Search Documents

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By Roger M. Zimmerman

The G-Tunnel heated block experiment is being conducted on the Nevada Test Site (NTS) as part of the Nevada Nuclear Waste Storage Investigations project (NNWSI). The purpose of the ambient temperature testing ph se is to evaluate rock-mass mechanical properties of a block (- 8 m3) under biaxial stress changes up to 7.5 MPa above an initialization in situ value of 3.1 MPa. Results indicate that the modulus of deformation ranges from 9.7 to 17.0 GPa and Poisson's ratio ranges from 0.21 to 0.33. In general, the higher values of the modulus and Poisson' s ratio were influenced by fracture propagations parallel to the compressive stress field. Other measurements indicated that cross-hole compression (p) wave velocities and single fracture permeability values were relatively insensitive to stress changes above the in situ value.

Jan 1, 1984

Acid mine drainage containing heavy metal ions is a large environmental problem facing the mining and mineral processing industry. The femte coprecipitation is a novel technique for removing heavy metal ions from waste water, recently applied to acid mine drainage. The fenite precipitation is usually performed at high temperature and therefore if applied in conventional manner, it becomes uneconomical to treat large quantities of acid mine drainage. In this paper the ferrite precipitation at ambient temperature-is &died. The possible mechanism of ferrite formation is discussed Experimental results from Noranda Tailing and Berkeley Pit water treated by this process are presented.

Jan 1, 1994

By John Zeni

In Australia during the 1990s, Zeni Drilling took on several demanding shaft boring contracts. This paper describes the safety, operational, technical and environmental advantages derived through the implementation of mechanized boring methods for two of these projects. The paper first describes a 3-meter (10 ft) diameter access shaft blind bored from an underground location to 440 meters (1,444 ft) deep for a gold mine in Tasmania. The construction of a 5.8-meter (19 ft) diameter, 515-meter (1,690 ft)deep ventilation shaft for a longwall coal mine in New South Wales is also described.

Jan 1, 2001

By John Fritz

THE John Fritz Medal was presented to Ambrose Swasey of Cleveland, Ohio, in the Auditorium of the Engineering Societies Building, in New York, on April 23. Charles F. Rand, Chairman of the Board of Award, presided and, after speaking very briefly of Mr. Swasey, whose friend he has been for a great many years, ,introduced Gen. William Crozier, formerly Chief of Ordnance, U. S. Army, who spoke most entertainingly of, Mr. Swasey's accomplishments in designing and manufacturing instruments of precision, particularly for the use of artillery in range finding: Dr. William Wallace Campbell, Director of the Lick Observatory, and President of the University of California, described Mr. Swasey's, contribution to astronomical advancement by his notable development of the largest telescopes in this country.

Jan 1, 1924

Said Plutarch a long time ago, ?To appreciate a man's work at the full, it is well to know the man himself, his circumstances and the incidents of his career." He might as truly have said "gift" instead of "work." Ambrose Swasey, engineer, collaborater with scientists, promoter of engineering research, patron of Engineering Foundation, advancer of the good of mankind, modest gentleman and generous giver, is, happily, well known to a great many engineers, who will therefore more fully appreciate his recent additional gift, for the use of the Engineering Foundation, which; purpose is "the furtherance of research in science and engineering, and the advancement of the profession of engineering and the good of mankind." But full appreciation of a gift of money necessitates more than acquaintance with -the giver and knowledge of the amount. Its timeliness; its inspiration; the character and continuity of its benefits, all must be comprehended. But whose imagination, though far-visioned as the great telescopes Mr. Swasey has built, can see the limits of benefit of such gifts as he has made to the Engineering Foundation, attracting-as they will-other gifts and evidences of, devotion to a great cause-? Every such gift lays responsibilities upon the recipients. Will American engineers grasp not merely, their pecuniary value but also emulate the spirit of fraternity and desire for harmony which have accompanied them? Shall we not work together and with Ambrose Swasey to advance still further the good of mankind, thus to demonstrate an acceptance of our obligations to humanity which is a counterpart in a democracy of the noblesse oblige of aristocratic tradition?

