Search Documents

By Xinzhi (Thomas) Du

"In order to monitor the overburden strata deformation over a longwall mining area in the Pittsburgh Coal Seam, three boreholes were drilled across the longwall panel. Each borehole employed multiple-point borehole extensometers (MBE) to monitor overburden strata movement during and after the longwall face passed under the study area. The longwall face in the study area was 1,428 ft wide and 4,000 ft long. The average mining height was about 7 ft. The overburden depth ranged from 550 ft to 650 ft with an average of 600 ft. The final extensometer readings indicated that overburden strata initially showed sign of movement when the longwall face was 700 ft inby the MBE. The rate of strata movement accelerated when the face was 300 ft inby MBE. When the face was directly under MBE, a sudden anchor displacement occurred, indicating rapid strata movement once under-mined gob. The readings showed insignificant strata movement after the longwall face was 400–700 ft outby MBE.INTRODUCTIONThe longwall mining method is an efficient mining method of underground mining. Surface and subsurface strata are inevitably disturbed above the longwall mined out gob. Figure 1 shows the four zones of disturbance in the overburden strata in response to longwall mining.A longwall shear cuts the coal seam and allows the immediate roof strata to cave into irregular blocky material to fill the void. This is called the caved zone. The caved zone extends from the mining horizon to six or eight times the mining height, depending on the bulk factor of each caving strata layer. The fractured zone is located above the caved zone, in which the strata breaks into regular blocks by vertical or sub-vertical fractures caused by bending forces due to the weight of the underlying strata. The surface soil and rock crack zone extends to approximately 50 ft below the surface. The surface cracking is caused by downward movement of the surface. Between the fractured zone and surface crack zone is the continuous deformation zone. The strata in this zone deforms gently without causing any major cracks that extend long enough to cut through the thickness of the strata, as in the fractured zone (Peng, 2006).The objective of this project is to provide fundamental rock mechanics research about overburden strata movement response to longwall-related activity. The findings aid in better understanding pillar stability, gas well subsidence management, hydraulic impacts, and numerical modeling."

Jan 1, 2018

By M. Fig, B. Treffner, J. Brune, C. Strebinger, G. Bogin, D. Pardonner

"Methane gas explosions in a longwall coal mine can originate from in or around the gob and can seriously harm nearby workers and equipment. In order to fully understand the explosion flame and pressure wave propagation in the mine, it is important to investigate methane flame propagation in confined spaces as well as flame interaction with rock rubble and other mine structures. The latter can lead to enhanced turbulence causing high-speed deflagrations and/or detonations. Researchers ignited methane-air mixtures in horizontal, cylindrical reactors that contained inserts to simulate various gob characteristics. Rock surface topology and ignition location were investigated. Results show rock surface roughness increased fluid motion, thereby increasing methane flame front propagation velocity, overall pressure rise of the explosion, and time of pressure decay. Moving the point of ignition away from the open end of the reactor resulted in an increase in peak overpressure and an overall pressure rise of the explosion. Experiments were used to validate a computational fluid dynamics (CFD) combustion model that will be incorporated into a mine-scale explosion model to simulate and predict explosion hazards of large scale methane gas deflagrations in longwall coal mines. INTRODUCTION Coal mining is an integral part to our global society with coal-fired power plants providing about 40% of our global electricity [1]. A common method of extracting coal underground is by longwall mining. Researchers and investigative reports have found that explosive gas zones of methane-air mixtures can form along the longwall face and within the longwall gob, presenting an explosion risk to nearby workers and equipment [2]. In an explosion, the resulting flame and pressure wave presents a fatal traumatic injury hazard and can cause serious damage to equipment. In order to evaluate and mitigate the explosion risks in longwall coal mining, researchers at the Colorado School of Mines are developing a coupled CFD and combustion model of a longwall coal mine. The purpose of the model will be to better predict the explosion hazards under various mine conditions in order to build stronger prevention and mitigation strategies for miners."

