Search Documents

By A. Morrison, P. Brito-Parada

"The separation of valuable and gangue minerals according to their surface hydrophobicity in a froth flotation tank occurs in both its pulp and froth phases. In the pulp phase, hydrophobic particles must be brought into contact with rising bubbles introduced at or near the bottom of the tank. In a mechanical froth flotation tank, this is primarily achieved through the agitation of the pulp by an impeller or by a rotor-stator system. However, the turbulent and mixing effects of such an impeller or rotor-stator system, necessary to promote bubble-particle interactions in the pulp, are not confined to the pulp zone, but are transmitted into the froth zone at the pulp-froth interface. This impeller-induced turbulence at the pulp-froth interface is compounded by the impulse of buoyant bubbles entering the base of the froth phase, reducing the stability, and thus separation performance, of the resulting froth. Hence, turbulence improves separation performance if it occurs deep in the pulp phase, but diminishes it if it occurs close to the pulp-froth interface. For this work, a performance-enhancing pulp phase insert was designed to isolate the impeller-induced turbulence from the pulp-froth interface in a laboratory-scale, continuously-operated froth flotation tank. The result was a shifted grade-recovery curve that allows the insert to be designed to maximize the recovery from the system without sacrificing the grade of the concentrate, or vice versa, along a spectrum of improved performance. This paper will present the insert design and development process that resulted in this improved grade-recovery curve, as well as a set of heuristics that could be used to design a similar insert for pilotand industrial-scale validation and deployment.INTRODUCTIONAn almost ubiquitous design feature of commercial flotation tanks is the enclosure of the impeller to create a concentrated turbulent zone (Mavros, 1992). These turbulent zone enclosures are varied-- from the rotor-stator design of, for instance, Outotec cells, to the air disperser design of Wemco cells-- but all share the same rationale: that turbulence is desirable to promote bubble-particle interactions (Ralston, 1999), and to produce smaller bubbles (Wills, 2006), but also undesirable because it promotes the detachment of valuable mineral particles from bubbles, and exacerbates entrainment-inducing mixing at the pulp-froth interface (Jameson, 2010)."

Jan 1, 2018

By V. Runkana, N. K. V. Nadimpalli, S. Sahu

"IsaMill™ has been in operation in the recent past for fine grinding of low grade ores to extract non-ferrous minerals. IsaMill™, typically, consists of a series of uniformly spaced identical disks mounted on a rotating shaft which is encased in an outer shell. The mill offers high energy efficiency for fine grinding and an inherent scalability. But, it encounters certain operational challenges such as non-uniform distribution of grinding media coupled with high wear rate of the disks and solid walls of the mill at specific locations—which adversely affect the mill performance. To circumvent these operational challenges, design modification of the disks through heuristics, by introducing a reduced diameter disk (RDD) at specific locations, is a common practice in industry. But there is no systematic scientific study in this regard. In the current work, we developed a discrete element method (DEM) based model and simulated for the IsaMill™ operation to study the effect of RDD on the efficiency of the mill and wear rate of the solid walls and disks. Since the first set of disks experience the high wear rate due to the high loading of the charge, the RDD was introduced at the first two disks. The simulations were performed at different diameters of the RDDs and at different media loadings. The performance of the mill was analyzed based on the power consumption, the wear rate on disks and the distribution of media particles inside the mill. Besides, the performance variables such as mean velocity of media particles and total impact energy provided useful insights into the milling operation. It was observed that the reduction in disk diameter yields lower wear rate of the disks at the cost of decrease in power draw at a constant high media loading. Whereas, when the media loading was decreased, the amount of wear and power drawn was comparable for both the most reduced and least reduced disk diameters. Therefore, there is an optimum choice of RDD for a given mill loading to maximize the mill performance while reducing the wear rate of the disks."