Jan 12, 1918

By B Hayes

The Ambuklao and Binga Rehabilitation Project is a 175 MW hydro power project currently under construction across dual sites in the north region of Luzon Island, Philippines. When it was built in 1956, the Ambuklao Dam harnessed the second largest hydro-electric reservoir in Asia. However, due to landslide erosion and prolonged silt infiltration caused by an earthquake in 1990, the power plant has been rendered inoperable since 1999.To bring the power generating facility back to life, the project scope entails the rehabilitation and construction of civil structures, shafts and tunnels. A major component of these works is the decommissioning of a section of the seven metre diameter headrace tunnel by installing a concrete plug. The headrace tunnel is part of a closed waterway system that connects the dam via a shaft, exhibiting a hydrostatic pressure of 13 bar (1300 kPa) at the location of the new tunnel plug. In addition, the power station ball valves have seized ajar and the damaged intake riser is unsafe toaccess thereby requiring the plugging operation to be carried out under live flowing conditions.Working under hydrostatic pressure and live conditions, the headrace plug will be an underwater tremie pour operation that includes drilling and concrete injection through blow out preventer caissons installed in the floor of an underground chamber above the tunnel. The purpose of this paper is to describe the key engineering and planning components involved in this operation including pre- and post-grouting, chamber crane, sonar, local water compensation, jet flushing, drilling, caisson installation, and concrete design, production, delivery and placement. The success of this task rests on the strategic preparation and operational management of risk and safety in a challenging rural environment.

Mar 8, 2011

By Tim Neil, O&apos

The coming years should see moderate growth in the US coal industry. That growth may come at the expense of the oil and natural gas industries. Conoco pegs coal growth at 2% a year, until the year 2000. During that same period, Conoco projects only 0.5% annual oil growth and "a flat or negative trendline" for natural gas. This is compounded by the fact that coal has a delivered cost per Btu that is only half as much as it is for natural gas and only a third as much as it is for oil. So said Ralph Bailey to many of the 2600 attending the opening session of the American Mining Congress Coal Convention, May 12-15, in Pittsburgh, PA. Bailey is chairman of the AMC. He is also chairman of Conoco. While coal's projected growth is not spectacular, "it is in fact almost an assured growth," Bailey said. Weak oil and gas prices will likely prevent faster growth for US coal. Most of coal's increased demand will come from the electric utility industry and expanded steam coal exports. Conoco's study projects that domestic coal demand will be strengthened in the 1990s. By then, the present surge of nuclear power plant constuction will be over. And there will be a lack of acceptably priced, large-scale generation alternatives for utilities. "It is not likely that any electric utility is going to be ordering new nuclear reactors," Bailey said. "And as oil and gas supplies become scarcer and more costly, it is only logical that coal is going to fill the gap." At the same time, Bailey believes the US coal industry must find ways to lower its costs. He said cost excesses can be found in "regulatory overkill, labor, and simply bad habits" hidden by years of high inflation. "Those costs have now been laid bare, because we are going through a pe¬riod of disinflation. We have to put our house in order, particularly if we are going to compete in world markets." Bailey also touched on coal research. "The industry certainly accepts the fact that we must find a way to burn coal as cleanly as possible. A lot of work in that regard is going on. I expect there will be some significant break-throughs." Bailey said the coal industry is being squeezed this year. Last year, coal customers accumulated inventories in anticipation of a major coal strike that never materialized. Now, many utility customers are working down these inventories. So they are not taking deliveries on their coal contracts. But coal use is up in 1985, compared with 1984, Bailey said. So increased coal use, along with supply drawdown, should strengthen the coal market before the year is out, he said. After Bailey's presentation, some 100 speakers addressed policy and technical topics at 15 sessions during the four-day meeting. It was the first time since 1977 that the AMC Coal Convention has been held in Pittsburgh. And this year's attendance was up 40% from the last AMC Coal Convention held two years ago in St. Louis, MO. This year's registrants included 228 companies, 225 manufacturers, and 106 associated members. The only negative was the David Lawrence Convention Center. It was less than ideal. By turns, meeting rooms were too small, too cramped, or too far from one another. The session on longwall mining was so crowded that the doors were propped open so conference delegates could peer in. A concurrent manufacturers' forum session needed 50 more chairs to accommodate those wanting to attend. However, on to summaries of some of the presentations. Coal transportation and export Since Congress approved the 1980 Staggers Rail Act, railroad rates for hauling coal have not been excessive. In fact, rail rates for coal have increased less than 0.5% a year, in real terms, since 1980. Moreover, the market oriented principles written into Staggers are contributing to the improved financial and operational health of the nation's railroads. But no railroad is earning excessive profits. That is the gist of a coal transportation study being completed by the US Department of Energy. William Vaughan is DOE's assistant secretary for fossil energy. He affirmed the thrust of the upcoming report. Vaughan did allow that Interstate Commerce Commission (ICC) regulations on rate reasonableness could permit the railroads to exploit their monopoly power on captive shippers. Luncheon comments later made by Don Hodel confirmed Vaughan's comments on railroad rate justification. Hodel is Secretary of the

