Search Documents

By G. G. Li

"A dynamic ventilation-modeling package, VREX, was used to simulate the mine activities through tracking the equipment movements in underground workings and determine the airflow demand for a new production scenario in a ventilation-on-demand (VOD) system. It incorporates the mine development data from a discrete event simulation and balances the ventilation network using the CANVENT ventilation solver. A case study was performed to demonstrate the capabilities of the software, evaluate the performance of the network and determine the potential energy savings for implementing VOD in a deep mine operation.INTRODUCTIONThe ventilation cost of an underground mine can be significant—up to 50% of the mine’s energy consumption could be used to run fans and provide heat/refrigeration to meet the specified production environment for workers and equipment. The VOD system has proven to be more efficient in operating the fans and supplying the amount of air corresponding to the mine activities taking place in underground workings (Hardcastle, Kocsis, & O’Connor, 2006). In order to properly solve and evaluate the VOD system, a dynamic ventilation modeling software VREX—the ventilation rules engine has been developed to simulate the mine activities and determine the airflow demand for each production scenario within an operation period (Dasys & Cameron, 2011).VREX is a decision support tool, backed by the CANVENT mine ventilation solver (Li, Kocsis, & Hardcastle, 2009), for determining the outcomes of network configuration changes over time. The software incorporates the mine development data with ventilation modeling through the discrete event simulation (DES) performed by SimMineTM. As it simulates the air requirements for different vehicles and activities, VREX can evaluate both the performance of the ventilation system and the potential economic benefits of making operational or technological changes (Pritchard, 2010). For example, the model can be used to assess the economic and environmental impacts arising from modifying regulations to support the use of electric or lower emission vehicles. The combination of DES and ventilation modeling provides a new technology to generate the production scenarios according to mine schedules and activities and to determine the potential benefits for various levels of ventilation control, such as time interval and work shift change."

Jan 1, 2019

By F. A. Auld

"Traditionally deep shaft sinking from the ground surface was carried out using drill and blast methods. Although large diameter blind shaft drilling has been carried out successfully on numerous occasions previously, including as early as 1852 in Germany (Auld, 1995), little attempt has been made until more recently to mechanise the shaft sinking excavation process using down-the-hole machines. This paper reviews the development of deep shaft sinking machines from the early 1970’s up to the present day. INTRODUCTION Mechanical excavation methods can significantly improve excavation performance, in order to access natural resources faster, and labour safety is increased compared to drill and blast operations. However, shaft sinking machines need to be capable of accommodating all the basic requirements for deep shaft sinking, namely: 1. Excavation and muck removal 2. Ground stability control 3. Groundwater ingress control 4. Temporary lining installation 5. Permanent lining installation and watertight sealing 6. Ventilation 7. Secondary means of egress for personnel In addition, how the machine operates in the shaft is an important factor, either slung on ropes from a surface headgear or on its own in the bottom of the shaft. An all-embracing machine which can deal with all of the above conditions is impossible but many of these requirements can be incorporated into a single machine. Deep shaft sinking also differs greatly from normal tunnel construction which employs the use of either a roadheader arm installed within a shield or a full-face tunnelling machine for excavation. Hydrostatic pressure and ground stability problems increase with depth, whereas in tunnelling the depth is normally relatively shallow and the aforementioned factors remain approximately constant along the tunnel length. DEEP SHAFT SINKING MACHINES All the shaft sinking carried out previously in the UK was by the traditional method of drill and blast. Elsewhere, in other parts of the world, attempts have been made to mechanise the process."

Jan 1, 2019

By T. Hidayat, D. Shishin, V. Prostakova, M. Shevchenko

The chemical compositions of copper feed streams are becoming increasingly complex following the growing demand for metals and corresponding shortages of primary sources. The optimisation of process conditions requires an accurate description of phase equilibria and thermodynamics. Integrated experimental and thermodynamic modelling research program on the characterisation of the complex, multi-component, multi-phase gas-slag-matte-speiss-metal-solids Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Ni-Sb-Sn-Ag-Au) system is being carried out to support companies undertaking the pyrometallurgical primary production and recycling of copper. The experiments involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of equilibrium phase compositions with quantitative microanalytical techniques, including electron probe X- ray microanalysis and Laser Ablation ICP-MS. The thermodynamic modelling is undertaken using FactSage computer package with advanced thermodynamic solution models. The continuing development of research methodologies has resulted in significant advances in research outcomes. Implementation of the results of these fundamental studies involves an ongoing collaboration of researchers and industry technologists. An overview of recent progress in research, implementation and applications in industrial practice are given in the paper. INTRODUCTION Rapidly developing technologies increase the demand for various metals in number and volumes. Modern technological devices such as mobile phones, computers, other electronic devices, have dozens of metals—all those metals have to be a) produced and b) recycled. The fast transition in mobility from fossil energy delivered through combustion to renewable energy first stored in bakeries and delivered through electric engines introduce a significant change in the metal demand in terms of both type and volume of metals. Pyrometallurgy is playing a key role in supporting these changes in our industrialised society.

