Search Documents

By K. V. Raj, A. Miller

"Workers at mineral processing facilities are often exposed to high levels of dust generated when ores are processed. Crushing, grinding, screening, and other processes generate large quantities of dust, which can exceed the threshold VALUES (prescribed by the Mine Safety and Health Administration (MSHA). Many ores contain quartz (silica), which has been known to cause serious health problems in workers over time. Given the structure of mineral processing plants, the airflow regime is not coherent inside the building, which may lead to multiple recirculation zones. These recirculation zones can trap dust, and concentrations of dust can then rise over time. Therefore, there is a need to understand the airflow phenomenon that occur inside of mineral processing facilities and how these occurrences interact with the dust generation processes to identify zones of potentially high dust concentration. Computational fluid dynamics (CFD) modeling can give a better understanding of the airflow and help recommend designs and methods to mitigate the high dust concentrations in a mineral processing plant. This paper presents the CFD modeling of airflow inside of a mill building to demonstrate airflow patterns that will affect the generation and subsequent dispersion of dust due to crushing, grinding, and other activities. This study was conducted by researchers from the National Institute for Occupational Safety and Health (NIOSH). INTRODUCTION In a mineral processing facility, minerals go through various mechanical processes in order to reduce their size for separation of economic minerals from gangue minerals to produce a final marketable product. This research, conducted by the National Institute for Occupational Safety and Health (NIOSH), focuses on ore mills in metal and nonmetal mining (MNM) operations, but the applicability of the approach will be valid for any large structure where workers are exposed to airborne contaminants. The processes of crushing, grinding, cleaning, drying, and product sizing in these facilities generate a large amount of dust, creating hazardous conditions for the workers in these facilities. This is highlighted by the fact that MSHA sampling data for the years 1997–2012 indicate that 12.3% and 15.9% of the gathered samples were over 100 µg/m3 for silica for metal and nonmetal mills, respectively [1]. Mineral processing operations typically use some type of engineering control to address their most significant dust sources. Engineering controls include such approaches as bag-house-type dust collectors, scrubbers, and electrostatic precipitation [2]."

Jan 1, 2018

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By H. Hamza, M. R. MacIver, M. Pawlik, L. Malin

"Size and shape are important properties of aggregates formed in engineering processes and natural systems. Measurement of aggregate size or shape is a challenge when the solids concentration is beyond the gel point, ?? > ??g, when the aggregates are in contact and it is difficult to distinguish or segment individual particles in the network. This paper describes the use of a micro-computed tomography (micro-CT) method for the calculation of the aggregate volume fraction, ??, and a characteristic aggregate length, ??a, based on a 3D chord length measurement algorithm. These parameters can be used to quantify changes in aggregate and pore size during a compressive yield stress test to help understand the impact of flocculation and network structure on dewatering. INTRODUCTION In a thickener, flocculation is often used as a pre-treatment step and the final solids content of the underflow depends on the network strength and permeability of the bed formed by settled aggregates (Usher, Spehar, and Scales 2009). This paper describes the measurement and analysis of micro-computed tomography (micro-CT) of flocculated mineral sediments to obtain a characteristic length, ??a, of the aggregate and pore phases during a staged compressive yield stress experiment. This parameter may be used as an indicator of changes in aggregate and pore size to quantify material behaviour in solid-liquid separation processes that depend on self-weight compression or applied pressure. This analysis was carried out to help understand the effect of flocculation on aggregate structure and the thickening process as part of a broader research on the improved solid liquid separation of tailings produced in the oil sands industry.Aggregate properties The solids phase of an aggregated or flocculated suspension will eventually settle – if left undisturbed – under the influence of gravity. As settling of a flocculated suspension continues, the solids volume concentration, ??, may increase to the gel point or gelation threshold (Landman and White 1994), ??g, above which the aggregates form a network of touching particles, or space-filling structure (Kranenburg 1994). In the sediment bed, the aggregates are surrounded by fluid and occupy a partial volume fraction, ??, according to"

