Search Documents

By Roberto Parra

The operational control in a Flash Smelting Furnace is based on the mass and energy balance of the chemical and mineralogical composition of the concentrates. It is well known that many troubles in the dust formation and slag quality occur without a clear correlation to a specific process parameter such as the matte grade or heat balance. This paper outlines two new considerations that could both help improve the entire quality of the process: blend characterization and versatile slag composition control. Related to the blend control, laboratory scale study has shown that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of2 or 3 types of concentrates can be identified. Related to the control of stag composition, the quantification of the slag liquidus temperatures and viscosity could be an effective operational tool for both for ferrite and fayalite slag that can also directly help deciding the blending parameters. From these viewpoints the benefits of the combination of these two approaches for high temperature operation is discussed. Keywords: Optimization, Copper concentrates, Flash combustion, Blends, Slag composition

Jan 1, 2003

By María Cristina Ruiz

In the processing of copper concentrates by the conventional smelting-converting technology, complying with the increasingly severity of environmental legislation in some countries has become difficult, mainly due to severe fugitive emissions of gases produced during the batch PS (Peirce-Smith) converting step. In this work, the results of an investigation on the pressure leaching with sulfuric acid and oxygen of white metal (produced in a Teniente Converter reactor) are discussed. The study was carried out at laboratory scale and the main variables studied were temperature, concentration of sulfuric acid and partial pressure of oxygen. The experimental results indicated that most of the sulfur in the white metal was oxidized to sulfate in the whole range of temperature studied (105ºC to 150 ºC). The concentration of sulfuric acid over 0.05 M, and oxygen partial pressure over 6 atm had little effect on the dissolution of copper from the white metal. On the other hand, temperature had the most significant effect on copper dissolution; below 130 ºC copper dissolution was incomplete after 5 hours of leaching while at 150 ºC the dissolution was complete in 90 minutes and 10 atm of partial pressure of oxygen

Jan 1, 2006

By Chen Dong, Yuanling Gao, Jilai Xue, Jun Zhu, Luxing Feng

"Porous Ni-Ti alloy has many applications in a wide range of engineering areas. The porous NiTi alloys were prepared from Ti and Ni powders in sintering process under argon atmosphere. The major chemical compositions of the sintered Ni-Ti body were Ni Ti, Nh Ti4O and Nh Ti, respectively, the internal pore structures were characterized by image analysis technique, which were dependent on various processing parameters such as sintering temperature, amount of poreforming agent, forming pressure, etc. The results show that the porous alloy samples had the characteristics of uniform pore and high open porosity; pore-forming agent and sintering temperature are important factors in porous; pressure affected the sintered products' pore, by affecting the combination of alloy powder with pore-forming agent.IntroductionPorous Ni-Ti alloy materials exhibit not only excellent shape-memory and superelasticity, high yield strength and ductility, good corrosion resistance and biocompatibility, but also have low density, low stiffness, and high energy absorption rate due to their porous structures [1]. In recent years, these porous Ni-Ti alloys have found applications in a wide range of engineering areas, such as bone implants [2-4], impedance-matching connectors [5], energy-absorbing structures [6,7], separators [8] and actuators [9], etc.Pore characteristics can play very important role in determining of the performance of porous NiTi alloys. For example, when the alloys are used to repair or replace hard tissue implant material, the pore shape and size not only determine their mechanical properties, but also have great effect on the fluid transmission of human body. The pore characteristics can also influence the stressstrain behavior of the porous Ni-Ti alloy and, thus, strongly affect their mechanical properties, superelasticity, and fracture mechanisms [10].In this study, the Ni-Ti alloys with high porosity were prepared in a powder sintering process under argon gas. The pore characteristics were investigated using SEM, XRD and image analysis techniques, especially in association with the content of pore-forming agent, sintering temperature and compacting pressure."

Jan 1, 2011

By R. A. Sharma

Neodymium metal was successfully produced by the reduction of Nd203 with Na in the presence of CaC12-NaCl melts by the overall reduction reaction Nd203 + 3 CaC12 + 6 Na ? 2 Nd + 3 CaO + 6 NaCl at -750°C. The metal produced was extracted from the salt media by dissolving it in a Nd-Fe alloy pool. The yield (percentage of theoretical neodymium produced) was found to depend on the salt composition and the mass ratio of salt to neodymium in the reactor. A yield of 95% was obtained with salt ratios as low as 3.5. Further decrease in the salt ratio below 3.25 decreased the yield. Stirrer position had little effect on yield; while increasing the temperature and placing fins in the reactor increased the yield. The Nd-Fe alloy produced was of as good quality as that produced using Ca reductant, and was suitable for direct use in producing General Motors MAGNEQUENCH? alloy for permanent magnets.