Jan 7, 1985

In the mile-high city of Denver. Colo., the mining industry's political adjunct, The American Mining Congress, held its annual meeting, September 27-30. The Honorable Maurice H. Stans, in what became the keynote address of the meeting, spoke of a "common interest in a basic reality of 1970, a reality involving ecology, energy, raw materials and natural resources.”

Jan 1, 1970

Schedule of Events

Jan 8, 1950

Though the mining industry is beset with problems-a broad slump in metal prices, a rash of acquisitions and takeover attempts, rising capital costs, and an aggressive Canadian energy program-there was an under-current of optimism at the 1981 AMC conference that's been missing at industry meetings in recent years. The industry anticipates a turnaround in the 1980s, buoyed perhaps by the new spirit of cooperation from the Reagan administration. For the first time in years, it appears that Washington and the mining industry share mutual goals for developing the nation's resources. A number of prominent Reagan officials were on hand during the three-day conference in Denver, September 28-30, to reassure conferees that restrictions plaguing energy and minerals development would be eased. Interior Secretary James Watt and other government speakers promised cooperation in bringing balance to federal public lands policies, a review of regulations that have hampered the industry, and prompt action on domestic minerals policy. Daniel N. Miller, Jr., assistant interior secretary for energy and minerals, said, "It is our intent to dismantle the overhearing bureaucracy that has stifled mineral and energy exploration. We know that Interior's rules have shackled the mining industry in recent years, and we know that those rules must be eased." Miller noted that the administration will not permit mining on national park lands or wildlife refuges, but added that "we must assess a variety of uses of public lands ... we will restore lands to multiple use where practical." EPA administrator Anne Gorsuch assured industry representatives that the administration intends to work within environmental laws and with Congress to review and revise water, soil, and air pollution policies. "We have a strong commitment to see that there are major mid-course corrections" of air regulations, Gorsuch said. Support from these "new friends in Washington" will be crucial in light of the serious problems pressuring the industry. Copper prices have plunged to almost three-year lows and prices for molybdenum, gold, and silver have slumped. Earnings are down and today's high interest rates prevent a quick turnaround. Companies are on edge after the recent takeovers of Kennecott, St. Joe Minerals, and Texasgulf Though the companies may benefit from the major injection of capital that large energy firms can provide, many observers fear the new parent companies won't be willing or able to survive the cyclical metal markets. Arco and Gulf Resources, for example, have been criticized for closing Anaconda's Montana copper facility and the Bunker Hill unit in Idaho, respectively. Canada's national energy program has brought additional pressure on the industry. This policy, which emphasizes Canadian majority ownership of the country's energy sources, resulted in acquisition of Texasgulf's Kidd Creek lead-zinc-silver complex by Canadian and French interests. In response, the American Mining Congress adopted two resolutions on takeovers. One calls for the US government to review laws regulating tender offers and takeovers "to better ensure that principles of fairness and sound investment policy govern such transactions.'' The other asks the government to demand "fairness and reciprocity" as a basis for US policy governing international trade in minerals and investment relations with other countries. AMC's shopping list included four other priority goals, aimed primarily at the Interior Department: • Prompt implementation of Interior's efforts to bring order and balance to rules governing access to public lands for exploration and development. • Statement by the President of a comprehensive and coherent domestic minerals policy. • Amendment of the Clean Air Act to remove impediments to productivity and barriers to economic development that are not necessary to essential goals of the act. • Development of new approaches to better achieve worker health and safety in the most cost-effective manner without penalizing productivity. Almost 6000 mining industry executives attended the 1981 convention-the largest in AMC's 84-year history. As in years past, the conference offered a wide spectrum of presentations-nearly 100 papers in 26 sessions-ranging from commodity forecasts to the latest technical achievements. New Administration Stockpile Goals The minerals availability session included a presentation on management of the minerals stockpile by Paul K. Kruege r of the Federal Emergency Management Agency. Krueger notes that rather than providing incentives for development of a domestic raw materials industry, the government has "a history of providing disincentives to industry." In mining industries, he adds, the rate of productivity growth has been -6% over the last six or seven years. Krueger feels there will be a major change under the Reagan administration. In March 1981, FEMA began the first purchase program for the national defense stockpile in over 20 years. The stockpile is sadly out of balance, Krueger adds. Stockpile materials are

