Search Documents

By Ruixiang Wang, Jinhui Li, Youjun Xiao, Daoling Xiong, Hao Chen

"Leaching solution prepared from spent battery materials contains large quantities of valuable metals, such as Cu, Ni, Co, Mn and Fe. Therefore, recovery of valuable metals from acidic polymetallic aqueous solutions is of great importance for every plant. In this work, a method is introduced of recovery of Ni, Co and Mn from polymetallic solution prepared by leaching spent battery material. The basic concept includes copper was removed through replacement by iron powder followed by iron precipitation in goethite method. The experimental results show that Cu can be removed 99% at least through replacement by Fe powder, and the removal of Fe can achieve 99% by goethite method. At the same time, the loss of Ni, Co and Mn are about 2%, 3 % and 2%, respectively. The process of differential removal of metals can be selected as the treatment alternative that combines simplicity, efficiency and reliability with low capital and maintenance costs. The purified solution which only contains Ni, Co and Mn can be used to prepare NixCoyMnz ternary system precursor.1 IntroductionNickel and Cobalt are very important metals which are applied in many fields, such as energy material and support material for some new material field. The world demands for such metals is progressively increasing, while raw resources are being depleted and with the constraints raised by the Law and related legislation assigned to protect the environment from hazardous wastes in the world. Nowadays study on reutilization of waste materials has great significance for achieving secondary resources recycling and preventing environmental pollution. There are many hydrometallurgy methods applied for dealing with these wastes, while they usually contain large quantities of valuable metals, such as Cu, Co, Mn and Ni, as well as impurities, such as Fe, Zn, and etc. Therefore, proper treatment of these leaching solutions prior to their discharge is of great importance, so that the contained valuable metals can be recovered.Separation and extraction of metals from leaching solution can use some methods through solvent extraction[l,2], ion exchange[3,4], precipitation with sulfide[ 5] or alkali[ 6] and electrolytic recovery[?]. Among the appropriate treatment alternatives, replacement and differential precipitation is the most attractive treatment that combines simplicity, efficiency and reliability with low capital and maintenance costs."

Jan 1, 2011

By Kazuyuki Kakegawa

"Sintered body of lead zirconate titanate (PZT) was prepared through the spark plasma sintering (SPS) technique. When the mixture of raw materials was calcined at 800°C and sintered at 900°C for 10 min. with SPS technique, the sintered body had almost theoretical density but was a mixture of lead titanate (PT) and PZT. When a calcining temperature of 1100°C was employed, sintered body had a single PZT phase but a lower density. High dielectric constant was obtained for a sample calcined at 800°C, sintered with SPS tecbriique and fired again in the air at 1100°C.IntroductionSpark plasma sintering (SPS) is a recently developed technique for sintering metals and ceramics1. The scheme of SPS is shown in Fig. 1. Sample is put in a graphite die in a vacuum chamber. It is pressed and pulse voltage is applied. The electric current heats the die. It is said that the pulse causes a spark-plasma between particles in the sample. Because of the spark- plasma, sample can be sintered at temperatures lower than that in the ordinary sintering by several hundred degrees of Celsius. The sintering period is also very short2Low sintering temperature and short sintering period in SPS technique cause low reaction rate. It is both disadvantage and advantage. In some cases, the reaction cannot be completed under the SPS conditions. If a mixture of several compositions having different properties can be sintered without a compositional change by the diffusion during the sintering, combination of properties, and therefore a design of property will be possible3. The low reaction rate of SPS may enable such combination."

Jan 1, 2000

By Jiann-Yang Hwang

The economic growth in new developing countries such as China and India has stimulated strong demands in basic materials such as steel. World steel production has exceeded the milestone of a billion tons a year recently. However, the blast furnace technology, which was invented in 1340 A.D., is still the fundamental route for today?s steel production. It is important to develop a new generation of steelmaking technology that can meet the society?s needs from the energy, environmental and economic standpoints in the 21st century. The new microwave and electric arc heating technology discussed in this paper provides a totally different mass and heat transfer mechanism from the conventional blast furnace technology and offers a great potential to meet our society?s needs.

