Search Documents

By S. B. Patton

A computer model, which quantitatively utilizes the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation, is presented. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation, and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasification on the ventilation system in a longwall panel.

Jan 1, 1992

By Byron S. Gottfried, Guan Qi Zhao, John W. Tierney

Equations for predicting the performance of vacuum filters and centrifuges used for coal dewatering are presented. These equations are the basis for a dewatering module which has recently been added to the Coal Preparation Plant Simulator developed at the University of Pittsburgh under the sponsorship of the Department of Energy. The module provides for mechanical degradation in the centrifuge; loss of fines to centrate or filtrate; changes in size and gravity distribution; changes in ash and sulfur content; as well as final moisture content of the dewatered product. Inputs to the module are the flow rate of the coal to be dewatered, a washability analysis of the coal, and parameters describing the operation of the vacuum filter or centrifuge. Typical results obtained using the module are presented. There are adjustable parameters which can be varied to match plant operation or experimental data if desired.

Jan 1, 1983

By S. F. Burks

"This paper develops themes explained at two SAIMM platinum conferences. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can be increased significantly, usually even before the expenditure of significant amounts of project capital. Recent studies of NPV have aimed to simultaneously evaluate the impact of the optimized financial solution on the non-financial features of a project or operation.The case study presented comprised a commercially orientated review of the prefeasibility study designs and cost estimates of a platinum group metal (PGM) project in South Africa, followed by value chain optimization and sustainability studies of the project carried out simultaneously to identify potential value uplifts to be gained and guide the owners’ team going forward into the feasibility study phase. Some of the major aspects of the project that were found to have significant potential to add value included enhancement of the business model by the application of activitybased costing and theory of constraints, focus on the highest net value portions of the orebody in the early years of production, enhanced and optimized scheduling of the underground mining operation, application of dynamic grind and percentage mass recovery from ore to flotation concentrate (also known as percentage mass pull) to optimize revenue, application of elevated cut-off grades early in the life of mine, matching of the mining and processing capacity, expansion of the operation subject to capital availability, and installation of downstream processing facilities subject to regional third-party capacities.The investigation of non-financial project features focused on demonstrating that a financially optimized solution could also have a number of other benefits. These are mentioned briefly in the paper, which aims to present the status of the project at an early stage of its development."

Jan 1, 2016

By Y Ren

The algorithms employed by the commercial tools are either heuristic algorithm or iterative optimisation of a subsystem. This often results in a suboptimal schedule. In this paper, the author presents a new scheduling algorithm that incorporates with a novel stockpile configuration system, an improved algorithm on multiple processes and a mixed-integer linear programming (MILP) global optimisation model. It can simultaneously optimise stockpiles, blending, multiple processes as well as multiple mines. In addition, it allows the user to interact with the solution to adjust the solution to be practical and desirable.CITATION:Ren, Y, 2013. A simultaneous optimisation tool for open pit mine scheduling, in Proceedings World Gold 2013 , pp 427-432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

By Lee F. Robinson, Angus W. Morrison, Norman M. Anderson

About 100 years ago the acid and chlorine oxidation routes for gold extraction were abandoned in favour of cyanide/ oxidation processes. Now a return to acid processing is in progress. One publication in particular led HM C Technology to investigate the reaction of dilute nitric acid and alkaline metal chlorides with refractory gold ores.(l) The one stage system of gold and silver recovery from sulphidic ores is described below. It is rapid and does not use large or expensive plant or special pressure equipment. It eliminates calcining followed by cyanidisation and shows a simple way of recovering the gold directly. Patents have been granted in some countries (2).