Jan 12, 1981

“The mining industry can do more to alleviate world poverty, hunger and human misery, more to close the widening gap between advanced and developing nations and more to achieve international peace and understanding than any other single force in the world," Charles W. Court, Minister for Industrial Development, Western Australia, told the American Mining Congress audience at the opening session of the 1969 Mining Convention, October 19-22, San Francisco. Australia, he pointed out, is a shining example. In 1971, 60% of U.S. mining investment overseas will go to Australia and other parts of Oceania, an increase of 42% over a year ago. Australia has capitalized on world needs, its own rich resources and good investment climate. Developing nations can and should do the same, but they mix emotion with nationalism, often frightening away foreign investment which could breathe life into dormant and backward areas, said Court.

Jan 12, 1969

Seattle offered sunny, dry weather to about 2500 mining men who assembled September 10 to 14 for the 1961 American Mining Congress. The impact of snappy sessions on national mineral policy, state of the industry and foreign competition (to name only a few) was somewhat overshadowed by enthusiasm of conventioners for salmon fishing. This lordly fish, which mysteriously runs to its hatching place to spawn and die at this time of year, was not cooperating with the anglers in Puget Sound. However, this did not prevent consuming ample amounts of the deliciously prepared Quinault salmon at the "Potlatch" celebration.

Jan 10, 1961

Two sessions during the recent AMC Mining Convention in Los Angeles, September 23-26, served to update industry personnel on the status of health and safety regulations in the US. As reflected by the American Mining Congress resolution on mine safety and health, "Based on experience with the federal Coal Mine Health and Safety Act of 1969 and the federal Mine Safety and Health Act of 1977, (AMC) does not believe that laws designed to force compliance with regulations through the imposition of criminal or civil penalties will result in safer mines. (AMC) feels that the government's participation will be much more productive if greater emphasis is placed on research, training, and inspections aimed primarily at assisting operators and employees in recognizing and eliminating hazardous conditions and practices.

Jan 11, 1979

By Mark G. Colwell, Russell Frith

"An Analytical Model for Coal Mine Roof Reinforcement (AMCMRR) has been developed. AMCMRR utilizes a Factor of Safety (FOS) approach, which is commonly used in all forms of engineering. The starting point in the development of AMCMRR was an existing analytical roof behavior and roof support design methodology/model, originally developed by Colwell. This technique was used successfully in the Australian underground coal industry for roof support evaluation and design prior to and during the course of the research project, and when used, it was essentially calibrated on a site by site basis.It has long been recognized that bolts and longer tendons can modify the behavior and load bearing capacity of the reinforced roof via the concept of beam building. The break-through in developing AMCMRR was combining the original analytical model with a comprehensive database (associated with Australian collieries) to effectively quantify this reinforcing effect, and this in turn provided the ""platform"" by which this analytical model can be calibrated for the entire Australian underground coal industry.This paper focuses on the application and use of AMCMRR and the analyses undertaken to quantify the reinforcement beam building offers to the immediate roof. Furthermore, this paper demonstrates that a combined empirical and analytical approach is currently the most practical way of developing credible geotechnical design tools for the Australian or any other underground coal industry.BACKGROUNDBy the start of 2006 the ALTS (Analysis of Longwall Tailgate Serviceability-Colwell et al., 2003) and ADRS (Analysis and Design of Rib Support-Colwell, 2006) design methodologies were being routinely and widely used within the Australian underground coal industry. As a result of their success, Colwell Geotechnical Services commenced a research project entitled, ""The Future Development and Integration of ALTS & ADRS for Improved Underground Roadway Design. "" The project (which became known as the ALTS 2006 Project) was funded directly by several of the major coal producers as well as individual Australian collieries."

