Search Documents

By Jon C. Volkwein

The U. S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography at the Pittsburgh Research Center. These gas results were analyzed for explosibility. Personal exposure to carbon monoxide was also monitored. The highest methane level observed was 9.55 pct. The Inert gas levels, (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were non-explosive. The maximum personal time weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining. INTRODUCTION The auger highwall mining method is an effective method to recover coal from a reserve when removal of the overburden by surface mining equipment becomes uneconomical. In this method of mining, a horizontal auger enters the coal seam from the surface mine bench under the highwall and the coal is drilled in a series of parallel holes. Historically, coal mined from the surface is relatively shallow, and over time, methane associated with the coal has dissipated through the surface. In most circumstances, little methane has been found associated with auger mining. However, mining technology has enabled surface mining of deeper reserves of coal. Furthermore, environmental constraints have forced the highwall extraction method to be used to remove coal under wetlands, further increasing the chances of encountering methane. Recently incidents of methane explosions at a few auger mining operations have resulted in injuries and increased testing for methane at the collars of auger holes. The fuel source of the reported explosions was not necessarily limited to methane, but may also have involved coal dust. The Mine Safety and Health Administration (MSHA) met with the Bureau to discuss what technology might be available to enable the safe resumption of mining. The discussion included the difficulty of ventilating through the solid shafts of the augers, that steel bits probably created the ignition source, and that perhaps inerting the holes with low oxygen and high carbon dioxide concentrations from the machine's diesel exhaust was a potential solution. Considering the ventilation aspects of the problem, it was not clear If ventilation could be reliably established. If some degree of ventilation to the front of the mining head is achieved, it may combine with methane to bring the hole atmosphere from a rich, nonexplosive mixture to an explosive mixture. Furthermore, it may not prevent a dust explosion in such a mining configuration. Lack of access through the shafts of auger type mining machines further limits the ability to add water or air to cool bits to prevent an ignition source from developing. Either of these approaches would also be expensive. The process of mining coal In an inert atmosphere has been considered in the past, but to our knowledge, never implemented (Department of Interior, 1970). Clearly, implementation in underground mining would be more complicated. On a mine bench open to the atmosphere, however, adding inert gas to the mining head could provide a quick, feasible method to prevent explosions at auger highwall mining operations. Also the problem of how to move the inert gas to the cutting head of the machine had to be considered. Preventing explosions on auger mining machines using inert gas requires three primary considerations: first is the source of inert gas; second, placing the inert gas at the cutter head; and third, monitoring the hole atmosphere. Any gas source having an effective inert gas concentration of 34 volume pct or greater will prevent methane from Igniting (Zabetakis, 1965). Sources of inert gas considered for this application included liquid nitrogen, modified shipboard inert gas generators (for hydrocarbon shipping and transfer), jet turbine engine (Paczkowski, et. al., 1982), the auger's diesel engine and a gasoline engine. Operation cost, purchase cost and availability limited our testing to the diesel and gasoline engines. This work tested each engine, separately and combined. To ensure effectiveness, both company and enforcement personnel need to know how to monitor the condition of the inerted hole. Measurements at depth inside the hole are possible by remote sampling through rigid tubing, but this method is Impractical for routine monitoring. Continuous monitoring of the exhaust gas stream is an alternative. The U. S. Bureau of Mines evaluated an inert gas system at an auger mining operation at a surface mine near Owensboro, KY. Coal was mined from the Number 9 Coalbed in Henderson Co. KY. Tests were conducted in January and March of 1992.