Jan 1, 2019

By W. Dziurzynski, St. Wasilewski, T. Palka, A. Krach

"Air parameter monitoring systems, regardless of gasometrical protections, provide a significant number of measurement data. The obtained data broadens the knowledge on processes taking place in underground workings and shows the relationships and influence of machines and technological processes on the variability of ventilation parameters in the areas of longwalls. Nowadays, computer simulation methods are increasingly used to reproduce the flow of air and methane mixture in the area of longwalls equipped with shearers. The paper presents the results of a research experiment covering a long-term observation of a longwall area during mining with a shearer using sensors from the mine's monitoring system. Data from sensors for methane concentration, pressure and velocity were used and additional ventilation measurements were taken to determine the parameters characterising the air flow in the area. The influence of different machine cycles in the longwall on the changes of air parameters in the area of the longwall was shown. A numerical model of the ventilation area was developed and the computer program VentZroby was used for the calculations, which allows for the simulation of the process of ventilating the area of the active longwall during the extraction of coal with the use of a shearer and haulage of the run-of-mine. Computer simulation of the influence of the shearer's operation and the methane inflow associated with the distribution of the mixture of air and methane was carried out. The results of the simulation were compared with the data recorded by the monitoring system’s sensors during the measurement experiment. Comparison of the recorded methane concentration courses with the results of a computer simulation of the air and methane flow conditions in the mining area showed changes in the gassiness. INTRODUCTION Studies carried out in the Polish and global mining industry show that methane is an obvious factor in limiting mining production due to the loss of continuity in the operation of longwall complexes in hard coal mines under methane emission hazard (Schatzel et al., 2008). In addition, methane hazards have a significant impact on the safety of the operators of machinery in the longwall. The requirements of Polish regulations and the practice of safe operation of mining longwalls require correct determination of gas concentration, volume flow, as well as pressure and temperature of the flowing air. As part of the research undertaken in the Budryk (Wasilewski, 2010) and Bielszowice (Dziurzynski et al., 2009) mines to assess the methane hazard in the longwalls and workings in the vicinity of the longwall, research experiments were carried out, during which air parameters were recorded by the mine monitoring system and additional testing equipment in different cycles of shearer operation."

Jan 1, 2019

By Bradford C. Wesstrom, Ricardo Parra

The Freeport McMoRan El Paso Refinery uses co-generation to produce some of its electricity and all of its steam. This paper will cover the operation of the co-generation plant natural gas turbine at a fixed RPM for blade longevity and energy output. The by-product heat from the turbine passes through boilers with additional heat from a duct burner to produce steam for the Tank House and auxiliary operations. The steam demand varies dramatically throughout the day based on unloading activities in the Tank House. The use of an automated steam control system within the El Paso Refinery will help stabilize line pressure by incrementally controlling steam consumption based on electrolyte temperature. This will minimize steam line pressure fluctuations. INTRODUCTION In the mid 1920’s the Nichols Copper Company of Laurel Hill, New York recognized the need for a modern copper refining facility in the southwest. Due to the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the logical location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Energy costs (electrical and thermal) are critically important in the viability of modern copper electrorefineries. The El Paso Refinery produces electricity and steam through its cogeneration system. The El Paso cogeneration facility is a natural gas, 15-megawatt facility containing five turbine generators and associated waste heat recovery boilers. The facility is divided into two phases. Phase I consists of two Allison 2.2-megawatt turbine generators. Phase II consists of three Solar Taurus 3.5-megawatt turbine generators. Presently three units in Phase II are operated. The Phase I units were purchased and installed in 1986 and the Phase II units in 1992 (Solar 1991). The facility operated at full capacity until 2003 when steam demand was significantly reduced due to decrease in cathode production and closure of the copper sulfate and precious metal operations. Phase I units were taken out of service and put on care and maintenance status.

