Search Documents

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 1960's, is still proceeding. The largest mechanical flotation machines avail-able today have unit volumes in the range of 38.2 to 43.9 M3 (1,350 to 1,550 cft). Designs for mechanical flotation cells of unit volumes as large as 70.8 m3 (2500 cft) are available. The development of these "giant" flotation machines has been and continues to be motivated by the increasingly critical forces of higher energy and capital costs, decreasing ore grades, and lower (real) prices for the products. As an expansion of a previous publication, this paper reports the further development of an improved mechanism for these large flotation machines. The starting point in the develop¬ment of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which s is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1983

By J. A. C. Diering

The determination of stresses and displacements close to tabular excavations is of considerable importance in the planning of tunnels and of remnant and pillar layouts. This paper gives a description of a simple yet effective method for the achievement of improved values from an analogue or MINSIM type of analysis. Essentially, closures and rides (the movement of hanging-wall relative to footwall) in mined-out areas are assumed to vary in a piecewise linear fashion as opposed to a piecewise constant fashion. As the former fashion more closely resembles the true variation, it is possible for the stresses and displacements at points close to the excavations to be calculated with much better accuracy.

Jan 1, 1980

By R. T. Stain

Dynamic methods of load testing piles using a drop hammer to generate the input force have been in use for many years. These systems are based on the wave equations developed at the Case Institute of Technology, Cleveland, Ohio in the late 1960's and are well documented. Such tests are generally restricted to preformed driven piles, the driving hammer being a convenient means of generating large input forces. In 1979 the CEBTP (France) was sponsored by the FNTP (Fédération Nationale des Travaux Publics) to undertake research into existing classical methods and to develop a test that would be equally applicable to bored cast in place piles. The result of this research programme is a methodology known as SIMBAT, and which was included in a series of class A prediction trials in Belgium in 1987 (Refs 1 & 2, Paquet 1987, 1988). The purpose of this paper is: a) to examine the type of 'dynamic'/'static? load test correlations that can be obtained. b) to highlight the differences between the classical' methods and the 'SIMBAT' technique.

Jan 1, 1989

By Sukeyuki Mori, Kinjiro Aso, Tsuyoshi Hara, Hisao Okamoto

A theoretical calculation of the electro-osmotic circulation of liquid in a rectangular micro-electro-phoresis cell was presented by Smoluchowski (1921) and Komagata (1933). According to their theories, the velocity of liquid changes with depth such that the velocity distribution may be represented by a symmetrical parabola in the cell. Their theories appear contrary to the results of our experiments which show that the velocity distribution curve is represented by a symmetrical parabola whose symmetrical axis is displaced from the center line of the cell. A similar phenomenon had been suggested by Lane and White in 1937 based on the latter's theory which seemingly was incomplete. By using methods of measuring electrophoretic velocities based on the above three theories, serious errors are obvious. We are thus proposing a unified theory for determining the electrophoretic velocity of mineral particles in a rectangular cell. The equations of Smoluchowski, Komagata and White can be derived from our theory as special cases. On the basis of our theory, we are proposing an improved method of determining the precise electrophoretic velocity of mineral particles based solely on the coefficients of the velocity distribution curve. In our experiments, this method gives satisfactory results. We determined the relation between the zeta-potential and pH value of suspension for several minerals.

Jan 1, 1980

About twelve months ago, owing to the increasing quantity of stone and dirt being drawn frQm the Victorian State Coal Mine due to the large amount of dead work below ground, cutting, faults, etc, and to the increasing quan#ty of banded coal beingworked, the writer was forced to consider the question of economy in handling the spoil at the surface. The method in operation at the time was to run out level dumps fro,m the, tipping floor of the heapstead, or brace, and to tip most of the skips of stone in tipplers at the ends of the dumps, the remainder of the skips being side-tipped to widen the dumps.The method, whilst quite satisfactory for dealing with a few skips of stone, was found to be costly as the dumps extended, and the number of skips to be dealt with increased from 300. to 400 per day of two shifts;. therefore, in order to expedite thework and cheapen its cost, the writer devised an improved method which may be qescribed as follows :-(1) The stone is tipped into a hopper car which holds about 10 skips(2) The hopper car is hauled up an inclined dump by means of an electric winch.(3) The spoil is dumped from the car forwards or to either side, as required.(4) The car is returned to the starting point for a further load.Plate I Fig. 1 gives an idea of the construction of the hopper car. In the illustration the car is in position for tipping to one side. The body of the car is supported on a ball race on the under carriage, and it can be swung round to tip in any required direction. The bottom of the hopper is extended to form a 4 ft. lip...