Jan 1, 2018

By R. Quentin Eades, Kyle Perry

"Surface mines continue to implement highwalls for several reasons, such as increasing recovery, improving margins, and justifying higher stripping ratios. Highwall stability is a complex issue that is dependent upon a variety of mining and geologic factors, and a safe design is necessary for a successful surface operation. To improve highwall stability, it is important to understand the connection between local geology and blasting.Explosives are employed throughout the mining industry for primary rock breakage. There are a number of controlled blasting techniques that can be implemented to improve highwall stability. These include line drilling, smooth wall blasting, trim blasting, buffer blasting, air decking, and presplitting. Each of these techniques have associated advantages and disadvantages. Understanding local geology is necessary for selecting the appropriate controlled blasting technique. Furthermore, understanding the limitations and conditions for successful implementation of each technique is necessary. A discussion of the impact of geologic conditions on highwall stability is provided. Additionally, discussion is provided for the successful incorporation of the controlled blasting techniques listed above, and the associated mining and geologic factors that influence the selection and design of controlled blasting plans. Finally, a new methodology is proposed.INTRODUCTIONExplosives are used throughout the mining industry as the standard for primary rock breakage, a critical part of the mining cycle. In 2015, the U.S.. consumed 2.2 million tons of explosives (Apodaca, 2015). The coal mining industry accounted for the majority of explosive consumption, accounting for approximately 63% of total explosives. The quarrying and nonmetal mining industries accounted for 12% of explosive consumption, and the metal mining industry accounted for 9% (Apodaca, 2015). This constitutes 84% of the explosives used in the U.S. However, the energy released during the detonation process is often in excess of that required to adequately fragment the surrounding rock (Jhanwar and Jethwa, 2000). This excessive energy, along with over confinement and poor blast geometry, will cause damage to the undisturbed rock mass beyond the intended boundary of the blast. This event is known as overbreak or back-break (ISEE, 2011)."

Jan 1, 2018

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By S. Sheng, Y. G. Huang, W. Chai

"Polyacrylamide (PAM) is a typically synthetic depressant and may be used as a depressor of pyrite. The modification of polyacrylamide may improve its physicochemical properties and performances. Sulfonated polyacrylamides (SPAM) with different sulfonation degree (SD) were prepared using sodium sulfite as the sulfonating agent, and the interactions of SPAM and pyrite were investigated by the adsorption experiment in this work. The adsorption tests of SPAM on pyrite were conducted as a function of sulfonation degree, pH value and contact time. Pyrite and SPAM were constructed and optimized through MS software. The interaction mechanisms of sulfonated polyacrylamide and pyrite were simulated by molecular dynamics simulations. The results show that the adsorption capacities of SPAM at neutral and weak alkaline conditions are higher than that at acidic and strong basic conditions. The high sulfonation degree favors the adsorption of SPAM on pyrite surface. The adsorption process can be described best by the pseudo-second order kinetic model. Molecular dynamics simulations show that the adsorption of sulfonated polyacrylamide on pyrite is better than that of polyacrylamide. Sulfonated polyacrylamide can be used as a potential depressant of pyrite with the main interacting mechanism of hydrogenbond force.INTRODUCTIONPyrite is the most abundant sulfide mineral and often associated with valuable minerals such as galena, chalcopyrite, sphalerite, molybdenite, gold, diaspore as well as coal (Forrest et al., 2001; Jaiswal et al., 2015; Maier and Dobiáš, 1997; Qiu et al., 2017; Xin and Liye, 2010). Froth flotation is the most popular method to remove pyrite from valuable minerals. Pyrite could be floated as the flotation concentrate either by its hydrophobicity or activation by metal ions (Chandra and Gerson, 2009). What is more, pyrite could be seperated as flotation tailing by adding highly selective depressants including inorganic and organic modifiers. Polysaccharides polymers and lignosulfonate-based biopolymers are common natural organic depressants (Deng et al., 2017; Mu et al., 2016). While the synthetic organic products have proved to be particularly versatile in terms of molecule tailing capability and controlled structures (Boulton et al., 2001a; Raffa et al., 2015)."

