Search Documents

By Roger B. Alke

INTRODUCTION Request to Mine Beneath Bridge The Jakes Run Bridge is a reinforced Portland concrete arch filled bridge located on WV Route 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Fig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old having been built in 1929 and is owned by the Department (WV Department of Highways). [ ]

Jan 1, 1984

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By Karen Dawson

This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.IntroductionStone column ground improvement was implemented as a means of supporting mechanically stabilized wall approaches for a new bridge over the Puyallup River, part of HOV improvements to I-5 in Tacoma, Washington. The work discussed in this case history was part of the Washington State Department of Transportation (WSDOT) I-5/Portland Avenue to Port of Tacoma Road, Stage 1 Northbound HOV contract, developed as an early work element to a follow-on bridge construction project. The area requiring stone column ground improvement is shown in Figure 1. The improved ground supports permanent geosynthetic walls and embankments up to 50 feet high. This wall can be seen in Figure 1. The selected ground improvement primarily provides global stability of the soils beneath the walls during anticipated seismic loading and also reduces the time and magnitude of consolidation settlement under the weight of the planned embankment.Approximately 74,000 cubic yards of liquefiable alluvial soils were improved by stone columns. Stone column construction occurred in late 2010 and early 2011. This was followed by the embankment and wall construction. Settlement monitoring began with the embankment construction and continued into 2012."

Jan 1, 2017

By Suthan Pooranampillai

This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.IntroductionCement deep soil mixing (CDSM) was used as a replacement for stone column ground improvement in a corridor which the owner, the Washington State Department of Transportation (WSDOT) wanted to reserve for future trenchless crossings beneath reinforced soil embankments within a freeway interchange. The work was part of HOV improvements to I-5 in Tacoma, Washington. The CDSM construction occurred in late 2010 and early 2011.Approximately 14,500 cubic yards of soil cement columns were placed by CDSM. The soil cement improved ground supports permanent geosynthetic reinforced slopes up to 50 feet high. The ground improvement was designed primarily to provide global stability of the reinforced slopes during seismic loading, but it was also utilized to reduce the time and total amount of settlement following construction of the embankments.This paper presents a discussion of the design approach and challenges associated with quality assurance of a relatively small volume of CDSM within the time constraints of an ongoing project. The challenges associated with attempts at collecting cores of the cured soil-cement mix cured by triple tube coring and pushing a double tube into the wet mix and allowing it to cure insitu are discussed, along with the eventual adoption of sonic coring combined with reliance on laboratory testing of wet mix samples collected daily."

Jan 1, 2017

By K. Lagnese, C. Robinson, S. Muddasani

"Mine water generated from underground coal mining operations contains both dissolved and particulate solids. Dissolved solids primarily consist of sodium, calcium, magnesium, potassium, chlorides and sulfates. When discharged to a receiving stream without treatment, these constituents create a potentially toxic environment for aquatic life. A case study is presented to discuss how a centralized treatment plant treats mine water from six locations to meet discharge limitations for chlorides. Located in West Virginia, this facility consistently achieves less than the NPDES permit limitation of 218 mg/L chlorides in the discharge while generating almost zero liquid waste. The dissolved solids concentration in the influent ranges between 5,000 and 10,000 mg/L, with chloride concentrations of 1,000 to 2,000 mg/L and sulfate concentrations of 2,000 to 6,000 mg/L. The mine water is treated using advanced treatment technology to produce clean water for discharge or reuse. The treatment process comprises aeration, softening, filtration, reverse osmosis, RO reject softening, evaporation, crystallization, final effluent remineralization and sludge dewatering. The solid waste generated in the treatment process is landfilled on site. The leachate is sent back to the facility’s thermal treatment process. Because no liquid waste leaves the property, this plant is termed a “Zero Liquid Waste” (ZLW) facility. INTRODUCTION The advanced water treatment system was built to meet a new 218 mg/l regulatory limitation imposed by the West Virginia Department of Environmental Protection for chlorides discharged to surface waters. The system is designed to treat a maximum flow of approximately 5 million gallons per day (795 m3/h) of mine water. The treatment process utilizes reverse osmosis (RO) membrane treatment to achieve the effluent criteria, and evaporation and crystallization technology to manage the RO concentrate from the water treatment process. As a result, the system produces clean water for discharge while generating zero liquid waste. The effluent water can be used for industrial purposes or discharged to a receiving stream. A Water Impact Index (WIIx) study indicated that discharge of this high-quality water into the Monongahela River watershed may improve the water quality for downstream water users. The waste produced in the treatment process, including softening sludge and salt, is disposed of in an on-site landfill."

