve. Technological breakthrough, government regulations, material availability or sociological issues may redefine the balance between competing materials. In spite of some uncertainty regarding the competitive position of competing materials, there is little doubt that unrelenting pursuit of product quality improvement and cost reduction are essential to future viability of the aluminum industry. It is the intent of this paper to identify some areas where technological improvement would be beneficial. Thus this paper is a collection of briefly described problems that will hopefully stimulate the thoughts and research required for knowledge based solutions. Rolling ProcessA particular example is the beverage can industry where aluminum, steel, glass and plastics vie for a share of the m.arket. The high cost of aluminum relative to steel or glass requires minimizing the amount of metal per can. The high intrinsic value of aluminum has led to extensive recycling of cans although net metal cost is still higher than that of the competing materials. Intensive engineering of the beverage can led to improved design and better understanding of material requirements. These improvements permitted substantial reduction in sheet thickness over the past decade. The downward trend in metal thickness for beverage can sheet is shown in Figure 1."

Jan 1, 1988

By A. V. Tarasov, V. M. Paretsky

"The design is based on the thermal processing of the wastes in· the intensively bubbled melt in the Vanyukov furnace at the relatively high temperatures (1350- 1450 °C), In this case: -the secondary wastes are not formed; - the especially toxic substances at the outlet from the furnace are absent. The technology was tested on a large scale (on semicommersial bases). Technical and economical basis show profitability of recovery complex for processing of hard garbage waste (HGW) using this technology: the period of capital, investments refunding for the, recovery, complex construction with process annual capacity of 240 thousands tons of wastes is 1,5-2,5 years,"

Jan 1, 2000

By Chuang Y-Y

A summary is made on the thermodynamic analysis for two of the four ternary systems of the quaternary Cu-Fe-Ni-S. The analysis is being extended to ternary Cu-Fe-S and then to the quaternary. An analysis is already made for the metal ternary but is not reported here. Experiment is being carried out to measure the liquidus surface. of Fe-Ni-S equilbrium with the fcc solid solutions of (Fe, Ni). The presentation at the Symposium will include all the results obtained at the time of presentation.

Jan 1, 1983

By Marco Pasetto

The possibility to re-use marginal materials (by-products) deriving from industrial activities in the construction of road infrastructures, as total or partial substitution of natural aggregates, successfully combines demands for economy and environmental sustainability. The paper presents the results of a laboratory study, conducted at the Experimental Road Laboratory of the University of Padova, to verify the suitability of a particular type of electric arc furnace slag to be recycled in the lithic skeleton of high-performance asphalt mixes (porous asphalt, high modulus mixes, stone mastic asphalt, nonskid surfacings) for road and airport flexible pavements. the process of transformation of iron and steel slag into a product that can be used in road building is described, along with the characterisation of the mixtures, plus an analysis of the results of a wide battery of mechanical-performance tests. This study forms part of wider theoretical ? experimental research being done at the University of Padova in order to improve knowledge of the characteristics of succedaneum materials and check their possible applications in road and airport construction.

Jan 1, 2006

By Hector M. Henao

In order to provide the thermochemical data regarding the slag system, which are of importance for sulfide smelting and metallurgical processes but still lacking, an experimental study was carried out on the phase relations and activity of iron oxide in the FeOX-CaO-SiO2 system at temperatures between 1300 and 1400 °C and partial pressures of oxygen between 10-9 and 10-4atm. First, the solubility of CaO and SiO2 in the solid FeO were obtained and the tie lines connecting between the solid wustite (FeO) or magnetite (Fe3O4) phase and the liquid phase were determined. Secondly, iso-activity lines for FeO in the homogeneous liquid region were determined, based on the activity of iron in the Pt-crucible used in the equilibrium experiments. The activity coefficient of FeO in this region was also derived from the composition of FeO and FeO1.5 in the liquid region. Finally, the effect of (CaO/SiO2) ratio in the system and partial pressure of oxygen on these thermochemical quantities is discussed.