Jan 1, 1918

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of desliming, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants.

Jan 8, 1950

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) has been used by the mining industry for early fire detection in underground mines. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to integrate real-time AMS sensor data with NIOSH’s mine fire simulation program, MFIRE 3.0, to simulate and predict the spread of smoke that would provide assistance to mine fire emergency response personnel. Determining the heat release rate of a fire using the monitored sensor data was a critical component of the successful completion of this project. NIOSH researchers developed a direct method to calculate the heat release rate when a fire is within close range of sensors. However, this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire heat release rate for complicated scenarios where a fire is distant from sensors and airflow splits and merges are present. The method was validated using a fullscale diesel fuel fire test conducted in the Safety Research Coal Mine at the Pittsburgh Mining Research Division and can help mine operators and safety personnel make informed decisions during a fire emergency.

Jul 31, 2020

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) is used in the mining industry for early fire detection. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) have developed a direct method to calculate the fire heat release rate (HRR) when a mine fire is close to the AMS sensors, but this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire HRR using AMS sensor data at any location downstream of the fire. The method was validated using a full-scale diesel fire test conducted in the Safety Research Coal Mine at NIOSH’s Pittsburgh Mining Research Division.

By Julian Dimitrov, Kremena Dedelyanova

"The paper presents research on hydrodynamic processes occurring at the elementary act of flotation. Discussed existing models to determine the effectiveness of conflict of bubbles with particles in vibration column flotation machine. The paper presents a disperser for a column flotation machine, in which the dispersion of the gas phase is carried out using vertical vibration with defined frequency and amplitude. The paper presents research of mechanism for the creation of air bubbles in vibratory column flotation machine. The factors influencing the increase in the duration of the bubble in the area of contact with the mineral particles are discussed. Research was carried out on the effect of frequency and amplitude of vibrations on speed of precipitation of mineral grains of different density. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in vibratory column flotation machine is determined. The vibrations of the hydrated layer allow for cost-effective implementation of the elementary act of flotation by providing larger relative velocities at the contact point between the bubble and the solid phase. It is proposed to complement the model more accurate representation the mechanism of attachment of the particles to the bubble."

Jan 1, 2014

By J. S. Vanick

AN extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applica-tions requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small-grain grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By H. K. Fouad, L. A. Guirguis

The starting mill strip solution· for this study· is an ammonium uranyl tricarbonate solution of pH 8.2 containing 20g uranium/liter, after a DEPA/TOPO extraction process from sulfuric acid leaching liquor. To the first portion of the concentrated acidified strip solution, hydrofuoric acid is added at 95°C in reduced condition to obtain uranium tetrafluoride. The second portion of the uranyl carbonate strip is subjected to a precipitation step by admixing 0.3 volume of non-solvent precipitating agent such as acetone per volume of uranium. ·Uranium oxide (U30 8) is obtained from this precipitate by calcination for half an hour at 800°C in air. The third portion of the strip solution is neutralized to a pH 6.5 with sulfuric acid to precipitate iron and other contaminants. The solution is further acidified to a pH 1.85 with continuous air bubbling to remove CO2, followed by H2Ch precipitation at pH 3.5 to obtain uranyl peroxide. The latter is reduced by stannous chloride to obtain uranium trioxide dihydrate UO3. 2H20. Identifications, characterization· and purity of these products are carried out by complete chemical analyses, Scanning electron microscope study, tap density determination, X-ray diffraction and infrared spectroscopic investigations. The achieved results agreed well with that of the published data for these nuclear grade purity products.