Jan 1, 2018

By Caibin Wu, Ali Lei, Ningning Liao, Jingsheng Ye

"The particle size distribution characteristics of ground product can influence the quality of the classification overflow and the next beneficiation indexes in an ore concentrator. Usually, the size distribution of ground product is considered to be determined by that of new ball mill feed. However, based on large amounts of data from industrial grinding circuit surveys, this paper has clearly shown that the size distribution of ground product should be determined by the size characteristics from classification underflow unless the circulating load was small, because the new feed is an important component and occupy a dominant position of mixed ore from belt feed and classification underflow. On the other hand, the correlation coefficient of the size distribution between ground product and classification underflow can be more than 0.99 when the relevance principle and its method are used. Meanwhile, their P80 value also keeps a synchronous correlation. The greater the capacity of classification underflow is, the higher the correlation of size distribution between the ground product and the mixed feed is. Furthermore, the correlation coefficient of the size distribution between ground product and classification overflow which is from primary or secondary can be 0.96. It is another discovery that the correlation coefficient is related to the type of classifier. The coefficient of size distribution of overflow and underflow from hydrocyclone is superior to that of spiral classifier, which can explain the reason why the hydrocyclone is widely used to replace the spiral classifier in concentrator.INTRODUCTION It is well knows that ball mill circuits closed with cyclones or spiral classifier such as a primary grinding circuit, a secondary grinding circuit and SAB mill have become an industry standard. Which grinding process employed will be determined by the P80 value of ground products. When the primary closed circuit ball mill or SAB that it is different throughout between the two processes was employed, a grinding fineness with -200mesh under 68% will be available. However, the secondary grinding circuit with the fineness of -200mesh above 80% can be conducted. Of course, the grinding fineness is determined by the grain size characteristics of the mineral."

Jan 1, 2018

By Stephen C. Tadolini, Anand Bhagwat

"Intrinsic supports installed in mines with limited seam or mining heights have always proven to be difficult when the required support length is longer. To date, three solutions have been used to ensure that the correct length bolt is installed to achieve the required anchorage or to maintain immediate roof material: combination bolts, milled-notch bolts, and hot-notch bolts. The combination bolts use threaded sections and couples, which can be screwed together to form the required length. The primary bolt of choice, to minimize costs and achieve the desired support, has been milled- or hot-notch rebar bolts. These notches can be placed at strategic (required) locations along the bolt axis, so the bolt can be successfully bent and straightened during the installation process. However, these notches can reduce the strength of the bolting system; special reductions are detailed in ASTM F432-13 (2013). Technical advances in steel rolling and forged heading processes have led to the development of a deformed rebar bolt termed, the BORE bolt, which stands for Bendable Oval REbar. The BORE bolt can be bent at any location and straightened during the bolt installation cycle. This support exceeds the minimum designed capacities described in ASTM F432-13 and meets the yield and tensile strength requirements of a full diameter no. 6 rebar bolt. The profile and shape also reduces the resin annulus during the installation process to enhance mixing and shreds the cartridge film to help eliminate glove fingering.INTRODUCTIONThe height or depth of competent strata material, in the immediate mine roof, can be greater than the developed mine openings heights. This is especially true in coal mine openings where 50% of the minable seams in the US are less than 50 inches (132 cm). When this scenario occurs, it can be difficult to insert steel bolts in a solid single length. Figure 1 illustrates what difficulties can be experienced when a roof bolter operator is working and supporting a thin seam coal mine. There are three viable options currently available. Lengths of the bolt can be threaded and a steel coupler can be used between the sections to reach the required depth of anchorage. These systems, called “coupled bolts,” usually require a larger diameter hole to facilitate the larger coupler diameter and can be anchored with an expansion shell, resin, or a combination of both. To ensure that the coupler will develop the tensile capacity of the bolting system, required by ASTM 432-13 Standard Specifications for Roof and Rock Bolts and Accessories (2013), the threaded bars should be completely rotated and engaged into the coupler. Premature failures can occur when the threads “strip out” if not inserted completely."