Jan 1, 2006

By Guangchun Yao, Chuan Li, Hongjie Luo, Zhuokun Cao

"The expansion rate and collapse time of liquid aluminum foams are essential for the determination of operating time and quality of the resulting foam. In the present paper, liquid aluminum foams was fabricated by adding in TiH2 as blowing agent, and the variation of expansion rate with foaming time was non-contact detected by a laser distance measurer. The influence of different stabilizing agent and alloying elements was studied. The results show the fact that the fraction of stabilizing agent only perform little effects on the maximum expansion rate of liquid aluminum foams, while the influence of alloy elements are remarkable. The maximum expansion rate would increase much when Mg is added, and the liquid foam also collapse at a shorter time. Comparison was made between experimental results and mathematic calculations, which reveal the fact that it is the change of TiH2 decomposition responsible for the change.IntroductionMetal foams, combining light weight with other unique mechanical and physical properties, have gained wide interest and been developing fast during past few decades. However, manufacture of this new material is quite challenging since it involves simultaneous occurrence of gas, liquid and solid phase at high temperature [1-2].Quite some manufacture routes have been developed for manufacturing metal foams, and the structure and quality of resulting foam are remarkably improved during the last decades. However, most of the past works seems to be experiential, and because the lack of basic knowledge of foaming process, the start material is limited and the production technologies are far from reliable and reproducible.[3-4]In direct foaming process, decomposition of blowing agents, TiH2 for example, is the main force for foam expansion. The density and foam structure changes with time during the foaming process, so it is expected that foams of certain structure can be obtained by solidification of the liquid foam at a certain time [5-6]. However, the foaming process is weak in reproducibility and the influence of stabilization additives and alloying elements is unclear."

Jan 1, 2011

By Dean G. Heitt

"The Rain and SMZ mines from 1987 to 1994 produced a total of22.0 t of gold from a pre-mine reserve of 14.24 Mt of ore grading 2.13 g/t Au.Gold at Rain is hosted within the basal portion of the Mississippian Webb Formation. ·Mineralization is closely tied to the Rain Fault which is interpreted to be the main feeder for the deposit. Multiple collapse and hydrothermal breccia events provided permeability for the mineralizing fluids in the otherwise unreactive siltstones. Major alteration events include: decalcification and dolomitization of the Devils Gate Limestone; and silicification, baritization, argillization and oxidation of the Webb Fm. Six ore types based on XRD and visual rock chip Jogging have been identified: siliceous ore containing >40% quartz and <30% barite; siliceous-baritic ore containing mostly silica but >30% barite; baritic ore containing >40% barite; argillaceous ore containing >40% total clays (including alunite); calcareous ore containing mostly calcite and dolomite; and carbonaceous ore which has significant pyrite and organic carbon. Metallurgical testing of the oxide leach grade ores found that recoveries, on -1.3 cm crushed material, were greater than 70%. Results also found that Rain ore has strong grind dependency due to silica encapsulation.The Rain leach pad was commissioned in 1988, and to date 9.3·Mt at an average grade of0.65 g/t Au have been placed. Life to date recovery, through December 1995, is approximately 51 %, for a total of3.87 t of gold produced. Two major factors have contributed to the low leach recoveries at Rain when compared with the metallurgical testing: 1) More argillaceous ore than expected was placed on the pad especially late in the mine life and 2) approximately 50% of the tons placed were run-of-mine with no agglomeration."

Jan 1, 1997

By Bart Blanpain, Tom Peter Jones, Muxing Guo, Liugang Chen, Huayue Shi

Fayalite based slag is formed during the smelting process of secondary copper resources. It was found that with the presence of high ZnO, the slag became viscous, causing a slag tapping problem. In the present paper, the phase relations of the slag system ZnO-“FeO”-SiO2-Al2O3- CaO (ZnO = 0-12 wt%, Al2O3% = 0-15 wt%, CaO = 0-1.5 wt%, with iron saturation) at 1150 °C is studied by using quenching technique followed by phase identification and compositional analysis of equilibrated samples. The dependence of FeO and Al2O3 solubility in the liquid slag on the chemical composition of slag is characterized. Based on the experimental data, the solid fraction of the slag, which may considerably, influences the slag viscosity, at the tapping temperature can be reasonably estimated and, therefore an appropriate modification of the slag composition can be made.