Jan 1, 2018

By Wei Sun, Chengwei Li, Zhiyong Gao, Yuehua Hu

"Grinding for mineral liberation is a prerequisite for a successful flotation separation. Different grinding media produce mineral particles with different morphologies and surface properties. In this study, the surface physicochemical properties of fluorite particles produced by ball and rod mills were systematically investigated through single mineral flotation experiment, wettability measurement, X-ray diffraction (XRD) test and scanning electron microscopy (SEM) observations. The XRD observations reveal that the surface exposure degree for both mill particles follows the order {111} > {110} > {100}. The difference lies in that the rod mill ones have a higher exposure of more reactive {110} and {100} surfaces, leading to a stronger interaction with the collector. The difference also leads to their higher elongation and lower roundness values of rod mill particles which are beneficial for the particle-bubble attachment by shorting the induction time. The wettability and flotation results show that the rod mill ones have a lower critical surface tension and a greater hydrophobicity when treated with the collector solution and accordingly perform a higher flotation recovery. This work, for the first time, revealed the importance of the exposure of crystal surfaces in determine the shape factors and reactivity of the mineral particles and will help provide guidance for optimizing flotation separation and particle surface modification. INTRODUCTIONFluorite (CaF2) is the most important source mineral for producing F-based chemicals and materials which are widely used in industrial, environmental, and medical fields [1, 2]. In ore deposit, there are two kinds of occurrence forms of fluorite mineral. Firstly, the fluorite mainly coexisted with the gangue minerals like calcite (CaCO3) and quartz (SiO2). Because of their similar density and fine-grained dissemination in ore deposit, ball mill grinding before flotation separation has been widely applied to produce relatively fine particles [3]. Secondly, the fluorite is often associated with other valuable minerals with higher relative density such as scheelite (CaWO4) and cassiterite (SnO2). Due to their obvious density differences and coarsely grained distribution in ore deposit, rod mill grinding before gravity separation has been usually used to produce more uniform particles and avoid over-grinding [4-6]. After the gravity separation, a flotation separation is also employed to beneficiate the fluorite [7]."

Jan 1, 2018

By Richard Mills

Autonomous Underwater Vehicles (AUVs) are proven technologies used across market segments for survey, exploration and environmental monitoring tasks. When coupled with other autonomous platforms or sensor packages AUVs become part of an holistic system approach to exploration and environmental assessment and monitoring. Recent developments have seen AUVs deployed remotely with instantaneous access to data via the cloud. Our goal is to deliver the capabilities of each of these elements and present a cohesive data set with automated processing tools over a cloud based interface. nmanned Technology AUVs The HUGIN AUV System is the most commercially successful AUV ever built. Operated as a single vehicle, or as part of a swarm, HUGIN’s area coverage rate is unrivalled. Equipped with a comprehensive sensor package including Kongsberg’s synthetic aperture sonar, it collects a data set. Some of these data are processed in-mission to enable operators to readily access it when the vehicle is recovered. HUGIN is well suited to mining survey and exploration. Capable of reaching 6000 metre depths and conducting missions greater than 60 hours, HUGIN collects seabed sonar imagery, sub-bottom profiles, laser and camera images plus environmental data, with sensors running concurrently.

Jan 1, 2018

By Yu. E. Emelyanov, A. V. Bogorodsky, R. N. Nabiulin, S. V. Balikov

"The paper describes the results of the study of gold-copper flotation concentrate atmospheric oxidation at different sizes of material, varying oxidation time, with air or oxygen blow. The study showed the low rate of sulphide oxidation during oxidation of flotation concentrate at a feed size (P98 -74 µm). The coppery recovery into solution was 48%; the recovery of gold by subsequent cyanidation reached 86%. Preliminary flotation concentrate grinding to P98 -20 µm provided oxidation of 90% of copper minerals, 80% of arsenopyrite and 15% of pyrite. The gold recovery by atmospheric oxidation of a fine-ground flotation concentrate increased by 59%, from 36% to 95%, the NaCN consumption reduced by 21 kg/t, from 30 to 9 kg/t. INTRODUCTION Processing of sulphide gold-copper ores and concentrates using conventional cyanidation technology results in higher reagent consumption and lower gold recovery. Destruction of sulphide minerals and extraction of copper from a processed product prior to cyanidation is essential for improving efficiency of precious metals recovery and reducing main reagents consumption. Atmospheric oxidation (AO) is one of the most promising hydrometallurgical methods of refractory gold-copper concentrates processing, along with biooxidation and pressure oxidation. The nature of this approach lies in oxidation of sulphides at 90-95°C, in acidic or alkaline conditions, with bubbling of oxygen or air, after preliminary ultrafine grinding (1-4). The following reactions of sulphide oxidation occur during atmospheric oxidation of a gold-copper flotation concentrate. Pyrite is oxidized with the formation of ferric sulphate (1) and elemental sulphur at low temperatures (2), whereas some portion of elemental sulphur reacts to form sulphuric acid: FeS2+3,75O2+0,5H2O=0,5Fe2(SO4)3+0,5H2SO4; ?G=-1144,02 kJ/mol (1)"

