Search Documents

By Virginia Lawson, Adam Price

The rougher flotation stage is used to reject liberated gangue at a coarse size. Base and precious metals due to their high specific gravity tend to recycle in the grinding circuit and report to the flotation circuit at a finer size than the gangue from which it is being separated. Generally liberation levels of greater than 50% are achieved in roughing and thus a portion of the feed can be immediately upgraded to final concentrate. The proportion increasing as the amount of liberated mineral in the feed increases. Scalping out concentrate from the rougher can reduce the size of the subsequent regrind and cleaner circuits. Examples of alternative process design for circuits demonstrates that you don’t need large volumes to effectively recover all of the minerals – you need smart flotation. Several case studies will be presented where circuits can be significantly reduced in size by designing smarter – not larger. This paper describes case studies to test the amenability of the Jameson Cell to produce final concentrate from rougher feed. Metallurgical performance and plant design implications are discussed. Froth flotation has been used extensively for mineral concentration for over 100 years. Although the flotation cell design has changed, it has generally simply increased in capacity rather than increase in efficiency. Cell capacities of over 600 m3 are now being used in rougher flotation particularly for the lower grade ores where the amount of surface area for flotation is deemed less significant than the required volume. The plant design volume in rougher flotation comes from laboratory batch flotation tests and/or pilot plants. The volume required for the plant is calculated based on the laboratory residence time multiplied by a scale- up factor. Examples of laboratory to plant scale-up design are given in Dunne et al. (2010 part 2). The factors are usually between 2 and 3. A laboratory residence time of 10 minutes would equate to a plant design residence time of 25 minutes using a 2.5 factor. The volume of the required flotation cells can then be calculated using the design tonnage and volumetric throughput. This scale-up factor takes into account the differences in performance between batch flotation efficiency and full scale plant. The differences are likely related to inefficiencies of bubble particle contact in large cells as well as froth recovery, which is essentially complete in a batch cell. Flotation cells, such as the Jameson Cells, are smarter designs that improve bubble/particle collection, bubble/pulp separation efficiency and operate with high froth recovery rather than simply getting bigger. The Jameson Cell was designed on the principal of improving the collection efficiency of fine particles by separating the contact zone from the separation zone and having the bubbles generated by the plunging jet shearing and entraining air. This means the method of bubble generation is not impacted by the wear of mechanical equipment as it the case in other flotation devices. Jameson Cells make bubbles less than 600 micron in size under most operating conditions (Ding, 2016).

Jan 1, 2019

By M. L. Harris, I. Zlochower, M. J. Sapko, I. E. Perera

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effective, rock dust must be able to disperse as individual particles to inert. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anti-caking additives after being exposed to moisture and then dried. The dusts were exposed to moisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anticaking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Laboratory (LLL), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for one day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for six months. This report details the analysis and characterization of anti-caking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber. INTRODUCTION In order for a coal dust explosion to propagate, five elements are required. In addition to the fire triangle in which three elements are necessary to sustain a fire—fuel (coal dust), heat (ignition source), and an oxidizer (oxygen in air)—a combustible dust explosion requires dispersion of a dust cloud (pressure wave) and confinement of a dust cloud (underground mine entry) (1). Coal dust explosions can originate anywhere in a mine. For example, when a small volume of a flammable methane and air mixture is ignited in a closed end, the high-temperature gases rapidly expand to create a pressure wave, sometimes referred to as a “pioneer wave,” that may steepen into a shock wave as it propagates away from the ignition source. The shock wave produces a wind that disperses the dust preferentially from any elevated and exposed surfaces (roof, ribs, belt structure, cribbing, etc.). Factors that are known to affect the intensity of an explosion are the dust particle size, the location of the dust within the entry, the dust dispersibility, and the volatility of the coal dust (1). Particles less than 75 μm (< 200 mesh) in size are most reactive (2). Dusts that are located on the roof, ribs, and elevated surfaces are more readily dispersed than dusts on the floor. Therefore, application of quality rock dust in sufficient quantities is essential to inert coal dust and to prevent continued flame propagation. 30 CFR 75.402 and 75.403 require 80% total incombustible content be maintained within 40 ft of the face, and 30 CFR 75.2 defines rock dust acceptable for use in underground coal mines. It also defined that “when rock dust is wetted and dried, will not form a cake”.

