Search Documents

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

The imbalance between the coal resources contained in thin seams (1,5 m or less) and the production from them is outlined. It is suggested that an Increase In the exploitation of thin coal seams is necessary, and that drum-type continuous miners can produce a substantial amount of any increase. Continuous miners are employed in a number of mining methods including bord-and-pillar, pillar extraction (stooping), rib-pillar extraction, and shortwalling. These techniques of mining are evaluated with respect to production rates and the cost of extraction for South African conditions included in these evaluations are the types of equipment used to transport coal from the mining machine to the section conveyor belt. Computer simulation techniques are used to generate the required production levels, and interpretations are made of other results from the computer modelling. For thin, coal seams, bord-and-pillar mining utilizing continuous haulage is apparently the most productive and cost-effective of all the methods using the continuous miner. The relative efficiencies of the other techniques of mining and of coal-transportation vehicles are also outlined.

Jan 1, 1984

By Dr. Anthony J. Konya

The modern era has seen a boom in virtual training platforms. This study details the effectiveness & applicability of online training in comparison to in-person training for the drill & blast industry.

Feb 1, 2020

By D. Warkentin, M. Tomlinson, A. Nacu

"This study focuses on comparing the “blinding” effectiveness of various organic additives as part of a general review of using organic additives to mitigate preg-robbing and improve gold recovery during cyanide leaching of carbonaceous gold ores. The laboratory results compared the impact of various organic additives on the prevention of gold adsorption using both activated carbon and ore samples containing carbonaceous matter, generally referred to as total carbonaceous matter (TCM). Although several organic reagents were found to have a significant blinding effect on activated carbon, these results did not translate into increased gold leaching efficiencies with actual ore samples.INTRODUCTION Preg-robbing refractory ores, which contain carbonaceous matter, have been problematic in cyanide plants for many years. In industry, preg-robbing by carbonaceous matter may be mitigated using various techniques including flotation, to remove the carbonaceous matter; addition of blinding agents, to passivate the carbon surface and prevent adsorption of gold cyanide complex; roasting, to partially or fully destroy the carbonaceous matter; chemical oxidation (Abotsi & Osseo-Asare, 1986); pressure oxidation; or microbial deactivation (Dunne, Staunton, & Afewu, 2013). Carbon-in-Leach and Resin-in-Leach are also used as process alternatives in which activated carbon or resins are used to compete with the carbonaceous matter for gold cyanide adsorption. For highly preg-robbing ores, thiosulphate leaching may be considered as an alternative to conventional cyanide chemistry (Baláz, et al., 2000). Natural carbonaceous matter is composed mainly of hydrocarbons, organic acids, and graphitic/amorphous elemental carbon. Natural elemental carbon that behaves as activated carbon is considered to be the main reason for preg-robbing, although the true nature of this phenomenon is not fully understood (Tan, Feng, Lukey, & van Deventer, 2005). In general, the hydrocarbon fraction is assumed to have negligible interaction with gold, while organic acids, such as humic acids, may form complexes with gold, inhibiting its extraction in cyanide solutions. Organic reagents have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Abotsi & Osseo-Asare (1987) tested various organic compounds, with two possible effects in mind. First, the organic compounds were expected to adsorb onto the surface of the solids as anionic/cationic species; the resulting electrostatic interactions between the Au(CN)2- anion and the negatively/positively charged surface would inhibit/enhance the gold uptake. Second, the organic reagents were expected to coat the surface of the carbonaceous component in the ore, limiting the available adsorption sites and reducing gold losses. Optimal reagent dosage depends on ore mineralogy, maturity and surface area of the carbo"

Jan 1, 2019

By J. D. Miller, D. M. Catarious, F. L. Stanley

The quality of cleaned products from coal preparation plants is often variable due to natural fluctuations in the washability characteristics of the plant feed. To combat this problem, many modern plants have installed on-line analyzers that provide feedback for the real-time control of product quality via the adjustment of circuit cutpoints. Unfortunately, optimization studies show that this approach may actually lead to increased losses of saleable coal. This paper discusses the problems associated with the real-time manipulation of circuit cutpoints and suggests alternative modes of operation that are better suited for plant optimization. A case study involving an eastern U.S. coal plant has been used to compare the economic impacts of these different approaches for plantwide control.

Jan 1, 2000

The Crown Minerals Act provides a new+framework for the management of Crown owned minerals and requires that regard be had for the principles of the Treaty of Waitangi. The Act requires the preparation of Minerals Programmes to achieve the Act's objectives of efficient allocation of rights and the recovery of a fair financial return on its minerals. Efficient allocation requires that a permit is allocated to the party which values it most highly. A fair financial return to the Crown must be considered in the context of the economic rent available from individual mineral projects, with the proviso that a nil return to the Crown as the owner of the resource will not be considered a fair return from the community's perspective.

