Search Documents

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021

By A. A. Zatout, G. H. Sedahmed, T. M. Zewail, M. H. Abdel-Aziz, B. S. Ibrahim, E-S. Z. El-Ashtoukhy

In this work, the possibility of intensifying the cementation process in stirred vessels was studied by using the perforated baffles as turbulence promoters; the cementation reaction of Cu+2 on Zn was selected as a model. Zn was used in the form of a sheet lining the inner wall of an agitated vessel. Parameters considered are initial concentration of Cu+2, solution temperature, impeller rotation speed, and impeller geometry. Within the present range of parameters studied, the rate of cementation was found to increase with increasing initial concentration of Cu+2, solution temperature, and impeller rotation speed. At the same rotational speed, a flat turbine gave a higher rate of cementation than a 45° pitched turbine. The present suggested that baffles’ geometry gave superior performance in terms of mass transfer of copper cementation compared to the conventional baffle geometry. All parameters that affect the rate of cementation were correlated in the form of dimensionless equations suitable for the design and performance prediction of the agitated vessel. Potential applications of the obtained results in the field of hydrometallurgical processes and wastewater treatment were discussed.

Jan 12, 2021

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Hypochlorite leaching system is a strong oxidizing solution for metal sulfides, which are naturally associated with gold extraction. This study evaluated the hypochlorite leaching of refractory gold ore by using the response surface method–central composite design (RSM-CCD) as a statistical approach in determining the optimum condition of gold extraction from refractory gold ore. The studied parameters for the gold recovery were pH (4 to 6), concentrations of Ca(OCl)2 (0.5 to 1.5 M) and NaCl (2.5 to 3.5 M) in the solution. It was found that the maximum gold extraction of 82.46% (13.85 g/t) was achieved at a pH of 4.0 with NaCl and Ca(OCl)2 concentrations of 2.93 M and 1.08 M, respectively. The statistical analysis also revealed that the amount of gold recovery in chloride solution was significantly depended on pH as the main factor, followed by concentrations of Ca(OCl)2 and NaCl.

Jan 8, 2021

By Liaqat Ali Shah, Muhammad Farooq, Zait Ullah Shah, Francisco Rolando Valenzuela-Díaz

Bentonite collected from Nowshera (Pakistan) was treated with NaCl, and the < 2-μm clay fractions were separated by sedimentation process. The textural changes in NaCl treated purified bentonite were compared with raw and physically purified sample. It was detected that the NaCl-treated purified bentonite and the sample purified by simple sedimentation, respectively, consist of sodium-montmorillonite and calcium-montmorillonite as a major clay mineral. The honeycombed-type morphology was observed for both the purified samples; however, the particles of NaCl treated purified bentonite were relatively in a compact form. The particle sizes of both the purified samples were found considerably smaller. The high volume percent of the fine particles was noticed in the NaCl-treated purified bentonite. This attributed that the sodium exchange has a valuable impact on the bentonite dispersion in aqueous media during particle size measurement. The relatively high mesopore area/volume and micropore area/volume and specific surface area (SSA) were detected in purified samples. The NaCl-treated purified sample showed relatively high mesopores area/volume than the sample obtained by simple sedimentation. These changes seem to be originated from either high montmorillonite contents and/or the smaller particle size, which might be produced after the layer rearrangement during the interlayer cation replacement by Na+ ions. The large SSA and high porosity of purified samples particularly the NaCl-treated bentonite suggest their potential use as adsorbents, catalysts, pharmaceuticals, and cosmetics.

Jan 7, 2021

By Ihsan Berk Tulu, Mark Alexander Van Dyke, Deniz Tuncay, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies, personnel, and the dilution of mine air contaminants. By design, these entries must stay open for many years for ventilation. Standing supports in moderate cover bleeder entries were observed, numerically modeled, and instrumented by researchers at the National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in this paper in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar, or supports are to the gob, the greater the applied load due to rear abutment stress.

Jan 7, 2021

By Mei Long, Tawum Juvert Mbah, Jianhua Zhang, Haiwang Ye

There have been many improvements and advancements in the application of neural networks in the mining industry. In this study, two advanced deep learning neural networks called recurrent neural network (RNN) and autoregressive integrated moving average (ARIMA) were implemented in the simulation and prediction of limestone price variation. The RNN uses long shortterm memory layers (LSTM), dropout regularization, activation functions, mean square error (MSE), and the Adam optimizer to simulate the predictions. The LSTM stores previous data over time and uses it in simulating future prices based on defined parameters and algorithms. The ARIMA model is a statistical method that captures different time series based on the level, trend, and seasonality of the data. The auto ARIMA function searches for the best parameters that fit the model. Different layers and parameters are added to the model to simulate the price prediction. The performance of both network models is remarkable in terms of trend variability and factors affecting limestone price. The ARIMA model has an accuracy of 95.7% while RNN has an accuracy of 91.8%. This shows that the ARIMA model outperforms the RNN model. In addition, the time required to train the ARIMA is than that of the RNN. Predicting limestone prices may help both investors and industries in making economical and technical decisions, for example, when to invest, buy, sell, increase, and decrease production.