Jan 1, 1989

By Wang Haibei

China is the important country in terms of Ga, Ge reserves and products. These elements usually associate with lead and zinc ores such as in Fankou, Dachang and Lanping mines. Until now these metals could not be extracted from zinc residues effectively. The main reason is that it is difficult to separate zinc and iron. BGRIMM has carried out considerable research on this subject and some hydrometallurgical processes were developed. Zinc residues were pressure leached with a reducing agent such as zinc concentrates or SO2 at 110~130C. The final concentrate of H2SO4 was 30~50g/L. The metals such as Zn, Fe, Ga and Ge were dissolved into solution. In the leaching residue Pb and Ag could reach 20% and 2000g/t. The feed of solvent extraction was prepared from the leaching solution by pre-neutralization ? precipitation of Ga, Ge and acid dissolving. Then Ga and Ge were extracted by solvent extraction through P204 and G315 produced by BGRIMM. After stripping, metallic Ga was produced by electrowinning. GeO2 was produced by precipitation. The iron in raffinate was removed by the hematite process. The solution after removal of iron came back at the zinc neutral leaching stage. In 2003-2004, pilot tests were finished in BGRIMM in cooperation with Fankou Lead and Zinc Mine Ltd. And the extraction rate of Ga and Ge in the leaching stage was 94% and 83% respectively. The total recovery rate was 90% and 80%. It is estimated that the technology has a wide commercial use in the coming five years.

Jan 1, 2006

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By Metehan Erdogan, Furkan Özdemir, Ishak Karakaya, Mustafa Elmadaglı

Tungsten is mainly produced by H2 reduction of WO3 which makes its production difficult and costly. A promising method was recently reported for direct electrochemical production of tungsten from CaWO4 (scheelite) which is estimated as the seventy percent of the all tungsten reserves of the world. This paper investigates the application of pulse current in the electrochemical reduction of CaWO4 pellets attached to a current collector. The electrolyte was composed of calcium chloride and sodium chloride salts at eutectic composition (48 pct mol NaCl at 873 K). The reduced samples were cleaned with dilute hydrochloric acid solutions and characterized by X-ray diffraction and scanning electron microscopy. Examination of the results revealed that metallic tungsten was obtained by pulse current reduction.

Jan 1, 2016

By Wolfgang Steffes-Tun

Pyrite ore concentrate from the Meggen mine (FRG) , which contains about 0 300 400 ppm thallium, is roasted in a fluid bed furnace at 1000 -1100 C to form sulfur dioxide and ash consisting mainly of hematite. Subsequently, the sulfur dioxide is separated from the ash or dust during several steps while cooling to about 250oC. The pyrite ash fractions show decreasing grain size down to 5 pm, a pH-decrease down to 2,4 and a marked enrichment of arsenic and thallium by a factor of 12. In the final fraction, the hot electroprecipitator dust of the dump (EGR), minute crystals of thallium-containing jarosite can be detected by analytical transmission electorn microscopy (TEM). Under oxidizing, acid conditions, jarosite may be a possible "reservoir mineral" for immobilizing thallium.

Jan 1, 1989

By Issa S. AI-Kharusy

Oxidation/reduction (REDOX) alloy media, as used in wastewater treatment, is founded on the exchange of electrons. Because of this electron exchange, many contaminants are converted to harmless components which require no further treatment. Other types of contaminants are removed from the waste stream by electrochemically bonding to the alloy medium. This paper discusses the REDOX reactions, the role of the alloy medium in various treatment processes, and describes specific applications of REDOX alloy media for the removal and minimization of waste. The characteristics and handling of spent treatment media is also reviewed as a further consideration in waste minimization.

Jan 1, 1996

By Adelana Adetunji

Ilmenite ore samples obtained from Dankoli in Zamfara, North Western Nigeria has been characterized using Energy Dispersive X-ray fluorescence (EDXRF) technique, X-ray diffraction (XRD) technique and the Neutron Activation Analysis (NAA) technique. The major constituents in the ore were quantitatively found to be TiO2 and Fe2O3 in concentrations of about 60wt% and 31wt% respectively. These occur in the forms of magnesian ilmenite (Fe, Mg)(Ti, Fe)O3, pure ilmenite (FeTiO3), and barium copper yttrium oxide (Ba2Cu3YO6.56) minerals. Other constituents/impurities in minor or trace quantities include MnO, Ta2O5, Nb2O5, Wo, SnO2, Hf, Zn, V, Zr, Co, Pb, Br, Al, Rb, Y, Th and U.