Jan 1, 1992

By C. L. Lin

Linear grade distribution measurements determined from polished sections of randomly oriented particles can be used to estimate the extent of liberation for multiphase particles of specified size. Two techniques, optical image analysis and microprobe analysis, have been used to establish linear grade distributions. Both techniques were evaluated and compared using variable grade samples of products from a copper porphyry flotation circuit. The statistical significance of the linear grade distribution data obtained by optical image analysis was assessed. The average chalcopyrite content of these samples, as determined by chemical assay was used to estimate the variance of the experimental procedure. For a given accuracy, the number of particles required to obtain an unbiased representation of the sample was determined.

Jan 1, 1985

By G. Sandoz, C. A. Siebert

OIL quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State `A'-Vapor Blanket Cooling-In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage `B'-Vapor Transport Cooling- Termination of the `A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage `C'-Liquid Cooling--The `B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the `B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage `B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 2 ½ -in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and 1-in. stream height, and (2) a ½ -in. orifice and a 3 ½ -in. stream height. In all cases the samples were suspended so that the quenched end was ½ -in. above the orifice. The steel used was an NE 9450 having the following analysis: [ ] Some tests were run on an NE 8740, 3312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been omitted' from this paper. The test bars were machined from 1 1/8 -in. stock to 1-in. diam by 4 in. long.

Jan 1, 1948

This paper describes an investigation of the sampling problems which contributed to erroneous Concentrator production forecasts at the mining operation of Bougainville Copper Ltd (BCL) in the North Solomons province of Papua/New Guinea.Reference figures provided by independently verified commercial shipment data demonstrated the existence of a bias in the calculated Concentrator production; the challenge was to identify systematic errors in each of the contributory measurements (feed tonnage and feed, tailings and concentrate grades).The uncertainty surrounding specific sampling and measurement errors precluded optimum metallurgical control and performance of the milling circuit, encouraged disputes about the difference between Mine versus Concentrator production estimates, and cast some doubt on efforts to follow political guidelines concerning a maximum feed tonnage or recovery oriented mill operating concept.An evaluation of routine results as well as specifically targeted test work identified the sampling errors associated with measured individual parameters.The emphasis in this report is on the procedure for quantitative error assessments.The measured performance of a mineral dressing plant is subject to a systematic error balance which can be derived from the more familiar weight and metal balances such as the two- or three-product formula.The resulting equations are generally valid, and they are applied to the measurements obtained at BCL's Concentrator to illustrate the method.

Jan 1, 1976

By Yoginder P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15 percent to a maximum depth of 150 feet. The pit orientations along the dip (dipline), strike (strikeline) and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas, and also to furnish a data base-for the computer simulation models. A dragline micro- simulation model (Fluor), a shovel/truck simulation model and a cost analysis model were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and angle of dip. The productivity (Cu.yds/hour) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity larger size trucks were preferable to smaller size trucks in the pit configuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip.

Jan 1, 1984

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

By Philip Schane

THE subject of steel cleanliness has always been a major one in the steel industry and much study and effort have been expended toward improving the cleanliness of steel and meeting the ever increasing demands of customers for steels that will give better performance in service and permit economies in design and efficiency of the final product. Sometimes wee may feel that-these demands are unnecessarily stringent, and probably this is true in some instances. However, the pressure for higher quality has acted as a stimulus toward improving quality and, therefore, has tended to promote progress. In this paper, the whole subject off cleanliness is covered in a general way. In the discussion' on steelmaking practices, remarks have been limited to basic electric- furnace practice in the making of alloy steels.

Jan 1, 1947

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

By Kirk Ellison, Sherif Elfass, Ramin Motamed, Kevin V. Stanton

"The determination of accurate load transfer curves are essential for estimating deep foundation loadsettlement response using t-z style analyses. While recently developed semi-empirical methods from Ashour et al. (2010) and Ashour & Helal (2012) have shown promise in preliminary studies, they have not yet been thoroughly benchmarked against a more widely accepted approach. To address this issue, these recent procedures are implemented in the computer program CGI-DFSAP to predict the results of four Osterberg-cell (O-Cell) load tests. These predictions are compared to outcomes obtained following the recommendations from Reese & O’Neill (1988) for t-z analyses of drilled shafts in sand and clay which are carried out with the program TZ-PILE. Overall, the results suggest that the new approach offers improved accuracy regarding predictions of drilled shaft response to axial loading.INTRODUCTIONThe behavior of axially loaded deep foundations is often analyzed using a technique known as the t-z method. In this method, deep foundation elements are broken into multiple segments which are supported by discrete nonlinear springs to capture the contribution of both side-friction (t-z springs) and end-bearing (Q-z springs). Hence, the t-z and Q-z relationships dictate the predicted load-settlement response. A number of different approaches have been developed to estimate load-transfer curves with some relying solely on empirical data from laboratory and field experiments (i.e. Coyle & Reese, 1966; Vijayvergiya, 1977) and others based mainly on analytical frameworks (i.e. Kraft et al., 1981; Randolph, 1994). Reese & O’Neill (1988) provide recommendations which are widely used for developing t-z and Q-z curves for analyzing drilled shafts. This method is hereafter referred to as Method 1 (M1). It should be noted that these empirically derived relationships are only applicable for problems associated with drilled shafts and are therefore not appropriate for developing load-transfer curves for other types of deep foundations (i.e. driven piles). This is because of the difference in the frictional resistance which can be developed between a circular concrete-soil interface as opposed to that of other materials (i.e. steel) and/or different cross sectional geometries.The M1 load-transfer curves form the basis for the t-z analysis of drilled shafts implemented in the computer program TZ-PILE (Ensoft, 2014). In light of this, TZ-PILE is employed herein as a reference to compare against the capabilities of another method of implementing t-z style analyses. This method is based on a semi-empirical framework for soil behavior developed by Norris (1986) and is implemented using the program CGI-DFSAP (Computers & GeoEngineering Inc., 2011). More information concerning this approach, hereafter referred to as Method 2 (M2), is given in subsequent sections."

