Search Documents

By P. Yu, L. X. Liu

"A mechanistic model for tumbling mills was developed during PhD studies at the JKMRC. The concept was presented at the IMPC of 2014, followed by progress in a sub-process of the model presented at the IMPC of 2016. Additionally, a number of papers on the sub-models and breakage function have been published. This paper provides a consolidated summary of the outcomes and status of the model. The overall model structure is presented along with the sub-models such as appearance functions, breakage rate functions, energy distribution, transport, and multicomponent grinding interaction model. The strengths and capabilities of the model structure as achieved to date are presented. The gaps in knowledge and sub-processes are also presented, providing a guide to the areas that require further research and development. It is proposed that the approach developed in this paper provides a structure that can accommodate future mechanistic, dynamic mill model evolution that can incorporate the latest research outcomes and provide a platform to test modelling improvements. This can assist in substantially improving the predictive mill modelling capability in the industry, the importance of which should not be underestimated for this workhorse of mineral processing.INTRODUCTION Grinding is almost the largest single energy-consuming process in the mineral processing industry, which was estimated that about 0.2% of global, and 1.3% of Australia’s electricity is consumed by comminution of gold and copper ores (Ballantyne and Powell, 2014). Although there are some relatively new grinding mills, such as stirred mills, vibrating mills and HPGRs (High-Pressure Grinding Rolls), etc., tumbling mills, as the traditional grinding facilities, are more extensively used."

Jan 1, 2018

By Brian Hawkins, David Bradley, Rachel Gooding, Lucas Rodriguez, Patrick Wilson, Kevin Wegman, Dhruv Mittal

The Department of Homeland Security (DHS) has undertaken a probabilistic risk assessment (PRA) approach to quantifying the infrequent, yet high-impact explosive terrorist attacks on the United States (US) homeland and aiding in mitigating that risk through efforts ranging from intelligence gathering, defense postures, detection architectures, partnering with industry to prevent acquisition, and informed medical response. Based on an evaluation of existing model options, a path to the realization of an exterior explosive model (EEM) that builds upon existing models while meeting runtime requirements, maintains consistency with existing DHS chemical, biological, radiological, and nuclear (CBRN) consequence models, and provides sound estimates of the human health consequences of explosive terrorism attacks in open-air urban and rural environments.

Jan 1, 2018

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

By Shinji Muraishi, Shinji Kumai, Yasutaka Kedo, Takashi Kambe

"Magnetic pulse forming (MPF) is one of the extreme high-speed forming processes. A metal sheet which is accelerated by electromagnetic force is collided onto a mold and fine and sharp details of the product can be obtained. The deformation mechanism of the MPFed metal cannot be understood only by the microstructure observation of the deformed metal. The deformation behavior of the metal should be investigated also by considering the local microstructure change with strain, strain rate and temperature change during deformation. Numerical analysis is an effective method to achieve this requirement. In this study, pure Al and Cu sheets were deformed by MPF. Impact velocity of the metal sheet was calculated by using ANSYS Emag-Mechanical. Based on the obtained impact velocity, the deformation behavior of the metal sheet was reproduced, and local strain, strain rate, and temperature were analyzed by using ANSYS AUTODYN. The relationship between the local microstructure change of Al and Cu sheets and the deformation parameters was examined.INTRODUCTIONMagnetic pulse forming (MPF) is one of the high-speed forming processes using electromagnetic force. Fine and sharp details of the product can be obtained, and springback after deformation is extremely reduced in comparison to the conventional forming processes(Psyk, Risch, Kinsey, Tekkaya, & Kleiner, 2011). Figure 1 shows a schematic diagram of MPF. A metal sheet is placed over the coil in the discharge circuit. The discharge current runs through the coil, and magnetic fieldis producedaround the coil. An eddy current is inducedin the metal sheet. Interaction between magnetic field and eddy current creates electromagnetic force. The metal sheet accelerated by electromagnetic forcecollides ontothe mold. Forming is completed in a few tens of micro-seconds.MPF is suitable for metals with a high electrical conductivity like Al and Cu.The MPFed metal may have characteristic microstructure because of high strain rate deformation."