Jan 1, 2010

By Jorge Alberto Soares Tenório, Flávia Paulucci Cianga Silvas, Bianca Medeiros, Denise Crocce Romano Espinosa, Ivo André Homrich Schneider, Daniella Cardoso Buzzi, José Roberto de Oliveira

"AMD is one of the main problems associated with mining activities and the techniques used in their treatment may be the biosorption. The aim of this work was to study the rice husk as a biosorbent for the AMD treatment keeping constant: pH (2.6), biomass concentration (1g.L-1), temperature (25°C) and agitation (175rpm). And varying the contact time of 5, 20, 60 and 240 minutes. Rice husk samples will be characterized before and after the biosorptives tests through analysis of SEM and IR. The micrographs indicate the occurrence of micro-precipitation and changes in biomass physical structure. Since the infrared spectra indicate changes in functional groups present in the biomass before and after the biosorptives tests. AMD synthetic solutions will be analyzed by ICP in order to quantify the metals concentration captured by biomassIntroductionThe preoccupation for the environment has led the industry in general, to treat their waste. As the only industrial activity is increasing, the pollutants generated must undergo treatment processes aimed at reducing pollution, and therefore, less aggression ecosystems.In mining there is waste water with accumulation of heavy metals, and these are harmful to health of living beings, thus being one of those industries responsible for some pollution of the environment. These wastewater in contact with oxygen to generate an acidic water is called acid mine drainage (AMD). This aqueous solution has a pH below 3 and varieties of dissolved metals. When this solution comes in contact with water, generates a series of environmental problems, so there is a need to recover the metals present in the DAM."

Jan 1, 2012

By Gary Krix

The Amdel Thickener Interface Gauge (TIG) provides continuous on-line measurement of the level of the liquid/solid interface in thickeners and Counter Current Decantation (CCD) washers. Unlike other interface level measurement systems, the TIG also determines the span of the transition zone. The transition zone is the region between the clear liquid overflow zone and the compressed solids zone. The Thickener Interface Gauge determines the level of the interface by measuring the natural radioactivity of the solids in the thickener tank using an array of up to twelve detectors mounted vertically in a stainless steel probe. All solids contain low levels of natural radioactivity while the liquid phase generally does not. The concentration of natural radioactivity at each level in the thickener therefore depends on the concentration of solids. The radiation emitted by the solids is converted to electrical pulses by the detectors in the probe and the pulse-rate provides an accurate measurement of the density. A typical count-rate profile is presented in Figure 1. The vertical axis indicates the depth in the tank referenced to the surface of the liquid. The horizontal axis indicates the count-rate measured by the TIG probe, this count-rate is proportional to the density and can be used to determine the settling rate. The count-rate at the top of the graph is relatively low, this region corresponds to the clear overflow zone which contains virtually no solids. Moving down the vertical axis the count-rate increases dramatically at the level of the transition zone where the solids content increases with the depth in the tank. In this region the settling conditions of the solid particles change from free settling to compression. Moving further down the vertical axis the count-rate reaches a plateau where the count-rate remains relatively constant although there are often small fluctuations, this region corresponds to the solids compression zone. The liquid/solid interface as measured by the TIG corresponds to the depth at which the count-rate crosses the target count-rate which is generally selected to be midway between the liquid count-rate and the compressed solids count-rate. The length of the TIG probe is selected to cover the typical operating range of the liquid/solid interface in the thickener or washer. If, for example, the minimum bed level is 3.0 metres below the surface of the liquid then the probe length is selected to extend 30 metres below the surface. The TIG probe can include up to twelve detectors and the se are spaced over the measurement range. For small measurement ranges of around one metre 4 to 6 detectors would normally be used while for larger measurement ranges of three metres or more twelve detectors would be supplied.

Jan 1, 1993

By Carl P. Maronde, William P. Barnett, Patricia A. Rawls

The commercial deployment of advanced fine-coal cleaning technologies depends on cost-effective approaches for efficient separation and ancillary operations in handling, dewatering, drying, and transporting coal fines. As a result of two solicitations under the High-Efficiency Preparation component of the Department of Energy Coal Preparation Program, several projects were initiated for testing and evaluation of emerging technologies and equipment that address operational difficulties associated with coal fines. This paper will update the status of those projects and discuss how the technologies they represent can ameliorate some problems associated with coal fines in today's preparation plants.