Jan 1, 2018

By R. D. Clarke, E. De Souza

"A framework for ventilation planning, with a focus on planning to the end-of-mine life, was developed for the Diavik Diamond Mine, Northwest Territories. This framework was successfully used by Diavik’s mine engineers to select a cost-effective ventilation plan that met the life-of-mine requirements. The framework achieved this result by reconciling the production plan with the ventilation plan. A set of design acceptability criteria was created and a PICK (possible, implement, challenge, kill) chart was used to quickly narrow down the generated ideas for detailed assessment and economic analysis. RÉSUMÉ Un cadre de planification de l’aérage, qui met notamment l’accent sur la planification jusqu’à la fin de vie de la mine, a été développé pour la mine de diamants Diavik. Les ingénieurs miniers de Diavik ont su mettre à profit ce cadre pour sélectionner un plan d’aérage rentable qui répondait aux exigences propres à la durée de vie de la mine. C’est en conciliant le plan de production et le plan d’aérage que cet objectif a pu être atteint. Un ensemble de critères d’acceptabilité de la conception a été créé et un tableau PICK (de l’anglais possible, implement, challenge, kill, une méthode donnant la priorité à certaines actions proposées ou à des idées visant à résoudre des problèmes) a été utilisé pour rapidement limiter les idées générées et les soumettre à une évaluation et une analyse économique détaillées.INTRODUCTION The Diavik Diamond Mine, Northwest Territories, has been an underground-only operation since 2012 and has a remaining mine life of 8 years. In the first year of underground-only operations, the production rate increased from 60 kt of ore per month to more than 160 kt of ore per month. In subsequent years, this rate was continuously increased (Table 1) because the operation went through various improvement initiatives. By the end of 2016, Diavik’s total production was 0.41 Mt (+22.8%) ahead of the 2012 budget for 2016 production."

Jan 1, 2018

By Xinyang Xu, Chen Zhang, Lixia Li, Zhitao Yuan

"Density functional theory was employed to clarify the mechanisms of the activation of a quartz surface and its collection by the flotation method at the molecular level. The calculation results indicated that hydrogen bonds on the quartz surface (1 0 1) existed in pairs while in contact with water. The simulation was carried out to investigate the different effects of Ca2+ and Ca(OH)+ on a quartz surface with hydrogen bonds, and the results suggested that Ca(OH)+ most likely adsorbed onto and activated the quartz surface. Mulliken population analysis of the external oxygen atom of the quartz surface, calcium atom of Ca(OH)+, and the oxygen atom of oleate showed that there were electron transfer and the formation of a chemical bond between Ca1-O1 and Ca1-O3, which were indicative of strong interactions between the three atoms. In addition, the –OH of the Ca(OH)+ contributed to the activation, which suggested that the Ca(OH)+ group acted as a bridge between the surfaces of oleate and quartz.INTRODUCTIONFlotation is an effective separation method in mineral processing that takes advantage of the physicochemical differences between minerals and gangue, and the properties of the mineral surfaces play a key role in this process (Liu et al. 2016, Qin et al. 2017). In the reverse flotation process of iron ore, gangues are captured by cationic or anionic collectors and floated with air-bubbles as tailings, and the pre-depressed iron oxide minerals are left at the bottom as concentrates (Lima et al. 2013, Yianatos et al. 2015, Zhu et al. 2015). Quartz (SiO2) is one of the major gangues of hematite ores and cannot be easily removed. It is a naturally hydrophilic mineral, in which silicon is the cation in its crystal structure and has very limited solubility. Therefore, quartz must be activated, usually by metal ions, for its effective rejection as a float-product by reverse flotation (AIME. et al. 1976)."

Jan 1, 2018

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By Zhu Yangge, Zheng Guibing, Hu Xiaoxing