Jan 1, 2006

By Moto Goto

PT Smelting, located in Gresik, East Java, is the first copper smelter and refinery in Indonesia. Since the first charging concentrate in December 1998, many equipment troubles have been systematically eliminated, and the present operation is smooth and has accomplished the design capacity of 200,000 tonnes per year of LME, grade-A copper cathode. This paper describes troubles and countermeasures, which were experienced until now.

Jan 1, 2002

By Baoxiang Zhang, Jing Zhang

"As extruded Mg-9Zn-0.6Zr-2Er magnesium alloys were hot-rolled at 400°C, followed by solution treatment at 400 °c for 1. 5h and artificial aging at 200°C for 10h. Microstructures and tensile mechanical properties of the alloys after hot rolling, solution and aging treatment were examined respectively. Optical micrographs of the as-rolled and as-solution alloys showed fine grain structures, due to the formation of Er-and Zn-bearing compounds at grain boundaries which obviously improved the thermal stability of the alloy. Yield strength as high as about 335 MPa was obtained for the as-rolled alloy, showing that the mechanical properties of the alloy was greatly benefit from the grain refinement and dynamic precipitation of fine MgZn2 during hot rolling. Due to solution heat treatment, vast majority of the Mg-Zn phases dissolved into the matrix, and precipitated out again as fine dispersoid during the subsequent aging, resulting in an enhanced aging-hardening effect.IntroductionWith high specific strength and low density, magnesium alloy has stimulated significant interest for the applications in microelectronics, aerospace and automobile industries. Due to its HCP structure, magnesium alloys exhibit relatively poor strength and ductility. Great efforts have been made to improve the properties of magnesium alloys.Thermo-mechanical processing which combined with subsequent heat treatment can strengthen magnesium alloys due to the strain-hardening mechanism, homogeneous distribution of second particles and grain refinement [1, 2]. However, commercial wrought magnesium alloys have high tendency of grain growth at high temperature due to lack of effective solutions to stabilize the microstructure [3, 4, and 6]. But Magnesium-RE alloys containing high rare earth were reported to have remarkable thermal-stability, Rare earth (RE), such as Y, Nd, Yb, Gd, Ce, were known to form second-phase particles that have higher thermal stability combining with Zn and matrix in Mg[12-17]."

Jan 1, 2012

By G. Ramadorai

"This paper addresses processing options for recovering gold from carbonaceous sulfidic gold ores. These include, but not limited, to the following methods: (1) Hypochlorite pretreatment followed by cyanidization; (2) Chemical blanking agents pre-treatment followed by cyanidization; (3) Non-cyanide heap leaching techniques; (4) biological pre-treatment followed by cyanidization; (5) biological pre-treatment followed by non cyanide heap leaching. Issues of costs, economics, recoveries, testing methods, state of advancement etc., will be discussed in the paper.ABSTRACT ONLY"

Jan 1, 1997

By Artur Camposo, Rômulo. L. Loiola, Frederico M. Margem

"The growing interest for natural materials as an environmentally friendly alternative for the substitution of energy intensive and non-sustainable synthetic materials, has motivated the use of lignocellulosic fibers as reinforcement of biocomposites. The sisal fiber, a relatively unknown lignocellulosic fiber with potential for composite reinforcement, still needs to characterize for possible engineer applications. Therefore, the present work analyzed the sisal fiber by means of Fourier Transform Infra-red (FTIR) spectroscopy. The sisal fiber FTIR spectrum revealed main absorption bands typical of any lignocellulosic fiber. However, some specific bands as well as bands broadening and intensity suggested particular activities for functional molecular groups in the sisal fiber.IntroductionIn recent decades, environmental issues related to worldwide pollution and climate changes, mainly the global warming, are motivating new paradigms for the development of our society. Among these, the use of natural materials in substitution for non-sustainable synthetic materials, obtained from non-renewable ores and petroleum, is increasingly being considered. In particular, natural fibers extracted from plants are, in this 21st century, experiencing a surge as composite reinforcement [1-11 ], following their replacement by synthetic fibers, specially the glass fiber, during the second half of the 20th century [1-2-8].In addition to environmental benefits [12-13] the lignocellulosic fibers present economical advantages, such as worldwide abundance and comparatively low costs as well as some technical properties associated with flexibility and toughness[ll], which contribute to the performance of automobile components fabricated with natural fibers composites[14-16].Among the less common lignocellulosic fibers that only recently have been investigated[l 7], the fibers extracted from the stem of the sisal plant, shows in Fig 1, reveals a potential for polymer composite reinforcement."

