Search Documents

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By Walter Koellner

Today?s large electric mining shovels are significant users of power and represent peak loads of more than 3.5 MW to a mine?s distribution system. The power swings during normal operation can influence the line voltage at the Point of Common Coupling (PCC). The static converters for the shovel?s motions also create voltage and current harmonics which are fed back into the mine?s power grid. In addition, shovels themselves are affected by the power quality of the mine?s distribution system. This paper introduces the use of active IGBT rectifiers, also called Active Front Ends (AFE), as alternative to conventional, line commutated SCR thyristor rectifiers. The AFEs convert the AC line input into a controlled DC-link voltage. This DC voltage is then used as input to IGBT inverters, which power the AC motors of the shovel?s Hoist, Propel, Crowd, and Swing motions. The introduction of AFEs creates the following operational improvements: i) reduction of the Harmonic Current Distortion THDi from more than 40% to less than 4%; ii) full regenerative operation; iii) the potential for line voltage stabilization at the PCC; iv) high tolerance for line voltage fluctuations; v) improved dynamic performance, and, as result vi) higher availability and productivity of the shovel.

May 1, 2001

By Md Sazzadur Rahman

Electrochemical Impedance Spectroscopy studies were conducted on two organic thermal energy storage materials; Neopentylglycol (NPG) and 2-Amino-2-Methyl-1,3-Propanediol (AMPL). The ionic conductivities and dielectric relaxation times in the low temperature ordered a-phase (monoclinic for both NPG and AMPL) as well as high temperature orientationally disordered cubic y-phase are reported.

Jan 1, 2006

By S. A. Matthews, M. L. Nave

AC variable frequency motor drives are emerging technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of drive, motor, and conveyor features. The purpose of this paper is to familiarize and inform possible mining users of AC variable frequency drive attributes.

Jan 1, 1998

The National Mine Health and Safety Academy near Beckley, W. Va., is dedicated to reducing accidents and improving health conditions in the mining industry through education and training. Though this basic mission remains unchanged, the Academy now serves a much broader mining community than it did when established in the late 1960s. From its original emphasis on training federal coal, metal, and nonmetal mine safety inspectors, the Academy has expanded its programs to reach mining industry and labor representatives, state agency employees, and university students taking mining-related courses. The Academy's resident programs, short courses, seminars, and continuing education courses cover a wide range of subjects and various experience levels, but all have been developed with one idea in mind - to reduce accidents and health hazards through education and training of the widest possible audience.

Jan 11, 1979

By Cayo Soto

Mining activity is important for the development of humanity. This development must be understood from the Academy where it allows showing alternatives for the industry performance. Likewise, these mining companies need to improve their results. Historically, a few years ago the application of the ESG (Environmental, Social and Governance) criterion was verified, which is positioned as a factor/regulator in the design of the performance of industries in general. ESG as an integral part of the concept of sustainability serves as a tool to conceive mining without conflicts and with a reputation based on trust in the interrelation of the university, industry and society. Therefore, the academy must strive for new knowledge in a way that allows it to continue in the virtuous circle of constantly feeding it. In this context, the best mining practices are implemented in constant questioning of their activities. The scientific essence of the industry supported by the academy developed in an operational dynamic is addressed. Finally, the objective of this research work is to interrelate 3 variables: ESG, Academia, and the Mining Industry, where the transition of knowledge and the role of each variable in relation to each one can be understood. This allows for an additional understanding of mining in the future with new mental attention.

Feb 1, 2025

Coal exports are forecast to grow strongly, so that coal is likely to remain very important to Australia for the foreseeable future. However there is no sign that prices or profitability will rise of their own accord. Therefore the intense squeeze on costs will continue for the foreseeable future. This will mean lower manning, more outsourcing and probably an increasing rate of company attrition. As well, the political pressure from the greenhouse debate is only going to intensify and the pressure on the Federal Government after Kyoto is likely to be irresistible.