Jan 1, 1993

By O. J. R. Baena, I. C. Sánchez, J. L. G. Guzmán

Frontino, a municipality in western Antioquia, Colombia, has more than 200 years of mining tradition. Currently, mining activities are carried out for lode gold using subway tunnels, where the grinding of the material is done in "cocos", whose energy depends on internal combustion engines and ACPM, environmentally polluting and inefficient methods. In accordance with the Sustainable Development Goals as an initiative developed by the UN, different mining methodologies that are aligned with these are constantly being analyzed. This study proposes to eliminate the use of hydrocarbons in artisanal mining, mainly promoting Sustainable Development Goals 7, 9, 11, 12, and 13. This will be achieved through an energy transition to renewable energy sources that take advantage of the topography and water resources of the area, providing advantages to the communities that live there, such as lighting, electricity for cooking, ventilation for mines, etc

Mar 2, 2022

By Charles P. Lazzara, Alex C. Smith, Mark W. Ryan

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple entry section of the Bruceton Experimental Mine. Chambers filled with one hundred and eighty kilograms of Pittsburgh seam coal were ignited and allowed to burn until well developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires and the quantity required to extinguish the fires compared to the amount of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 22 L to extinguish the coal fires, while two commercially available additive-water solutions required an average of 30.6 and 30.3 L, respectively. The average amount of water required to extinguish the fires was 28 L. An analysis of covariance, using the thermal energy of the coalbed, Q, to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, while the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 1992

By Ajay K. Singh

The surface quality demands for galvanized and galvannealed steel sheets by the automotive and appliance industries have been getting increasingly stringent over the past few years. Intensive efforts by Hot-Dip-Galvanizers to meet these demands have resulted in substantial improvement to the hot dip coating process. However, elimination of zinc bath contaminants which directly affect the coated strip surface quality continues to remain a tough challenge. As part of our effort to improve the zinc bath cleanliness, Inland Steel Company has developed a test method to quantitatively measure the contaminants in incoming zinc spelters and establish a specification for incoming zinc quality. The test is currently being used for auditing the incoming zinc quality. The zinc suppliers are also using this test for quality control purposes. The purpose of this paper is to describe the test method and how it has improved the galvanizing operation at Inland.

Jan 1, 1992

By M. A. Oskouei

Draglines are dominant machines and the most electricity consumers in surface coal mines. With the growing price of energy, environmental concerns, and the high sensitivity of mine profitability to dragline productivity, any improvement in efficiency of draglines can be beneficial for mines. Research has shown that operator skills have a significant impact on energy efficiency of loading machines. This study suggests a method to identify the key parameters that lead to differences in operator energy efficiency (responsible parameters). First, correlation analysis is used to identify parameters that are correlated to energy efficiency. Second, linear regression of a difference matrix is used to determine responsible parameters. Since this method is based on pair-wise comparison of operators, equal number of cycle is required for pairs of operators. Complete case analysis (CCA) is used to handle missing data problems. The final conclusion is made after removing the effect of random sampling and by considering all pairs of operators. Identifying responsible parameters can improve operator training programs. The suggested method is illustrated with a case study using field data.

Feb 23, 2014

By Nikolaos Petropoulos, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature. In this study, pure emulsion was tested in confined conditions to better simulate the behavior of the detonation of the explosive in rock mass conditions. A methodology is proposed for carrying out the evaluation of the explosive performance. The blasthole diameter of the samples varied from Ø 25 mm (0.98 in) up to Ø 65 mm (2.55 in). The confiner was a magnetic mortar cylindrical sample with mechanical properties similar to a rock mass. A streak camera and VoD probes were used to measure detonation front curvature and VoD. The data was analyzed and correlated with the physical parameters of the explosive. Additional to this, the data was further used to calibrate numerical models in LS-Dyna.

By Nikolaos Petropoulos, Ulf Nyberg, Ulf Stenman, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature.