Jan 1, 2013

By Zbigniew Smieszek, Ryszard Chamer, Ryszard Prajsnar, Zygmunt Kurek

"Lead-containing wastes processed at the IMN’s Division in Legnica originate mainly from dry and wet dedusting installations of the technological lines for copper production. These are lead dusts and lead-zinc dusts characterised by the specific properties resulting from the chemical composition of the Polish copper concentrates. Besides lead, they contain many accompanying metals and impurities such as zinc, copper, sulfur, chlorine, potassium, sodium, and also bituminous substances. Processing of lead-containing dusts is conducted in the installations of rotary-rocking furnaces heated with gas-oxygen burners fitted with auxiliary systems for cleaning process gases and refining re-circulating dusts. The processing technology utilizes innovative process and technical solutions enabling disposal of lead-containing wastes from copper metallurgy and from non-ferrous metals industry according to the BAT recommendations and to the guidelines specified in integrated permission. In this paper, the main technological aspects of processing lead-containing dusts at the IMN’s Division in Legnica have been presented.IntroductionCrude lead is obtained in Polish lead metallurgy from various primary and secondary materials, such as Zn-Pb concentrates, lead-bearing dusts of copper metallurgy and battery scrap. In zinc smelter Miasteczko Slaskie S.A. crude lead is produced from sulfide and oxide Pb-Zn concentrates in ISP process. Orzel Bialy S.A. and Baterpol Ltd. produce crude lead in short rotary furnaces in the process of smelting products of mechanical battery scrap separation– desulfurised or not desulfurised paste and metallic fraction. KGHM Polska Miedz S.A. and IMN Divison in Legnica produce crude lead in rotary furnaces in the process of smelting of polymetallic dusts and slimes from copper production processes."

Jan 1, 2008

By W. G. Davenport

Chapters 19 and 20 examine direcHo-copper flash smelting and flash converting. This chapter compares the two processes and suggests which is likely to be 'the more economic for a given concentrate. It: (a) uses Chapter 19's direct-to-copper industrial oxygen and oil requirements (b) adds the energy required for electric furnace recovery of Cu from direct-to-copper slag (Czemecki et al 1999) (c) combines Chapter 20's, flash converting calculations with Chapter 18's flash smelting calculations to determine their combined industrial oxygen and hydrocarbon fuel requirements (d) adds the energy required to granulate, crush and dry flash smelting matte for the flash converter (e) adds the energy required to granulate and dry flash converter slag for recycle to flash smelting (f) compares direct-to-copper and flash smelting/flash converting in terms of their total equivalent hydrocarbon ener.gy requirements.

Jan 1, 2001

By D. A. Milligan

Ammonia leaching of copper sulfide concentrates, matte, scrap or other sources of copper yields copper amnine sulfate solutions which are converted to metal in a two-stage process involving precipitation of inter- mediate sulfites and their thermal decomposition to copper powder of high purity. Processing details and results are given. Considerable simplification in circuitry and cost savings are indicated. Energy requirements are reduced by substitution of copper powder precipitation and ammonium sulfate crystallization for solvent extraction, electrowinning and lime boil.

Jan 1, 1976

By Tangstadm Merete, Eli Ringdalen

"This paper presents an overview of results from The Norwegian Research Institution SINTEF and the Norwegian University of Science and Technology, NTNU regarding new and ongoing research in silicon production. The main studies are related to condensation of SiO gas and cavity formation. If SiO gas condensation is increased at the top of the furnace resulting in SiO content in the off-gas closer to equilibrium, the Si yield will be increased significantly. Experimental work, simulating a cavity under industrial conditions, has shown that the cavity grows downwards from one layer. Physical appearance of zones in industrial furnaces, and selected reactions in these, are discussed based on results from excavation of industrial furnaces and results from laboratory experiments. Experimental studies of reaction rates for the formation of SiO are presented. Quartz properties are demonstrated to vary between differing quartz types and the effect of this is discussed.Introduction Both the theoretical and industrial issues associated with the production of silicon are described in detail in the textbook written by Schei et al [1]. This book covers the knowledge of silicon production process up to 1998. Together with the work by Myrhaug [1] and by Aasly[2], this is the main basis for this paper. Recent and ongoing research at SINTEF and NTNU focusing on production of Si and SiO in the high temperature zone, dissociation of SiO and condensate and cavity formation will be discussed."