Jan 1, 2018

By A. V. Yevdokimov, Ye. V. Bogorodsky

The paper presents the results of the research on the development of gravity concentrates processing technology (gold grade is from 50 g/t to 1 kg/t and over) using intensive cyanidation with gold recovery to pregnant solutions followed by precipitation of metals from them using various methods. Test work and pilot plant results confirm that a new developed hydrodynamic regime provides an efficient treatment of gravity concentrates of polydisperse composition without their grinding and preliminary desliming. The resulting pregnant and washing solutions are amenable to metals recovery using electrowinning, cementation onto zinc dust and CIS. Cone plants with a lower ball valve for cyanidation of unground gravity concentrates developed by IRGIREDMET JSC have been successfully tested at a number of Russian operations. Currently, a modular plant equipped with gold electric precipitation from pregnant solution unit is successfully operated at a Russian gold processing plant. Cyanidation of the resulting high-grade gravity concentrate is carried out at the concentration of 8-10 g/L NaCN and 10 g/L NaOH. Gold recovery to the solution is 97-98%. Electrowinning is carried out in flow cell GNC-40M. In this case, the residual gold concentration yield is 0.3-0.5 mg/L. Also, a modular plant for relatively low-grade middlings (50-100 g/t Au) of gravity concentration has been introduced. The concentration of NaCN and NaOH is 2-3 g/L and 1.5-2 g/L, respectively, during leaching. This plant is equipped with a unit for gold cementation from pregnant solution with zinc dust. This cementation unit is of original design. It is made in the form of a filtering device and is composed of several layers of carbon fiber which contacts with zinc powder. The residual gold concentration yield from a cementation unit is less than 0.1 mg/L. Gold recovery is 93-97%. In 2017-2018, the introduction of intensive cyanidation modular plants to gravity concentrates will be planned at new projects of Russia and the CIS.

Jan 1, 2018

By S. Rupprecht

"INTRODUCTION This paper addresses the prevalence of poor public reporting practices of Coal Exploration Results, Coal Resources and Coal Reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or “saleable” tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal – therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (“ROM”) and Saleable coal tonnage, their associated qualities and other material and relevant information. Competent or Qualified Persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provide. “Companies are encouraged to provide information in their Public Reports, which is as comprehensive as possible” (CRIRSCO, 2013): too often this isn’t the case and material matters are either not reported or inadequately disclosed. According to the South African National Standard (SANS) 10320:2014 draft document - “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw Saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the Saleable Coal Reserve must be stated. The moisture basis of reporting shall be stated.” As an example to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are highlighted. The Kendal power station, commissioned in 1988, operates at a Calorific Value (“CV”) range of 19 to 20MJ/kg, an Ash content between 29 and 34% and Volatiles between 20 to 21%. Other power stations, such as Kriel or Hendrina, may require different qualities such as a CV range of 22 to 23MJ/kg, an Ash content between 20 and 28% and Volatiles between 22 to 23%. Thus, in terms of domestic saleable coal, it isn’t just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station” (Chetty, 2010). Sulphur content is also another important quality with the ideal coal content having a quality of less than 1% Sulphur."

Jan 1, 2018

By Bjørn Eske Sørensen, Kristian Drivenes, Przemyslaw Kowalczuk, Kurt Aasly, Gavyn Rollinson, Ben Snook

Efficient and successful mineral processing is dependent on detailed knowledge of the materials and minerals that are to be separated and concentrated. Common bulk methodologies such as XRD and XRF are fast and easy, and can provide an overview of the mineralogy and bulk chemistry of the material. However, they will not provide any textural information. Knowledge of the often intricate interaction between minerals in seafloor massive sulfide deposits is crucial in plant design for mineral processing. Samples from the Loki’s Castle hydrothermal vent have been characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), optical microscopy, Scanning Electron Microscopy (SEM), QEMSCAN, Electron probe microanalyzer (EPMA), and Electron Backscatter Diffraction (EBSD). Processing experiments used froth flotation and leaching techniques. The typical line of operation in ore characterization is shown in Figure 1. Mineral processing may be commenced after any stage of ore characterization. However, it is ideal to have completed as many steps in the ore characterization as possible in order to have the most information of the initial feed material. The main economic minerals in the samples are isocubanite (CuFe2S3), chalcopyrite (CuFeS2), and sphalerite (ZnS), with minor galena (PbS) and trace amounts of Au and Ag. The minerals show complex intergrowth textures down to the nanometer scale. These samples exemplify the need for advanced microtextural analyses to adequately characterize ore material prior to processing. The complex textures hamper the use of flotation as an efficient technique, due to the inability to sufficiently liberate the different minerals and problems with selectively floating isocubanite. Thus, leaching was the preferred method for extracting metals.