Feb 1, 2020

By M. M. Moghaddam

Charge motion is of prime importance in the efficiency of comminution in tumbling mills. Since direct observation of charge shape and its motion in industrial mill are not possible, a combination of analytical and physical studies was used to determine charge trajectory. Software packages, which predict charge motion such as the GMT (Grinding Media Trajectory) only consider the outermost layer of charge (single ball) and ignore the interactions of grinding elements. In this research, the measured charge trajectory in a 1m-diameter mill with the transparent end, called model mill, was compared with that of the GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. To explore various charge shapes and trajectories, the model mill was operated at 55, 70 and 85% of critical speed for five levels of mill filling (10, 15, 20, 25 and 30% by volume). The angular displacement of the toe, toe departure, shoulder and charge impact point were determined from the photographs taken from the model mill. New relationships to predict charge shape and charge impact points were introduced to modify the GMT results. The relationships were validated by the model mill using the new liner of the Sarcheshmeh copper complex SAG mill. The relative error of prediction was found to be 1.1%. The results indicated that when the lifter face angle increased from 7 to 30º, the distance between the charge impact point and the toe decreased from 52 to 31º for 25% filling. This meant increasing the probability of charge impacting the toe not the liner which favoured more efficient comminution practice. After converting AG mills to SAG mills on account of liner profile change, 31% increase in throughput (from 419 to 548 t/h) in addition to 4% decrease in the product size (from 516 to 496 µm) were realized which was a significant contribution in the plant performance improvement.

Sep 1, 2012

By M Simpson, K Brodie, J L. Mauk

Subaqueous water-rock reactions that occur at the pit wall/lake water interface can affect the pH of pit lakes. Many pit lake water chemistry models neglect subaqueous reactions, which may create inaccurate predictions over time. A mineral quantification method is presented that defines the wall rock mineralogy of active open pit mines, using samples collected from the Martha Mine, a low-sulfidation epithermal Au-Ag deposit in Waihi, New Zealand. The mineral quantification method has five components: field observations and sampling, X-ray diffraction analyses, selection of representative samples, geochemical analyses, and mineral accounting. Predicted mineral concentrations closely match observed mineral concentrations visually estimated using petrographic techniques. Results of the method can be incorporated into a geochemical model of long-range pit lake water quality resulting from subaqueous water-rock reactions.

Jan 1, 2003

By C J. Berry, P H. Briggs

Assessment of metal mobility, acid rock drainage production, and toxic effects from weathering of mineralised materials (ie mine-waste piles and outcropping alteration/ore zones) is key in evaluating and mitigating metal mining sites. Many metal- and acid-generating materials at these sites are sulfur minerals (sulfides to sulfates) with differing reactivities, weathering characteristics and metal contents. Our working hypothesis predicts that data on the types and quantities of sulfur minerals, coupled with comparison of their sulfur isotopic compositions to that of aqueous sulfate in the surrounding environment, can be used to evaluate primary pathways of weathering reactions at mining sites. We developed a sequential extraction scheme to separate the phases of sulfur in mineralised materials. Operationally defined phases, including monosulfides, disulfides, elemental sulfur, water-soluble sulfo-salts, acid-soluble sulfates, and resistant sulfate phases such as barite, are quantified gravimetrically and/or instrumentally. Several sets of experiments were designed to test the effectiveness of this extraction scheme. First, a variety of ore sulfides diluted in an inert matrix was analysed with the scheme. Results showed that molybdenite and arsenic-bearing sulfides do not behave as predicted from just their sulfur oxidation states, indicating that samples containing these minerals need special treatment for complete phase recovery. Second, a natural mine-waste composite standard was analysed by the scheme. The sum of the phases was equal to the total sulfur concentration analysed independently. Each phase had a similar, but distinct sulfur isotopic composition. The results were verified with a laboratory prepared æproxyÆ having the same mineralogical composition as the standard, but with each phase having a very different sulfur isotopic composition. The sulfur isotopic compositions of the recovered phases from the æproxyÆ showed that the scheme effectively separated the sulfur with only minor cross contamination of phases. The speciation and isotopic analyses were applied to both mine-waste piles and naturally occurring alteration zones at nine mine sites. A case study from one site comparing the sulfur isotopic composition of minerals in an alteration zone and dissolved sulfate in proximal streams is presented. This case study shows the application of our data to differentiating sources of sulfate in the surrounding environment.