Jan 1, 2019

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

INTRODUCTION When Victoria became queen in 1837, that technical wonder of the 19th century—electricity— had progressed from being an exciting physical curiosity and was now a field of intense scientific investigation, invention and application. Its role in electrochemistry had been brilliantly quantified by Faraday in 1833–1834, and his earlier discoveries in electro-magnetism were to lay the foundations of electricity generation and the electric motor. In this age of electrical experiment, silver electro-plating emerged as a popular decorative art, at first using batteries to provide the deposition current, superseded by dynamos in the early 1840s. The decorative chemical and electroplating of precious metals was largely pioneered in England by the firm of G.R. Elkington and Co., founded in Birmingham by George Richards Elkington (1801–1865) in 1832, and protected by a series of patents which helped the company establish a leading position in the new field of ‘electrometallurgy’. In the same decade, the technique of electrotyping emerged, the first application of electro- forming by electrolytic deposition. Simultaneously invented by Spenser in England and Jakobi in Russia, but generally claimed for Jakobi, electrotyping involved plating a thick copper layer on to an electrically conducting mould wall embossed or incised with a pattern or profile which would consequently be replicated on the copper deposit—essentially a method of casting by electro-deposition with the mould wall as cathode. Woolrich’s invention of the low voltage magneto-dynamo in 1842 eliminated the need for batteries as a continuous source of deposition power, opening up the possibility of making more massive electroplated deposits, and by the mid-point of Victoria’s reign in 1869, the work of Wilde, Wheatstone and Siemens had produced the self-excited electro-dynamo, capable of higher voltages and yet greater deposition power. In this early Victorian period copper was extracted and refined by methods which had developed step-by-step over many decades. Only relatively rich copper ores containing more than, say, 6% Cu were economically useful, and the final copper product was far from pure. Copper production in Britain was located principally in the Swansea area of South Wales, based upon the ‘Welsh process’ of reverberatory batch smelting and refining, using locally mined coal and ore imported from Cornwall and elsewhere. Silver was an important by-product. Much of the output was exported and South Wales remained a principal supplier to the world copper market until the 1890s. It was here at Pembrey, a few miles west of Llanelli, that a new primary copper smelter was stablished in 1849 under the name Mason and Elkington, arguably to supply the Elkington company’s market for electrotype products.

Jan 1, 2019

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019

By Phil Jones, Ben Johnson

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations:

Jan 1, 2019

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By A. Gupta, F. Hrach, L. R. Mendoza, K. Flynn

ST Equipment & Technology LLC (STET) has developed a novel processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an energy-efficient and entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles >75μm in size, the STET triboelectric belt separator is suited for separation of very fine (<1μm) to moderately coarse (500μm) particles, with very high throughput. The STET tribo-electrostatic technology has been used to process and commercially separate a wide range of industrial minerals and other dry granular powders. Here, bench-scale results are presented on the beneficiation of low-grade Fe ore fines using STET belt separation process. Bench-scale testing demonstrated the capability of the STET technology to simultaneously recover Fe and reject 2 from itabirite ore with a D50 of 60μm and ultrafine Fe ore tailings with a D50 of 20μm.The STET technology is presented as an alternative to beneficiate Fe ore fines that could not be successfully treated via traditional flowsheet circuits due to their granulometry and mineralogy. INTRODUCTION Iron ore is the fourth most common element in earth’s crust [1]. Iron is essential to steel manufacturing and therefore an essential material for global economic development [1-2]. Iron is also widely used in construction and the manufacturing of vehicles [3]. Most of iron ore resources are composed of metamorphosed banded iron formations (BIF) in which iron is commonly found in the form of oxides, hydroxides and to a lesser extent carbonates [4-5]. A particular type of iron formations with higher carbonate contents are dolomitic itabirites which are a product of the dolomitization and metamorphism of BIF deposits [6]. The largest iron ore deposits in the world can be found in Australia, China, Canada, Ukraine, India and Brazil [5]. The chemical composition of iron ores has an apparent wide range in chemical composition especially for Fe content and associated gangue minerals [1]. Major iron minerals associated with most of the iron ores are hematite, goethite, limonite and magnetite [1,5]. The main contaminants in iron ores are 2 and Al2O3 [1,5,7]. The typical silica and alumina bearing minerals present in iron ores are quartz, kaolinite, gibbsite, diaspore and corundum. Of these it is often observed that quartz is the mean silica bearing mineral and kaolinite and gibbsite are the two-main alumina bearing minerals [7]. Iron ore extraction is mainly performed through open pit mining operations, resulting in significant tailings generation [2]. The iron ore production system usually involves three stages: mining, processing and pelletizing activities. Of these, processing ensures that an adequate iron grade and chemistry is achieved prior to the pelletizing stage. Processing includes crushing, classification, milling and concentration aiming at increasing the iron content while reducing the amount of gangue minerals [1-2]. Each mineral deposit has its own unique characteristics with respect to iron and gangue bearing minerals, and therefore it requires a different concentration technique [7].