Jan 1, 2012

By H. Tan

?Preg-robbing? is the active adsorption of gold from cyanide solution by the ore components. The role of carbonaceous coatings on chalcopyrite surfaces in the preg-robbing of chalcopyrite has been investigated by using pure chalcopyrite and a copper concentrate. Activated carbon and graphite were chosen as representative carbonaceous contaminants. It was found that the carbonaceous coatings enhanced the preg-robbing of chalcopyrite. Activated carbon coating increased gold adsorption onto chalcopyrite to a lager extent, in comparison with graphite coating. In the preg-robbing of the copper concentrate, gold adsorption was increased to larger extent at finer particle sizes and at higher contents of activated carbon or graphite. The preg-robbing of chalcopyrite was reduced or eliminated, depending on the concentrations of free cyanide. However, the gold adsorption on the carbon and graphite coated chalcopyrite could not be avoided even at higher cyanide concentrations, and this adsorption was solely attributed to the carbonaceous coatings. Zeta potential studies indicated that the carbonaceous coatings reduced the negativity of the chalcopyrite surface charge. As shown by SEM analysis, gold not only accumulated at the edges and defect sites, but was also spotted on the smooth surfaces of chalcopyrite with carbon or graphite present. XPS results revealed that gold was strongly reduced on chalcopyrite surfaces, with the sulfide ions of the chalcopyrite being oxidized to elemental sulfur. Diagnostic elution indicated three mechanisms contributing to gold take-up by chalcopyrite, i.e. gold reduction, physical adsorption and chemical adsorption.

Jan 1, 2003

By Jilai Xue, Jun Zhu, GermainKouma Ndong, Luxing Feng

High-temperature corrosion behaviors of Fe-Ni-Cr alloy as inert anodes for aluminum electrolysis have been studied. The effect of anodic overpotential on layer growth of anodic surface is specially considered. The corrosion layers on the anodes tested were analyzed using XRD and SEM-EDS to provide a fundamental understanding of the layers growth at metallic anode surface. The dissolution of the scale layers on the metal anode occurred with low overpotential, while AlxM3-xO4 spinel phase within the scale layers was found with an increased overpotential. A mixture of multiple MyO layers existed on the anode substrate. The results may be useful for understanding and controlling the corrosion behaviors of Fe-Ni-Cr anode for potential application in aluminum electrolysis.

Jan 1, 2015

By Jr. Santafé, Lucas L. da Costa, Felipe P. D. Lopes, Sergio N. Monteiro

"Residual vegetable fibers as leftovers from crops, industrial activities and consumable items are realistic options to be incorporated into low cost polymeric composites with the aim of replacing other commonly used materials. The present work assesses the technical properties of epoxy composites reinforced with residual fibers from the coconut fruit, also known as coir fibers. Based on these properties, an evaluation was carried out on these coir fiber/epoxy matrix composites to be used as building panels and furniture in comparison with conventional materials.IntroductionThe utilization of waste from industrial activities is presently recognized as important way in preventing environmental pollution as well as developing new products. This utilization would also generate employment and contribute to environmental improvement in global scale. Among such wastes, those from lignocellulosic materials represent a considerable potential for practical application. In fact, about 2.5 billion tons of these materials are currently available [1], and their fiber content is an important option for composites fabrication. Actually, lignocellulosic fibers are now replacing synthetic fibers as reinforcement in resin matrix composites owing to specific advantages such as low cost, biodegradability and renewable characteristics [2,3]. Moreover, as abundant waste, some of these lingocellulosic fibers could help reducing the use of traditional materials like wood and plastics in many industrials applications. This would prevent further stress on the environment caused by depletion of dwindling resources associated with forests and petroleum."