Jan 1, 1998

By D Eschebach, D Mathewson

A belt press filter (BPF) handbook containing practical information for the reference of plant designers and operators has been created as part of Australian Coal Association Research Program project C23040. The handbook combines research and experience with newer generations of equipment and circuitry. BPFs are increasingly finding application in the dewatering of thickener underflow tailings slurries due to changing environmental regulations, difficulty obtaining tailings storage facility approvals and limited water availability. Sources of BPF inefficiency and low availability stem from a lack of understanding of the key operational parameters that affect their performance. This lack of understanding typically leads to increased operational expenditure due to suboptimal reagent dose rates and increased maintenance costs, or decreases in plant availability due to excessively high filter product water contents and equipment failure. It is essential for the continued economically competitive operation of Australian coal handling and preparation plants that complex factors affecting BPF operational performance are clearly defined and understood. Installation and operation handbooks are often provided to sites with new installations, but these manuals are manufacturer- or even model-specific and are often focused on mechanical maintenance. The handbook identifies industry ‘best practice’ and improvements developed by other sites, such as extra spray bars, air system bleed valves, guarding designs, feed and filtrate protection screens and roller tensioning systems. Equations to predict optimum operating conditions – such as free moisture, belt tension and reagent dose rates, with simple feed-specific variable inputs – have been developed from site-specific test work. The correlations developed provide a benchmark for plants to attempt to achieve. This provides operators and process engineers with a tool to explain BPFs and assist them in optimising the performance of BPF dewatering plants of both contemporary and less modern design.CITATION:Mathewson, D and Eschebach, D, 2015. ACARP belt press filter design, operation and maintenance handbook, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 73–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Folwell, G Phillips, F Gassner

Geomembranes selected for various applications often start with considering target properties developed by industry organisations such as Geosynthetic Research Institute (GRI), and test methods developed by ASTM and other Standards organisations The geomembrane types are typically, initially selected based on manufacturers recommendations and chemical resistance data from the manufacturer or industry knowledge. Geomembranes considered for this project included materials with material properties that exceeded the minimum target values of various test methods. The difficulty is in selecting which parameters are most important for a particular application and also what service life can be expected for the geomembrane under various chemical and environmental exposure conditions. Accelerated aging testing of candidate geomembranes in simulated exposure conditions can be useful to select the preferred geomembrane and predict the service life of the geomembrane under different exposure conditions. The exposure conditions of immersion in acidic tailings liquor, splash zone and freeboard zone were considered for evaporation ponds on a site with significant heat and UV radiation. Candidate geomembranes considered a range of different types of polyethylene liners. The results of the accelerated aging testing have allowed the selection of the geomembrane for the range of exposure conditions and evaluation of the expected service life of the geomembrane.

Jul 1, 2021

By Revy T

A testwork program aimed to improve the assaying of underground face samples established that for an Accelerated Cyanidation Extraction using the LeachWELLTM 60X catalyst, followed by an Aqua Regia finish (to quantify non-cyanide-extractable gold): ò Assay results (including the aqua regia finish) from a full set of samples from one underground face can be returned within four hours. ò The reagent dose to make the method simple and 'bullet-proof' is 8 gm LeachWELLTM 60X and 20 gm NaCN per 200 gm sample (30 per cent solids). Pulverising is to 90 per cent passing 75 micron (compared to the standard of 90 per cent passing 150 micron), and cyanidation is completed within one hour - however both might be further optimised. ò The LeachWELLTM/Aqua Regia results demonstrate that Fire Assays suffer from a significant nugget effect which makes the Fire Assay data relatively unreliable. ò Original costs, specific to Bannockburn (viz including an Aqua Regia finish), handling approximately 20 000 to 25 000 per annum is estimated to be $5.40, ie about one-third less than fire assaying. Optimising is further reducing these costs. It is estimated that the LeachWELLT"'/Aqua Regia assay procedure has reduced the probable error limits of any given assay of this ore from the range 0.74x to 1.36x for Fire Assay, to an appreciably smaller range of 0.90x to 1.11x. Thus for a cut-off grade of 1.60 g Au/t, samples with Fire Assays ranging up to 2.18 g Au/t have 25 per cent chance of being below cut-off, while samples with Fire Assays as low as 1.18 g Au/t have an equal chance of actually exceeding cut-off grade. This 1 g Au/t range in uncertainty is generally unacceptable for many practicalgrade/tonnage relationships. By contrast, using LeachWELLTM + Aqua Regia assays, the estimated corresponding limits are 1.44 g Au/t and 1.78 g Auk respectively - a far more tolerable 0.34 g Au/t range of uncertainty. Subsequent data has demonstrated that sufficient accuracy for grade control is achieved by Accelerated Cyanidation alone, further halving the cost of assays.