Jan 1, 2018

By Ivar Eskerud Smith, Ole Jørgen Nydal, Niranjan Reddy Challabotla, Svein Sævik

INTRODUCTION Airlift pumping, utilize compressed air that is injected at the bottom of a vertical pipe submerged in the water, reduces the mixture density inside the pipe and lifts the liquid or mixture of liquid and solids. This type of pumping technology, which is simple and without moving parts submerged in water, which provides several advantages compared to the mechanical pumping. Airlift is used in various difficult pumping applications such as transport of fluids corrosive to metals, explosives, nuclear and toxic materials in chemical industries, diamond mining and coal transport. Application of airlift to deep sea mining conditions was investigated by extensive laboratory experiments [1], theoretical analysis [2], and limited proof of concept field studies [3] starting in 1970’s with the discovery of huge amounts of manganese nodules discovered on the seabed at a depth of ranging from 4000 to 6000 m . Even after extensive investigations over the last five decades, there exists no commercial application of airlift technology for lifting of minerals. The major problems with the application airlift for deep ocean mining was (a) lack of control over the expansion of the injected gas, which increases the velocity in upper part of the riser pipe (b) lower efficiency compared to mechanical pumping [3]. Different flow regimes are encountered in airlift pumping: bubble, slug, churn and annular flow. Annular flow regime is the least efficient in lifting of particles and churn flow has better efficiency [3].

Jan 1, 2018

By V. K. Kuppusamy, M. Holuszko

"Lamps and lighting products are the most commonly used electrical products around the globe. With the improvement in lamp technologies, lighting products have grown complex and hence require an improved recycling process. The LED lamps consist of various valuable metals such as iron, copper, aluminum, chromium, silver, and gold, as well as non-metals such as glass, plastics, and fibers. In addition, there are also traces of hazardous substances such as lead, arsenic, and mercury. A major step in the recovery process is size reduction, and researchers have suggested that up to 40% of the total valuable material is lost during the shredding and grinding processes. SELFRAG is a high voltage selective fragmentation comminution technology that uses high voltage pulses in a water medium to efficiently separate the metals at a coarser size without generating many fine particles. It has been proposed that during the fragmentation process of electronic waste (e-waste), the metals can be separated without fine grinding. This research considers the applicability of high voltage pulse fragmentation for LED lamps. Eight different types of LED lamps were processed through the SELFRAG unit at varying pulses to study metal liberation. The product obtained was characterized for metal liberation, metal grades, and liberation analysis. The specific energy consumption for this size reduction process was also monitored. INTRODUCTION Lamps and bulbs are the most commonly used electrical products in homes, offices, industrial operations, and streets. According to Energy Star research (2006), an average US household has more than 40 sockets for light bulbs and consumes approximately 2100kWh every year for lighting. The development in lamp technology has pushed the boundary for newer products. The LED lamps have been taking over the market from the incandescent bulbs and compact fluorescent lamps (CFL). According to the US Department of Energy (2012) and myLEDlight.com (2007), LED lamps have several benefits over other lamps. LEDs produce light hemi-spherically, which increases their efficiency in directional light emission. It has higher breakage resistance from vibration or transportation. LED lamps use up to 90% less power than incandescent bulbs thus making them highly energy efficient; They have a longer lifespan, lasting 10 times longer than a CFL and 133 times longer than the traditional incandescent bulb. Because of all the benefits, Smallwood (2014) suggested that the market of LED lamps will grow to $12.2 billion by 2018."

Jan 1, 2018

By E. Guerrini, M. Maccagni, J. Nielsen

"Lead is the most important material able to meet the current demand for energy storage. The lead acid battery is reliable, efficient and inexpensive. Continuous developments in battery construction are providing improvements in all aspects of the batteries’ performance. The lead acid battery is both the main lead product and the main raw material for lead production. More than half of the lead produced is from secondary smelters where batteries are the most important feed material. The environmental pressure on lead production has been increasing for many years, and continues to become stronger and stronger. The lead production processes and technologies themselves will require updating to meet the new regulations. Although they are very strict now, they will become even more so and current technologies may not be sufficient. Because recyclability is a strong point for the lead acid battery, the secondary smelters need to reduce the environmental impact as much as possible. In recent years, the secondary smelters underwent impressive changes in this direction, but some more improvements are possible. Electrochemistry can offer a step change improvement in making secondary lead production more environmentally friendly. Engitec has developed an electrochemical process base on a very high current density (high productivity) cell using an inexpensive electrolyte and at a relatively low cost. In this paper, the latest update on the technology is provided. INTRODUCTION The lead acid battery is considered the “walking dead” by some new technologies trying to replace it. It has played and will continue to play a very important role in our lives because it is inexpensive, fully recyclable and the existing lead and the mine reserves guaranty enough material for the extended future. According to the life cycle, the lead acid battery is the cheapest and the most effective system to store energy. Lead is practically a close loop where lead battery production consumes more than 80 % of the produced lead but contemporarily it is the most important raw material for the production of metallic lead. In fact, nowadays, the secondary production has overcome primary production and this trend is expected to continue. Primary lead is the make-up material for the existing battery production and the source of lead for the construction of the new ones."