Jan 1, 2019

By S. Torres, J. Álvarez, R. Castillo, R. Fuentes, C. Sandoval, R. Parra, Myakalwar A. K., M. Velázquez, J. Yáñez, D. Sbarbaro

Rapid analytical assessment in copper mining industry is a limiting factor for operational purposes and for the improvement of processes. The present work aims to review the analytical assessment in the copper industry utilizing emerging spectrochemical techniques such as laser induced breakdown spectroscopy (LIBS) and UV-Vis-IR Hyperspectral Sensing. LIBS is a plasma based spectroscopic method where the sample surface is irradiated by high power laser. The light emitted from the plasma contains atomic -molecular spectral information and can be detected using a simple CCD based spectrometer. UV-Vis-IR Hyperspectral Sensing is produced by the reflection of light from the sample’s rough surface in all directions and it can be collected by using an ellipsoid or paraboloid mirror arrangement. The electromagnetic radiation emitted by the samples in the UV-Vis, NIR and MIR region can be used for molecular characterization. The spectrometer splits different wavelengths through a CCD arrangement in 2D spatial and spectral dimensions, thus a hyperspectral cube of data is generated. Chemometric techniques such as principal component analysis (PCA), K- nearest neighbors (KNN), support vector machine (SVM) among others, can be applied to LIBS and Hyperspectral data for better classification and quantification purposes in copper ores. Real- time determination of elemental and mineral species used for online processing control will help to achieve the copper industry 4.0. INTRODUCTION The demand for copper mineral resources is intensely growing with the increase in population, per capita GDP, the development of new technologies and the increase in global living standard. With the rise in consumption of copper, it is important to optimize mining and metallurgical processes tending to the copper industry 4.0 (Ge, Song, Ding, & Huang, 2017). The real-time analytical assessment in the mining and metallurgical processes is a crucial part for allowing the global improvement in mining industry. The features considered for better analytical assessment are the instrumental automation and interconnection, real time results, low cost, quality in terms of accuracy and precision. Furthermore, improving recovery (extraction), timing and quality of final products avoiding environmental impacts. Some elements such as Cu, Fe, Ag, Au, Mo, S, As, Pb, Zn are important to be determined in the process control. Additionally, rapid mineral identification of few species such as CuFeS2, Cu4FeS5, FeS2, CuS, Cu2S, MoS2, Cu3AsS4, FeAsS, among other can be challenging.

Jan 1, 2019

By Alastair Torrance, Italo Onederra, Do Sun Kim, Kush Patel, Gary Cavanough

Reactivity of ammonium nitrate-based explosives is associated with the presence of sulphide in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. This paper explains the mechanism of these reactions, the potential cause of spontaneous detonation and how inhibited explosives prevent the reaction

Jan 1, 2019

By Victor Munoz, Jorge Oliva, Gonzalo Marias

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth.

Jan 1, 2019

By T. M. Klemetti, T. J. Batchler, T. Matthews

From 2013–2017, there were over 1,120 documented injuries, including fourteen fatalities, from ground falls in underground mines in the United States (MSHA 2017). The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. The load-displacement characteristics of an 8-ft x 12-ft area of 8-gauge welded-wire screen were evaluated using a test frame designed for testing multiple load-pull locations. In previous tests, load-pull contact was always in the center of the bolted screen section. In this study, larger pull contact areas are used to simulate roof falls. The information obtained in this and similar studies can be used to better understand the loading behavior and surface control capability of roof screen in underground mines. INTRODUCTION AND BACKGROUND The large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. Previous tests to evaluate the performance characteristics of various types of screen have been conducted by the University of Alberta (Tannant, 2001). In this study, the load-displacement properties of welded-wire, chain-link, and expanded-metal mesh were measured by performing full-scale pull tests. A flat steel plate was pulled through a screen test sample that was bolted to a special test frame while the pulling force and mesh displacement were measured. These tests established the general load-displacement behavior of the screen. Peak load capacities and stiffness were determined for each screen type, showing how welded-wire mesh has a much stiffer initial loading response, whereas chain-link and expanded-metal mesh have large displacement capabilities and exhibit significant post-peak ductility.

Jan 1, 2019

By Thomas L. Barkley

My historic auditing of Underground Drilling and Blasting Practices has demonstrated to the author the need for reviews of many mines' procedures in these processes. Poor understanding of the basic principles and practices of the drilling and blasting science in Underground Development Mining has created significant costs to mining operations in many instances.