Jan 1, 2015

By Feng Yongxuan

Anchored sheep pile is normally used in deep excavations, many of which only require stability in accordance with Terzaghi theory. In this paper, based on the experience, new lateral earth pressure method is adopted taking account into interaction among soil, anchors and sheet piles so that a group for the project under very difficult conditions and very severe requirments, especially, for the displacements are determined according to that mentioned above. During and after construction, displacements monitoring were carried out for about four months, which was proved that there was a little difference between calculation and practice.

Jan 1, 1991

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015

By T. O. Price

In 1969 Holosonics designed and developed a portable system for conducting acoustical surveys in metal mines, with lead-silver veins as the principal targets. Recently this system has been proven useful in describing rock structures for advance geologic information in civil engineering application and underground construction applications. This paper discusses a case history of acoustical surveying from a series of pilot drill holes in an advancing tunnel. In acoustical surveying a pulsed acoustic signal is used to generate reflected signals from the rock formation. Arrival time, amplitude and phase of the returned signals can be determined. These data became the basis for a signal correlation program designed to relate the signals to their respected pseudo-planar reflecting interfaces. An application of acoustical surveying has recently been conducted in a portion of the excavation for the Washington Metro Area Transit Subway. The data results and conclusions of the program are discussed in the paper. Acoustical surveying was successful in predicting the occurrence of major jointing and foliation plane shearing ahead of the tunnel advancement.

Jan 1, 1974

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

The care necessary to ensure a reliable estimate of average value from the individual values of a series of bore holes sunk in any alluvial deposit containing coarse gold was well exemplified in checking over the mining returns from a previously bored deposit in Central Otago, N.Z. While the working returns are always liable to vary considerably from bore values in any particular sub-section of an area, still, over any considerable area, the two must check within small limits, if profits are to be calculated and capital raised on the average value given by boring.The present figures have probably more value than those from, dredge returns since accurate measurements are difficult to obtain in irregular water-filled dredge paddocks, whereas in the case under review the paddock walls stood almost perpendicular, and, as the measurements were taken and checked in the empty rectangular excavation, the yardage estimate may be taken as substantially exact.NATURE OF DEPOSITThe area consists of a narrow valley deposit of fluvio-glacial origin, the original deposit having been eroded and the gold reconcentrated by post glacial rivers. The wash is between 80 and 90 ft. deep, and is formed in two distinct layers:(i.) The top layer from surface to 70 ft. or 80 ft. consists of about equal quantities of gravel mixed with glacial drift, and a small amount of clay. The gravel is typical discoid glacial stone of a maximum size of about 4 in. diam. by 1 in. thick, and consists of soft micaceous schist and laminated slate. This upper layer of wash contains no coarse gold whatever, and very little fine; indeed, in mining, the top 30 ft. is discarded without being passed over the boxes.(ii.) The lower layer of wash to bedrock is similar to the upper, except iihat it contains about 10% of larger discoid stone up to 12 in. diam. by It in. thick; 90% of the gold is concentrated in this bottom layer.

Jan 1, 1929

By J. L. Christie

A recent case of failure of a-low karat gold alloy by stress-corrosion cracking is of interest because it illustrates a principle frequently overlooked: the relation between high residual stress and high yield point. The alloy contained Gold, per cent 39.6 Copper, per cent 51.1 Silver, per cent 5.2 Nickel. per cent 3. 1 Zinc, per cent 1.0 Tension tests on the alloy showed the following:

Jan 1, 1945

By Jean Wehbe, Daniel C. Brahana

"This paper presents a case history of drilled pier construction for a new stadium in Atlanta, Georgia. The stadium structure is supported on several different foundation types, with the heaviest ""mega columns"" typically bearing on drilled pier supported mats. The project includes 141 drilled piers with design diameters of 5.5, 6 and 6.5 feet. The piers bear on bedrock at depths of 20 to 110 feet below the ground surface. Many of the piers included rock sockets with design lengths of 5 to 18 feet. A pre-production drilled pier load test program was completed including one Statnamic load test, two Osterberg Cell tests and two lateral load tests. Non-destructive testing (crosshole sonic logging and sonic integrity testing) were also performed during construction. Production pier installation with over 3800 linear feet of earth excavation and over 1350 linear feet of rock excavation was completed in a little over four months. The piers were installed using both the cased hole method and the slurry method. All cased holed required downhole inspection and slurry holes were initially inspected with a mini-SID device and subsequently by sounding. Advanced drilling equipment and tooling were used to meet the production requirements for the project. This paper reviews the highly variable soil and rock conditions encountered at the site, briefly presents the results of the load tests, and discusses pier installation procedures and the equipment used for installation. The paper also presents conclusions related to the installation and lessons learned.INTRODUCTIONWith the opening of AT&T Stadium in Dallas, a new era of stadium construction began in the U.S. The new age stadiums are larger and have more amenities than their predecessors. The new Atlanta Falcons stadium is no exception. Many of the new features, including Atlanta’s innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are drilled pier supported. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 feet. Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings are used to support the more lightly loaded portions of the structure."

Jan 1, 2017

By Charles Clark, Mark Mukhija, Jaime Klein

Comminution – the reduction in size of solid materials – is the most energy intensive component of the mining process (Bauer, 2015). It is estimated that comminution consumes around three percent of all electricity generated in the world (Ceecthefuture.org, 2017). On an energy equivalent basis, downstream processing consumes six times more energy than drilling and blasting (Kanchibotla, Sarma et al., 2014).

Jan 1, 2018

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By C. McAllister, D. Preece, J. Berendzen

The Multiple Blasthole Fragmentation (MBF) model was developed recently and has been reported in previous papers. The MBF model accepts inputs from the blast design, such as: location and orientation of each blast hole, stemming length, blast hole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect on fragmentation of delay timing with its associated scatter for each blast hole. MBF has a statistical modeling capability for geological random variation of the attenuation of particle velocities. Also simulated is wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges.

Jan 1, 2016

By Chris Leach, Lucie Spencer

This case study describes the geotechnical aspects of the basement construction for a multi-storey, residential and hotel complex located in the newly developed Elizabeth Quay precinct in Perth, Western Australia. The development included a three-level basement for car parking covering the full site area which was constructed using the top-down construction sequence. Soil conditions generally comprised 2m of fill overlying medium to dense clayey sands that in turn were generally overlying a very stiff clay stratum at approximately 13m depth. Bedrock level was generally encountered at approximately 22m to 35m below ground level. The ground water table was at a depth of approximately 1m below the existing ground surface level. A site boundary basement wall was constructed using a diaphragm wall retention system. The majority of the vertical loads from the building were transferred to the Kings Park Formation (KPF) bedrock through the use of foundation piles constructed by the CFA method. The CFA piles were installed from existing ground level, resulting in approximately 9m sacrificial concrete length from pile platform level to basement 3 (B3) level. The permanent column loads are such that a single CFA pile was not structurally adequate. To allow a full CFA foundation system to be adopted, an innovative design and construction approach was developed for these heavily loaded columns. This paper discusses the site technical details and the design and construction aspects required to meet the challenges offered by this project.

Nov 1, 2022

By Ali Keneti, Xavier Ryan, Gerardo Sanchez, Shannon Goff

In this study, FLAC3D modeling was conducted for ground-structure stability assessment for a pilot tunnel passing under a large shaft excavated in the vicinity of existing structures at Karangahape Station for the City Rail Link Project in Auckland, New Zealand. The analysis involved generation of the geometries and construction sequences in Rhinoceros®, modeling the existing ground condition, calibration of the simulated in situ conditions with the observed behavior of the ground, and excavation of the shaft and the pilot tunnel. A comprehensive interpretation of the results was then performed accompanied by comparison of the predicted behavior with the observed response of the ground during construction.

Dec 1, 2022