Jan 1, 2017

By S. D. Graham

"The extractive metallurgy of gold is largely controlled by mineralogical factors such as the presence of refractory gold, particle size, gangue mineral associations, presence of preg-robbers, oxygen and cyanide consumers, and locking characteristics in base metal sulphides. Light microscopy and automated mineralogy techniques are regularly used to characterise the effect of these variables on gold recovery. However, despite their widespread application there are a range of limitations when grades are low. Typically, the analysis of low-grade samples requires the preparation and analysis of numerous polished blocks. This is often costly and time consuming, with complexities regarding analysing statistically representative particle quantities and problems overcoming stereological bias. This is compounded by the “nugget” effect and high tenor nature of gold mineralisation. X-ray Microscopy techniques have the potential to overcome many of these problems, in particular the statistical representivity of analysis, removing stereological bias and effectively locating phases that are present in ultra-trace proportions. In this paper we outline the potential benefits of employing X-ray Microscopy (XRM) in characterising gold losses from a typical Cu-Au porphyry project, which were illusive in 2D based analysis. The talk will also outline additional application areas of XRM within the extractive value chain."

Jan 1, 2017

By M Harris, C Goodall, B Knopjes

The objective of this work was to investigate the effect of milling and flotation circuit configuration on flotation performance of platinum-bearing ore from the UG2 reef of the Bushveld Igneous Complex in South Africa. Pilot plant trials were conducted at Lonmin Platinum using a highly automated pilot plant (a floatability characterisation test rig or FCTR), with a pilot ball mill, a stirred media detritor and an ISA mill. Different milling and flotation configurations were tested, without changing the overall grind size distribution or flotation residence time from one circuit to the next. Results from the pilot plant tests indicate that staged grinding, with intermediate flotation stages, can achieve significant performance benefits in comparison to a single grind-float circuit, for an equivalent overall grind and flotation residence time. These findings are explored qualitatively, in terms of the recovery and transportation of fast, slow and non-floating platinum-bearing particles through the various milling and flotation stages, and an optimum strategy for the separation of this type of ore is explored and discussed.

Jan 1, 2005

By C. Daly

The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course, ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course ? the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks. The term ?peer assessment? in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ?try and see? approach. Each student must describe in detail the process they undertook to achieve their final design ? hence the approach is independent of the discipline and/or project selected. Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ?run? is for feedback only during week six and hence no moderation is undertaken. It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students. Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks.

Jan 1, 2014

By C. Daly

"The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course,ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course - the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks.The term ‘peer assessment’ in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ‘try and see’ approach. Each student must describe in detail the process they undertook to achieve their final design - hence the approach is independent of the discipline and/or project selected.Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ‘run’ is for feedback only during week six and hence no moderation is undertaken.It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students.Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks."

Jan 1, 2014

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar, P. M. Van Den Heever

Some of the important properties of solid electrolytes that influence the performance of electrochemical oxygen probes are discussed in the first part of this paper. It is shown that accurate and reproducible measurements of oxygen in liquid steel are possible with commercial oxygen probes only if great care is exercised in the make-up of the chemical and phase composition, as well as the microstructure of the solid electrolytes used in these probes. To prove this premise, the second part of this study reports on the results of an experimental evaluation of new commercially available oxygen probe. An evaluation of the solid electrolytes used in this probe indicated that the consistency of the chemical composition, degree of stabilization, and microstructure of the electrolytes used are well controlled. The successful application of this particular oxygen probe under industrial conditions was confirmed. It was also found possible to make reliable and reproducible measurements, with acceptable uncertainty, by proper handling of the probe. Some recommendations are made as to the interpretation of the e.m.f. response curve and the use of the electronic processing unit supplied with the probe.

Jan 1, 1987