Jan 1, 2016

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By Francis Vanbellen

In Union Minière&apos;s Hoboken smelter and refinery for complex non-ferrous materials, the treatment of recycling products, containing precious metals, occupies a dominant place. For all feed materials, the first step, prior to their treatment, is to classify them in order toselect an accurate and economical procedure for sampling as well as to dispatch them to the optimal process scheme. More than 150 different procedures for sampling are commonly used. The most important ones are briefly discussed in the paper. Precious metals bearing recycling materials vary widely with respect to their physical aspect, their chemical composition and the value of their precious metal content. All these parameters are taken into consideration to select the most appropriate process among the multiple possibilities of Union Minière&apos;s flexible integrated flow-sheet. Different stages of the operations as well as the main flow-sheets are described.

Jan 1, 1995

By Suguru Kohno, Yoshihiro Momose, Masakazu Honma, Tokirou Kamosawa

Copper metal surfaces have been examined by an extremely sensitive surface analysis technique called temperature programmed photoelectron emission (TPPE). The surfaces were ultrasonically cleaned and subsequently abraded by a screw in organic solvents and water. The TPPE apparatus is composed of a Geiger counter with Q gas (He+ iso-C4H10). The curve of photoelectron emission (PE) intensity vs. wavelength from 300 to 170 nm, termed PE spectrum, was repeatedly measured at different temperatures in the temperature- increase process from 25 to 350°C. The number of emitted electrons in a PE spectrum (PE total count) increased, reached a maximum at-250°C, and decreased with increasing temperature. With the surfaces cleaned alone in the liquids the maximum PE total count decreased in the order C3H70H > (CH3) 2CHOH > C2HpH > CHPH > H2O. With the mechanically abraded surfaces in the liquids the maximum PE total count changed as a function of the abrasion period and the maximum tended to appear at higher temperature with increasing abrasion period; the maximum value at 10-min abrasion decreased in the order H2O > CHpH > C2HPH > (CH3) 2CHOH > n-C3HpH. It was suggested that the TPPE behavior can be related to the acid-base interaction between the alcohols and the abraded metal surfaces and the presence of a contaminant over layer on the surface. From the XPS analysis of the 01 s spectra it was suggested that the chemical change of the adsorbed oxygen to oxide oxygen with temperature plays a substantial role in the appearance of the maximum PE total count.

Jan 1, 2000

By A. Siegmund, Gerhard Martin

The recycling of metal containing scrap is a common practice in the industry and has a long tradition. . In rec~nt years, this philosophy has been transferred to organic materials, in particular to thermoplastic polymers. BSB . Recycling GmbH, a company with a long experience in the treatment and recovery of lead from battery scrap,· had recognized this exploitation at an early stage and challenged it by a consequent continuation of the idea to recycle materials other than metals without degradation and maintaining the quality. These efforts resulted in an economic and environmentally acceptable solution producing high quality polypropylene compounds at BSB beside lead and lead alloys from battery scrap. The raw material fair the production of polypropylene compounds is shredded plastics from the separated casings of spent lead-acid batteries. The production of polypropylene with specific physical and mechanical properties is carried out by the accurate dosing of organic as well as inorganic additives. The result of the procedure is a novel product group "Seculene PP", a registered trademark of BSB Recycling GrnbH.