Jan 6, 2021

By S. Michael, T. E. Moongo

Electrowinning consumes a substantial amount of electrical energy, and owing to the ever-increasing unit cost of electrical power there is a need to improve current efficiency in the process. This research was carried out to design a continuous quality improvement framework for improving electrowinning current efficiency by applying statistical process control (SPC) on an online industrial copper electrowinning operation. A sequential mixed research methodology was applied and a statistical software package utilized for analysing data. It was concluded that metallurgical short-circuits (hotspots) had the most significant effect on current efficiency. Bringing hotspots under statistical control resulted in a 5.40% improvement in current efficiency, which is equivalent to approximately 74 t of 99.999% pure grade A copper cathode production over a period of 1.5 months.

Jan 1, 2021

By Laurel E. Blackman

The DFI Project Information Management Systems (PIMS) Committee cooperated with the US Army Corps of Engineers (USACE) to develop a specification for PIMS used on USACE projects. Once completed the Committee developed a more generic version of this specification for general use, which is contained in this document. This first edition has simply removed the USACE-related requirements from the document. The committee will continue to work on this specification to enhance the content and also incorporate recent technological development for these systems. It is the Committee's intention that a second edition will be issued in 2022.

Jan 1, 2021

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

By R. B. King

This document was prepared by the DFI International Grouting Committee with the intent to provide a summary of main Standards and Guidelines available for the North America and Europe grouting industry. This document highlights the different approaches, methods and tools used internationally. The DFI International Grouting Committee comprises all parties involved on a grouting project: Owners, regulators, engineers, contractors, and manufacturers (equipment and materials). This document is not intended to cover every conceivable application or requirement of grouting. However, it does provide standard practice requirements for qualifications, materials, equipment, testing, and production procedures for the professional engineer to incorporate into their project specific requirements.

Jan 1, 2021

By K. Gharibi, A. Dehghani, S. Farrokhpay, M. Aghajanloo, M. Ostadrahimi

The effect of flotation operational parameters on froth stability and froth recovery was studied. Froth stability was measured using a special column. To determine the froth recovery, the froth height change model and froth height exponential model were used. It was found that since the interactions between the pulp and froth zones affect the time of froth formation, the exponential model is more suitable than the froth height change method for determining the froth recovery. The results showed that superficial air velocity and collector dosage have, respectively, the highest and lowest effect on the froth recovery, while froth recovery decreases sharply with increasing froth height.

Jan 1, 2021

By B. P. Watson, D. Hoffmann, D. P. Roberts

Potholes on the Merensky and UG2 reefs in the Bushveld Complex occur as near-circular to elliptical depressions or slumps on the reef horizon, normally presenting as severe disruptions which prevent economic extraction. Within the pothole, the reef and other strata may either be attenuated, absent, or highly deformed, this being the result of the overlying hangingwall strata having slumped down. The hypotheses for pothole formation involve several mechanisms, including downward erosion, upward fluid movement, or synmagmatic deformation. When potholes are exposed in mine workings, significant fracturing is often observed. This fracturing is particularly evident in anorthosite rock types. Stress measurements were conducted in a pothole on the Merensky Reef to determine if the fracturing was due to high stress conditions. The paper describes the measurement results and numerical modelling that was done to determine the influence of depth and mining on the stress condition at the site. The results show that high stresses do exist in at least some potholes, and that current formation theories do not adequately explain the measured stresses. In support of understanding the high local stress associated with the pothole, the study explored several rock engineering modelling processes to validate the conditions of the study site and enclosing excavations. A better understanding of the stress conditions in potholes with additional data could lead to more appropriate support design and avoidance of potential rockbursts in these structures.

Jan 1, 2021

By T. Nghipulile, M. Moys, M. Bwalya, H. Simonsen

The quest for efficiency in comminution is an ongoing concern as comminution usually constitutes a major cost component in the metal production industry. Such improvements can be made by circuit optimization or development of more efficient equipment. A novel crusher, known as the rotary offset crusher (ROC), promises to deliver in this space. The ROC was invented in 2002 by Michael Hunt, Henry Simonsen, and Ian Sinclair, but failed to garner enough support to progress to production. The original design concept was recently rekindled, and a laboratory version of the crusher has been built and commissioned at the University of the Witwatersrand. The crusher is simple in design, with two cylindrical discs that are parallel to each other, and, as the name implies, there is an offset between the vertical axes of the discs. The top disc has a conical section on its lower face, and this creates a crushing zone between the opposite faces of the two spinning discs. Centrifugal motion transports particles through the crushing zone. Batch experiments have been conducted with quartz at various crusher settings (discs offset, rotational speed, and vertical exit gap) for various feed size distributions. The indications so far suggest that the disc speed is a key factor affecting the performance. Size reduction ratios as high as 11 were recorded from experiments with quartz at a speed of 830 r/min.