Jan 1, 2018

By J. L. Furtney, C. Fairhurst

"Although global mineral resources are considered to be adequate to meet the needs of a rapidly growing world population, the United States is becoming increasingly dependent on imports. This could have implications for both the economy and national security. The US is a country with a strong tradition of leadership in science and technology. Impressive advances in autonomous underground mining systems reduce the adverse effects of heat and humidity in deep mines and focus renewed attention on ground control. Developments in computing power open opportunities to develop improved understanding of the important role of discontinuities (faults and fracture systems) and more effective design of deep excavations. Establishment of mining R&D Centers at leading US research universities, jointly funded by industry and US federal agencies is recommended as an effective step for the nation to remain an influential partner in world mining. INTRODUCTION. “None of the arts is older than agriculture, but that of metals is no less ancient.. . for no mortal man ever tilled a field without implements. If we remove metals from the service of man, all methods of protecting and sustaining health and more carefully preserving the course of life are done away with.” Agricola (1558)i Homo sapiens, generally acknowledged as the species from which modern Man has evolved, is considered to have originated in Swaziland some 100,000-200,000 years ago. Evidence of use of minerals in that region has been dated to earlier than 40,000 BC.ii Today, a large fraction of the elements of the Periodic Table are derived from minerals, and finding new applications in development of innovative technologies. Agricola’s comments are as applicable today as ever.iii Metals such as copper, tin, lead, iron and aluminum were mined and smelted several thousands of years BC. It was not until the Industrial Revolution, started in the latter half of the 17th Century in Northern England, where coal was available as an energy source, and iron as the basis for fabricating machinery, that dramatic change to society began to occur. Human toil was replaced by far more powerful machines. Rural communities migrated to work in factories in urban areas. Rapid transportation over long distances became possible, leading eventually to the world of today. The change spread to other parts of the world, bringing wealth and power. Although now well established in some regions, the Revolution has still to arrive in many other parts of the world. This can be seen in Figure 1, which shows the relative wealth, or ‘Standard of Living’ as measured by the GDP/capita, of regions around the world. Regions such as North America, Europe, and Australasia iv are seen to have the highest standard. Thanks to today’s global communications systems, regions with relatively low GDP/capita are well aware of ‘how others live’ – and eager to emulate them."

Jan 1, 2018

By Yuhua Wang, Haitao Zheng, Guangli Zhu, Yuehao Zhao, Fushun Yu, Dongfang Lu

"Spodumene, feldspar and quartz possess similar surface properties, which make the difficult to separate spodumene from other silicate minerals by flotation. The differences of crystal structure, surface property and floatability of three minerals were studied by various technical means. The results show that Li-O and Al-O bonds in spodumene structure are not strong and easy to be broken. However, Al-O and Si-O bonds in feldspar and Si-O bond in quartz are very strong and not easy to be broken. High contents of Al and Li on spodumene surface were found by XPS measurements, which is benefit for the adsorption of anionic collector. The surface energies of main cleavage planes of spodumene (110), feldspar (001) and quartz (001) are 1.88 J/m2, 2.97J/m2 and 2.68J/m2, respectively. Hence, the exposed surfaces of feldspar and quartz are not saturated and easy to adsorb OH- ions from solution and cause the lower IEP than spodumene. The contact angles of three minerals in water are lower than 16º, suggesting that the hydrophilicity of three minerals is high, and the order of hydrophilicity is quartz > feldspar >spodumene. Correspondingly, contact angles and flotation recoveries of spodumene are bigger than that of feldspar and quartz in presence of a combined anionic and cationic collector named YOA.INTRODUCTION Flotation technology plays most important role for the recovery of spodumene from pegmatite ore. Generally, spodumene with fresh surface is easy to be floated using soap and oleic acid as collector, and the best flotation pH range is 4.0 to 9.0. However, the flotability of spodumene will become worse when its surface was polluted by slime which produced by the weathering of spodumene and other silicates (Dresler et al. 1998; Moon and Fuerstenau 2003; Menéndez et al. 2004; Yu et al. 2015). In addition, the species of Ca2+, Fe3+, Mg2+ and other metal ions in pulp can not only activate the flotation of spodumene, but also the activation of gangue minerals, and then the flotation selectivity of spodumene from gangue minerals became wores (Wang and Yu 2007; Yu et al. 2014). In order to eliminate the negative effects of slime and metal ions on the flotation of spoddumene, the desliming and long time scrubbing with the addition of NaOH and Na2CO3 were adopted. Usually, NaOH shows the activation for spodumene flotation, and the recovery of spodumene increases with the increase of NaOH dosage. Na2CO3 can eliminate the non selective activation of Ca2+, Fe3+, Mg2+ ions in the pulp, and the concentrate grade of spodumene increases with the increase of Na2CO3 dosage. Anionic collectors such as chelants, hydroxamic acid, oxidized paraffin soap, naphthenic acid and oleic acid were widely used for the flotation of spodumene (Dresler et al. 1998; Moon and Fuerstenau 2003; Menéndez et al. 2004; Yu et al. 2015)."