Jan 1, 2000

By Anthony G. Fonseca

The acid leach-solvent extraction processing of oxide copper ores can be improved when selected cation additives are utilized. Bench scale testing showed improvements in both sulfuric acid leaching and solvent extraction processing. Treatment with the method to be described shows improvement in copper recovery in the acid leaching section as well as reduced acid consumption and reduced iron and aluminum dissolution. Processing the copper bearing leach solution with LIX-64N shows increased loading of the LIX reagent which relates to reduced aqueous and organic flow rates, reduced organic loss and inventory as well as a reduction in the size of mixer-settlers. The use of selected monovalent cations controls fluctuations within the pro- cessing system to accomplish the above named improvements. Additionally, these cations are totally compatible throughout the processing system and are quite inexpensive. Bench scale recycle data will be presented both for the leaching section and the continuous solvent extraction processing section up to (but not including) processing the loaded electrolyte. Material balances as well as major solution component monitoring will also be presented.

Jan 1, 1975

By A. J. S. Spearing, M. Sharifzadeh, K. V. Jessu

Empirical pillar design methods are commonly used in the mining industry. The parameters within which these methods are valid are frequently unknown to the user or ignored. In addition, empirical design may not consider essential parameters such as blasting effects, orebody dip and the presence of geological structures, which all adversely affect the stability of the pillars. This can result in potentially serious pillar design strength over-estimates. Although the commonly based tributary area method is generally conservative, as the spans are seldom that large relative to the depth, failing to consider other relevant parameters can result in errors. Problems associated with an under-designed pillar can range from a local pillar collapse to a catastrophic chain reaction collapse (or run). Over-designed pillars are generally safe but reduce the extraction of the orebody, thus adversely affecting the profitability of the mining operation. We used laboratory tests and numerical modelling to understand the effects of pillar orientation, blasting and the presence of discontinuities on pillar strength. Reduction factors were developed with these models to be implemented in conjunction with the existing empirical pillar design methods. For any pillar or mine design, once it is implemented, the actual performance of the system must be checked regularly by observation and monitoring and adjusted if needed. The pillar design approach outlined in this paper can better optimize the pillar mining method by considering other generally ignored but important parameters, thus improving safety, productivity, and economic aspects.

Oct 1, 2022

By M. M. Fine

One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. To cite some of them, in May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.3/ More recently, November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials, Evian, France, May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then current interest must be at a high level. To the casual observer of the metallurgical scene, the abiding and recurring attention to iron ore reduction outside the blast furnace must be somewhat puzzling in that so much research endeavor has resulted in so little commercial activity.

Jan 1, 1968

By C. A. Pickles

At the present time, pyrometallurgical processes are employed for the recovery of lead from battery scrap. These processes have serious pollution problems, primarily due to the emfssion of sulphur dioxide and airborne lead in the form of dust and fume. In addition it is necessary to dispose of solid wastes and liquid effluents which contain lead and in some cases sodium sulfide-containing compounds. In this work an improved process was investigated for the recovery of lead from battery residue. This involved pelletization of the residue with sodium carbonate and moisture. Then, the pellets were melted without carbon and the .sodium sulphate salt was removed. Subsequently, the molten lead oxide was reduced with carbon. This process minimizes the sulphur dioxide emissions and leads to very low sulfide contents of the sodium sulfate salt

Jan 1, 1992

By H. D. Freeman

The Pacific Northwest Laboratory (PNL) is developing cover technology for uranium mill tailings that will inhibit the diffusion of radon to the atmosphere. As part of this cover program, an improved radon flux measurement system has been developed. The radon measurement system is a recirculating, pressure-balanced, flow-through system that uses activated carbon at ambient temperatures to collect the radon. With the system, an area of 0.93 m2 is sampled for periods ranging from 1 to 12 h. The activated carbon is removed from the radon trap and the collected radon is determined by counting the 214Bi daughter product. Development of the system included studies to determine the efficiency of activated carbon, relative calibration measurements and field measurements made during 1980 at the inactive tailings pile in Grand Junction, Colorado. Results of these studies are presented.

Jan 1, 1981

By Bruce B. Redpath, Thomas E. Ricketts

Scaling laws commonly used for describing or predicting blast motions generated by conventional arrays of blastholes are dimensionally incorrect. The scaling of distance by the cube root of charge weight is correct only for spherical charges, and scaling by the square root of charge weight is incorrect for any charge configuration, although both approaches may result in empirically useful formulas for a limited range of charge sizes. Analysis of motions generated by a large set of underground blasts shows that scaling distance by the square root of the linear charge density, which is dimensionally correct for a cylindrical borehole, yields much more consistent results than the traditional scaling rules. Further, this scaling law is valid right up to the free face of the burden. A significant result of this work is that the peak particle velocity for an array of blastholes is primarily dependent on blasthole diameter and not on total charge weight or maximum explosive weight per delay, which are the commonly used parameters for scaling seismic amplitudes generated by conventional blasting arrays.