Jan 1, 2018

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By L. Yan, T. Lutz, J. Noll

"Mine disasters, such as fires and explosions, can create a hazardous atmosphere due to the generation of carbon monoxide (CO). After a mine disaster, contaminated mine air can enter the refuge alternative (RA) as miners enter. Most built-in-place (BIP) RAs use an air delivery system to provide an unlimited supply of breathable air through a borehole which also serves to purge contaminants. In order to determine what levels of contaminants enter the RA, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted testing in NIOSH’s Pittsburgh Experimental Mine using groups of 5, 15, and 30 subjects entering the RA. The experiment used sulfur hexafluoride (SF6) as a tracer gas that was released into the air outside of the BIP RA to establish a uniform concentration. After the human subjects entered the BIP RA, the SF6 levels inside the RA were measured to quantify how much of the tracer gas entered the BIP RA. In tests conducted while the borehole air supply was left off as test subjects entered, interior contaminant levels were less than 3% of the exterior concentration. In tests conducted with the borehole air supply activated as test subjects entered, the interior contaminant levels were measured at less than 2% of the exterior concentration. Considering a mine disaster can result in 10,000 ppm of CO in the mine atmosphere, these percentages indicate that unhealthy CO concentrations that may lead to headaches, dizziness, and loss of judgement can occur in a BIP RA. This information will help mines make decisions concerning air locks, air delivery systems and a determination if purging mechanisms are necessary. INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and enforcement of mine safety standards (MSHA, 2006). Section 13 of the MINER Act specifically directs the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of RAs for underground coal mines. This mandate culminated in the 2009 adoption of changes to the 30 CFR mining health and safety regulations, requiring underground coal mines to provide RAs capable of maintaining a life-sustaining environment for persons trapped underground. Such RAs can be either pre-fabricated or BIP shelters. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe, breathable atmosphere within RAs."

Jan 1, 2018

By D. Marcotte, R. V. Dutaut

"In mineral resource evaluations, geostatistical methods known as global change of support allow prediction of the theoretical histogram and gradetonnage curves prior to interpolations or simulations of grades. Two methods commonly used by professionals to guide the choice of interpolation parameters and assess results are the discrete Gaussian model (DGM) and the indirect lognormal correction (IndLog). These models rely upon an estimate of the dispersion variance of the blocks, which is derived by numerical integration of the variogram model over a discretized block. Due to difficulties in obtaining well-formed traditional experimental variograms (especially in the presence of outliers and limited clustered data), many professionals prefer to use ‘normalized’ variograms such as correlogram (non-ergodic variogram), pairwise-relative, or variogram of the normal score transform. A series of simulations with different grade distributions and variogram models are used to assess the performances and robustness of the various variogram estimators with respect to the DGM and IndLog global change of support. Our results show that the traditional variogram, the correlogram, and normal score variogram have better performances, compared to pairwise, for both DGM and IndLog. Moreover, DGM provided better results than IndLog for the grade distributions that are not strictly lognormal. These findings provide valuable guides for geostatistics practitioners. IntroductionWhen reporting resource estimates,practitioners are required to follow generalstandards described in the NI43-101 (CIMguidelines), JORC, or SAMREC codes. One cangenerally recognize three main parts directlyrelated to the block model:•,Pre-processing: exploratory data analysis (EDA), domaining, capping, compositing, declustering, variography•,Processing: block size, neighbourhood, interpolation types (linear or nonlinear)•,Post-processing: classification, reporting.Pre-processing aims to simplify and strengthen the processing step. Ideally, domaining, capping. and compositing is aimed at defining a single homogenous population. During the processing phase, a common practice is to use a block size corresponding to the planned selective mining unit (SMU). In most precious metal deposits (gold, notably), the SMU size is frequently smaller than the recommended half data spacing (Journel and Huijbregts 1978), resulting in high estimation variance and either a high degree of smoothing if the regression slope is managed or a high degree of conditional bias if it is not. Most actual resource estimates are made using block sizes between one-quarter to one-sixth of the average data spacing, sometimes even smaller. In addition to the block size, the interpolation choices for the neighbourhood selection and interpolator (e.g. inverse distance (ID) or ordinary kriging) are often based on the Qualified Person’s (the QP) experience and some basic validation plots that often do not consider the conditional bias (e.g. trends or SWATHs plots, which are designed to compare two sets of population using a one-dimensional graph)."