Jan 1, 2008

By Robert De Saro, Willis Bateman, Ramesh Jain

A Vertical Floatation Melter (VFM) has been developed (sponsored by DOE) which simultaneously decoats and melts organic laden scrap in a single unit. Scrap aluminum is fed into the top of the VFM where it falls through a cone. Hot gases flow upwards through the cone, imposing a variable drag force on the scrap. Equilibrium is reached in which the scrap weight equals the drag force and the scrap becomes suspended. The gases strip off and vaporize the organics. Next, the scrap reaches a liquid state, taking on a more aerodynamic teardrop shape, allowing it to fall into a holding furnace. Heat transfer coefficients are 10 times higher than that of a conventional furnace, allowing rapid melting at a low gas temperature. Typical energy use is well under 2,324 joules/g (1,000 Btu/lbm) with a metal yield from 92 to 98%. This paper reports on the operation and data of a 453 kg/hr (1,000 pph) pilot-scale VFM.

Jan 1, 2000

By Keizo Uematsu, Satoshi Tanaka, Zenji Kato, Nozomu Uchida

"A novel technique is developed and applied to evaluate the binder segregated at the· surface of granule. Compressive strength of each granule was measured directly with a micro-compressive instrument. The relation between compressive characteristics and the amount of binder was discussed quantitatively.IntroductionCharacterization of granules is essential in the production of ceramics, since they govern the structure of green compact and thus the structures and properties of ceramics. However, there is no research to clarify the relation between the strength of granules and structure of granules, especially of binder segregation at granule surface. We develop a novel technique to determine the binder concentration in the granules by the iodine method. In this study, we measure yield strength of granules directly and discuss the relevance between compressive characteristics and the concentration of binder.ExperimentalGranules were prepared by spray-drying of aqueous slurry of commercial alumina (AL160-SG1. Showa Denko, Tokyo, Japan) and PVA (PVA 105 Kurare, Japan). PVA. concentration in granules was 1.1, 1.5 and 2.3 wt%. The inlet and outer air temperatures were 200 and 95 °C , respectively. Iodine-potassium iodide solution was prepared by dissolving iodine (0.15mol) and potassium iodide (0.15mol) in diluted water (50ml). A saturated boric acid solution was prepared by mixing boric acid powder with a diluted water."

Jan 1, 2000

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By Mehdi Asgharifar, Rouzbeh Sarrafi, Radovan Kovacevic

"The surface treatment of aluminum alloys using atmospheric-pressure of low intensity DC plasma arc discharge is investigated in terms of surface properties. With respect to the conventional surface treatment processes for aluminum alloys mostly based on chemical etching or sand blasting, this process is very environmentally friendly and cost-effective. The effect of two processing parameters, the current and the plasma torch scanning speed, on the surface morphology is studied by using a scanning electron microscope. The effects of cathode spots within the tested range of process parameters are determined, and the limiting factors of the process (such as surface cracking) are discussed. The topographical studies of the treated surfaces have suggested potential enhancement of surface properties for different applications, such as preparing surface for painting and adhesive bonding.IntroductionIn the last decade the aluminum alloys are finding broad applications in automotive industry. In order to successfully execute the joining process of aluminum alloys such as arc welding, laser welding, and adhesive bonding, there is a need to remove oxides for welding and texture the surface for bonding along the join line. A number of surface treatment techniques such as chemical etching, sand blasting, and plasma treatment have been used by industry. It is shown [1] that plasma surface treatment is characterized as environmentally friendly, lower cost, and easier to control process. Bogaerts et al. [1] mention that when an adequately high potential difference is applied between cathode and anode, electrons are accelerated toward anode by an electric field coming in collision with gas atoms. The gas breaks down into positive ions and electrons, giving rise to gas discharge. The DC electrical discharges used in industrial plasma sources can be related to their location on the voltage-current curve as shown in Figure 1.It is generally believed that dark discharges other than coronas, and arc or torch plasmas are not very good candidates for surface treatment because oflow or high power density and active species flux. However, the glow discharge plasma is used for plasma surface treatment applications because of its proper power density and active-species flux [2]. Our objective is to investigate the feasibility of using low intensity DC plasma arc discharge as a surface treatment method without damaging the cathodic non-thermionic workpiece."