Jan 1, 2019

By G. A. Sutton

This paper, describes a case example from San Manuel mine, where in situ copper leaching of the supergene zone was done over a 14 year period (1986–1999) in conjunction with underground and open-pit mining operations of a copper porphyry deposit. In 1993–1994, testing of well fields was done to determine the amount of copper that would be recovered from in situ leaching of the supergene zone, which was composed primarily of chrysocolla and copper-clay minerals. It was determined that the leach fluid would reach 70% (‘sweep efficiency’) of the copper minerals and that 75% of them would be leached for a recovery of 52% of the acid soluble copper. However, the final results from Zone 6, which had the longest leach history, showed that approximately 42% of the acid soluble copper was recovered, indicating that the `sweep efficiency’ was closer to 55%. Comparison of drill-core assay data from two holes, one drilled before (ARM158) and the other after (SMO9607) leaching, also indicate that approximately 42% of the acid soluble copper was recovered. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to a combination of factors, including difficulty in maintaining fluid saturation, channeling effects and gypsum precipitation. INTRODUCTION In situ copper leaching at the San Manuel mine, Arizona, was initiated in 1986. It was recognized that some of the copper oxide resource was not going to be economically recoverable by conventional open pit and heap leach methods using solvent extraction and electrowinning (SXEW). A high stripping ratio would be required to access part of the resource. At the time, in situ leaching was becoming popular in the uranium industry but the approach was virtually unknown in the copper industry, especially not at a large scale.

Jan 1, 2019

By Xian Jian Guo, Lei Li, Hua Wang

Direct smelting of copper concentrate to blister copper has the advantages of energy saving and environmental protection. There has been a lot of effort invested in process development including test work and theoretic analysis in the past half century. However, the process has only been applied commercially to a few smelters that treat chalcocite types of copper concentrate. The main limitation to treating chalcopyrite types of copper concentrate is high copper content in smelting slag and low direct copper recovery. Thus intensive slag cleaning is needed. In this paper, the thermodynamic analysis was mainly carried out for the multiphase equilibrium of direct to blister copper smelting for both chalcopyrite and chalcocite concentrates. The practical problems in direct to blister copper smelting, which are mainly in copper content in slag, are clarified. The operational window of slag composition for different temperatures and oxygen partial pressure for the treatment of chalcocite type concentrates is identified. The process operation optimization for the blending of chalcocite, pyrite and chalcopyrite concentrates was done. INTRODUCTION The extractive metallurgy of copper can be divided into two broad groups of processes, namely, pyrometallurgy and hydrometallurgy, and the former is dominant. About 80% of copper in the world is produced by pyrometallurgy (Christopher et al., 2006). The first stage of conventional copper pyrometallurgy processing is to smelt copper concentrate to copper matte composed of FeS and Cu2S with slagging to remove a proportion of the iron (Gargul, Boryczko, & Bukowska, 2017). The smelting processes include bath and flash smelting. The second stage of the process is to convert copper matte to blister copper. In most cases, the copper matte is converted in Peirce Smith (P-S) converters, which are batch operations (Kubiszewski, 2015). The P-S converting can be divided into two periods, slagging and copper blowing. During slagging period, FeS in copper matte is oxidized to FeO, which reacts with silica flux forming slag. When the iron content in matte is less than 1%, copper begins to oxidize and reduce to form blister copper (Kucharski, Sak, Madej, Wędrychowicz, & Mróz, 2013).