Jan 1, 2018

By Ian Tolliday

Emulsion Explosives manufacturers are aware of the destabilizing effect that the presence of inorganic impurities such as magnesium and iron and organic impurities such as naphthalene sulfonates and alkyl amines can have on their emulsions. This destabilization often manifests itself as severe crystallization and subsequent product loss. This paper describes the performance testing of specifically developed emulsifiers which give greatly improved emulsion stability in the presence of high levels of impurities. The test work involved a series of stability tests using ammonium nitrate doped with various levels of crystal modifier and anti-caking agent. A further series of tests were done to evaluate the stability using ammonium nitrate doped with various levels of iron and magnesium ions.

Jan 1, 2018

By M. M. Bugarin, P. J. van Staden, V. T. Conic, S. S. Dragulovic, R. M. Kovacevic, D. B. Milanovic

"The mineralogical and physico-chemical characteristics of a polymetallic sample from a mine of West Serbia suggest that it can be classified as a SEDEX type of ore. Those ores contain multiple value components, being inter-dispersed as fine grained aggregates. This prevents concentration by gravity or flotation concentration processes. Mineralogically, the valuable metals (Cu;Zn;Pb;Au and Ag) occur as pyrite, sphalerite, galena, tetrahedrite, chalcopyrite, covellite, arsenopyrite, and non-metallic minerals (barite, and waste minerals). Novel technologies are under development within this project for the recovery of all valuable metals from this very complex material. The work comprises the further treatment of solid residue obtained after Cu and Zn extraction by bioleaching, for the subsequent recovery of Pb and the precious metals Ag and Au. The residue is first treated with a saturated sodium chloride solution, whereupon a chloride solution of lead (NaPbCl3) is obtained. From the chloride solution, lead was deposited in the form of lead carbonate, followed by reductive melting, whereupon lead anode was obtained. Electrolytic refining of the lead anode, using a solution of PbCO3 in methane sulphonic acid (MSA-Methanesulfonic acid, min 99.5% CH4O3S, density 1.48 kg/dm3, Manufacturer: Carl Roth) as an electrolyte, yielded refined lead cathode. It should be noted that, after precipitation and separation of lead carbonate, the sodium chloride solution is restored to its original composition by the addition of make-up reagents and returned for another lead-sulfate leaching cycle. The solid residue obtained after leaching lead-sulphate, is leached in thiosulphate solution, with the addition of an activator, a catalyst and lixiviant for gold, to yield a thiosulphate solution of gold and silver. Since the content of gold and silver in solution is low (below 1 mg/dm3), they are first electrolytically concentrated on steel cathode and then refined to pure metals using well-known chemical methods. Note that, after the electrolytic separation of gold and silver, thiosulphate solution is recycled to the leaching step."

Jan 1, 2018

By Delphine Pierre, Jean-Marie Augustin, Anne-Sophie Alix, Charline Guérin, Cecile Cathalot, Yves Fouquet, Arnaud Gaillot, Ewan Pelleter, Carla Scalabrin, Florian Besson