Jan 1, 2018

By Y. Y. Li, Q. Chen, Y. X. Cai, Q. Zhang, S. Mao

"Due to the influence of combustion conditions, the fly ash produced by some power plants has the problem of high-carbon content. The unburned carbon in fly ash can be removed by flotation, and the decarbon tailings should reach the national standard level I fly ash. The fineness of the requirement is one of the important indicators and is also an important factor affecting the tail ash activity. In this paper,adopting two methods investigate the effect of particle size on the flotation index: one is direct flotation of fly ash, and the other way is wet grinding + flotation of fly ash, comparing the two methods and selecting the appropriate process,which provides a way for the effective utilization of fly ash. INTRODUCTION Fly ash is a solid waste discharged from coal-fired power plants. The annual amount of emissions of fly ash are very large in China. The amount of fly ash were discharged from coal-fired power plants are increasing gradually, and the amount of fly ash stored has exceeded 2.5 billion tons, but the comprehensive utilization of fly ash is not high, which brings about a huge environmental problems( Lu et al.,2011). Carbon is a harmful component of fly ash in cement and concrete application (Zhang et al.,2008). Fly ash decarburization is an essential link to improve the utilization efficiency of fly ash and the reduce pollution ( Yang et al.,2012). Carbon is selected from fly ash to make full use of fly ash resources and improve utilization of fly ash (Li et al.,2008). In this paper, the flotation decarburization of high-carbon fly ash is studied, through comparing the grinding and not-grinding processes, optimizing the separation process of fly ash, which provides a way for the effective utilization of fly ash."

Jan 1, 2018

By G. Weingrill, H. Flachberger, J. Neubacher

The so called Bublon®-process is an innovative process for the controlled expansion of volcanic glasses such as Perlite and for thermal treatment of other minerals. In this manner, functional light fillers with astonishingly altered physical properties can be manufactured. In contrast to conventional Perlite expanding processes no fossil fuels are burned in order to achieve the expansion. Instead, the feed material is heated electrically mainly by radiation based on heat transfer from heating elements. The main advantage is the better controllability of the production process. Therefore, the heating elements are segmented along the flow of the particles, hence in direction of the ongoing expansion. Overheating of the particles, which ultimately leads to the destruction of the particle surfaces and consequently decreasing the quality of the expansion product, can be reduced significantly. Due to flow characteristics and settling behaviors of fines the lower particle size limit of the feed in this process is restricted to not less than 100 µm. Otherwise process instabilities are to be expected. Manufacturing industry demands light and fine hollow microspheres. Therefore, a proven cooperation between Montanuniversität Leoben and Bublon GmbH was formed to develop a new process called ‘Bublite’. This issue was addressed by changing the conveying principle into a pneumatically conveying system transporting particles from the bottom to the top of the kiln by the means of a drag flow. This approach makes it possible to handle the difficult flow patterns in the kiln and to control the retention time of the particles in the heat transfer zone. As a result, it is now possible to expand very fine Perlite particles into a high quality functional lightweight filler with a glazed-closed surface. The dependence of the polymer industry on importing this kind of fillers from overseas can be reduced by producing it close to sites of demand. Also the Perlite mining and processing companies benefit from this technology because the mine lifespan and the output of the processing plant can be increased.