Jan 1, 2003

By B. Erdem, N. Çelebi

An important problem associated with tandem dragline systems is that of matching the productive capability of individual draglines in the combination. In this paper, a dependence mechanism among draglines in a tandem system is described, and possible consequential problems in a poorly-matched system are defined. The rate of linear advance and the cost of stripping are determined as two major indications for an efficient operation. The proposed decision criteria and the underlying mechanism to select a synchronous couple are introduced and used in simulating tandem dragline systems. The developed model is tested on a hypothetical strip mine where pullback stripping is applied with a tandem dragline system.

Jan 1, 1999

By M Ruhrberg, J Grassmann, C Bauer

Within the context of acid mine drainage (AMD) associated with mining activities worldwide there has been a tremendous research effort to determine the extent of AMD and assess the influencing factors controlling this process. However, the majority of the current approaches focus on local and regional scale case studies and do not provide a global scale picture of AMD potentials. This study attempts to develop a method aiming at a global environmental impact assessment related to AMD. To confine the complex topic this study concentrates on acidic emissions from heaps in consequence of copper mining processes. In order to pursue this approach two factors are of significant advantage: a comprehensive environmental data base of more then 600 copper sites worldwide and a method which has been developed and proven to be successful in assessing environmental impacts related to land use. Current and future research efforts focus on using this background knowledge to enable both a comparison between sites and a categorisation of sites according to emission estimates.

Jan 1, 2003

By J. A. Botín

Identifying, quantifying and minimizing technical risks associated to investment decisions is a key challenge for the minerals industry decision takers and investors. However, risk analysis in most bankable mine feasibility studies are based on stochastic modelling of project NPV which, in most cases, fail to provide decision makers with a truly comprehensive analysis of risks associated to technical and management uncertainty and, as the result, are of little use for risk management and project optimization. This paper presents a value-chain risk management approach where project risk is evaluated for each step of the project lifecycle, from exploration to mine closure, and risk management is performed as part of a stepwise value added optimization process.

Jan 1, 2011

By S Tierney, D Cumming-Potvin, I Thin, Y Potvin, D Grant

The preliminary modifying factors for future stope design in the Southern Mine Area of Olympic Dam consisted of only a single, arbitrary value of Equivalent Linear Overbreak/Sloughing (ELOS). In order to improve this, a study was conducted which developed a more comprehensive methodology for assigning ELOS, Equivalent Linear Lost Ore (ELLO) and Equivalent Linear Fill Overbreak (ELFO) to individual stope faces based on geotechnical and mining parameters. The approach used was to look at the simple cases, which were classed as vertical stope walls in good ground (RQD 80-100%), divided into wall orientations (North, South, East, West). The stope walls were also split based on the blasting practice used (toeing, parallel or a combination of the two). The expected ELOS and ELLO from these ‘base cases’ are then modified by parameters which have historically been found to affect stope performance (Hydraulic Radius and Q’). The size of the effect found in the historical data determines the ELOS / ELLO applied. The methodology was summarised in an easy to use flow chart and was applied to all of the proposed stope shapes for the Southern Mine Area and summarised per mining block. This allowed each iteration of the mine plan to be assessed in terms of overbreak (both rock and vertical fill exposures) and underbreak.