Jan 1, 2018

By Ye Chen, Jianhua Chen, Meng Liu, Yuqiong Li, Xiao Mu, Cuihua Zhao

"Sulfidization-amine is the most effective method for the recovery of smithsonite (ZnCO3), however the interface interaction details remain unclear. The sulfidization-amine flotation mechanism of smithsonite has been studied by Density Functional based Tight Binding (DFTB+) method in this paper. The slab model of ZnCO3 (101) surface was built and the adsorptions of a monolayer of HS- and S2- ions were conducted to model the sulfidization effect on the ZnCO3 (101) surface adsorption. DDA hardly interacts with the hydrated ZnCO3 (101) surface. Under the low concentration of Na2S, HS- ions form a Zn-SH-SH structure on the ZnCO3 (101) surface, which hinders the interaction between DDA and surface Zn atoms. Under the high concentration of Na2S, a layer of ZnS is formed on ZnCO3 (101) surface, which is favorable for the adsorption of DDA on the surface. This is consistent with the flotation practice where smithsonite flotation requires a large amount of sodium sulfide. The results could provide a microscopic investigation into the sulfidization-amine flotation mechanism of smithsonite.INTRODUCTIONSmithsonite (ZnCO3) is an important and typical oxide mineral of zinc. It is a semi-soluble salt mineral with a solubility product constant of 1.46 × 10-10 (Weast, 1973). The most common and effective method to recover oxidized zinc ores is froth flotation (Caproni et al., 1979; Pereia and Peres, 2005; Kashani and Rashchi, 2008). It is well known that the flotation of oxidized zinc minerals is much more difficult than the flotation of zinc sulphide minerals (Hosseini and Forssberg, 2007).The recovery of zinc oxide ores with poor floatability attracts more and more attention due to the depletion of easy-recovered of zinc sulfide ores.Sulfidization-amine flotation, which using Na2S as sufidizing agent and amine as collector (Mckenna et al., 1949; Rey, 1954; Abramov, 1961; Rey, 1979; Hosseini and Forssberg, 2007). This method is the most successful technology used for zinc oxide minerals flotation in large-scale industrial applications since it was invented in the 1950s (Önal et al., 2005; Pereira and Peres, 2005). There have been numerous experimental researches on the sulfidization-amine flotation of smithsonite. Shi et al., (2013) studied solution chemistry of smithsonite flotation system. Feng and Wen (2017) studied the formation of zinc sulfide species on smithsonite surfaces and its response to flotation performance. Wu et al., (2017) investigated the sulfidization behavior of smithsonite with the use of zeta potential, inductively coupled plasma (ICP), scanning electron microscope (SEM), and X-ray photoelectron spectroscopic (XPS). Their measurement results confirms the chemisorption of sulfur ions and the formation of ZnS film on the smithsonite surface after Na2S treatment, however the influence of HS- ions on the surface and the influence of sulfidization on the amine adsorption have not been discussed."

Jan 1, 2018

By Erik Westman, Benjamin Mirabile

"Quantitative evaluation of secondary support performance in longwall tailgates in U.S. coal mines was introduced with the U.S. Bureau of Mines (USBM) Wood Crib Performance Model. This model evaluated crib performance based on load capacity, stability, and convergence characteristics. The introduction of a large variety of alternative secondary supports in the 1990s prompted a full-scale load-displacement testing program conducted by the USBM and, subsequently, NIOSH. The application of the ground response curve concept to secondary supports provided a more complete estimation of secondary support loading in longwall abutment zones. Secondary support loading from floor heave, horizontal stress effects, and pillar yield are captured by the ground response curve. A point on the ground response curve can be measured by instrumenting a secondary support with load and convergence measurement devices. A segment of the ground response curve can be measured by instrumenting two secondary support types of varying stiffness. Numerical models have been used to construct complete ground response curves for longwall tailgates based on measured secondary support performance. The ground response curve concept can be used as a design methodology for secondary supports in the #2 entry, as well as the longwall tailgate. Extending published evaluation and design methodologies for secondary support in longwall tailgates, a ground response curve unique to the loading conditions and required functionality of the #2 entry can be developed. Numerical models can be used to construct full ground response curves based on measured data in the #2 entry.INTRODUCTIONA longwall ventilation system is designed to continuously dilute and move methane-air mixtures and other contaminants from the active face, to bleeder systems, and out of the mine. The #2 entry of the tailgate gateroad serves to transport contaminated air from the longwall face to the bleeder system. The #2 entry is required to function as an air course between two longwall gobs and is subject to significant ground movement and loading. Current ground support design and evaluation practices are based on empirical evidence and little to no quantitative data on support performance exists for these entries. Substantial volumes of research have been conducted on ground movement and support performance in longwall tailgate entries. Following the successful ground support evaluation and design practices established for longwall tailgate entries, a practical and efficient design methodology can be adapted for supporting the #2 entry of a three-entry gateroad system."