Jan 1, 2019

By P. Latostenmaa, T. Veneranta, J. Järvi, E. J. Peuraniemi

Boliden Harjavalta has operated a copper flash smelter since 1949 thus the smelter celebrates 70th anniversary of flash smelting in 2019. This paper shortly describes the historical perspective of the smelter and gives an update of the current operational issues and process modifications made during the recent years. The plant has carried out several major investments lately providing a firm view on the future. A new landfill area for the final slag was commissioned in 2018. A modernization of the concentrate storage area, a new acid plant and a debottlenecking project of the smelting line have been recently commissioned. At the same time, the tankhouse capacity will be expanded. This paper focuses on smelter modernizations. INTRODUCTION Boliden is a metal company operating mainly in northern Europe with core competencies in the fields of exploration, mining, smelting and metal recycling. Boliden Harjavalta, located in Finland, is part of the Smelters Business area of the Boliden Group and operates a copper and nickel smelter with related sulphuric acid plant in Harjavalta, and a copper refinery in Pori. As a short historical review, Harjavalta’s history may be dated back to the year 1910 when the Outokumpu ore body in eastern Finland was discovered. By the end of 1913, a copper mine was in operation and a copper plant based on Hybinette process was ready for commissioning. Due to difficulties in metal recoveries and throughput the Hybinette process was permanently shut down in 1929, and 100% of the mining production was sold as concentrate abroad. As the mine production increased steadily, a decision of a new smelter was made in early 30’s. In 1936 Outokumpu’s copper smelter based on electric smelting was commissioned in Imatra. The smelter was dismantled and transferred to Harjavalta during the final stages of the Second World War. The copper refinery started in Pori already in 1941 and the first copper anodes were cast in Harjavalta in 1945. First sulphuric acid plant started operation in 1947. Due to the post-war shortage of electrical energy, the plant metallurgists initiated a major development work to start exploiting the latent heat of concentrates. Thus, the flash smelting method was developed in Harjavalta and commissioned in 1949. Ten years later, flash smelting was also applied for nickel concentrates. Table 1 summarizes major historical and technical milestones of Harjavalta. The history of flash smelting is described in details in another paper of this conference (Jåfs et al., 2019).

Jan 1, 2019

By S. Bantubani, I. Mc Dougall, S. Arjun, H. Joubert, R. Hansraj

The requirements determining the design of the Söderberg electrode columns used in base metal applications are different to those of other industries. There is a strong trend to position the contact shoes above the furnace roof in order to reduce the risk of water leakages directly onto the furnace bath. Tenova Pyromet has adapted its proven electrode column design for application on base metal electric furnaces based on these requirements. The design modifications implemented as well as considerations regarding the overall electrode-roof-furnace arrangement are discussed. Equally important is the management of the Söderberg electrodes to prevent over or under baking. Tenova Pyromet has developed the AutoFurn™ furnace controller to not only optimise furnace operations, but to improve electrode management. An overview of the electrode management control philosophy implemented by AutoFurn™ is provided, focusing on intelligent electrode regulation, slipping and baking. INTRODUCTION Tenova Pyromet has developed an electrode system for use in base metal furnaces, which builds on the experience that Tenova has gained during the past 30 years with electrodes in the ferroalloy and base metals industries. In base metals applications, an important safety consideration is the minimization of water within the furnace and on the furnace roof. In addition, direct contact between copper equipment such as contact shoes and pressure rings and the contents of the furnace is discouraged. In a 3 phase AC furnace, three electrode columns transfer the electrical energy to the furnace bath. Both Söderberg and prebaked carbon or UHP graphite electrodes are in use in base metal furnaces. In each column, the electrode is held in position by a hydraulic slipping and regulating device, a pressure ring and contact shoes. The electrodes can operate in a submerged-arc or brush-arc configuration, where the electrode is immersed in the slag or a short distance above the slag (Mc Dougall 2013). The electrode equipment is divided into an upper and a lower electrode assembly. The self-baking Söderberg electrode is made from lengths of steel casings that are added to the top of the electrode column and welded into place. Carbon electrode paste is added to the inside of these casings and is baked to form a solid tip in the region of the contact shoes. The working platform that surrounds the area where new electrode casings are added, is electrically isolated from the building and each electrode is isolated from the others to ensure the safety of the personnel who perform the electrode casing additions.