Jan 1, 1994

By B Miles, D J. Williams, J Ahn, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. It is therefore important to understand the mechanisms and degree of degradation likely to occur within coal mine spoil of different qualities.To investigate this, five clay mineral-rich coal mine spoil samples were collected from the Bowen Basin, and each sample was subjected to wetting and drying cycles to simulate degradation that could be expected on wetting-up in situ, with their particle size distribution analysed both before and after degradation. These results were compared with the results of a modified slake durability test, in which the entire sample was tested.The paper presents the results of the accelerated degradation and modified slake durability tests on each of the five spoil samples. These results were related to the physical and geochemical characteristics of the samples, which highlighted their importance. The modified slake durability test may be used to rapidly simulate the expected in situ degradation of coal mine spoil on wetting-up, enabling susceptible spoil materials to readily be identified.CITATION:Vangsness, T A, Williams, D J, Ahn, J and Miles, B, 2018. Accelerated degradation and modified slake durability testing of clay mineral-rich coal mine spoil, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 83–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Xiaobing Yang, Abhishek Lahiri, Animesh Jha

"In the FFC-Cambridge process, the cathodic dissociation of oxide and CO/CO2 production on carbon anode is the basis for metal production in a CaCl2 bath. By using an inert intermetallic anode, the CO2 evolution can be eliminated altogether with acceleration in the electro-reduction kinetics. At present the process suffers from slow reduction kinetics of TiO2 to Ti metal, which can be enhanced significantly by the incorporation of alkali species in the TiO2 pellet at the cathode and in the CaCl2 bath in the presence of an intermetallic inert anode. Nearly full metallization with greater than 99% of Ti metal containing 1500 ppm of oxygen is possible to achieve in less than 16 hours of electro-reduction. Analyses of phase composition and the microstructures morphology in fully metallized pellets revealed the presence of localized solidified Ti layer, indicating that fast reduction process also involved formation of liquid phase as middle stage reaction. In addition, in situ creation of porosity and maintain higher current level during electrolysis process were two key factors to fully reduction of TiO2.IntroductionDuring cathodic dissociation of TiO2 in a CaCl2 bath and anodic evolution of CO2 on a carbon anode, which is the basis for the FFC Cambridge process [1], the rate of metallization slows down due to the formation of CaTiO3 at the reaction interface. Calcium and alkaline earth perovskites are known for their poor electrical conductivity which adversely affects the overall electro-reduction. One of the ways to increase the porosity is via the addition of polyethylene precursors in the pellet or by directly starting from perovskite [2, 3]. The experimental evidences shown in the literature confirm although the speed of reaction increases, but a complete or near complete metallization is not possible by enhancing the in-situ porosity alone, as the insulating perovskite is very slow to decompose under the equilibrium that prevails in the cell. Plethoric evidences on carbon anode show with the current decrease gradually, and finally stabilize at a very low value between 0.2 and 0.4 A, which is a testimony of the presence of perovskite insulating barrier in the current path. Our aim in this paper is to demonstrate the mechanism of enhanced electro-reduction when alkali ions are present in the oxide pellet at cathode and in the bath. We also show for the first time the use of an intermetallic anode for Ti-metal production using the FFC Cambridge process."

Jan 1, 2009

By E. T. Boshoff

Paper written on project work carried out in partial fulfilment of B. Eng. (Metallurgical Engineering) The weathering of kimberlite can be accelerated with cations in solution if swelling of the kimberlite occurs in contact with the weathering medium. The type and amount of swelling clays present, along with the surface charge and cation valence, determine the degree of swelling that can occur. Crystalline swelling occurs by the incorporation of cations in the interlayer spacing of the silica sheets. Kimberlite exposed to cupric cations showed very strong weathering, indicating that this type of weathering may be considered a viable process option. Kimberlite fines generated after weathering with monovalent cations showed poor settling behaviour compared to kimberlite weathered with di-, and trivalent cations.

Jan 1, 2005

By M. K. G. Vermaak

Kimberlite weathering has been a topic of ongoing research within De Beers for many years. Using kimberlite weathering as an alternative to crushing has many advantages e.g. power and reducing diamond breakage. Weathering could also possibly be used in conjunction with crushing just to weaken the material and reduce power consumption. These forces have driven current research to investigate whether kimberlite weathering could be utilised for these reasons. Weathering in this context does not refer to weathering over long period of time but rather to disintegration of the material in aqeous media in relative short time periods. Previous published work discussed that the presence of smectite renders kimberlite weatherable and that the amount of smectite determines the rate of weathering (Morkel and Vermaak, 2006). The current work investigates whether cation ex-change or the adsorption of organic species in the smectite interlayer could influence the observed weathering behaviour. The results show that cation exchange does take place in the presence of cation species and that the weathering behaviour can be drastically improved with especially Cu2+ cations. Concentration and time effects of the weathering was also investigated. Weathering tests with organic species such as ethanol, methanol, edta, pentanol, butanol, acetic acid and oxalic acid was performed. The results show that organic species does improve weathering but under these testing conditions was not as effective as cations.