Jan 1, 2018

By Jie-Liang Wang, Yongdan Cao, Zhao Cao

"The effect of ethylenediamine tetraacetic acid (EDTA) on flotation separation of fluorite from bastnaesite and its selectively depression mechanism on fluorite were studied by single mineral flotation, artificial mixed minerals flotation, solution chemistry analyses, Zeta potential and XPS measurements.The results show that fluorite can be deeply depressed by EDTA while the flotation of bastnaesite is almost unaffected when octanohydroxamic acid (OHA) is used as a collector. The separation index (SI) between bastnaesite and fluorite increases with the dosage of EDTA, SI can be raised from 1.18 to 12.66 when EDTA dosage increases from 0 to 2×10-3mol/L.Solution chemistry analyses show that EDTA is able to convert the Ca(OHA)2 hydrophobic precipitation on fluorite surface to a soluble Ca-EDTA complex but cannot complexly dissolve the Ce(OHA)3 precipitation on bastnaesite surface. Therefore, the Zeta potential of OHA conditioned fluorite can be reduced significantly by EDTA while the reduction degree to Zeta potential of bastnaesite is relatively low. XPS measurement shows that EDTA removes the chemically adsorbed OHA from fluorite surface but has little effect on the adsorbed OHA on bastnaesite surface. As a result, fluorite can be selectively depressed by EDTA in bastnaesite flotation, which behaves an important industrial application prospect in rare earth ore flotation.INTRODUCTIONNowadays, Rare earth elements (shortened as RE) and compounds are of significant importance for a range of rapidly expanding industrial applications including catalysis, metallurgy, renewable energy, and special materials due to their unique electrical, magnetic, optical and chemical properties [1]. The seventeen RE elements, including the lanthanide-group fifteen elements, yttrium and scandium, could be divided into three groups, i.e., light, medium and heavy RE elements based on the different solubility of RE sulfates [2]. Bastnaesite ((Ce,La)CO3), containing approximately 75% REO, is one of the most important light RE minerals [3]. Flotation is the common method to recover basetnaesite [4-6]. Nonetheless, basetnaesite is often associated with calcium-bearing gangue minerals such as fluorite, and the separation of basetnaesite and fluorite by flotation is usually difficult due to their similar surface properties and therefore floatability [7-9]. Therefore, research on high selective flotation reagents of bastnaesite over gangue minerals has attracted a lot of attention [10]."

Jan 1, 2018

By Yonghui Hu, Hongxiang Ran, Honggang Wei

"A new PVM vertical ring high-gradient high-intensity permanent magnetic separator authorized by China Invention Patent ZL201110294866.4, which featured with vertical magnetic field structure was developed to dramatically save energy consumption and running costs compared with electromagnetic separators. The specific magnetic circuit design ensures PVM separator generating high magnetic field intensity as well as solving equipment large-scaling. The newly developed industrial PVM separator has been proved suitable for recovery of weak magnetic minerals or purification of non-metallic minerals benefiting from its high background and induction magnetic field intensity up to 0.8/1.5T, stable service performance and low running costs. The first ?1.5mm PVM separator has been applied in removing iron from quartz sand in Fengyang, Anhui, and ?2mm PVM separator will be installed to separate hematite. Industrial applications and tests proved that PVM separators could gain similar separation effects and especially save more than 80% of power consumption compared with the conventional electromagnetic high-gradient high-intensity magnetic separator, which will contribute a lot for energy conservation and environmental protection. The development of high gradient magnetic separator technology has played an important role in utilizing weak magnetic minerals, which has been widely used in many mining enterprises. The main forms of high-gradient magnetic separators include both of electromagnetic high-gradient and permanent magnetic high-gradient. The vertical ring high-gradient high-intensity permanent magnetic separator features with high magnetic field gradient, large processing capacity and never clogging, which has been widely used in recovering fine weak magnetic mineral and purification of non-metallic minerals[1-3]. However, electromagnetic coils excitation needs more energy consumption, and relatively high running costs and maintenance costs as a result of the complicated cooling system. So permanent magnetization of the electromagnetic magnetic separation equipment is a very important research direction at present. With the continuous improvement of resource utilization standard and efficiency requirements, high energy consumption of the electromagnetic vertical ring magnetic separator have been highlighted, which has affected the economic benefits of mining enterprises to a certain extent. In the aspect of high-gradient high-intensity permanent magnetic separation equipment, considerable researches have been carried out at home and abroad and many small-sized prototypes were developed yet never strode into large-scale industry applications[4-6]."