Jan 1, 2019

By F. Dehghani, B. Rezaie, T. Ghosh, A. Sachan

Comminution is an integral part of the mineral extraction process. However, the influence of the comminution method (ball and rod mills) on silica and magnetite particle shapes has not been substantially investigated. Shape parameters for fractions of -250+212, -150+125, and -106+75 μm sizes were examined utilizing a scanning electron microscope and a Clemex vision PE image analysis system. The silica particles displayed higher elongation and flatness parameter values for rod mill products, but roundness and relative width parameter values of rod mill products are less than that of the ball mill products. Magnetite particle elongation and flatness parameter values of ball mill products in fraction sizes of -250+212 and -106+75 μm are larger than rod mill products, but roundness and relative width parameter values of ball mill products are smaller than rod-mill products, but for the -150+125 μm size range the result is converse. Furthermore, particle elongation and flatness increased with decreasing particle sizes of silica, whereas, roundness and relative width decreased for both Ball and Rod Mills. In case of magnetite, ball mill products displayed an increase of flatness and particle elongations with decreasing particle sizes but flatness increased and roundness and relative width decreased. Similarly for rod mills, magnetite fractions of -150+125 μm were found to have the largest values of elongation and flatness. INTRODUCTION Comminution alters the size and shape, causes lattice distortion, changes chemical composition, surface area, surface-free energy, and polymorphic transformation of all materials. The quantity and quality of such changes depend on specifications of the material feedstock, the type of mill being utilized, the specific energy input, ambient temperature, and environmental pressure [1]. The shape difference between the milled products depends on different grinding mechanisms and the respective breakage principles that these mechanisms depend on [2, 3]. With decreasing particle sizes, the nature of the particle surface become crucial [1]. The influence of the breakage technique has been found to be non-trivial and heavily dependent on the type of grinding mill used for particle size reduction [4]. Shape is an important industrial parameter for predicting particle behavior in downstream processes. The shape parameter affects the way particles burn, compact, are recovered, flow in fluids, sinter, float, agglomerate, fluidize, interact with pulmonary tissue, cut, abrade, react with chemicals, form structural materials, and retain and permit fluids to flow [5, 6]. The distribution of particle sizes and shapes are important for mining, civil and chemical, pharmaceutical, and various other industries with interest in the population modeling of atmospheric dusts, smoke, and grit [1, 3, 6]. The shape parameter not only affects the chemical, physical, surface properties of particles but is also important for downstream processes [5, 6]. Image analysis has been found to provide detailed information about size and shape of the particles and can be used for the control of product quality [4].

Jan 1, 2019

Real time analysis of ore quality between the mine and mill provides major benefits to copper mining and processing operations. Prompt gamma neutron activation analysis (PGNAA) is a proven technique that has been successfully applied for real time conveyed flow multi-elemental measurement. The advantage of PGNAA is that it measures through the full conveyed cross section continuously and provides representative element measurement without the need to constantly sample coarse (primary crushed) conveyed flows. High specification PGNAA analyzers enable accurate measurement over time increments as short as thirty seconds. Elements such as copper can be measured to a precision of 0.02% copper which is sufficient for high confidence in decisions for bulk flow diversion. Increments of eight tonnes are being diverted through a bulk ore sorting application to remove batches of waste from mill feed as well as divert material to different stockpiles based on ore quality. Longer measurement increments of two to five minutes are suitable for blending control of ores to reduce feed quality variability and to control average ore quality within a target range. Feed blends can be adjusted as frequently as required but typically multiple measurement increments are composited to produce a rolling average ore quality. The paper details two case studies where analyzers have been successfully used to measure conveyed flows for blending and bulk diversion applications. The real time measurements of ore composition are also used for ore reconciliation, in metal accounting and providing process operators with advance warning of ore quality changes that may affect grinding performance and cause process upsets. Real time ore quality measurement has proven beneficial in improving copper processing performance through better utilising plant capacity in a leaching operation, optimising ore feed quality, and reducing unnecessary processing of waste. INTRODUCTION Representative real time elemental analysis of conveyed ore quality using fully penetrative technologies has been available to the minerals industry since the 1990s. The Prompt Gamma Neutron Activation Analysis (PGNAA) technique was developed into a conveyed material analyser and soon adopted by the cement and coal industries which recognised the benefits in real time quality management. These commodities were ideally suited to this measurement technique as operations generally involved conveying bulk material prior to processing. Measured quality was used to divert material to different destinations or used to control blending for improved quality consistency. Uptake in the minerals industry, however, has been slow until the last ten years, and particularly until the mid-2010s.