Jan 1, 2019

By J. Etcheverry, E. Seguel, R. Díaz, F. Parada, R. Parra, E. Balladares

A thermodynamic and kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite during partial roasting of enargite-containing copper concentrates. The proposed mechanism involves solid-solid-gas and solid-gas reactions between chalcocite, pyrrhotite, gaseous sulfur and oxygen. The formation of bornite could be explained by a two-step reaction: the first one involving the formation of chalcopyrite by a reaction between Cu2S, FeS and gaseous sulfur, followed by a second step in which the newly formed chalcopyrite reacts with additional chalcocite to form bornite. Although thermodynamically the direct formation of bornite is more favorable than that of chalcopyrite, the lower diffusion kinetics of bornite formation could explain the preferential formation of chalcopyrite. If the reaction occurs with stoichiometric chalcocite and pyrrhotite in the presence of gaseous sulfur to form chalcopyrite, no bornite is formed, while for the stoichiometric reaction between chalcopyrite and chalcocite in the absence of sulfur, only bornite is formed. For the formation of magnetite and chalcopyrite the mechanism could involve the partial reaction of chalcocite and pyrrhotite in the presence of oxygen. The proposed model is thermodynamically consistent with the experimental results obtained in laboratory and pilot plant. INTRODUCTION The processing of high-arsenic copper concentrates with over 0.7 wt.-% arsenic by conventional smelting-converting normally require an additional arsenic removal step to reduce arsenic content to levels below 0.2–0.3%. One of these high-arsenic copper concentrates is the one produced by the Ministro Hales Division (DMH) of CODELCO, which has the typical chemical composition shown in Table 1. Enargite (Cu3AsS4), chalcocite (Cu2S) and pyrite (FeS2) are the main mineralogical species present in these concentrates, with over 75 wt.-%, as shown in Table 2. Partial or “neutral” roasting of these concentrates under controlled temperature and partial oxygen pressure conditions at 923–993K (650–720ºC) can remove up to 95% of the arsenic as As2S3 (As4S6), which has a high vapor pressure under these conditions, leaving a calcine with low residual arsenic. In copper concentrates, arsenic is present generally as enargite and arsenopyrite. This compounds as well as others such as pyrite and covelite, decompose readily above 770 K (500ºC), releasing, in addition to gaseous arsenic trisulfide, gaseous sulfur which by oxidizing to SO2 generates most of the heat required by the process.

Jan 1, 2019

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

By R. T. Seaman

There are several hydrometallurgical alternative processing options under development for high enargite and arsenic containing copper concentrates ranging from biological, atmospheric, medium temperature oxidation to total oxidative leaching. The most developed of these options is the CESL process boasting pilot campaigns totaling more than 8760 hours of fully integrated continuous operation, as well as, over two thousand batch scale oxidation tests performed on dozens of concentrates for flowsheet development. This paper reports the observed deportment of arsenic under varying arsenic, iron and acid oxidation conditions; it also describes the impact of iron to arsenic ratios and residue recycle on overall arsenic behavior and its stability in residue. INTRODUCTION The CESL Hydrometallurgical Process (CESL) was originally developed to compete with smelting of clean chalcopyrite concentrates. High Treatment Charges and Refining Charges (TC/RCs) combined with premiums on London Metal Exchange (LME) grade copper from onsite refining made treatment of copper concentrates using CESL a viable option at the time. As world demand for copper increased and a subsidized Chinese refining market developed, smelting contracts became more favourable for the miner and focus was placed on modifying the CESL Hydrometallurgical Process to handle concentrates with elevated deleterious elements. Dozens of pilot campaigns processing concentrates containing elevated concentrations of uranium, fluoride, mercury and nickel all led to further developments of the CESL Hydrometallurgical Process. In 2016 a United States patent was granted for a novel modification of the CESL Hydrometallurgical Process for recovery of copper from arsenic-bearing and/or antimony-bearing copper sulphide concentrates, Henry Salomon de Friedberg (2016). To date, over 2000 bench scale tests along with five fully integrated closed loop pilot campaigns, totaling over a year of online operation time, have been conducted processing arsenic bearing copper concentrates. This paper summarizes the observed behavior of arsenic under varying autoclave and process conditions.

Jan 1, 2019

By Tristan Worsey, Nathan Rouse

Florida is one of the major limestone producing states in the United States. The state has unique regional geology and groundwater characteristics that require equally unique mining methods to extract limestone for construction materials. In many regions, aggregates quarries operate by drilling and blasting underwater limestone and then digging the muck with large draglines, while in others, mining operations are able to operate above the water table.

Jan 1, 2019

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By K. Scalise, M. Teixeira, K. C. Kocsis, J. Parrish