Jan 1, 2018

By Xubo Chen, Zhiqiang Hu, Zhijian Sun, Gaoyun Zhou

"The research aimed at developing an efficient and environmental frother,which was applied in the flotation of sulfide ores. The flotation properties of an efficient frother and pine oil have been studied relatively by flotation tests of lead and zinc sulfide ores. At the same time, the biodegradability of two kinds of frother has been studied by the method of biological respiratory curve. The test results show that the flotation properties of new frother are superior to pine oil such as flotation rate, dosage etc. and its biodegradability is superior to pine oil. INTRODUCTION Frother is a kind of important agent in flotation reagents.In practice, the criterion of the foaming performance of the frother is what is high and low according to flotation indexes. The difference of different minerals and flotation technologies has great influence on the foaming performance of frother, and it is very important to choose the corresponding frother. The type, dosage and selectivity of frother in flotation process must be considered carefully. In today's society, environmental protection and ecological protection are becoming more and more important, and the environmental and ecological damage from mine development has aroused increasingly more attention. The use of mine agents has promoted the development of mineral resources, greatly improves the recovering utilization of mineral resources, at the same time, the production and use of mine reagents also inevitably bring about pollution, and result some influence or damage in the ecological environment.The frother is a common kind of reagent in the flotation process of the concentrator. In many cases, the waste water in the concentrator can not be let out in the natural water because the higher content of the frother in the waste water results in higher index of COD.This will inevitably increase the cost of waste water treatment in the mine.Therefore, the choice of frother should not only consider its influence on the flotation index, but also consider its influence on environmental protection. Waste water treatment is a way to solve the waste water pollution, but it needs to cost a lot of fund, manpower and material resources.And the development of high efficiency pollution-free reagent is a good way to reduce the production cost of mining enterprises and reduce the environmental pollution."

Jan 1, 2018

By A. V. Abshilawa, D. G. Talakhadze, R. I. Sturua

"Processing of the tailings accumulated over the lifetime of Madneuli Copper Concentrator is an opportunity to extract additional salable copper and gold products. This paper presents a pre-concentration process for the valuable components (copper and gold) of the accumulated tailings. The developed process makes it possible to obtain a copper pyrite concentrate with a yield of 14.05%, copper grade of 1.36%, and recovery of 83.22% containing 3.78 g/ton of gold at a recovery of 84.31%. The bulk concentrate is produced by a combined process bringing together selective flotation to produce salable copper concentrate and hydrometallurgical processing of the selective flotation tailings to recover gold. KEYWORDS: FLOTATION, ALBION PROCESS, LEACHING, COPPER CONCENTRATE, SELECTION Madneuli Copper Concentrator, Georgia, was put into operation in 1975. Over its lifetime, 40 mn tons of tailings have been accumulated at the tailings storage facility (TSF). Sampling of the TSF has indicated that the average copper and gold grade is 0.23% and 0.56-0.65 g/ton, respectively. Accordingly, the TSF can be classified as a technogenic reserve. This paper discusses pre-concentration of valuable components using flotation, followed by processing of the bulk concentrate in the Albion process. Mineralogical analysis of the accumulated tailings showed that the main ore mineral is pyrite (11.71%). Copper minerals are mainly represented by chalcopyrite (0.7%). The main nonmetallic mineral is quartz (67.3%); sericite, chlorites, etc. also occur. Pyrite is present both as liberated grains and intergrowth. The absolute majority of copper minerals are found as intergrowth with pyrite, less often with quartz. Ore minerals are slightly oxidized. Chemical analysis results are shown in Table 1. Particle size distribution shows that the size class -0.2 mm - 0.045 mm has the highest grade of 0.85 to 0.97 g/ton of gold. Size class +1.25 mm has the lowest grade. Based on the chemical and mineralogical studies and particle size distribution, an optimized process was developed for pre-concentration of the valuable components prior to hydrometallurgical processing. Several gravitation, direct selective, bulk, and bulk selective flotation processes were trialed. (1,2)"

Jan 1, 2018

By Brian Loveday, Sandile Nkwanyana, Indresan Govender

"Recent batch experiments by the authors in a pilot scale ball mill (Ø = 0.6m) have demonstrated that a partial replacement of the ball charge by pebbles (25 % pebbles; 75 % steel balls) optimally reduces the ball and power consumption without altering the rate of production of fine material (passing 75 microns). At higher pebble volumes, the production rate of fines was reduced progressively. With the 25/75 composite charge a saving of 13 % in power consumption was achieved, and a saving of 25 % in steel ball consumption is implied. A partial replacement of steel balls by pebbles reduces the overall density of the grinding media in the charge. Taking into consideration that the production rate of fines is usually proportional to the bulk density of the charge in the mill, it would be expected that a composite charge (e.g. 25/75) would coarsen the grind and consequently reduce the rate of production of fines. Pebble wear contributes a small proportion of fines and it doesn’t provide a full explanation of why the 25/75 composite charge has no (or minimal) adverse effects on the rate of production of fines. Clearly, the production of fines across the mill is directly related to the shear and compressive power dissipation density. Accordingly, we hypothesise that the spatial power dissipation distribution meeting the minimum requirements for fines production— at the so-called active regions—are equivalent, or minimally comparable, for both the 25/75 composite and 100 % ball charge operating conditions. To test the hypothesis, we performed DEM simulations to analyse power dissipation in the active regions. 1. INTRODUCTION Comminution remains to be the most expensive process in mining operations, particularly because the energy consumed in this process accounts for 30-70 % of the total cost of a mining operation (Nadolski et al, 2014). Optimization of comminution circuits has been focussed on reducing capital and operating costs and maximising throughput capacity. For existing operations, it is often a challenge if the optimization process recommends retrofitting new ‘major’ equipment. The challenge arises from new capital cost and the difficulty of retrofitting in an existing circuit, while maintaining production (Major et al, 2001). Thus, for existing mining operations, optimization of comminution (cost and throughput) is often limited to operating conditions and/or addition of auxiliary equipment (such as pebble crushers, additional screens and high pressure grinding rolls (HPGR)) (McIvor and Greenwood, 1996; Hart et al, 2001; Powell et al, 2015b)."