Jan 1, 2019

By F. F. Roberto

Sulfuric acid has been demonstrated to be an efficient lixiviant for in situ extraction of copper in the past. It has also been proposed that microbial production (by iron-oxidizing acidophilic bacteria) of acidic ferric solution either in situ or ex situ could provide an economic strategy to generate an effective lixiviant for secondary copper sulfides like chalcocite and covellite. Copper heap bioleaching also takes advantage of this approach. One of the major environmental challenges for in situ copper recovery projects is the containment of acidic solution within the ore deposit, and ultimate restoration of the depleted ore body to its original state. A perhaps overlooked aspect of projected site operations is the possibility that transient acidic conditions and pumping of solutions from surface reservoirs into the subsurface could stimulate the growth of iron- or sulfur-oxidizing species of acidophilic microbes in the ore body, leading to additional generation of sulfate, acid, and ferric iron. This outcome would benefit extraction of copper in mixed oxide/sulfide deposits in the near term, but could complicate restoration activities. Possible impacts of pumping acidic solutions into the subsurface on microbes resident in, or introduced into the extraction zone will be discussed in the context of our understanding of copper heap bioleaching and acid rock drainage. INTRODUCTION As high-grade deposits of metals such as copper continue to decline, conventional mining methods have evolved to mine and process larger and larger quantities of ore. What is currently defined as ore today often contains less metal than the tailings of past operations. The throughput of current-day mines also leads to tremendous amounts of waste rock and tailings that may threaten the environment and communities around the mines, as has recently been experienced by 3 major tailings disposal facility (TSF) dam failures in the past 5 years. Community acceptance of large mine operations thus becomes more difficult to achieve—loss of the social license to operate. In response, the mining industry urgently pursues innovations that can fundamentally change the way in which metals are mined. In situ recovery (ISR) of metals represents one approach to a more sustainable mining industry, by virtually eliminating the need for a pit or underground excavation, eliminating the excavation and transportation of ore to a process plant and the ensuing noise and dust that is generated, and any need for waste rock dumps or TSFs. An ISR mine could have very little visible footprint beyond a network of wells, pumps, and piping to transport pregnant solution to a recovery facility, such as a solvent extraction- electrowinning (SX-EW) plant for copper. Some solid waste streams and/or storage ponds may still be necessary to treat and store bleed streams, PLS and raffinate, or as part of groundwater restoration activities. Thus capital and operating investments would be potentially much lower than that required for a conventional mine. In theory production could also be controlled to adjust to subsurface ore grade and match market demand. A not insignificant challenge of in situ recovery is the requirement for an efficient, low-toxicity, and ideally selective lixiviant for the metal that is targeted.