With the world’s growing demand for metals, seafloor massive sulfides (SMS) deposits are now seen as a possible mineral resource that could contributes to secure metal supply for human needs. SMS deposits are characterized by high concentrations of base metals and at some place high contents of precious and rare metals. Since 1977 and the discovery of the first high temperature (HT) hydrothermal vent and its sulfide mineralization and high biodiversity, more than 300 sites are known today. If the exploration strategy for detection of active hydrothermal sites is now robust, their associated mineralization will not (and must not) constitute a potential target for deep-sea mining due to environmental concerns and technical limitations. Recent studies on SMS deposits are rather focused on extinct and buried mineralized sites characterized by a lower biomass. Several geophysical techniques to explore and detect extinct SMS (eSMS) and buried SMS (bSMS) have been developed (e.g. Kawada and Kasaya, 2017; Szitkar et al., 2017, 2014) using different approaches (e.g. regional or local scale; ship-based or using underwater vehicles) with several degrees of success or limitation. Here we present results from acoustic surveys performed on the TAG hydrothermal district during the BICOSE (2014) and LEVE-SMF (2016) cruises and direct observation provided by HOV (Nautile) dives carried out during HERMINE cruise (2017). Acoustic data were acquired using two different multibeam echosounders (MBES): the hull-mounted Kongsberg EM122 (12 kHz, R/V L’Atalante) and the ROV-mounted RESON SeaBat 7125 (400 kHz, ROV Victor) (Figure 1). After processing, acoustic seafloor backscatter data from both MBES provides complementary qualitative results in relation to the seafloor composition. The analysis of the seafloor backscatter data obtained by near-seafloor surveys with the high-resolution 400 kHz MBES shows a clear relationship between low backscatter strength values and areas covered with pelagic and hydrothermal sediments whereas high backscatter strength values are associated to pillow lavas and basaltic scree. Intermediate backscatter strength values are rather related to old and younger eSMS as well as to mineralization on TAG active mound.

Jan 1, 2018

By M. McClintock

"High Pressure Grinding Rolls (HPGR) is increasingly being chosen for comminution circuits for its energy-efficiency for hard rock mining operations. Despite HPGR’s growing popularity, geo-metallurgy programs are still prohibitively expensive because of large sample requirements. Traditionally, sizing HPGR application requires a significant amount of sample, in the order of 1 to 10 tonnes, depending on the level of study and complexity of the resource. Therefore, engineering and design of HPGR circuits typically are reliant on few composites that are required to be representative of the resource and mine plan. Three bench scale HPGR test methodologies were developed in 2015 at NBK Institute of Mining Engineering at the University of British Columbia (UBC) capable of defining the energy size breakage relationship of pilot HPGR. These methodologies were developed to allow bench scale testing for different levels of study from PEA (Preliminary Economic Assessment) to detailed design and operations. The Piston Press test defines the energy size reduction relationship by measuring specific energy consumption and corresponding feed and product size distributions. The advantage of Piston Press testing is the small sample requirement of 5 to 10 kg. Small sample requirements allow multiple samples to be tested across a deposit. Piston Press testing allows extensive geo-metallurgy programs that can determine ore variability and inform in optimization and production planning. To date, the Piston Press methodologies have been validated on a pilot-scale HPGR unit located at UBC. Recently, testing was conducted to calibrate and validate the Piston Press test against full-scale HPGR on a gold sulphide ore deposit. The program included the collection of operational data with the respective HPGR feed and recycle sample. Sample collected was used both for Piston Press testing and HPGR piloting. This paper discusses the test-work and results as carried out during this program, using the aforementioned methodologies."