Jan 1, 2018

By M. Stogran-Baker, E. Legault-Seguin

"Fluorspar mining in the St. Lawrence area of Newfoundland and Labrador began in the 1930s and ended in the mid-1980s. In 2013, Canada Fluorspar (NL) Inc (CFI) discovered a new ore body, the AGS vein, which proved amenable to more economic open pit mining methods and began developing this resource. This paper discusses the flowsheet development of the AGS vein deposit. Testing at SGS began in 2009 with samples from other deposits in the area. The testwork included pilot-scale dense medium separation (DMS), laboratory-scale flotation tests to develop the flowsheet and a flotation pilot plant. The more recent work that is presented here has been devoted to the AGS vein, and included a variability testing program that gave tremendous insight into the metallurgical drivers of processing the deposit. The ore was found to be fairly variable in terms of fluorite grade, but also gangue mineralogy, which had greater implications on the DMS performance. The gangue mineralogy was also found to significantly impact the grindability characteristics of the DMS product. This paper will detail the testing conducted and the mitigating steps which were identified for the operation.INTRODUCTION Fluorspar is the industrial trade name for the mineral fluorite (CaF2), which is the primary industrial source of fluoride. There are a number of categories of fluorspar, most notably acid-grade fluorspar and metallurgical fluorspar (metspar). Acid-grade fluorspar has stringent specifications and is suitable for the production of hydrofluoric acid that is used for many applications. The typical specifications of acid-grade fluorspar are >97% CaF2 and less than 1% each of SiO2 and CaCO3, with a particle size distribution in the order of 80% passing 100 µm. Metspar is typically used for metallurgical purposes, typically as a flux in smelting, and has significantly more relaxed specifications (< 15% SiO2). The principle source of fluorspar in Canada has been from the Burin Peninsula in Newfoundland and Labrador. More than 3 million tonnes of fluorspar were produced there between 1940 and 1978 and from 1987 to 1990, when production ceased (Fulton & Montgomery, 1994)."

Jan 1, 2018

By M. Gonzalez Fernandez

"If the final goal of metallurgy is the extraction of metals from a given ore, everyone knows that this achievement relies on many separation steps involving much more than a biphasic material made of metal and gangue. Nevertheless, still today, most of the design and follow-up of industrial processes only consider metal grades; in best case metal grades per size class. Working with such heterogeneous material, made of several minerals, with different grain size and texture, implies to consider finer ore models to be able to predict the behavior of material and the subsequent operation performances. Analytical tools are now available to provide such relevant and accurate data which are applied in geometallurgy. To achieve a true geometallurgical approach for process design, but also for optimization, accurate process simulation absolutely needs to combine these fine ore models with the corresponding unit operation models. Based on generic, but configurable, criteria of description and a hierarchical approach, the material modelling tool embedded in the USIM PAC process simulator provides the necessary flexibility to describe any type of ore with almost no limit in the level of details and associated physical properties that can be met in the mining industry. The simulation engine and the mathematical models of unit operations are designed to manage such a diversity of material modelling. The paper present various ore models and some of their applications in flowsheet simulation. It proves the interest of this detailed and advanced approach to accurately predict plant performances. INTRODUCTION Process simulation used for process design and optimization requires accurate unit operation modeling. During the last decades, main efforts of the different teams developing software simulators have been dedicated to those models for comminution and physical separations such as flotation or gravity concentration (Kojovic et al., 2012, Soni and Yoon, 2014). In most case, the ore is modelled with a size distribution and metal or mineral grades. A water phase is considered for wet processes. The association of unit operations and such material models generally allows, after some parameters adjustment, to achieve good agreement between experimental and simulated data. The use of the obtained simulator to test alternative configuration of circuits or settings of equipment devices can be accurate enough as far as the ore processed is close to the ore used for simulator adjustment. However, when the ore gets very different grades, coming from different mineral proportions or grain sizes, the simulation results can be of poor accuracy. Because any physical separations such as gravity, magnetic or flotation, do not sort metal and gangue but particles, made of minerals, containing metals, the only way to be accurate enough for allowing extrapolations, is to model particles. The phase model tools embedded in the USIM PAC process simulator gives this possibility. However, as such level of details are not always available for analyses, the tool has been designed with a high level of flexibility, to adapt the model to the available data. In this paper, the principles of this conceptual modelling tool are presented, and some application cases illustrate the material model flexibility and its interest."