Jan 1, 2019

By Arnfinn Prugger

"The construction of the new Scissors Creek shaft at the Rocanville mine, the first potash shaft successfully completed in Saskatchewan Canada since 1979, is summarized here. Located 15km from the existing Rocanville surface plant, this new 6 m inside-diameter, 1121 m deep service shaft was built for fresh-air ventilation and access. Shaft construction in the Saskatchewan sedimentary basin involves sinking through five different rock-types: glacial tills, shales, sandstones, carbonates and salts. The first four rock- types are all water-bearing, and the salts will dissolve in water. This results in five different sinking challenges and requires five different shaft lining designs. The upper 580 m of rock (the till – shale – sands sequence) was frozen before sinking, and grouting methods were used for water control through deeper carbonate levels. Challenges that were faced and overcome during shaft sinking are reviewed, and ideas that future operators working in sedimentary basin environments might consider in order to avoid these difficulties are discussed.INTRODUCTIONThe Nutrien Inc. (formerly Potash Corporation of Saskatchewan Inc. / PotashCorp) Rocanville potash mine in southeast Saskatchewan, Canada has been in continuous production since 1971. Devonian potash, formed approximately 380 Mybp, is mined in a sedimentary basin environment at approximately 1000 m depth below surface in this area of Saskatchewan. The predominant use for finished potash products is fertilizer: potash fertilizer is concentrated and nearly pure KCl (i.e. greater than 95% pure KCl). Currently 10 potash mines are in operation in Canada, all in Saskatchewan. In 2018 Saskatchewan mines produced ˜ 23 million tonnes of finished potash products, which is approximately 35% of World demand of ˜ 66 million tonnes for the year (e.g. Nutrien Inc., 2019).In November, 2007 it was announced that the Rocanville potash mine would be expanded to increase production from 3.0 Million tonnes per year (Mtpy) to approximately 6.0 Mtpy of finished potash products, requiring an increase in hoisting capability from approximately 9.0 Mtpy to over 18.0 Mtpy. The Rocanville potash mine has historically been accessed through two shafts: a production and ventilation exhaust shaft, and a service and ventilation fresh-air shaft located approximately 200 m from each other. All surface offices, processing facilities, etc. are situated near these original shafts.A very important part of the recent Rocanville expansion involved the construction of a new service shaft (6 m diameter, 1121 m deep) for fresh-air ventilation and access, approximately 15km west of the existing surface plant. Once this third shaft was completed in 2015, the historical service shaft was converted to a second exhaust and production shaft. Three shafts are now available for mine access, ventilation and ore hoisting at Rocanville. As of December 31, 2017, annual nameplate capacity for Rocanville was 6.5 million"

Jan 1, 2019

By R. K. Jonas

Many leading copper and other mineral processors have rapidly adopted advanced controls in last 5-10 years. Almost 600 multivariable predictive controls have been installed in mineral processing, and almost 50% of those are in copper concentrator plants. In most cases, mineral processors rely on 3rd party support to implement these advanced technologies. One challenge facing advanced control user is the selection providers and services for these technologies. The trend has been towards the use of multivariable predictive control and use of technology provider’s services. This paper will discuss status of advanced control, and the merging trends in the mining industry. A review will be presented of how advanced control is being applied in the mining industry over the last decade, and how user challenges are being overcome. Next the emerging uses of multivariable predictive control (such as multi/inter-unit optimization), focusing on the latest trends in concentrator plants. Finally, a review will be made of emerging technology advances in the that can be advantageous to mineral processors. INTRODUCTION Review of advanced control in mineral processing Advanced controls are serving an increasing role to improve processing plant operations and profitability. As advanced control is being installed into more mining processing plants such as copper concentrators, many of these plants are concerned about the selection technologies and vendors to support the installation and maintenance of these controls. In a study by Jonas and Craw (2011), they found that most new users have not had prior experience with advanced controls. It is the author’s experience of almost 30 years in advanced controls that most mineral processers considering advanced controls can benefit from better understanding of the technologies and their support requirements.

Jan 1, 2019

By B. D. H. Knights, N. B. du Preez

The recovery of the economy of the Democratic Republic of Congo has allowed for the rapid increase in production of copper from this region, while the increased price of cobalt continues to support the recovery of that country’s economy. This has enabled the modernization of the process technology used, particularly the change from direct electrowinning of copper to solvent extraction-electrowinning. With this change has come a variety of technical challenges in optimizing the recovery of cobalt from these sources. In this paper, we discuss aspects of the flowsheets for the production of cobalt from the ores of the DRC and Zambia, highlighting the technological improvements that have been made. Following this description of the practice, we assess the challenges of further improving the recovery and purity of cobalt from these sources. INTRODUCTION The African Copperbelt (Figure 1) is by far the biggest producer and holds the greatest reserves of cobalt (Sheed, 2015). However, the ores of this great mining region are extracted primarily for their copper content, and cobalt is a by-product. The ratio of copper-to-cobalt is between 6 and 20 to 1, with the ores from the DRC richer in cobalt than those from Zambia. The overall supply of cobalt, shown in Figure 2, is increasing due to an increase in demand for its use as a battery material. Cobalt is used in superalloys, hard metals, pigments, catalysts magnets, tyre adhesives, lithium-ion rechargeable batteries, and wear-resistant coatings, amongst others. Although these generic categories persist, Figure 3 shows how the relative usage of cobalt is changing due to the uptake of electric vehicles in China and Europe. Cobalt is a key element in lithium-ion batteries, and because it is widely anticipated that electric vehicles will be legislatively encouraged, it is anticipated that the demand for cobalt will rise. This anticipated increase in demand resulted in an increase in the price for cobalt, to which suppliers responded over-eagerly, and the price has dropped dramatically in the first few months of 2019, as shown in Figure 4. However, there is a clear cycle of price peaks in cobalt’s history.