Jan 1, 1990

By K. S. TWITCHEEL

THE different lines leading out from the vocation of a mining engineer are,' perhaps, the most' varied of all the professions. The expedition sent by Charles R. Crane of New York 'as a gift to the Imam Yahia, king of the Yemen, Arabia, was probably unique. Mr. Crane made a visit, in January,1927, to the Imam Yahia at Sanaa, capital of the Yemen. He was received with the utmost cordiality and respect, as his friend- . ship for the ,Arab world is famous; He was 'greatly impressed by the desire of the Imam to develop his country. The Imam stated that he had heard that there were minerals in his country and that he would like to secure engineers to advise him about them and other natural resources.. This seemed such a practical idea, and so greatly appealed to Mr. crane, that he offered to furnish an engineering 'expedition. Naturally the Imam gratefully accepted. This expedition was to study (as far as possible in 'the limited time) the natural resources of the ,Yemen, advise the Imam of what these consisted, and make suggestions regarding the most practical methods for their development. As agriculture is always such a fundamental part of a country's wealth, I first went to Indio, California, to study water-well drilling and the date industry, and eventually arrived at Hodeidah, the principal Yemen seaport, on Oct. 21, 1927.

Jan 1, 1929

By Jing-she Li, Hai-yan Tang, Cheng-song Liu, Wei Liu

"In order to effectively utilize cheap and low quality iron ores, a hematite ore in a certain steel plant in Xinjiang was researched on to obtain ""iron increase and silicon reduction"" by ore dressing operation experiment and the performance indexes of the hematite ore were optimized. Based on the fundamental characteristics and high-temperature properties of the concentrate after ore dressing and other five kinds of iron ores which were co=only used in this steel plant, ore matching principles were proposed and a sintering ore blending optimization model was established. Finally, sinter pot test was carried out to verify the validity and practicability of the sintering ore blending optimization model which was aimed at giving consideration to the sintering indexes and the cost.IntroductionIn recent years, the price of imported iron ore with high quality is always at a high level, while iron ore self-sufficient rate in China is less than 50%. Enormous market demand and high dependence of domestic enterprises on imported iron ore makes the price of it hardly return to rational. In order to get rid of the situation of long-term meager profit and even deficit, more and more iron and steel enterprises in China transit their focus of reducing production cost to the utilization and development of relatively cheap but low-grade iron ore resources at home[l-4l_ However, besides the disadvantages of low iron grade, high content of impurities and complex embedded properties, the high-temperature properties of iron ore often go beyond the suitable ranges for producing sinter with high quality. Thus directly utilization of this kind of iron ore without ore dressing process would probably affect the metallurgical performance and indexes of sinter ore.Previous research and production practice have shown that traditional iron ore matching in sintering mainly focus on the reasonable collocation of properties of iron ores with low quality and high quality, but pay less attention to ore dressing process of low quality iron ores and matching them with high quality iron ores. Actually, compare with directly utilization, iron ores with low quality after ore dressing have higher suitability for matching with high quality ones which is beneficial to reduce the consumption of iron ores with high quality and control the production cost of sintering [5-s1."

Jan 1, 2014

By W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphalerite and dolomite, has been used to experimentally validate the model for the case of dry, batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1986

By A. J. Basu

An overview of the evolution of computerized mine planning and design has been given, emphasizing the need for a knowledge-based system for planning and design of underground coal mines. An outline for the development methodology and procedure has been provided. Problem structuring guidelines have been used to incorporate intelligence and integration to the design modules. A skeletal model for a mine planning and design expert system has been prescribed, and the development process has been documented in detail. A feasibility prototype has been developed to test the structure of the skeletal model and to ensure completeness of the design process. The feasibility prototype development and its contribution toward proto typing has been addressed in this paper. At present, prototype development is underway. The prototype is expected to be avail-able for testing and implementation in early 1991.