Jan 1, 2018

By Samantha Whisman, James R. Hein

Hydrothermal marine manganese-oxide deposits (HMMD) are cemented and variously replaced volcaniclastic and biogenic sediments that were mineralized by distal, low- temperature, hydrothermal fluids. HMMD predominantly form below the seabed as sediment-hosted statabound deposits but can also form on the seabed. These deposits form at oceanic and back-arc basin spreading centers, volcanic arcs, and mid-place hotspot volcanoes. HMMD have traditionally not been considered to have an economic potential because they were considered to be devoid of economically valuable critical elements. This contrasts with their non-hydrothermal counterparts, ferromanganese crusts and nodules, which are enriched in many critical elements. However, manganese is now one of the critical metals and HMMD have the highest manganese contents (up to 55% Mn, so- called battery-grade Mn) of all the types of deep-ocean mineral deposits. There is a growing demand for this critical metal and an upward trend exists in the price of manganese on the global market. Also, other critical elements can occur in high concentrations in some HMMD and their economic potential has not been considered, especially for lithium (up to 0.17%) and molybdenum (up to 0.24%), but also vanadium (to 820 ppm), chromium (to 346 ppm), and nickel (to 0.45%), among others. Which of these critical elements are enriched and their concentrations depend on the types of rocks leached at depth by the hydrothermal fluids, the composition of hydrothermal minerals precipitated in the higher temperature parts of the circulation system, and the types of sediments mineralized by the manganese oxides. For example, mineralization of a carbonate sediment resulted in the highest lithium contents, whereas leaching of ultramafic rocks at depth as a rule results in the highest chromium and nickel contents in the HMMD. These deposits are known to be widespread, especially in volcanic arcs, but their lateral and vertical extents and consequently size, tonnage, and grade have not been determined. Most samples of hydrothermal deposits have been collected by dredging and therefore the in situ relationships often are not known. One sample from the Mariana volcanic arc, west Pacific, was collected by ROV at 1274 m water depth from a layered outcrop 6.6 m thick that may be a sequence of pervasively mineralized volcaniclastic layers and offers the first clue as to the potential vertical extent that these deposits may attain. However, only the top ~0.4 m-thick layer was sampled, so it is not known whether the mineralization extents throughout the outcrop. Although large manganese deposits of various origins occur on the continents, they consist of manganese carbonates, silicates, or complex mixtures of manganese minerals. In contrast, marine hydrothermal HMMD exhibit relatively simple mineralogy that would make processing of this potential ore much simpler.

Jan 1, 2018

By Y. Idrogo

Electronic delay detonators have been used in most types of blasting application with great success, with the accuracy and precision being used effectively to control negative environmental impacts like vibration. They have also provided consistent repeatable fragmentation and heave results. With the very wide choice in delay period and powerful timing design software, the choice of firing times to optimise blast results is not always clear to the designer. So the improved results achievable from the use of electronic delay detonators are often not optimally achieved.

Jan 1, 2018

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

By D. Vega, P. R. Brito-Parada

"Small diameter (10 mm) hydrocyclones have been applied successfully for the separation of particle suspensions in the micron size range. These hydrocyclones are attractive because they show a bypass fraction larger that the water recovery, resulting in a high particle recovery to the underflow as well as low water recovery. However, this is a disadvantage when the purpose of the hydrocyclone is classification because of the large amount of fine particles that are misplaced in the underflow. The aim of this study is to explore, experimentally and computationally, the influence of design parameters on the classification process. In this work, a full factorial experimental design was defined to carry out comprehensive experimental tests using glass beads (0-20 µm) as the particulate system. We show that the dimensions of spigot and vortex finder diameter can be effectively manipulated to change the separation performance of the system and the energy consumption. A CFD model was developed that is able to predict particle size distribution. The numerical results for the partition curves showed very good agreement with the experimental data. INTRODUCTION Small diameter hydrocyclones are a very attractive separation technology for fine particle suspensions. Since the hydrocyclone diameter is directly proportional to the cutsize that can be achieved, 10mm hydrocyclones have been shown to be very effective in collecting particles in the micron-size range. In addition, while in large hydrocyclones the bypass, i.e. the fraction of particles that report to the underflow without classification, is similar to the water recovery, in 10mm hydrocyclones the bypass fraction is considerably larger than the water recovery. Its high particle recovery and low water recovery makes small hydrocyclones ideal for ultrafine particle classification and dewatering applications in mineral processing. The separation of mineral suspensions achieved using small hydrocyclones has been the focus of various studies. Pasquier and Cilliers (2000) derived a general classification model from experimental data of fine silica concentration in 10mm hydrocyclones; the model was able to describe the fish-hook partition curve. The effect of operating conditions has also received some attention in the literature. Cilliers et al. (2004) showed that an increase in temperature positively effects the recovery of fine silica particles in small hydrocyclones, by increasing the bypass and decreasing the cutsize. Neese et al. (2015) showed that the cutsize in 10mm hydrocyclones can be further decreased by operating at higher pressure, which also trebled the throughput."