Jan 1, 2018

By T. K. Akopyan, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"A qualitative and quantitative analysis of the new Al-Ca-Mn-Fe phase diagram in the region of the aluminium corner is carried out using both thermodynamic calculations and experimental methods. Using the obtained data, the principal possibility of creating both cast and wrought sparingly alloyed aluminium alloys with calcium, manganese, scandium and zirconium at allowable iron contents of up to 0.4% that do not require solution treatment and quenching is justified. At the selected concentrations, the entire amount of manganese (1%) is practically included in the aluminium matrix, while calcium (~2%) and iron are in the multiphase eutectic, which has a fine structure. The joint introduction of 0.25% Zr and 0.1% Sc into the alloy leads to precipitation hardening due to the formation of the L12-Al3(Zr,Sc) phase during annealing. Based on the experimental data for the model multicomponent Al2CaMnFeZrSc alloy, it is shown that such alloys can combine high mechanical properties and good manufacturability during both casting and metal forming. This is due to the combination of a narrow temperature range of solidification with a fine eutectic structure.INTRODUCTION Hardening in branded aluminium alloys (both cast and wrought) is generally achieved by heat treatment of the T6 type, including quenching and artificial aging (Zolotorevskiy, 2007; Kaufman, 2004; Mondolfo, 1976). Heat treatment significantly increases the cost of the final products. Therefore, industrial companies are interested in developing alloys that can be hardened to the desired level without quenching. To solve this problem, alloys with scandium are the most suitable (Toropova, 1998; RØyset, 2005). This element (usually in an amount of ~0.3%) is one of the most effective hardeners in aluminium alloys, due to the formation of Al3Sc (L12) phase secondary precipitates, the size of which is less than 10 nm (Knipling, 2010; Fuller, 2005). These nanoparticles are formed during the annealing via decomposition of the supersaturated aluminium solid solution (hereinafter referred to as (Al)). This feature allows us to significantly increase the strength of aluminium alloys by simple annealing (at ~300°C), i.e., without heat treatment, including quenching. However, scandium is a very expensive metal, so its use as an additive is severely limited. The most effective method is the introduction of scandium together with zirconium (Lefebvre, 2009; Booth-Morrison, 2012). The optimal combination is the introduction of ~0.1% Sc together with 0.20–0.25% Zr, which, according to (Belov, 2006), gives approximately the same strengthening effect as the introduction of 0.3% Sc."

Jan 1, 2018

By I. V. Makarskii, D. N. Nikitin, L. G. Tarasova

"The extent and nature of the damage to diamonds at processing plant is largely determined by the design features of the equipment, the characteristics of the feed ore and the parameters of the ore disintegration process (change in the rotational speed of the autogenous mills, variations of the water supply to comminution process, choice of the optimum charge, etc.). To monitor the intactness of diamonds, an instrumental method using the X-ray tomography system and colored synthetic indicator diamonds was developed for identifying the process-related damage. The X-ray tomography system consists of a CT-Portable X-ray tomographic scanner, a crystal positioning device and customized software (developed by the Fraunhofer Institute and Aliud GmbH, Germany). The developed method enables improvement of the accuracy of the results, exclusion of the subjectivity of the mineralogical assessment, acceleration of data processing and promptly planning of the activities aimed at reducing the process-related damage to diamonds. KEYWORDS Diamonds, colored indicator diamonds, process-related damage, loss of mass, instrumental method, X-ray tomography system. INTRODUCTION Industrial tests of ore processing technology at the enterprises of ALROSA PJSC are accompanied by assessment of the process-related damage to diamonds. The assessment of the process-related damage to crystals is carried out for prompt elimination of factors contributing to the increase of impact forces in the process flow sheet of ore treatment plant. For this purpose a specially selected parcel of -4.0 + 2.0 mm sized natural indicator diamonds is used. The diamonds are exposed to ionizing radiation in order to turn them green and thus to create a distinctive feature. Colored natural indicator diamonds are described, photographed in several views and introduced into the process flow sheet of the processing plant, then extracted from the process flow, described and photographed again. The comparison of diamonds before and after their passing through the process flow sheet of the plant allows to find evidence of process-related impact on the crystal and to calculate the factor of process-related damage (the number of crystals damaged during liberation and recovery), the loss of crystal weight and the degree of damage to the crystals. The method of colored indicator diamonds is used to select processing methods, equipment or regime which would be the safest for diamonds based on the analysis of the factors of process-related damage. There are limitations of the method, such as:"