Mar 15, 2021

By E. Kumar, L. A. Kumar

"A methodology is proposed to develop an optimization model to understand the impact of transporting minerals, from mines to the final destination, on air quality. Recently, there has been increasing concern about the combined effects of multiple activities over many years, and the regional environmental changes brought about by a single project. Environmental issues in the iron ore industry have highlighted the need to broaden the cumulative impact assessment. In this study, we simulated the optimal routes and quantity of materials needed to meet the destination plant demand based upon environment constraints (level of air pollution), as well as the cost of transportation and availability of materials. Multiple scenarios were developed to analyse the effects of changes in routes, alternative transport system (or multi-modal split), traffic congestion, and the cumulative impacts on air quality. The air quality impact zones of the study area were demarcated using a GIS technique. The expected outcome of the study is the selection of a suitable transport system for a particular site with the least impact on air quality, including the transportation route, relative to the minimum cost of transportation of the minerals from the mines to their final destination. The proposed methodology is evaluated with a case study. IntroductionIn India, the process of environmental impact assessment (EIA) has been focused primarily on the local impacts of projects, without considering regional environmental effects. Environmental clearances for proposed projects are based on reports of local impacts. However, any developmental project poses a potential risk to the environment as a whole, and not just in the immediate vicinity of the project. Recently, there has been increased concern about the combined effects of multiple activities over many years—the regional environmental changes due to development of a single project (Dutta, Mahatha, and De, 2004). Environmental issues throughout the country, particularly in the iron ore industry, have emphasized the need to broaden the analysis to include the combined impacts, or those forecast for a proposed region, on an existing environment. The most significant adverse environmental consequences of iron ore transportation are the deterioration of biodiversity and air quality (Kumar and Ajay, 2015)."

Jan 1, 2017

By Pedro Marques Bernardo, Carlos Dinis da Gama

This paper presents a methodology for design and simulation of underground ventilation networks, based on the analysis of real situations, followed by the careful interpretation of the obtained results in order to implement their optimization. The method involves two basic steps: the construction of a complete ventilation data base for the mine, upon a series of care- fully previous surveying studies in order to determine the values of its ventilation parameters, and the simulation of relevant situations for the ventilation system optimisation. A simulation model, modified after the Hardy Cross method, allows the testing of various mechanical means located at different points of the network, aiming to determine the technical-economical feasibility of each solution. These simulations obey the directions of air flow in each point of the mine, as determined by the directions of the natural ventilation flow established in the data base that represents the network. The methodology was validated upon studies developed in ventilation network of the Panasqueira Mine (Portugal), in two situations: regular production (mechanical ventilation) and care- maintenance (natural ventilation).

Jan 1, 1997

By G. Esterhuizen, C. Karacan

Methane can be a significant hazard in coal mine longwalling operations and extensive methane mitigation techniques are employed by coal mine operators. Reservoir modeling techniques are used to better understand the liberation and migration of methane from the surrounding rocks towards the mine ventilation system. The caved rock behind the advancing longwall face, known as the gob, can contain high void ratios, providing high permeability flow paths to the methane. The gob is progressively compacted by the weight of the overburden, resulting in a reduction in the void ratio and associated permeability. Estimating the permeability distribution within the gob poses challenges due to its complexity. The authors have developed a new methodology to determine both horizontal and vertical variations in the permeability of the gob. Variations of the permeability in the vertical direction are based on a model of caving and block rotation, which considers the effect of block dimensions and fall height on the void ratio. Gob compaction by the overburden and associated permeability changes are determined from a three-dimensional geo-mechanical model which simulates the gob as a strain hardening granular material. The resulting three-dimensional permeability distribution in the gob is then transferred to a reservoir model. The paper demonstrates the application of the method and shows that reasonable results are obtained when compared to empirical experience and measurements.

By H. Dong

This paper presents a heat conduction model to determine the erosion profile of freeze linings in a ferronickel submerged arc furnace. Kirchhoff transformation was adopted to simplify the nonlinear equation governing heat conduction. The boundary element method (BEM) and Nelder-Mead simplex optimization method were employed to solve an inverse heat conduction problem. Erosion profiles could be obtained when calculated temperatures at sensor locations agreed well with measured temperatures. The model was validated by comparing the heat loss through the linings, which was calculated by BEM and integral operation after erosion profiles were obtained, with the value calculated from industrial data such as actual power consumption, tap-to-tap time, and ferronickel output. The optimal solution for the erosion profile could be acquired when the difference in heat losses calculated by these two methods is at a minimum.