Jan 1, 2014

By S. Hamm

Elevated total dissolved solids (TDS) content in waters downstream from surface coal mines in Central Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and ICP-MS was used to determine how leaching conditions affected release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that, for certain spoil materials, SC in leach column effluent was effectively reduced when spoil was leached first with acidic rainwater followed by ambient rainwater (vs. ambient rainwater leaching alone). This suggests that accelerated leaching might aid in long-term stabilization of some materials.

Feb 23, 2014

By S. A. Smith-Hamm, E. A. Sarver, A. S. Cox

Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and inductively coupled plasma-mass spectroscopy (ICP-MS) was used to determine how leaching conditions affected the release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that for certain spoil materials, the SC in the leach column effluent was effectively reduced when the spoil was first leached with acidic rainwater followed by ambient rainwater, as opposed to leaching with ambient rainwater alone. This suggests that accelerated leaching might aid in the long-term stabilization of some materials.

Jan 1, 2015

By J. L. Bray

ACCELERATED programs, as discussed in this paper, refer to the year-around operation of a college or university with three sixteen-week or four twelve-week terms per year, with pauses between sufficient only to allow the administrative group to perform their functions. In most engineering schools, under such conditions, the conventional four-year course can be condensed to two years and eight months. These accelerated programs of study, which now exist in most of our technical institutions, were forced upon us under the influence of the outburst of wartime patriotism, perhaps one might go so far as to call it hysteria. Many of us felt and hoped that these programs were temporary expedients, but the cold hard threat of permanency now rears its head; consequently we should examine the merits and shortcomings of the new order, and evaluate its effect on our educational system, since it may persist in some form in the postwar years, because of the changing political and financial situation. Many engineering students are being educated in state supported institutions

Jan 1, 1944

By Nathan Bowersox, Zuzana Skovajsova, David M. Jurich, Brian Harris

When unwatered after more than 50 years of operation, the White Rock Tunnel of the Upper American River Project in the foothills of the Sierra Mountains exhibited failing rockbolts and ground falls. Repairs designed for the 5 mile-long, 24-foot horseshoe unlined hydropower tunnel included pattern rock bolts, shotcrete, and cleanout of the rock trap. The work, originally scheduled for two 3-month winter outages, was completed under challenging conditions in a single 4-month outage following a carefully sequenced work plan using robotic shotcrete and rockbolter machines. Flexibility, creative solutions, and collaboration by all parties were key to project success.

Jun 13, 2021

By W. G. McBride

THE present demand for men with engineering training exceeds anything in the history of the profession. Recent estimates indicate that mechanization of war has reached such a stage that at least twelve horsepower is required now for every one horsepower needed to run the machines of the first Great War. The scale of operations exceeds anything in the past, while more territory and people are involved than ever before. Many of our allies have inadequate or no facilities for producing the thousand and one articles absolutely necessary to the conduct of modern warfare. Lack of preparedness has made it necessary to produce at an unparalleled rate to gain parity with the enemy, while our losses have been so heavy that replacement, in itself, presents a task which might well stagger less courageous peoples. This means that not only is there an unprecedented demand for engineers to produce the machines, munitions, and supplies of war, but there is a correspondingly large need for men with engineering skill in the uniformed forces to operate and maintain the vast numbers of ships, 'planes, tanks, trucks, radios, and a myriad of other devices to carry on the varied activities of war. This abnormal demand came upon us after almost ten years of stagnation in the engineering industries. During this time many trained engineers drifted into other callings, while the lack of jobs for graduates caused a falling off in the number of men training for this profession. Consequently, the supply of well trained engineers was below normal when the madman of Germany precipitated us into the present turmoil. Added to all this, we in Canada are still suffering from governmental inefficiency in the utilization of the available supply of engineers. In the armed forces, engineers have been assigned to office and other work where their engineering training is not only wasted but for which men with more suitable training could be found. Mining engineers are debarred from service as aeronautical engineers, and students in mining engineering are denied the bursaries provided for aiding students in engineering. Mining and metallurgical engineers are both barred from the Ordnance department of the army. This arises from a misunderstanding in relation to engineering training. In Canadian engineering schools, all engineers are given a sound training in the branches of human knowledge which are fundamental to engineering: mathematics, physics, and chemistry. The basic difference between the several categories of engineers lies in the fact that training in the application of this fundamental knowledge to the solution of engineering problems is given in different subjects.

Jan 1, 1942

By W. H. Langer

Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

Jan 1, 2009