Jan 1, 1987

By L. G. Austin

The model originally proposed by Austin, et al., has been modified in the light of further investigation of the breakage laws in SAG milling. The model uses a fully-mixed reactor for short L/D mills and calculates the breakage of small particles by the nipping action of balls and pebbles. The autogenous self-breakage of larger lumps is treated as an effective means of fast breaking rock and much slower breaking rock. Experiments show that fast autogenous breakage can be treated as a first-order breakage with an overall specific breakage rate which incorporates fracture and chipping. Similarly, slow breakage incorporates fracture and abrasion. Autogenous breakage is cushioned by the accumulation of fine material. Simulation results are compared to results from tests in a 2 m diameter continuous pilot-scale SAG mill. Future work is discussed.

Jan 1, 1985

By Thomas E. Ban

The continuous sintering process was invented more than 60 years ago by two metallurgists, Arthur S. Dwight and Richard L. Lloyd, who saw a need for automation in mineral processing. Their specific objective was to beneficiate copper ore by desulfurizing and agglomerating it for copper blast furnace smelting at the Cananea plant in Mexico1. Since their early development the process expanded widely in scope, size, and application. The current worldwide sintering applications exceed 250 million tons per year for agglomerating ores of lead, manganese, zinc, and iron. Sintering is also widely used for production of sintered lightweight aggregate from clays, shales, and fly ash. The continuous sintering process took on wide expansion during the 1960's in foreign countries. Plants for production of approximately 135 million tons per year were built in these countries for sintering iron ore fines as shipped from new iron ore projects of Canada, Liberia, India, Brazil, and Australia. This expansion represented construction of approximately 80 new sintering plants, some as large as 15 thousand tons per day production on a single large sintering machine. Sized self-fluxing or highly fluxed sinter has become recognized as a premium blast furnace charge and has enabled blast furnaces of Japan and Europe to produce upwards of 10,000 tons of metal per day with coke rates less than 1,000 pounds per ton of metal. This coke requirement is practically 50 percent of the ordinary rates achieved during the early 1950's when the peak blast furnace production was less than 113 of the current records.

Jan 1, 1975

By Ellsworth Daggett

THE system of pitwork used with the Cornish pumping engine, and which, for want of a better name, we may call the Cornish system of pitwork, consists essentially of a series of plunger-pumps, situated one below the other, in a shaft or incline, the plungers being operated by a rod called the pitman or pump-rod, which must, therefore, extend from the motor at the surface to the lowest pump. The subject will be best understood by reference to Fig. 1, in which k may be taken as typical of the ordinary plunger-pump, in which S is the suction pipe, u, the lower valve situated in the H piece T; v, the upper valve situated in the valve-box O; I, the mounting-pipe or column through which the water is carried to the surface; L, the plunger-barrel, and P, the plunger working through the stuffing-box, and actuated by the branch rod r, which is attached to the main pump-rod, R. The action of the pump is as follows : On the ascent of the plunger, acting now by suction, the water flows from the reservoir through the valve u, into the barrel, L. On the descent of the plunger, the water is forced up through the valve, v, which acts merely as a check valve, into the pipe, I, through which it is, at each successive down-stroke of the plunger, forced upward until it reaches the next reservoir, from which it is taken by another similar pump, and so on until it reaches the surface or drain-tunnel. The pump is obviously only single-acting, i. e., it acts only during one-half of its entire stroke. The weight of water raised during the up-stroke of the plunger is equal to the weight of a column of water whose base is the area of the plunger and whose height is the mean distance between the plunger-face and the surface of water in the lower reservoir, a distance not usually exceeding 12 or 15 feet, and which obviously cannot under the most favorable circumstances, exceed 25 or 30 feet. The water forced up during the down-stroke is equal to the weight of a column of water whose base equals the area of the plunger and whose height equals the length of the mounting column above the mean position of the plunger-face, say from 150 to 300 feet. Almost all of the useful work, therefore, is done on the de-

Jan 1, 1879