Jan 1, 1995

By Olga K. Karakasi, Angeliki Moutsatsou, Ioanna Kavallari

"The present study focuses on the amelioration of the behaviour of high calcium fly ash (HCFA), investigating its application in a new environmental field: oil spill clean up. High calcium fly ash is a by-product of electric power plants, produced annually in large quantities, whose greater amount is landfilled. Some of its properties, such as its chemical and mineralogical composition, its fine particle size, its porosity, floating ability and hydrophobic character make it an attractive material for this purpose. Researches showed that when added to an oil spill, it forms a semi-solid phase, which allows the quite total removal of the oil, but it is not stably retained on the surface. In order to ameliorate its floating ability, the decrease in its specific gravity by mixing with a lighter material is investigated. In the present study the mixing with two materials, already used in oil spill clean up, sawdust and a polymer, has been examined. Addition of 15-25% w/w sawdust to HCFA results in a material with better performance than HCFA or sawdust alone: it has a satisfactory floating ability and allows total removal of oil. Addition of the polymer, however, has resulted in no significant amelioration of the oil sorption behaviour of HCFA, probably because no affinity between HCFA and polymer has been achieved.IntroductionCoal fly ash is a by-product of coal combustion in electric power plants, produced worldwide in huge quantities, approximately 500 million tones annually. High calcium fly ash (HCFA) is classified to class C presenting a (Al2O3 + SiO2 + Fe2O3) > 50%. The production of lignite fly ash in Greece comes up to 13 million tones annually, of which only 12% is used in construction applications, the other being landfilled [5, 6].Besides its limited application worldwide as a construction material, research is focusing on the development of new environmental applications, such as waste stabilisation and solidification, soil and water environmental improvement [9, 12]. For the application of fly ash in further environmental fields several chemical modifications have been applied, in order to improve its properties. Extensive research has been focused on the conversion of both coal and lignite fly ash to zeolite and its further application in environmental field, such as the uptake of inorganic (heavy metals and ammonium [8, 11]) or even organic compounds (methylene blue [15]) from waste water streams, or the use as molecular sieves, to adsorb water molecules, SO2 and NH3 from gas streams, due to the high cation exchange capacity and porosity of the produced zeolithic material. Furthermore, lignite fly ash has been combined with sodium silicate solution, prepared by treatment of rice husk ash, and tetrapropylammonium bromide, to synthesise hydrophobic zeolite ZSM-5 [4]."

Jan 1, 2008

"Decreasing gold-in-ore grades is one of the main drivers of poorer productivity and rapidly escalating unit costs. Grinding costs, water use and reagent consumption are all intimately related to the ore grade processed. Various pre-concentration technologies have been developed that can be applied at various stages of crushing prior to ore grinding. This paper will review the amenability of ores to coarse particle barren gangue rejection for fine crush sizes in the pumpable particle size range (i.e., particles between 5 mm and 0.3 mm in size). The liberation of oxide gangue achieved during crushing is evaluated by proxy using sink-float analysis and the deportments of gold, sulfur, and arsenic into sinks and floats are monitored. Amenability of gangue rejection by continuous gravity separation is evaluated after various crushing modes (vertical shaft impact crushing, cone crushing, and HPGR crushing). The potential to identify coarse particle mineral association and liberation using three-dimensional x-ray computed tomography will be discussed.INTRODUCTIONThe aim of research in this area is to explore some of the attributes which make some ores amenable to preconcentration, or rejection of a significant component of the feed mass to tailings at a coarse liberation size. Characteristics such as ore type, mineralogy, breakage pattern, particle shape, and liberation characteristics may need to be examined to identify amenability to pre-concentration amenability.It is intended to focus on continuous gangue rejection in the pumpable size range (0.3–5.0 mm) as this remains one of the key opportunities to reduce processing costs through a combination of techniques including screening (for mineral differentiation rather than size classification only) and gravity separation (using jigs). This is to be contrasted to conventional preconcentration as performed with automatic ore sorters."

Jan 1, 2016