Jan 1, 2018

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By Teja Reddy, Narasimha Mangadoddy, Mandakini Padhi

"In mineral comminution circuits, the feed to hydrocyclone consists of a heterogeneous mixture having varied degrees of liberation and sizes leading to the multi-component particle system. The presence of multicomponent particles exhibits a significant change in the classification performance parameters. In this work, a numerical study is conducted with an artificial mixture of magnetite and silica of different proportions having similar particle size distribution to understand the multicomponent interaction in a laboratory scale hydrocyclone. The heterogeneous feed is injected tangentially would attain different settling rates under the influence of centrifugal, drag and turbulent dispersion forces. In this work, Large Eddy Simulation (LES) is used to resolve the continuous phase turbulence. Modified Algebraic Slip Mixture (ASM) model using the corrected Newtonian rheology of fines to simulate multi-density and multi-size particles of the mixture in a hydrocyclone. The influence of the multi-component particles on classification performance is extracted from the simulation in terms of the performance curve, i.e. recovery to underflow, volume fraction distribution and the key forces acting on each particle in the mixture. An interaction was observed between different components during the classification process, featuring accumulation of heavier particle at wall-side pushing the lighter particles into the inner locus of zero vertical velocity (LZVV) zone. The comparison of separation factors of different size particles presented the higher probability of the magnetite of same size reporting to wall region and hence to underflow. Hence, an increased component cut-size with the increased magnetite proportion, particularly a profound effect on lighter density component’s cut-size was observed. INTRODUCTION The multicomponent existence is found in naturally occurring ores, affecting the pure metal extraction, nonetheless also affects the comminution and classification processes. Among many another classifier, hydrocyclone is a vital equipment used vastly in many industries. The main advantages over other classifiers are a static body, low operating cost and maintenance, high throughput, low floor space requirement etc. A typical hydrocyclone consists of a cylindrical section with a central tube connected to a conical section with a discharge tube. The fluid is injected tangentially into hydrocyclone causes swirling and thus generates centrifugal force within the device. The multiphase interaction inside the hydrocyclone is extremely complex and mostly explained by theories based on hypothesis. In past years, many theoretical models were proposed like a balanced orbital model (Criner, 1950), the residence time model (Reitema, 1961) etc. Though these models give an estimation of the cut-size and other performance parameters, it cannot predict the accurate performance of the actual state of operation. Among these models, the balanced orbital theory is the most adapted concept, based on the force balances of the particle in the dual vortex flow of hydrocyclone. The finer particle is subjected to the inward drag force, generated from the outer vortex flow to the air core, and drags the particle towards the overflow. The larger particle with the higher mass have enhanced centrifugal force and falls into primary vortex near wall reporting to the underflow. Generally, the forces acting on the particle include the drag force, centrifugal force, pressure gradient force, added mass force, Saffman lift force, Magnus force and basset force (Kraipech, 2005). The major forces like a drag, centrifugal, pressure gradient are the function of the particle properties like the size and the density. Hence, the existence of the multi-size and the multi-density particle will affect the separation phenomenon, with the varied forces acting on it. The understanding of the multicomponent classification effect using ores has been only explored in few studi"

Jan 1, 2018

"The most common agglomeration technique in iron and steelmaking is sintering, which requires the use of iron ore/concentrate mixtures, limestone and dolomite as fluxes and coke as fuel in order to produce the required melt at high temperature to cause agglomeration of the particles. Sinter feed blends containing high proportions of magnetite concentrate are difficult to granulate and to produce granules of high permeability, and sufficiently robust quasi-particles for successful sintering operations. Since the granulation of iron ore sinter feed requires no use of a binder, the added fluxes play a vital role in holding the granule particles together until they sinter. The fluxes also help to improve the granule quality and control slag composition in the blast furnace. It is well-known that the particle size distribution of the fluxes affects the granulation effectiveness and green bed permeability which determine the productivity, physical and metallurgical properties of the granules and sinter. Hence it is necessary to understand the role of flux particle size on granule properties so as to improve the granulation of iron ore sinter feed blends containing high magnetite concentrate. In this study, laboratory granulation experiments have been carried out on iron ore sinter feed blends containing high proportions of magnetite concentrate at different addition levels of limestone and dolomite mean particle sizes, to understand the influence of limestone and dolomite particle sizes on granulation rate processes and granule properties.INTRODUCTION Increases in iron ore production to meet the global demand for iron and steel products has led to the depletion of high grade iron ores and thus the current utilisation of low grade iron ore fines and concentrates. However, sinter, pellets and the lump are the required feed types used in the blast furnace. The high basicity sinter is the main iron bearing feed accounting for 70-85% in the blast furnace due to its good metallurgical and mechanical properties that allow high productivity, efficient processes and low production cost (Adam et al., 2017)."

Jan 1, 2018