Jan 1, 2000

By Fan Xiao-Hui, Jiang Li-Juan, Chen Xu-Ling

"In order to solve air leakage of sintering testing cumbersome, inaccurate results, and other issues, the sinter machine air leakage characteristics were studied, and combining the mathematical modeling and the field detection. The temperature before air leakage was calculated by mathematical model, energy balance equation was established according to sintering process, using Adams prediction correction method which has stronge stability and high precision, to solve hyperbolic partial differential equation with astringency problem. The temperature after air leakage is detected by instruments, according to energy conservation calculation the sintering air leakage rate. According to the sintering continuity and periodicity, sintering air leakage location diagnosis expert system was established to judge specific air leakage locations.IntroductionStrengthening of modern blast furnace production depends on the quality of the raw material preparation to a large extent [1]. Technical and economic index of modern blast furnace production is advanced; the most important reason is the use of concentrated feed. Sintering plant is the ""kitchen"" of blast furnace’s concentrate. As we all know, sintering plant is major energy consumption of steel plant, in sinter process energy consumption, the solid fuel consumption of total energy consumption is 75%~80%, power is 13%~20%, ignition and combustion is 5%~10%. To reduce the air leakage of sintering plant is an effective measurement to save energy consumption. At present, our air leakage of sintering compared to the other developed countries is still a long way to go. Japan’s air leakage rate is about 30%, and 35%~60% air leakage of sintering machine at home, a big gap exists between the plants. At present the determination of air leakage is all for manual operation, long measuring period, considerable manpower and resources, and the results are significantly affected by operation. For air leakage of sintering control lag issues, research and development of diagnosis expert system for on-line monitoring model for air leakage and, through this research can reduce the use of detection equipment, detect sintering air leakage, improve the yield and quality of sintering production, reduce energy consumption, and extend equipment life span."

Jan 1, 2012

By Evgueni Jak

Recent advances in analytical, experimental techniques, and computer-based theoretical modelling of fundamental properties and elemental processes, provide new opportunities to develop the next level of whole-of-reactor pyrometallurgical furnace models. These models have the potential to significantly improve the prediction of, and adding value to, industrial operations. In non-ferrous smelting, the starting point of these models is the development of multicomponent thermodynamic databases for gas-slag-matte-speiss-metal-solids phases supported by systematic experimental research. The whole-of-reactor-models additionally should take into account kinetic processes taking place at micro- and macro- scales, and other key factors. Examples of applications of the latest research tools and modelling approaches to analysis of industrial flash and top submerged lance (TSL) sulphide smelting processes are presented. Different levels of industrial modelling are discussed from elemental local reactions, through general and more detailed whole-of-reactor-models, to plant sections and further to whole plant operation models. Some principles for development of pyrometallurgical reactor models are discussed.

By A. A. Hejja

"Liquidus temperature and electrical conductivity data measured on synthetic slags were modelled by the use of neural nets (NN). In this work the applied multilayer feedforward NNs were trained by a conjugate-gradient optimisation for which a three layer formulation was used. Very good fits were obtained for both the liquidus temperature and the conductivity data. The synthetic slags were prepared from pure oxides to represent a wide range of compositions likely to be encountered in ferromanganese and silicomanganese smelting. The slag constituents were in the following range: Mn0;5-30%, Ca0;20-35%, Mg0;5-15%, Si02;27-58%, Al20 3;5%. Liquidus temperatures varied from 1300° to 1380° and increased with increasing basicity ratio. The electrical resistivity of slags decreased with the increase of basicity ratio from 0.55 to 1.1 but above 1.1 basicity ratio the resistivity tended to increase depending upon the MnO content.Neural NetsVarious neural net (NN) topologies such as Hopfied nets, Hamming nets, Carpenter/Grossberg classifiers have been discussed in some detail by Lipmann (1). In this work, the applied multilayer feedforward NNs are not trained by backpropagation (BP) using the generalized delta rule (2) (GDR), but by a conjugate-gradient optimisation [3,4] - a procedure similar to that proposed by Barnard and Cole [5]. A neural net is capable ·of learning the non-linear functional relationship existing between a set of inputs and outputs [ 6]. In this capacity a neural net is used to determine the functional relationship that exists . between N dependent and independent variables, which characterize the system under consideration For a three layer neural net [1] the following function may be formulated, which relates X; inputs to the output Y 0 from node o:"

Jan 1, 1997