Jan 1, 2019

By Ling Wu

The development of pyrometallurgical technologies has been focused on new smelting reactors, but the proposal for new converting reactors has been substantially lower. Up to today about 80% of copper matte is treated by the traditional P-S converters which have the weakness of pollutant fugitive emissions. Therefore, the continuously converting processes for treating molten matte have been studied and developed. In July 2017 the "oxygen-rich side blowing smelting + multi-lances top converting & fire refining" continuous copper treating process was commissioned. This process was designed by ENFI and YanTai GuoRun Copper Smelter. In this process, oxygen rich side blow technology is adopted for smelting, which is a new type of side blowing smelting furnace to produce high-grade copper matte. The converting adopts the horizontal multi-lances top-blowing continuously converting process, which eliminates the transportation of molten melt and the SO2 fugitive emission. The intermediate products of this process, copper matte and blister copper is fed into the furnaces respectively through launders. This new process is more advanced, more reliable and more environmentally friendly. Until now, this process in the GuoRun copper smelter is operating smoothly. An increasing number of projects which use this process are under design and construction in China. INTRODUCTION At present, there are many advanced smelting technologies for copper concentrate, such as oxygen bottom blowing smelting, flash smelting, top lance smelting (including ISA and Ausmelt furnaces smelting), side blowing smelting, Mitsubishi smelting, etc. At the same time, there are many copper matte converting technologies such as oxygen bottom blowing continuous converting, flash converting, Ausmelt top lance converting, horizontal multi-lances top blowing converting, Mitsubishi converting, P-S converter converting, etc. The final blister copper fire refining technology mostly adopts rotary anode furnace. Therefore, in the process of processing and extracting the copper from concentrate to produce anodes, there are dozens of technology combinations. Among them, the non-continuous converting technologies for molten or cold matte are often adopted in the converting process. The traditional P-S converting technology had been utilized for over one hundred years, with a mature, reliable and simple operation, also has advantages in the secondary scrap smelting of a wide range of quality. However, due to its batch operation, frequent roll in and out, poor sealing, considerable air infiltration, needs for ladles for molten phases transportation and other characteristics, the technology has a serious pollution problem due to fugitive SO2. At the same time, in the cold matte converting technology, the molten matte needs to be cooled and then processed. The sensible heat of the molten matte cannot be recovered, and the preparation process is needed in the process. Therefore, both energy consumption and investment are relatively higher.