"This paper aims to introduce and discuss a newly developed algorithm, which can be uploaded on smart watches and other mobile devices to inform and protect underground personnel working in hot and humid environments. Using this algorithm, the metabolic rate (M) of a worker can be determined in “real-time”. In addition, besides warning signs and alarm signals emitted by the smart watch, the algorithm has the ability to determine work-rest time periods based on the worker’s physiological parameters (e.g. age, height, weight, gender) and the climatic parameters (Td, Tw, flow velocity). This paper also investigates whether a re-designed auxiliary ventilation system can provide appropriate work conditions in the production stopes. INTRODUCTION An underground environment with high temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to heat-related illnesses such as heat rash, heat cramps, heat exhaustion, and heat stroke. Heat stroke is a serious illness that carries a high risk of fatality, if the underground workers are not immediately treated and the climatic conditions are not corrected (McPherson, 1993). There are two methods used to control the climatic conditions in underground mines: (1) Using ventilation and cooling systems to reduce the thermal stress on the mine workers, and (2) Reducing the heat transferred to the ventilating air from major sources such as: strata, auto-compression, mining equipment, groundwater, blasting, etc. The heat from strata and auto-compression is transferred to the ventilating air at varying degrees, based on factors such as the virgin rock temperature (VRT), the thermal properties of the surrounding rock formations, and the surface air temperature. However, the use of mining equipment and blasting processes can be managed to reduce their contribution to the mines’ overall heat load. To provide appropriate work conditions, selecting the most suitable cooling method depends on the level of heat to be removed, the location of the problem areas, and economic constraints (Brake & Bates, 2002; McPherson, 1993). Because every mine is unique, it is essential to monitor the climatic conditions to select the most appropriate method of cooling. A majority of the time, simply adjusting or re-designing the auxiliary ventilation system can efficiently remove the heat and dilute the contaminants. This may involve moving the ducting system, changing the size of the duct, changing the size of the auxiliary fan, or switching from forcing to an exhausting fan arrangement. If the required air volumes are higher than the existing primary ventilation system can supply, other measures may need to be taken to increase the airflow delivery. This may include regulating the flow in some areas of the mine to increase airflow to the desired area, adding booster fans, or replacing the primary fans."

Jan 1, 2019

By Frank Hirthammer

Productivity, customer relations, and effectiveness of work depend to an ever-increasing extent on a functioning logistics system tailored to the needs of the user. Of course, it is not possible to cover and explain all aspects of the logistical requirements of even a small part of an industry, in a single article. The article speaks specifically about the particularities and differences in the logistical requirements in the explosives sector. Starting with questions of safety, handling and quality up to the legal basis, there are special requirements regarding the logistics in the explosives sector. The results of innovative logistics solutions are presented using three examples from daily work practice.

Jan 1, 2019

By T. Imgrund, A. Bischoff, S. Spürk

"Specific conditions of underground coal mines at great depth, such as high temperatures, high rates of methane inflow and natural ventilation pressure provide considerable challenges for the reliable design of appropriate mine ventilation systems. For decades coal mining in Germany has coped with these extreme circumstances. Based on these experiences appropriate software tools for simulating mine ventilation networks have been developed and continuously enhanced. This paper examines differences in the simulation results and underlying calculation methods of two software solutions. The analysis is based on the comparison of FlowNetTM and VentSim DesignTM (Version 5.1) regarding the accurate prediction of fluid mechanical quantities and their validation with real measurements. A special focus lies on exceptional ventilation scenarios typical for deep coal mines, like gas inflows, fire events and buoyancy effects. The purpose of the comparison is the future utilization of the experiences gained during mining at up to 1,500 m depth for state of the art ventilation design. INTRODUCTION Ventilation is an essential component of mine operations—as providing fresh air to workplaces, diluting and removing explosive, toxic or asphyxiating pollutants and assuring sufficient climate conditions. On the other hand, the costs of ventilation contribute to a large extend to the overall operating costs of a mine, as the share in the energy consumption of a mine may be in the range of 25–50% (Belle, 2008). Accordingly, proper design of ventilation systems has been a task since early times. Consequently software for modelling of ventilation networks has been developed in order to improve efficiency and accuracy of calculations (Maleki, 2018). Compressible flow has not been considered by initial ventilation modelling software tools. In Germany, the consideration of changes in airflow density—depending on pressure and temperature—in the algorithms of ventilation simulation software has been started in 1974 by Duepre & Hofbauer. This development had been continued by the Pruefstelle fuer Grubenbewetterung (Test Centre for Mine Ventilation) and resulted in the release of a computer ventilation software named “Wetter”. The mine inspectorate of the German state of North Rhine-Westphalia, which supervises the major coal mining district in Germany, declared ventilation simulation based on compressible flow being “state of the art” in 1985 (Pollak, 1985). This pronouncement made allowance for assessing the consequences of underground fires and downtimes of main fans based on advanced software solutions."

Jan 1, 2019