Search Documents

By Bennet A. G

An overall review of the selection of rock strength and deformation characteris- tics for the design of the Melbourne Under- qround Rail Loop (MIJRL) rock tunnels is presented. Particular emphasis is placed on aspects of in-situ testing, including large diameter plate bearing tests. Material on the interpretation of test results for use in the design of the tunnel linings and openings is included, with a brief discus- sion of desiqn methods.

Jan 1, 1981

By Bror Nyman

Wide settlers are a way to decrease the linear velocities of advancing liquid phases. It has, however, been found unnecessary to risk a proper settler performance by building shallow settlers in order to avoid a so-called interface turbulence due to a too big difference between the linear velocities of the organic and the aqueous phase. This conclusion has been reached from tests using a large transparent settler model, where the behaviour of a clean interface between two advancing liquids has been investigated. Also in a more realistic case, making an organic in aqueous or an aqueous in organic dispersion to move between the liquid phases, no obstacle has been found to use a somewhat more deep and correspondingly ore slowly t10wing aqueous phase. Based on above findings, support can be given to a new trend to build the settlers slightly deeper than what has been typical for the so-called low-profile design. In this way, it is much easier to avoid an excessive air introduction and other severe difficulties, like those caused by crud moving from one stage to another. It is further shown, how gravity can be used to slow down and distribute a dispersion being fed into a settler of a VSF unit. Entrainment levels have been found to be reduced by a careful design of primary dispersion distributors and picket fences of the settler. Finally, it is demonstrated, how outlets from the side of the settler can be used to simplity interstage pumping and to decrease the rotation speed of any pumping device.

Jan 1, 1996

The coal resources of the Singleton- Muswellbrook area of New South Wales are of major importance to Australia, and are likely to play a significant role in meeting the expanding demands for energy in many countries of the world. Coal resources of 45 thousand million tonnes of which 15 thousand million tonnes lie at a depth of less than 200m have been estimated. The history of coal mining in the area commenced in the mid 1800's and has been one of fluctuations in production but of rapid expansion in more recent years. It is destined to become the largest coal producing area in New South Wales. Coal is being won from the area by strip mining, open pit mining and by underground means. The techniques involved are described. The area is well endowed with infra- structure such as modern towns, railways, road- ways and access to port facilities. Production of both coking coal and steaming coal is expected to rise significantly within the next 25 years. A large proportion of the State's anticipated increased production to between 117 and 177 million tonnes by the year 2000 is likely to come from this area.

Jan 1, 1979

By Cagri Emer

In conventional mechanical flotation cells, when the size of particles exceed a particular value, that is of the order of 100 µm for metal sulphides, the recovery of particles decline rapidly. It appears that the turbulence in the agitated vessel is sufficiently intense to rupture the forces of attraction between the particles and the bubbles, so the large particles are flung off the bubbles in the turbulent field. It has recently been suggested, that a fluidized bed would be a very favorable environment in which to contact bubbles and the particles. In a fluidized bed, particles are supported by rising flow of fluid, which separates them from each other and allows them to move freely while remaining close together. In this novel method, bubbles injected into the fluidized bed are able to rise through it, colliding with hydrophobic particles, transporting them to the top of the column where they can form a froth layer that overflows into a launder. The flow in a fluidized bed is generally slow and nonturbulent, and preliminary experiments have shown, that it is possible to collect mineral particles as large as 1 mm and coal particles as large as 5.5 mm. If the upper particle size limit can be extended, there could be significant reductions in the overall energy consumption in concentrators. Calculations show for example that if the top size for flotation could be increased from 100 µm to 400 µm, there would be a reduction in grinding energy of the order of 40%. It is therefore, important to study the mechanism of coarse particle capture in fluidized beds. In this work, the factors governing the capture rate of particles, particularly the particle and bubble size, the fluidization velocity and the superficial gas velocity have been investigated, and the results will be presented.

Sep 1, 2012

By M. B. M. Monte, M. L. Torem, E. R. Pecanha, A. G. Merma

The recent literature has unveiled the potential use of microbial strains in mineral bioprocessing. This study presents the use of a Gram-positive bacterium (Bacillus subtilis) as bioreagent for hematite flotation. The bacterium presents the ability to modify the properties of mineral surface (electrophoretic mobility and hydrophobicity). It was studied the electrokinetic behavior of hematite particles, before and after the interaction with the bacterial cells. The results revealed a shift of the isoelectric point (IEP) of the hematite after interaction with bacterial cells, suggesting a chemical adsorption mechanism. Moreover, after bacterial conditioning, the zeta potential curve of hematite presented high values in the alkaline pH range. The hematite and the bacterial surfaces presented contact angle values around 27.4° and 41.0°, respectively. According to the results, the B. subtilis strain was capable of modifying the hematite surface, and after interaction the hematite surface presented a contact angle value around 46.0°. The flotation tests were carried out in a modified Hallimond tube. The experiments revealed a significant increase in hematite flotability using the Gram-positive strain as bioreagent. The tests pointed out a maximum recovery of hematite in the presence of 600 mg/L and pH 5. Therefore, the results from this study showed the potential use of the B. subtilis strain as a biocollector for hematite flotation, and its possible application in the mineral flotation industry.