Jan 1, 2019

By M. Javier

Mining is most vital to our civilization. The current model of extraction technologies was designed without an expiration date and therefore generates environmental effects that are severe. Mining results-effects have been traditionally accepted and promoted around the world since Agricola described mining. Mining’s extractive technology is outmoded and standardized and inflicts negative results-effects on nature. Those results are liabilities dimensioned in legacy and type of nature able to provide to the next generation. In order to design, build, and transform mining effectively we must ask: What is the vision of mining? Mining has exhausted its antiquated mindset of over 200 years. Now it merely pilots us into crisis. The challenge today is to resolve the socio-environmental conflicts globally with a radical transformation of the mining business at its core. This paper illustrates that old mindsets must be radically updated or the concept of mining will continue to be trapped. Changing the mindset will enable discourse toward a new destiny. These changes will change mining for the better. We are able to evolve and get different results than in the past by pursuing a new legacy to live in harmony with nature for many more years. INTRODUCTION Minerals are supported by the law of conservation of mass. They have the unique characteristics of being finite, exhaustible, unsustainable, and have an unlimited recycling. Minerals are also hard to find because we have explored and virtually exhausted the whole crust of this planet. Orebodies that used to be considered world class are almost exhausted. In the short-term, it would be almost impossible to find new world class orebodies unless they could be extracted from the ocean, the moon or other planets like Mars. Mining is designed to extract minerals for profit and to keep civilizations functioning. Subsequently, mining has a social issue that is an economic issue. Thus, mining must be seen as a real and urgent subject matter that must be protected in thought and in fact. The actual mining extractive technologies produce disequilibrium in nature that has unknowable effects in the course of time. History is filled with the negative consequences to nature due to the model of mining. The evidence of these effects from mining’s model is apparent in repetitive liabilities around the world. The effects negatively impact nature without any consideration to how these impacts will manifest themselves in the future. This model of mining is widespread and extolled in every corner of the planet because it is old and familiar and although wasteful and outdated, we do not want to expend financial resources from profit or elsewhere to explore newer ideas, methods, or technologies that would help us keep a sustainable harmony between extraction and nature. We need a new vision for mining today and to explore in what way academia can and must play a social role in the teaching of mining methods. We need to question why we continue to support the old model of mining and to ask ourselves what prevents us from updating and modernizing the method of mining to meet the current needs not just of civilization but the urgent needs to undo some of the damage to the earth. This paper hopes to develop a method to change our minds about how we conduct the business of mining in order to control the destiny of it.

Jan 1, 2019

By Euler De Souza, J. Daniel Stinnette, Julian Varaschin

"This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and of electric equipment and examines how they can be applied in determining reasonable ventilation rates for Tier IV compliant diesel equipment and for electric equipment operating in mining environments. Airflow calculations for modern diesel-powered equipment and for electric equipment are more complex and must be based on a combination of factors that are unique to each mine. Methodologies for ventilation rate determinations for each case are proposed in this paper.INTRODUCTIONTraditionally, airflow requirements for production and support equipment operating in underground mines have been determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations or determined empirically from known quantities. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is still a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. The question remains, what ventilation rates should the ventilation system designer apply for modern diesel equipment?Also, given the ongoing development of grid/battery-electric equipment and active construction of fully electric mines, it has become critical to determine adequate airflow rates per brake kilowatt of electric engine power. One of the most important criteria for determining ventilation rates for electric equipment is the amount of heat they generate, as this is the most significant emission produced by electric equipment (which do not produce exhaust gases or particulates). Therefore, ventilation rates required to dissipate heat from electric equipment must be suitably determined for all electric vehicle fleets operating in underground mines."

Jan 1, 2019

By Joerg Hammerschmidt, Marcus Runkel, Steffen Haus

Given the limited number of new plant construction, focus is turning to the optimization of existing metallurgical roasting plants. To meet the goals of high process efficiency with limited capital expenditure, plant owners are looking for new strategies, including digitization and expert support. As a supplier for numerous roasting, gas cleaning and sulfuric acid plants, Outotec has intensified its effort in recent years to develop solutions to accommodate increasing customer need. This article presents a short review on how Outotec is applying advanced control tools for the fluidized bed industry. Focus will be given on how to transfer the existing technology (used in selected Zinc roasting plants for over a year now) to copper roasting. Outotec has developed the Pretium Roaster Optimizer, a system based on heat and mass-balanced simulation models. Direct experience with this technology will be shared and will highlight similarities to the Partial and Sulfate Copper roasting processes. Pretium detects equipment and plant bottlenecks and provides consistency in process development. The Pretium program combines 24/7 advanced online digitalization tools, along with expert personal support when required. INTRODUCTION Fluidized bed reactors have been used for commercial-scale zinc and copper roasting since the 1950s. While the principles of roasting remain unchanged, over time, the technology has advanced to improve process control of roasting plants. In the past, environmental and safety standards were the driving forces for improvement of equipment and plant design. Today, the emphasis is on plant efficiency and optimization. Another change has come in process control philosophy. While plant control and operation have traditionally been the responsibility of owner/operators, they have now shifted to include both integrated digital tools and specific know-how from engineering companies. This can be seen from the earliest design stages through commissioning and into production, as evidenced by zinc roasting plants in Mexico, Brazil and Turkey.

Jan 1, 2019

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019