Jan 1, 2018

By T. N. Matveeva, L. B. Lantsova, N. K. Gromova

"Multimetal gold-antimony ores are complexed processing products, since they are characterized by veindisseminatedsulfide mineralization with fine-dispersed submicroscopic gold, low content and uneven distribution ofAu, which is concentrated together with iron sulfides (pyrite, arsenopyrite, pyrrhotite). Such ores are classified asrefractory ones and characterized by low gold recovery rates during cyanation. A particular feature of gold-antimonydeposits is the presence of antimony in industrial concentrations therein, along with gold that significantly increasesthe value of these deposits. The main antimony mineral is antimony sulfide - antimonite (stibnite). Gold-antimonyores undergo flotation concentration with producing collective gold-containing concentrates or gold sulfide andantimony concentrates. The purpose of the work is an experimental study of the flotation separation mechanism ofsulfide minerals of copper, antimony and arsenic using tannin-containing modifiers during processing of multimetalgold-bearing ores. During the research it was established that for the selective separation of antimony and arsenicsulfide minerals into concentrates of different kinds, it is possible to use vegetable reagents capable to be selectivelyadsorbed on the arsenopyrite surface. Using the laser KEYENCE VK-9700 and electronic LEO-1420 VP INCA-350microscopy methods, it has been established that the film of a vegetable modifier was not washed off with water andfixed firmly enough on the surface of the polished sections of arsenopyrite. In the X-ray spectrum there are C and Obands related to the reagent structure. The vegetative reagent is fixed both on the pre-adsorbed phase of the collectorand on the areas free from the collector. On the polished sections of antimonite before and after a contact with thetannin solution, only partial adsorbed tannin phases are detected, which disappear as a result of subsequent washingwith water.The reported study was funded by RFBR according to the research project ? 16-05-00646 ?."

Jan 1, 2018

By Ron J. Elliott, Dylan Wedgewood

A series of five signature holes were blasted at the Highvale Mine and the resultant seismic data was analyzed to make recommendations on how best to address neighbour complaints regarding blast vibrations. From an analysis of peak vibration levels measured at the closest neighbour for blasting during 2016, it was determined that the blast vibration intensity varied between 1.4 to 4.3 mm/sec (0.06-0.17 ins./sec.), well below the level of concern for the onset of minor damage to residential structures, however, the frequency of the blast vibrations was between 2.2 and 9.7 Hz, which is within the range of the natural resonant frequency for a single story home. This was determined to be the cause of the neighbour complaints, as the home would be responding to the blast vibrations.

Jan 1, 2018

By Thi Hien Tran, Ngoc Anh Tran, Thi Thu Hien-Dinh, Duy Anh Dao

"Natural graphite exists mainly in three types of amorphous graphite, flakes graphite and lump graphite. Graphite from Bao Ha mine, Lao Cai province is with 11.8 carbon-graphite %, forms in flakes and dense crystals. The paper presents the comparison among enrichment of Bao Ha’s graphite by two types of froth flotation with 90 g/t kerosene oil as collector, 50 g/t montanol 800 as frother, in natural pH, and at 20 wt.% of solid. The differences among three flow charts indicated that using middling flotation and re-middling flotation for the cleaning tails and the scavenger concentrates, the final concentrate was improved and containing up to 94 carbon-graphite % of flakes graphite, up to 82 carbon-graphite % of fine graphite with 93.48 % total recovery, moreover, carbon-graphite in the final tail is 0.86 % with 6.52 % recovery. However, a refining mill and a classification stage were applied before doing the middling flotation stages.1. INTRODUCTIONGraphite (black lead or plumbago) is used in many industrial applications due to its high electrical and thermal conductivity, lubricity, and chemical inertness. High quality graphite can be used in metallurgy, molding, brake linings, batteries, and fuel cells. Graphite, composed exclusively of the element Carbon, is rather common mineral, but fine crystals are rare. Graphite is soft (hardness: 0.5-1 Mohs scale); has a layered, planar structure; occurs in platy or acicular (occasionally) morphology (Minerals.net; Pierson, 1993).USGS (2017) reported, global consumption of natural graphite continuing increase in the period of 2012-2016. In 2016, China used up 35% while produced 66% of the world’s graphite. Graphite mining are being developed in Madagascar, Mozambique, Namibia and Tanzania, but production reduced in Canada from 2015. Based on the statistic of Statista.com shows from 2011 to 2014 and a forecast to 2020, the global graphite demand is mostly in refractories, batteries, others, lubricant/crucible, foundry and pencil, and that is increase every year.Graphite Vietnam lies on the fault of the Red river from Yen Bai to Lao Cai, the reserves is estimated around 29.3 million ton and mostly in Lao Cai province where has Nam Thi graphite mine and Bao Ha graphite mine (MOIT, 2008). Vietnamese graphite products could reached to ~92% graphite carbon (Cg) (Tran Thi Hien et al., 2008). Studied samples was collected in Bao Ha graphite mine, is located in Lao Cai province. Graphite Bao Ha exists in two types as graphite flakes and amorphous (Hoang Thi Minh Thao et al., 2017)."

Jan 1, 2018