Jan 1, 2016

By José Luiz Rodrigues Bravo

The production of electrolytic copper with assured quality corresponding to international standards, in a conventional electrorefkery of a custom smelter, is a hard and cautious task, if no advanced technologies for selective control of electrolyte impurities are available. The improper control of the amount of As , Sb and Bi in the anode that enter the tankhouse , attributable either to a bad schedule of concentrate input or to the unavailability of clean concentrates in the international market , as well as the lack of means to maintain the suitable level of these elements in the electrolyte together with other operational circumstances, can result in off-grade copper, as well as affect the starting sheet chemically and physically. This paper presents in a practical way the relationship between the operational conditions and the cathode and starting sheet quality produced at CMSA, covering the period of the last five years of operation, discusses the technologies available in the market for antimony and bismuth removal and compare the results of testwork, achieved in the laboratories of CMSA, using two resins not associated with patented technologies.

Jan 1, 1997

Severe development difficulties were experienced soon after in-seam mining commenced at Appin Colliery in'1962. Thirteen years later no significant pro- gress had been made in overcoming some aspects of this development problem. Some success had been achieved in destressing roadways both in development and pillar extraction. Longwall retreat mining had shown promise of being highly productive but at an extremely high cost in terms of development requirements both in number of roadways and intensity of support in those roadways. No real advance was made in the problem of driving the first heading of a group of headings under conditions of apparently high stress in directions other than the preferred mining directions, although failure of the roof in this heading did seem to give easier work in the subsequent headings driven particularly if they were driven on narrow centres.

Jan 1, 1976

Incremental sampling is defined as a solution to fight segregation, the theory is demonstrated and theoretical and practical aspects are discussed. The number of increments necessary for successful sampling is discussed. As an application, riffle splitter division is reviewed.

Mar 1, 2010

By Flanelson Maciel Monteiro, Yago Lutz Castro Pinto, Marcondes Mendes de Souza, Mauro Froes Meyer

This article is based on a bibliographical review of a field work that was done in the Salina São Camilo in the region of Mossoró - RN. The general objective of this research is to present the main exploratory and beneficiation aspects of salt production. Among the aspects of salt is the properties of salt, history and mining, besides the aspects of environment and work safety. However, this research resulted in preliminary data, but it would be interesting to be more thorough so that the extraction of salt in the academic world is disclosed

Oct 3, 2019

By C. J. V. Wheatley

Recent studies of the mineralisation at Avoca in southeast Ireland, Parys Mountain in Anglesey, and Coniston in the Lake District result in the proposal of a new metallogenetic model for mineral deposits in the Southern Caledonides. A regional pattern of metal zoning exists, an axial belt, including the major copper deposits, being bordered by areas with lead-zinc deposits. Conformable lenticular pyritic zones occur in the central belt, closely associated with acid volcanic sequences and, often, post-dating them. These zones are thought to have been formed in a marine environment, mineral growth taking place below the sediment-water interface, whereas magnetite-rich zones developed under different Eh and pH conditions. Stockworks containing appreciable copper and, in some cases, lead and zinc were developed at a later date, stratigraphically below the pyritic zones, by migrating hydrothermal chloride and metal-rich fluids. Complex lead-zinc-pyrite mineralisation resulted from the reaction between pyritic zones and the final fraction of the hydrothermal fluids. Crosscutting vein-type fissure infilling mineralisation occurs in every mineral field. These deposits apparently comprise a pulsatory metasomatic sequence, closely related to tectono-stratigraphic controls, ore localisation being influenced by the coincidence of suitable structures and pyritic shale horizons. The implications for mineral exploration are considered and it is concluded that the model offers an explanation for the existing pattern of metal zoning; and it may have wide applicability to mineral deposition in geosynclinal sequences.

Dec 1, 1971

By Cuff C, Taylor RG, Georgees C

Mineralisation adjacent to Herberton occurs within three main subcentres. The Her- berton Hill subcentre is characterised by the association of Sn,W the Herberton Dividing Range South subcentre by Sn, and the Herberton Dividing Range North by Cu, As. The relation- ships between the subcentres are discussed in terms of metal distribution, production, deposit types, wall rock alteration and re- lationships with granitoid intrusives. The temporal and three dimensional spatial re- lationships between the centres are uncertain.

Jan 1, 1978

By Zwaan J, Kepa J

Ok Tedi mine has become one of the major copper producers in the world. In the process of becoming of age, it overcame the challenges of operating in a locality which is young in geological terms, experiences very high rainfall and has a topography which gives rise to frequent landslides. This paper discusses some of the geological, mine and geotechnical engin- eering aspects of the Mt Fubilan ore deposit.

Jan 1, 1991

The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members Ñ the Universities of Queensland and Sydney and the CSIRO1, and by its industry members Ñ BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining.