Jan 1, 2018

By R. F. Favreau, Patrice Favreau

In many quarries and construction sites visited by the authors over the last 50 years, the latter have observed muck piles from blasting with explosives, which included numerous large blocks, in some cases of dimensions larger than the input to the crusher. The names of these sites cannot be given in the article because the owners insist that data obtained on such visits be kept confidential. Often the blasters felt that the natural fissures in the rock would compensate for the use of a low powder factor, and they asked the authors to explain why such blocks were present. A detailed analysis of the situation often indicated that the cause of the blocks is that explained by figures such as 6 and 7 below in the article.

Jan 1, 2018

By T. Kalliomäki, B. P. Wilson, M. Lundström, J. Aromaa

"The diffusion rate of cupric ions and limiting current density are important factors that determine the rate of copper mass transport in electrolytes proximal to the electrodes used in electrorefining. As a result, diffusion can critically affect both the rate and morphology of cathodic copper deposition thus it is crucial that it be optimized to improve production. The diffusion coefficient of cupric ion (DCu(II)) in copper electrolytes has been previously researched but the values detailed in the literature show significant variations and moreover arsenic - a common impurity - is generally excluded. Furthermore, in previous studies the models have only been validated with model solutions rather than real industrial electrolytes. In this study, the limiting current density and diffusion coefficient of cupric ion were defined for synthetic electrolytes containing copper (40–60 g/dm3), nickel (0–20 g/dm3), sulfuric acid (130–220 g/dm3) and arsenic (0–45 g/dm3). The cathodic limiting current densities were measured at three temperatures (50, 60, 70 °C) with linear sweep voltammetry using the rotating disc electrode (RDE) as the cathode. By utilizing the limiting current density, models for the DCu(II) were constructed using Levich equation. The validity of the DCu(II) model for technical use was confirmed through their application to industrial electrorefining electrolytes with known element concentrations. Consequently, this study provides improved models for limiting current density and diffusion coefficient of cupric ion that can be utilized for industrial process optimization.INTRODUCTION For an efficient copper electrolysis process, the mass transport of copper ions has to be effective. The main mass transport types of copper ions in copper electrorefining are diffusion and convection while the effect of migration is negligible. In order to maintain good mass transport, it is beneficial to keep both diffusion and convection high to maximize the limiting current density (jlim) (Bard and Faulkner, 2001). jlim is the highest current density that can flow in the cell, thus by maximizing jlim the deposition time can be minimized and the good quality of cathodic copper can be ensured. Thus, it is important to research possibilities that increase and optimize diffusion since slow diffusion in the electrolyte limits the rate of the process (Levich, 1947; Moats et al., 2000; Subbaiah and Das, 1989)."

Jan 1, 2018

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

"The aim of this study was to develop a hydromellurgical processing for removal of arsenic from high-arsenic copper sulfide ores and concentrates, providing increase in copper recovery. In this study, three different enargite ore samples containing 28.2–46.7% copper, 1.9–15.0% arsenic and 10.6–27.5% iron were used to determine optimum conditions for the extraction of copper and removal of arsenic. High pressure oxidative leaching process was preformed using various leaching reagents such as sulfuric acid (H2SO4), ferric sulfate (Fe2(SO4)3), hydrochloric acid (HCl), ferric chloride (FeCl3), sodium sulfate (Na2SO4), sodium chloride (NaCl) solutions and distilled water (DW), respectively, under the fixed conditions which were selected to be as follows: NaCl concentration, 0.34 M; concentrations of other leaching reagents, 0.1 M; particle size, -45 ?m; pulp density, 100 g/L; agitation speed, 750 rpm; leaching temperature, 160 ?C; leaching time, 60 min and total pressure (oxygen gas and vapor pressure) into an autoclave, 1 MPa. Results show that under the leaching conditions, more than 90% of copper leaching was achieved with lower than 2% arsenic content as a consequence of the formation of arsenic precipitates in a solution of Fe2(SO4)3–NaCl. It was determined that copper, arsenic and iron concentrations in the pregnant leach solution were 42 g/L, 0.3 g/L and 0.3 g/L, respectively. As a result, it can be concluded that the Fe2(SO4)3 solution in the presence of NaCl or FeCl3 are more efficient leaching media compared to other leaching agents under the high pressure oxidation conditions, because of their high copper recovery and lower arsenic level in the pregnant leach solution.INTRODUCTION Generally, copper is usually produced from copper sulfide ores by a combination of several processes which are flotation and smelting followed by refining [1-3]. Arsenic content in copper sulfide ores tends to increase due to the depletion of high grade copper deposits, hence conventional mineral processing and metallurgical processes cannot effectively treat these ores containing high levels of arsenic to obtain consistently high purity copper concentrates. Because high levels of arsenic in copper ores/flotation concentrates reduces the value of concentrates due to the restriction of smelting process and causes it to be a source of environmental pollution [4-6]. From this point of view, the known way of prevention against high-arsenic copper sulfide concentrates in further metallurgical treatments is to develop economically and environmentally competitive technologies for removal of arsenic impurity from copper sulfide ores before treating the ores/flotation concentrates by the pyrometallurgical routes."