Jan 1, 2021

By E. P. Preis, R. C. W. Webber-Youngman

The real cost of any mining incident has, empirically, proven to be estimation-driven, rather than factdriven. One of the main reasons for this lies with the complexity of the cost composition of any given mining incident. Incident costs comprise both direct and indirect cost factors, and in many cases the costs associated with these factors are incurred during different time periods following the incident. In this paper we aim to identify the various cost factors arising from mining incidents, provide a thorough understanding of all the potential cost factors identified, and draw general conclusions on the knowledge obtained. Furthermore, recommendations are made on how mining companies could use the results, in order to assist them in calculating the costs of mining incidents. The paper also provides suggestions for further research, with the emphasis on the most significant immeasurable cost factors, namely the costs of implementing job accommodations following an incident, the harm to company reputation, and the decreased productivity due to low worker morale/psychological factors following an incident. If mining companies are aware of and understand which factors could contribute to the cost of any given incident, future planning and incident cost estimations could be easier. It should, however, be noted that although this study provides a comprehensive list of cost factors (and detailed explanations), other unknown cost factors relating to mine incidents could prevail in extreme cases.

Jan 1, 2021

By M. Mpofu, B. Maphalala, S. Khan, S. Ngobese, D. Roberts

This paper details an assessment of stemming practices at a South African opencast coal mine and their influence on ground vibration and air blast. Quantitative and qualitative analysis methods were used for the study. The parameters assessed for the quantitative analyses included stemming length, stemming material type, blast-hole depth, burden, and spacing. Pre-blast data from the mine was analysed to determine the deviation between actual and mine design stemming parameters. Mine design stemming length was also compared to the rule-of-thumb stemming lengths. Peak particle velocity (ground vibration) and air blast data from seismograph stations around the mine was analysed to determine the correlation between stemming length and excessive ground vibration and air blast. The qualitative analysis involved observations of blasting procedures at the mine to determine compliance with mine procedures. Some level of non-compliance of actual stemming parameters to design stemming parameters was found, which initially suggested that non-compliance may have contributed to excessive air blast. However, further analysis of the seismograph results indicated no direct correlation between stemming length and excessive air blast and ground vibration. Since stemming parameters are interrelated, it is crucial that all blasting procedures, including stemming, are executed in accordance with best practice, and recorded accurately. There is a need for digital systems for capturing on-bench blasting parameters, as the currently used manual data recording and reporting systems are inefficient and prone to error. Improvements to blast designs are possible through efficient and accurate data recording and reporting systems.

Jan 1, 2021

By Juan Francisco y Medina, Antonio Nieto

La responsabilidad social empresarial (RSE) como estrategia para hacer frente al riesgo social existente y potencial se ve limitada por su incapacidad para cuantificar el riesgo. El índice desarrollado en este trabajo toma en cuenta factores cuantificables, tales como la competencia por el uso del agua, el suelo y la mano de obra, que permiten evaluar escenarios con riesgo de conflicto, e informarse sobre los componentes específicos a los que se debe dar prioridad para reducir el riesgo social. Los resultados del valor del índice se han comparado con casos sociales reales de ocho operaciones mineras auríferas diferentes de todas partes del mundo.

Dec 31, 2020

By Kash Sirinanda

Con un enfoque holístico, este artículo explora el concepto de minería sostenible del futuro. Orientado a motivar la reflexión de los líderes mineros, aborda aspectos y principios fundamentales en la industria —tecnologías emergentes, modelos de negocio, procesos de optimización, minería verde, esquemas colaborativos, etc.—, conducentes a un nuevo modelo operativo.

Dec 31, 2020

By Claudia Cooper

La autora desarrolla el importante papel que ha cumplido el sector minero peruano en la forja de un sólido entorno macroeconómico, que da sustento al incremento innegable en el estándar de vida de los peruanos y se constituye en base mínima para generar un mayor progreso. El arribo de grandes capitales mineros al Perú, no solo logró generar estabilidad cambiaria y de consumo en el país, sino también mantener cuentas fiscales sanas.

Dec 31, 2020

By Cristhian Vía

El artículo detalla una experiencia de implementación de microequipos trackless para el minado de vetas angostas, orientada a mantener anchos de minado económicamente factibles, rentables y seguros y a reducir significativamente la sobredilución. Se explica el diseño geomecánico para dimensionar aberturas y paneles, y se describe la estrategia de minado en cada operación unitaria tanto como los parámetros de control. Como resultado, se reportaron mejoras en todo el proceso de minado y se redujeron a cero de los accidentes por caída de rocas. Se perfeccionaron los indicadores de seguridad de la unidad, se redujo la sobredilución de 30 a 10%, y el costo de minado disminuyó de 34.17 $/Ton a 20.63 $/Ton.

Dec 31, 2020

By André Vela

Este trabajo técnico describe el desarrollo de un sistema de alineamiento láser en un equipo Raptor 55-2R de la marca Resemin —utilizado en minería subterránea— con el objetivo de mejorar la precisión y eficiencia de los procesos de voladura mediante el monitoreo de los grados de libertad del equipo de perforación. La solución encontrada aplica métodos algebraicos y un algoritmo de robótica (Denavit-Hartemberg) para describir la cinemática del brazo El estudio incluye pruebas de simulación.

Dec 31, 2020