Jan 1, 1991

By K. D. Eigenbrod

A case history is presented of a landslide that occurred adjacent to a highway in the valley of the North Saskatchewan River, about 12 miles upstream of Edmonton, Alberta. The slide took place in the late fall of 1965 following excavations associated with highway improvements that deepened the slope and cut it back to 20º. The slide occurred in the Upper Cretaceous Edmonton Formation. Till covers the bedrock at the location. The bedrock consists of interbedded mudstone, claystone, and sandstone with layers of bentonite and coal. The field investigation consisted of a series of pits at the toe of the slide and seven boreholes around it. Undisturbed samples were taken with a Pitcher Sampler and piezometers were installed at various depths in the section. The slide had taken place on a horizontal bentonitic clay layer and it crossed softened mudstone in the back slope. Three piezometric levels were detected but no water pressures were found along the horizontal portion of the slip surface because it was in contact with a free-draining coal layer. Borehole evidence revealed that the bentonitic clay layer was sheared in place beyond the confines of the slide zone. Although this slide was a first-time occurrence, it was part of a much larger slide block that moved presumably when the valley was being formed. Laboratory tests were carried out to determine the shear strength parameters of the bentonitic clay and the back slope material. These parameters together with the observed water pressure distribution in the slide area gave a factor of safety of 1.01 in a non-circular limiting equilibrium analysis. The case history is particularly instructive in indicating the care that must be taken to obtain representative information for stability analysis when geological and groundwater conditions are non-uniform. The origin of the sheared clay is discussed.

Jan 1, 1972

By W. E. Gaby

THE form of dip chart here presented for the use of the profession was devised by the author when he was confronted with a particularly heavy job of geological section making and. did not have any of the usual tables or charts at hand. This was at the property of the Teziutlan Copper Co. in Puebla, Mexico, where the orebodies are much faulted and lie conformably with a slightly inclined and. much folded schist. Because of the low dip and the folding of the orebodies, the engineering, and geological data respecting them were best represented on vertical cross-sections quite closely spaced. A less finished form of the chart was published in the Mining & Scientific Press of Aug. 6, 1921, with an explanation of its use. I have checked the new drawing for accuracy against the calculated table given, and constructed an explanatory diagram beneath. As some geologists are accustomed to using the table, I have included it, since no advantage is obtained by mere interpolations from the chart to get the required angle, except as it gives a mental picture of this angle. The chart gives a more rapid and much easier solution when cases multiply so that it becomes desirable to eliminate the tedious manipulations of a separate protractor. In fact, using the parallel ruler as des-cribed, it is not even necessary to make note of the angle sought. It is brought out graphically, leaving the mind free to note the correlations. The chart itself may be made more convenient by reproduction on celluloid with a slot running on the zero line of the protractor.

Jan 9, 1922

By V. L. Franzen, Z. J. Hladysz, C. A. Kliche

The Wharf Resources mine, located in the Bald Mountain Mining District approximately 6.4 km (4miles) west of Lead, South Dakota, has operated a surface gold and silver mine and heap leaching processing facility since 1983. Wharf Resources intends to mine and process gold and silver ore from the Wharf Expansion area which is located on the eastern flank of the currently permitted Foley Ridge Mine. The Trojan Pit for the Wharf Expansion area was initially designed with an overall highwall slope angle of 45o. During mine permit presubmission meetings with personnel from the SD Department of Environment and Natural Resources (SD DENR), the question arose as to whether a detailed slope stability analysis of the proposed Trojan Pit highwalls was completed to justify the 45o slope. Wharf’s response was that the highwall design was based, in part, upon studies completed in1987 on the Annie Creek and Foley Ridge Mines; and, in part, upon subsequent slope stability analyses conducted by Wharf mine personnel through 1996. It was suggested by the SD DENR that the stability study be updated to reflect structural geological conditions in the Wharf Expansion area.