Jan 1, 2006

By James P. Bennett, Jasper Kwong

As concerns about the environment and the disposal of industrial wastes increase, the utilization of spent refractories from electric arc furnaces (EAF) is receiving more attention. Longer service life of refractories in an EAF can be achieved by foaming MgO saturated slag. The refractory wastes removed from a melt shop can be utilized as a part of these slags. The Albany Research Center is conducting research on recycling spent basic refractory materials as EAF slag conditioners. A good foaming slag should be a creamy, MgO saturated slag, which contains some solid particles (MgO-FeO). A computer model was developed to calculate the dual saturated slag chemistry with respect to CaO and MgO, the MgO saturated slag chemistry, and the solid content in solution. The effects of C/S ratio, AhO3 and temperature on the MgOsaturated slag as calculated by the model will be discussed.

Jan 1, 2000

By Varadajan Seshadri

The increase in production of continuous casting machines requires long ladle sequences without interruption. Very often the production schedule has to accommodate a variety of steel grades. In such cases downgrading may be inevitable. Models must be made available to study the alternatives that would make possible mixing of steels in the tundish but minimizing the losses due to downgrading the slabs. Physical modeling was used to evaluate the influence of variables such as internal geometry of the tundish, presence of turbulence inhibitors, depth of ladle long nozzle, weight of steel in the tundish, steel throughput upon the tundish transition curve. Expressions for minimum residence time and transition period have been determined. Mixing-transition is allowed to continue inside the liquid pool in the mold and the final solute distribution in a given cross section is captured by a solidification model. The result is a map of the transition in the final product.

Jan 1, 2006

By Eoghan T. M Doyle

Oxide mixtures of nickel (NiO), cobalt (COO) and chromium (Cr203) were prepared with graphite in stoichiometric amounts and the powder mixtures were compacted to produce cylindrical pellets. The composition of chromium oxide in these mixtures were varied. Pressed pellets were reduced in a flowing stream of argon-4% hydrogen gas (500 ml/min). Both slow and rapid heating methods were adopted to raise the temperature of a pellet during reduction of oxides to form superalloy powder. The reduction temperature was varied between. 1523 and 1623K. The effect of heating rate and niobium oxide addition on the microstructure of the superalloy produced was studied by using ordinary light and scanning electron microscopes. New phases formed as a result of reduction were identified by X-ray powder diffraction technique. The mechanism of reduction of oxides together with the microstructure of NiCrCo alloy are discussed. The thermodynamics of formation of ternary alloy phase is elucidated on the basis of binary phase equilibria and Gibbs free energy of mixing data for the constituent alloy compositions.

Jan 1, 1992

By V. K. Kalyani

The present paper discusses a three layer feed forward artificial neural network (ANN) model, trained using the error back propagation algorithm, has been established to simulate the column flotation circuit used for beneficiation of Sillimanite. Parameters such as superficial air velocity, wash water rate, froth height, % solid, feed velocity, sodium silicate and oleic cid are considered as process operating variables and % yield of Sillimanite is the output of the experiment. The results from the ANN modeling, involving the non linear relationship between inputs and outputs, indicate good agreement with experimental observations. The network model validates the experimentally observed trends. The optimal model parameters in terms of network weights have been estimated and can be used for computing parameters of the process over wide-ranging experimental conditions.

Jan 1, 2006

By Dewei Zhu

A general purpose computer model for describing the transport phenomena and resulting rate of deposition in Chemical Vapor Deposition (CVD) processes has been described. Partial differential equations describing the conservation of mass, momentum, energy and chemical species are solved by a computer program employing a finite volume method. The program allows for multiple chemical species and natural convection effects. In this paper, the deposition of silicon by the reaction of silicon tetrachloride and hydrogen in a vertical stagnation flow reactor with rotating substrate has been considered. The effects of reactor pressure and substrate rotation speed on the rate and uniformity of deposition have been studied. The predicted rates of silicon deposition along the substrate are in reasonable agreement with experimental results found in literature. The model can be used as a tool for design optimization of such reactors.

Jan 1, 1990

By Jannie S. J. van Deventer

Geopolymers are novel engineering materials with the potential to play a highly significant role in the transformation of the construction materials and building products industry in the push towards sustainable development. These materials are formed by activation of industrial aluminosilicate waste materials such as coal ash or blast furnace slag with alkaline solutions. Geopolymers derived from coal ash can exhibit superior mechanical properties and chemical stability when compared to ordinary Portland cement (OPC). The use of waste-based geopolymers can also result in significant (up to 90%) reduction in carbon dioxide emissions when used in cement replacement applications. In addition to the formation of conventional pre-cast products, these high performance mineral binders are ideally suited to use in the encapsulation of mine tailings, immobilization of heavy metals and back-filling of mines due to their chemical stability and resistance to acid attack. A key attribute of geopolymer technology is the robustness and versatility of the manufacturing process; it enables products to be tailor-made from a range of raw material sources (waste and/or virgin) with specific properties for a given application at a competitive cost. Despite these key technical and environmental attributes, it is the ability to add significant value to coal ash or and/ or metallurgical slag waste streams which drives the commercial development and uptake of the technology.