Jan 1, 2018

By V. A. Zhilina, I. V. Shadrunova, O. E. Gorlova

"The aim of the study is to develop and scientifically justify a new adaptive approach to the separating processes of deep and complex processing technogenic mineral raw materials. Technogenic mineral resources as a waste of mining and processing industry are mostly complex objects that have specific features of material composition and technological properties and make it processing ineffective with traditional schemes of mineral raw materials enrichment. Mineral wastes are regarded in this study as a complex object with a large number of signs in conditions of uncertain environment and object. However, adaptation is regarded as the process management system’ adaptation to the specific the properties of the object and the environment that has several hierarchical levels corresponding to different stages in the management of complex object. An adaptive approach is considered as a methodological basis of multivariate schemes for opening the mineral resources and creating mechanisms that could transfer these potential technogenic resources to the actual that significantly expand the mineral resource base of the country's black, coloured, rare, noble metals and construction materials. In this case, potentially the solution to the most pressing social and environmental problems associated with the adverse effects of past economic activity simultaneously with the commercial objectives. This approach to the wastes mining and related processing manufacturers meets the core idea of sustainable development as the balance of interests of State, society, business, private enterprise and each person in the areas of rational use of resources, economic efficiency and environmental safety. On the example of metal-containing raw materials in the form of slags of ferrous and nonferrous metallurgy, ferrous metallurgy sludge, mature fine tailings, the application of adaptive approach illustrates to the development of technologies of its deep and complex processing as phased, thoughtful movement from a comprehensive study of technogenic raw materials to build optimal topologies of technological schemes for processing the mineral wastes. INTRODUCTION Involving the Russian economy in the system of global economic relations significantly changes the nature of the country's competitiveness in the development of the world market and urgently requires competent management of its own natural and mineral resources. The latter at the present time in real economic processes cease to be a passive material foundation and become the producing basis in the production processes in the status of so-called natural capital. Introduced in the field of economic theory at the end of the 20th century, this term means both the flow of natural services and real natural resources. Consequently, natural objects, which act as natural resources of a certain production, today must necessarily be evaluated in a strategic sense. Modern standards of sustainable development presuppose that the economy should equally be oriented to balance the interests of the state, society, business, individual enterprise and each person in the spheres of rational use of resources, preservation of healthy ecosystems, ensuring well-being, high quality of life and environmental safety of not only the current generation, but also respect for the rights of future generations, that is, intergenerational equality. Most types of minerals are classified as non-renewable resources, therefore resource-saving in the sphere of mineral and raw materials complexes is one of the most important factors-indicators characterizing the degree of approximation to the model of rational subsoil use, and, consequently, sustainable development (State Report, 2017)."