Jan 1, 2000

By Anthony D. Hammond, Charles A. Kliche

A slope stability study for the Annie Creek and Foley Ridge Mines was undertaken to provide Wharf Resources, Inc. with a technical assessment of the stability of the slope for an overall pit slope angle of 60°. A rock analysis of the most critical and persistent combination of discontinuities was carried out using probabilistic methods. A detailed discontinuity mapping and assessment of the rock mass provided the orientation data used in this study. The orientation data were reduced and analyzed to identify the discontinuity sets. A statistical analysis provided information about the distribution of the data. A deterministic wedge stability analysis identified the critical combination of discontinuities; those with a low factor of safety were further studied using probabilistic kinematic and kinetic stability analyses. The results from this approach were used to obtain the reliability or probability of failure of the slopes.

Jan 1, 1988

By Brian E. Gombos

During early stages of the detailed design for Detroit?s Upper Rouge CSO Tunnel Project, a Value Engineering Recommendation suggested the design team investigate alternative concepts to the usual cast-in-place or precast concrete lining system for the Project?s many smaller diameter Deaeration Vent Shafts. The resulting design investigation produced not only an alternative lining system, but lead to a proposed non-conventional approach to shaft installation means and methods through soil and rock necessary to construct the permanent shaft lining system. This paper will outline and summarize the technical issues, contractual restrictions, and cost considerations that eventually lead to the final shaft design

By Miklós Kovács

A new type of the cast in situ piles is introduced. The installation of the new pile is based on a pushing in/gaining back procedure. A temporarily closed tip element with square shaped cross-section being attached to an upper circular shaft tube is vibrated into the soil. The steel armature is embedded. Concrete is poured into the tube and, the whole structure is gained back while the tip is in opened position. The width of the tip is less than or equal to 40 cm. The maximum length of the pile is about of 14 m. Great bearing capacity is resulted from the double soil compaction effect. No spoil is generated and, the pile construction can be controlled. The paper presents the results of four loading test at three sites with some soil data.

Jan 1, 2002

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond's original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond's original, suggests that Thoreau's advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By D. B. Buddecke

Powell Bend Mine, located in Bastrop County, Texas, is owned by the Lower Colorado River Authority (LCRA). The mine is operated under contract by the Powell Bend Mining Company (PBHC), an affiliate of Pittsburg and Midway Coal Mining Co., and produces 210,000 tons of 6500 BTU/LB lignite per year for LCRA's Fayette Power Project near La Grange, Texas. PBHC operates the surface strip mine one shift per day, five days per week with a total of nine employees; six operations/maintenance and three office/supervision. The mine's productivity in 1988 averaged 100.3 tons per manshift using an l8-cubic yard dragline to uncover the lignite. Delivered cost to LCRA, F.O.B. mine, is $6.11 per ton, which includes water control and final reclamation.

Jan 1, 1990

By Jason Laumb

Regional Energy Production ?Energy is a globally traded commodity and is influenced by regional and national needs as well as international trends. We can greatly expand energy export from the region. ?Significant opportunities exist for increased coal-based energy production.

Jan 1, 2006

By E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. This is especially true in surface and underground coal and stone mining where large, noisy equipment predominate. Workers in coal preparation and stone processing plants have also been found to be subject to high sound levels that could potentially cause NIHL over prolonged periods of exposure. National Institute for Occupational Safety and Health (NIOSH) researchers have been conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by river dredging. Little is known about the noise environment and worker exposures in these environments, where processing and mining equipment similar to coal and stone are employed. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to identify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges, in several surface mine sand and gravel operations and in the processing facilities. The locations where workers are likely to be overexposed and were found to be most susceptible to noise overexposures are reported. Results indicate that there are areas on the dredges (crane, suction pumps, and diesel engines) where sound levels greater than 90 dB(A) are present. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration (MSHA) Permissible Exposure Level (PEL) of 90 dB(A) TWA8, laborers, mechanics, oilers, helpers, pickers, and greasers are the workers likely to be exposed to hazardous sound levels and thus develop NIHL over time. Knowledge of the equipment noise, area sound levels, and worker dose levels is information that management and employees can use to reduce exposures. Exposures can be reduced in certain areas through administrative controls and through engineering controls applied to the noisiest equipment.

Jan 1, 2008