Jan 1, 2006

By Marcelo R. Esquivel

A MmNi5 alloy is synthesized by a combination of mechanical milling and low temperature heating processes. Synthesis time is 40 h for powders milled in a low energy ball mill at room temperature. A reduction in milling time is obtained if massive sample is mechanically milled at shorter times (2 h to 10 h) and heated at temperatures lower (600 ºC) than the usual temperatures used in equilibrium methods (>800 ºC). The alloy formation is detected even at a combination of temperatures as low as 200 ºC and milling times as short as 5 h. The temporal evolution of mechanical milling process was followed by both X-ray diffraction (XRD) and scanning electron microscopy (SEM) to detect the main stages of milling. Four stages were detected: Initial, Intermediate, Final and Completion. These stages were correlated to an enhancement of the synthesis method by combination of times of milling shorter than 10 h and temperatures of heating lower than 600 ºC.

Jan 1, 2006

By Dirk Verhulst

The Altair process employs digestion of ilmenite ore in concentrated hydrochloric acid, solvent extraction to concentrate Ti in a purified stream and spray hydrolysis to produce a TiO2 hydrate, followed by final calcining and milling. HCl gas is regenerated by pressure-swing distillation and reinjected in the leaching solution. All chloride streams are recycled. Chromium compounds generally remain in the residue. Solvent extraction provides flexibility for the removal of naturally occurring radioactive elements (NORMs) present in some ilmenites. The process was previously tested at a 5 t/day feed scale. Recent work at pilot scale (40 liter reactor) led to further improvements. Recovery of Ti in solution is now at least 90% with ilmenite ores, while crystallization at lower temperature lowers the amount of Fe in solution to about 5 g/l and improves solvent extraction, which is now conducted in columns. Higher Ti and lower Fe concentrations in the SX eluate improve the economics. A new formula for pigment production via spray hydrolysis produces a pigmentary base with a narrow particle size distribution.

Jan 1, 2003

By Andrey Dmitriev

The solution of set of equations for the bottom zone presented by a condition of a thermodynamic equilibrium, namely, an equilibrium constant of wustite reduction by carbon oxide, material and thermal the balances, supplemented by the equation of the heat balance for the top zone, allows to calculate the base indices of blast furnace smelting. The calculated indices are extreme accessible at the given parameters of charge and blast. Application of actual degrees of the use of gas instead of equilibrium allows the calculations of actual indices of the blast furnace smelting process.

Jan 1, 2006

By Jesse White, Arlin Olson

"An Engineering Scale Technology Demonstration (ESTD) unit utilizing the THOR fluidized bed steam reforming technology was built and operated by Hazen Research, Inc. for the purpose of denitrating and solidifying various Department of Energy (DOE) radioactive tank waste surrogates into granular products. The ESTD offered the opportunity to investigate the operational characteristics of two fluidized beds in series to test process system designs such as those for fluidization, feeding, and product collection. Operational characteristics that were evaluated included bed attrition rate, particle growth, and elutriation; and the effects that variations in process parameters (e.g., fluidizing gas flow rate, feed composition, feed injection method, and gas distributor design) had upon these characteristics were observed. Testing of the process systems on this scale allowed for design changes to be made where the cost in time and money were significantly less by comparison to those same modifications being made on the commercial scale.IntroductionFluidized bed steam reforming (FBSR) offers a moderate temperature (620-750°C) continuous method by which various liquid wastes can be processed irrespective of whether they contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology has exhibited the potential to process these wastes into either a carbonate or crystalline ceramic (mineral) granular product.Pilot scale testing was performed using the THOR Treatment Technologies, LLC (ITT) FBSR process, as it offered the opportunity to evaluate multiple aspects in an environment more conducive to experimentation. Process changes and system modifications could be made faster and with less cost impact as compared with changes to an assembled commercial plant. These aspects include verification of process chemistry and kinetics, evaluation of materials of construction, equipment sizing and design, and the interactions of the systems. Evaluation of process chemistry allowed for the verification of thermodynamic and kinetic models, and was used in conjunction with these models to improve the database and modeling assumptions. It also allowed for the reevaluation of data from earlier bench scale testing with the opportunity for long-term operations. These long-term effects may include the buildup of one or more elements that results in the formation of eutectics leading to the destabilization of a fluidized bed, or the shift in particle size as a result of attrition or agglomeration. The pilot plant also provided an environment to evaluate materials of construction."

Jan 1, 2014