Jan 1, 2001

"The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members — the Universities of Queensland and Sydney and the CSIRO1, and by its industry members — BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining. Mechanized Rock ExcavationThe disadvantages of the drill-and-blast excavation method are widely recognized and the last half of the 20th century has seen mining companies and mining research organizations aggressively pursue technology to excavate rock by other means. As discussed below, despite considerable effort and large amounts of funding, the quest for mining’s “Holy Grail” has been unsuccessful in all but the weakest rock types.COMRO (the Chamber of Mines Research Organisation) supported by the South African gold mining industry, spent three decades and (probably) tens of millions of dollars developing prototype drag bits and, later, impact breaking machines aimed at the mechanized stoping of narrow, tabular reefs. This work has not yet produced a commercially-attractive mining system. Work continues in South Africa to mechanize these stoping operations although now the emphasis is on the use of diamond-wire sawing techniques. This work remains in the experimental phase.Both British Coal and Germany’s Bergbau- Forschung spent many years developing techniques trying to extend the range of rock types which roadheaders could cut economically. Again, although new knowledge was produced, it is difficult to claim that any new commercial mining systems emerged from this work."

Jan 1, 2001

Process variables in flotation circuits are outlined with a view to producing mathematical models of circuits. The nature of the kinetics of flotation are discussed and the effect of process variables on the kinetics considered. An approach for a possible model is briefly outlined.

Jan 1, 1971

By E. C. I. Hammerbeck

"Geological controls and constraints in space and time define the milieu of the nickel deposits of Southern Africa. Primary, magmatic deposits are of two types, e.g. synvolcanic or syntectonic deposits confined to certain orogenic domains, and those related to intracratonic, post-orogenic magmatism, e.g. the Great Dyke, the Bushveld Complex and the Insizwa intrusion. Epigenetic and supergene deposits form a separate, unrelated group and are of minor economic importance.The metallogenic evolution of syntectonic nickel deposits is particularly well illustrated in the Zimbabwean Province, where the relationships between Archaean greenstone development and nickel mineralization are best illustrated. Volumetrically subordinate, nickel-poor greenstones in the 3500 m.y. old Sebakwian Group are followed by more common komatiite development in the Lower Greenstones (3000 m.y.), and, finally, by very significant komatiites with important nickel mineralization in the 2700 m.y. old Upper Greenstones of the Bulawayan Group. Comparable nickel mineralization is not known in the Raapvaal Province, in spite of ubiquitous komatiitic magmatism of the Onverwacht Group (3500 m.y.) and other greenstone sequences. No komatiitic rocks younger than about 3200 m.y. are known in this region, orogenic activity in the Kaapvaal tectonic province having ceased at about 3100 m.y., whereas the Zimbabwe Province remained tectonically active until at least 2600 m.y.The tectonic environment, host-rock petrology and mode of emplacement, as well as some details of the nickel mineralization, are the parameters employed to classify the Southern African magmatic nickel deposits. A rating of the deposits is introduced that reflects the original resources of the deposit, its average nickel content, its mining history and potential to facilitate ready comparison with and assessment of the nickel deposits listed in the classification, as well as some important nickel deposits worldwide."

Jan 1, 1984

By Paul Krivokuca

Outline Quinsam Coal Mine ?? Location ?? Mine History ?? Safety ?? Production ?? Hiring 4S Mine ?? Depillaring design ?? Structural mapping, Risk assessment ?? Rock Bolt Design Selection ?? Training

May 1, 2008

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

This paper provides a review of the chemical reactions occurring in the submerged arc processing of chromite ores. The excavations of industrial furnaces have shown that the charge, as it descends through the furnace, passes through a number of distinct reaction zones. Each zone is characterised by differing process conditions and reaction products. The phase equilibria, reaction steps and mechanisms occurring as the charge progresses through the furnace are examined, and the potential influences of these factors on the process outcomes are discussed.

Jan 1, 2004

By A. A. Hejja

The first part of this study deals with the importance of surface tension of slags produced in the smelting of sulphide concentrates. Theoretically the method of determining the surface tension of slags was laid down by Boni and Derge. The values obtained experimentally for a series of main oxide components were grouped into a useful correlation incorporating experimental constants for the relevant oxides present in the slag, some of these giving the surface tension value for the particular slag. These estimated values were coupled with or incorporated into the slag viscosity plots to show the correlation between the two factors. This is also important from a refractory attack point of view in the furnace operation. In the second part an attempt is made toward the optimisation of slag composition relevant for electric furnace smelting processes. Using the knowledge of the viscosity and electrical conductivity of the slags at the temperature of furnace operation, the mode of optimisation is based on correlations which utilize the trend of the mostly parabolic plots of viscosities and conductivities. The results obtained by this method agree well with the optimum slag compositions being used in established operations derived from years of practical experience for various slags used in the furnaces. However, due to extensive turbulence in suspension and gas injected bath smelting processes, the outlined methods cannot be used for these processes. Also great caution should be exercised in their application for three electrode circular furnaces with separate slag cleaning.

Jan 1, 1997