Jan 1, 2014

By H. Kim, R. W. Plummer, T. J. Stobbe, W. G. Jones

"Exposure to airborne dust in coal mines has caused respiratory disease in coal miners. The causal agent in these diseases remains unknown, although the minerals found in and around the coal seam have been implicated. Toxicological studies designed to establish the effect of different mineral combinations and concentrations are lacking because the mineral content of coal mine dust has not been defined. This paper reports the initial results of a study done to characterize the mineral content of the coal mine dust found in a mine in the Upper Freepott seam in Northern West Virginia. Coal mine dust samples were collected using 4- stage cassette impactors at nine locations in the mine. The samples were analyzed by an x-ray microdiffraction film technique supplemented by energy dispersive scanning electron microscopy. Primary size modes of about 17 to 20 micrometers from the samples collected at the haulageway and the returnside of the continuous miner were found. From the returnside of the roof bolter samples, a primary size mode of 12to15 micrometers was measured. The minerals found in high percentages were illite, kaolinite, quartz, and calcite. The distribution of minerals in inter· and intra- location samples showed wide variations. Trends in these variations are presented. Stobbe, T. J.; Plummer, R. W.; Kim, H.; Jones. W.: Characterization of coal mine dust. Appl. Ind. Hyg. 2:95· 100; 1986. IntroductionDisease-associated dusts in coal mine environments continue to afflict miners in today's modern mines. The relationship between exposure to coal mine dust and the development of various respiratory diseases has been well recognized; however, the reasons for variation in occurrence of these diseases among miners in different geographic areas,(1) rank of coal seams,(2-3) and jobs (4) remain uncertain. Several papers have reported on the causal agent in the development of these diseases. Davis (5) found that the percentage of the non-coal minerals present in the lungs of deceased miners increased as the level oi pneumoconiosis became more severe. Reisner (6) reported that cell damage caused by coal mine dust increases with the mineral and quartz content of the dust and with the geo· logical age and rank of the coals. Two studies, investigating the in vitro effects of mineral dusts. reported by Seemayer and Manojlovic (7) also obtained positive correlation between cytotoxicity and the mineral content of coal mine dust. Gormly (8) postulated that destruction of macrophages by certain mineral dusts is the first step in the development of pneumoconiosis. In 1980, Adamis and Timar (9) reported that quartz. sandstone, slate. respirable colliery dust. bentonite, illite, and some kaolins had cytotoxic effects on rat peritoneal macrophages""in vitro."" Walton,(10) however, reported that the presence of high clay, illite, and kaolin mineral exposures reversed the hazards associated with increasing quartz exposures. This finding was supported by Le Bouffant and coworkers.(11) They reported that illite present in coal mine dust strongly inhibited the pathogenic effects of quartz while kaolin had a weaker inhibitory effect."

Mar 1, 1989

The investment worth of a mineral deposit can only be realistically evaluated in relation to specific engineering design criteria, which fully details the proposed method of exploitation. These criteria have not in general been taken into serious consideration when leaseholders have reported reserves in the past. In fact, many "reserve" figures quoted are probably more correctly classified as geological resources. The industry now recognises that it is necessary to take into consideration not only grade and mill recovery factors, but also likely mining and processing costs as well as the current market price for the commodity. Once having estimated those costs which are applicable to the resource under study, they can be deducted from the gross inherent worth of the orebody to result in an estimate of the potential net revenue. Through a process of interactive trial mine designs and evaluation, reserves can be quantified to provide an estimate of the available recoverable economic reserves given a set of assumed cost and operational parameters. It follows then, that the available economic reserve recoverable from a given resource will vary from time-to-time as cost and price factors vary in response to changing technology and economic factors. A methodology is described which may be used to derive economic recoverable reserves based on a computerised model of the geological resource data and appropriate economic and operational cost algorithms. Examples are provided from both coal and gold studies to illustrate the impact of economic criteria on the magnitude of the reserve figure reported for each project.

Jan 1, 1987