Jan 1, 2018

By I. Yochev, A. A. Metelev, A. I. Stepanenko, A. P. Purgin, M. G. Viduetsky, A. M. Panshin, I. F. Garifulin

"Pneumatic flotation cells of the KFM series are intended for the concentration of various ores and technogenic materials. The key operating principle of the flotation cells of the KFM series is the preparation of pulp for flotation in blowers, offering the advantage of an accelerated flotation process. This report summarizes the results of the implementation and operation of the KFM cells at Russian and foreign projects in 2015-2017. Their implementation and operation experience confirms the high efficiency of the KFM cells, especially in the head of lead and zinc, copper and zinc, copper flotation processes:head KFM-600 flotation cell recovers from lead-zinc ore (Rudmetal AD modular concentrator) up to 52% of lead in a single stage (without cleaner flotation) in a salable lead head concentrate (grade of up to 76% lead, 2.3% zinc). The flotation cell proved to be much more efficient than originally expected in the process description in the design phase,flotation of the copper-zinc ore from Novo-Shemur deposit (PJSC Svyatogor concentrator) in two KFM- 1400M cells recovers up to 65% of copper and 70% of zinc in a high-grade bulk copper-zinc concentrate containing 12-13% of copper and 25-28% of zinc. The installation of the two cells with a combined capacity of 26 m3 allowed to decommission 4 chambers of FPM-16 pneumomechanical flotation cells with a combined capacity of 64 m3 with a simultaneous increase in the overall ore concentration performancea single KFM-1400M cell (13 m3) recovers from the copper ore from Volkov deposit (PJSC Svyatogor concentrator) 53% of copper into a high-grade copper head concentrate (33.0% of copper). For comparison, the pneumomechanical cell FPM-16 (capacity 16 m3) has almost half as low copper recovery (29.6%) into the head concentrate at a lower grade (30.5% copper)."

Jan 1, 2018

By Det Juridiske Fakultet, Maria Madalena das Neves

The ocean is increasingly seen as the answer for a myriad of challenges facing humankind. In effect, in addition to being vital for transportation and communication, the oceans contain living and non-living resources that are essential to meet the demand for food, and to the development of pharmaceutical products, energy resources, and high-technology products. This entails that the oceans are under pressure by different activities: navigation, fishing, oil and gas exploration and production, renewable energy development, laying of cables and pipelines, marine scientific research, bioprospecting, and deep-sea mining for minerals and metals. The growing demand for essential minerals and metals such as cobalt, nickel, zinc, copper, and manganese, seen in tandem with technological advances in deep-sea mining, makes the latter an increasingly attractive activity, both in areas within and beyond national jurisdiction. At the same time, the further development of deep-sea mining adds to the problem of the competing uses of maritime space and accentuates the need to balance and articulate the interests of the different users of the seas (States, sponsored deep-sea mining investors, oil and gas investors, fishermen, shippers, etc.). Furthermore, as deep-sea mining activities increase and move on to an exploitation phase so does the possibility of new disputes (for instance during deep-sea mining exploitation a communication’s cable is severed, a vessel conducting deep-sea bottom fisheries damages deep-sea mining equipment, etc.).

Jan 1, 2018

By Ralph E. Burnham, Jeff Taylor, Jonson Montgomery, J. Kelly Ratliff, Rennie Montgomery, Martin Brashear

Top priorities for all blasting companies and individual blasters are risk management, safety of company personnel and the general public, regulatory compliance, and liability protection. On a daily basis, hundreds of shots are detonated by well-trained, skilled, and experienced blasters without incident. Unfortunately, accidents inevitably occur, which is why blasting is considered an “ultra hazardous” or “inherently dangerous” activity from a legal perspective. Despite countless regulations, recent advances in technology, improved training, ongoing research, and improved communication in the industry, mistakes and the resulting incidents continue to occur during blasting operations. These result in dangerous or deadly flyrock, site security lapses, increased complaints, blast damage claims, and lawsuits, which lead to increased insurance costs and other financial tolls for blasting companies. In life, lessons learned the hard way are rarely forgotten. The same is true in blasting operations. Blasting missteps and the resulting events are often the best catalysts for improving risk management and thereby reducing accidents, liability, and financial tolls. This paper provides a summary of two incidents, one safety and the other liability related, and the errors that resulted in a fatality in one case and a multi property lawsuit in the other. The two incidents provide examples that serve as a case study for lessons learned the hard way in blasting operations and offer guidance for the considerations that blasters and blasting companies should incorporate into daily operating procedures.

Jan 1, 2018