Jan 1, 2011

By P. A. Davidson, D. J. Short

"In this paper we describe a 'non-contact' electromagnetic nozzle suitable for sprayforming and gas atomization processes. In such processes there is a need to control the flow rate and diameter of the liquid metal jet whilst minimising contamination of the stream. This can be achieved using an electromagnetic valve, which partially levitates the jet in freespace, using a segmented cylinder surrounded by an induction coil. This valve will significantly enhance the quality of the titanium alloys and nickel-based superalloys used in sprayforming and gas atomization. This paper describes the design and test of a laboratory prototype valve based on experiments performed with liquid tin.1. Introduction In many industries there is an increasing need for clean, high quality metals and alloys based on titanium and nickel. Two important processes are: 1) Spray deposition which allows the liquid metal to be converted to a near-net shape, thus alleviating the need for subsequent forging and extensive machining and; 2) Powder production of titanium by gas atomisation.In centrifugal spray deposition of titanium (see figure 1) the metal is induction melted in a cold crucible. The crucible consists of a number of water-cooled segments, which allows the high frequency magnetic field of the coil to pass through the crucible, and into the melt. The charge is melted by the induced eddy currents. Locally at the crucible walls the liquid metal solidifies, and is contained within a. 'skull' of its own solid, thus reducing contamination from the crucible wall. Once melted the metal is poured through an electrically heated graphite nozzle and into the spray forming chamber. The principal limitation of the process to-date, however, is that it currently uses a graphite and /or ceramic nozzle to direct the flow of liquid metal to the atomizing disk and as such there is considerable risk of nozzle erosion with inevitable effects in terms of contamination of the melt stream and variability in flow conditions. In this research programme we develop a. non-contact electromagnetic nozzle, which will totally eliminate refractories and/or ceramic materials from the melting and casting process. This will greatly enhance the technological capabilities of sprayforming and gas atomization processes."

Jan 1, 1999

By Hongmin Zhu, Kai Huang, Shuqiang Jiao

"Garlic peel was used as the raw material to synthesize the biosorbent for the selective recovery of precious metals from the acid chloride solution. Garlic peel is rich in carboxyl-, amino- and thiol-groups, has the potential of exhibiting high affinity to Au(III) when appropriate chemical modification process was employed. Here in the present study, the biosorbent was prepared by cross-linking garlic peel particles with concentrated sulfuric acid. Adsorption tests for mixing different metal ions such as Au(III), Fe(III), Cu(II), Ni(II) and Zn(II) from various concentrations of hydrochloric acid media indicated that Au(III) was selectively adsorbed on the cross-linked garlic peel gel over the other coexisting base metal ions investigated. The crosslinking mechanism and selective adsorption of Au(III) were also investigated briefly.IntroductionPrecious metals are quite popularly applied in the modern industries such as jewelry, electronics and electrical devices, catalysts in chemical industry, etc. While their high values, limited deposit and quite large demand in industry makes its recovery from the industrial wastes, typically e-wastes, quite necessary. Actually, many techniques have been developed to recycle and recover the precious metals from various industrial wastes effectively in last decades, but the cleaning and ecofriendly processes are still seriously scarce [1]. Taking into account of the typical recovery processes using cyanide lixiviant in the alkaline media, or aqua regia, followed by the further recovery process using activated carbon adsorption or cementation with zinc, iron or aluminum plate or powder, though they both are quite effective recovery processes, if considering the special requirements on safety and ecofriendliness for the modern hydrometallurgical processes, various improved or novel extraction processes are greatly demanded [2]. Recently, the biosorption technology applied to the recover precious metals in the hydrometallurgical process has become a concern [3,4]. Inoue’s research group made great progress in the recovery of precious metals such as gold, palladium and platinum from the e-wastes such as spent mobile phone by using biosorption from the hydrochloric acid media [5,6]. This new hydrometallurgical process exhibits the prominent advantages of being cost-effective for its short process, easy operation and near-zero emission. In the above recycling process for e-wastes treatment, the preparation of biosorbents is the key and backbone of the whole recovery process. For this purpose, they developed a series of suitable sorbents for precious metals recovery by using the tanning-based or cellulose-based biomass such as persimmon peel, grape peel, orange juicing residue, waste cotton, waste paper through the crosslinking process with concentrated sulfuric acid and relative chemical modification processes [7-10]. In the present study, we also applied this technique to prepare the biosorbent of precious metal uptaking by using garlic peels as the raw materials, and investigated the adsorption properties of such-obtained gel in the hydrochloric acid media."

Jan 1, 2012