"Because of the similar crystal structure and surface properties, it is very difficult to realize the efficient separation of magnesite and dolomite by flotation, which is the main reason restricting the utilization of magnesite resources with dolomite symbiotic. To deal with a magnesite resources with high content of calcium impurity in northwest China, a novel decalcification technology by combining flotation with leaching is proposed in this paper. In flotation process, a novel flotation collector with good efficiency and low temperature resistance was developed, and the depression effect of sodium hexametaphosphate was investigated. In leaching process, the leaching rate difference of calcium and magnesium was observed. By industrial test, from the magnesite ore with MgO content of 43.96%,the grade and recovery of obtained concentrate ( calculated by MgO) are 47.28% and 67.68% respectively, at the same time, CaO content decreases from 3.91% to 0.30%, which means that more than 95% of CaO impurity is removed.INTRODUCTIONMagnesite is one of the main raw materials for the production of refractory materials, and it is widely used in metallurgy, chemicals, ceramic, construction and other industries. China is the most important supplier of highquality magnesite resources, accounting for about 60-70% of the world's identified supply of magnesite products is provide by China (Jewell, 2014). In recent years, high-quality magnesite ores can be directly used are going to run out in China, and the utilization of magnesite resources with high impurity content have drawn more attention.The main purpose of purification for magnesite is to remove SiO2 and CaO impurities which affects the strength of the refractory material. Flotation is the commonly used method to remove impurities in magnesite ore. Reverse flotation with cationic collector is usually adopted to remove silicon containing impurities, and a great deal of literature has been reported (Santana A. N. and Peres A. E. C., 2001; Wang and Sun, 2008; Zhu et al, 2014; Wu et al, 2015; Ivan B. et al, 2017). But when the major gangue component is dolomite, it is very difficult to realize the efficient separation due to the similar crystal structure and surface properties between magnesite and dolomite. To solve this problem, researches have studied the surface properties of magnesite and dolomite, such as wettability, electrical property, solubility and solution chemistry (Nermin and Nurgul, 2006; Nermin 2006; Ozbek and Abali, 1999; Lacin et al, 2005; Bayrak et al, 2006; Bakan et al, 2006; Chen G. and Tao D., 2004), but the commonly studied direct flotation using oleic acid as collector is still hard to receive an ideal effect."

Jan 1, 2018

Low-grade ore bodies, increase in rock competency, finely disseminated valuable minerals in the ore bodies, ore variability and water scarcity are among the technical challenges faced by the mining industry. These challenges have increased the business risk, capital investment and operating cost of the mining projects. Since the last 20 years, many large-scale concentrators have been built to cope with the above-mentioned challenges. Comminution, especially the fine grinding is an energy-intensive process. For example, the ball mill has a limitation in the fine grinding regime where the energy consumption increases exponentially when the product size is below 45 µm. The industry has been seeking for solutions that have a minimum risk and total cost of ownership. The stirred milling technology such as the TowerMill is well accepted by the industry as it has demonstrated the attributes required for fine grinding. TowerMill is a matured technology that has been adopted since the 80s for regrinding duty. Recently, this technology was installed in secondary and tertiary grinding duty to prepare a finer feed to rougher flotation. Four units of TowerMills were installed in a magnetite concentrator in Western Australia in tertiary grinding duty. Recently, Nippon Eirich has conducted process performance evaluation on the TowerMill circuit. The outcome of the exercise had indicated that the circuit is consuming 3.4 kWh/t to reduce from 55 µm to 35 µm with a narrow product size distribution. The effect of operating variables such as the specific energy, grinding media size, mill content % solids and mill feed configuration on the grinding efficiency were evaluated at the plant scale. Furthermore, the scale-up methodology was validated. The scope of this paper includes the performances of TowerMill and the validation of scale-up methodology.

Jan 1, 2018

By Tina Schneider

Scientists show that polymetallic nodules and massive sulfides from deep sea mining contain valuable metals. These metals have the potential to overcome future shortages of supply. Hence, companies, government agencies and industrial associations increasingly evaluate deep sea mining as a promising supplement of land mining. Technologies to extract, exploit, transport and smelt polymetallic nodules and massive sulfides industrially are still in conceptual stage and not sufficiently advanced for operation. According to the International Seabed Authority, large scale exploitation would require a successful pilot mining test in order to demonstrate e.g. the technological feasibility but also the conservation of environmental systems services. At the same time, NGO´s and a some scientists point out that large scale extraction of polymetallic nodules and massive sulfides could disturb the habitat of benthic organisms, with unknown long-term effects. Aside from the direct impacts of mining, indirect consequences about leakage are likely. In the oral presentation I will show how companies, government agencies, scientists and association/interest groups perceive and assess economical/technological, social and environmental risks and opportunities of deep sea mining. In order to analyze the perspectives of each stakeholder group on deep sea mining, we conducted 15 interviews with four stakeholder groups and a large scale survey (n = 500, return rate = 13 %) in Germany. We used the concept of sustainability with its economical/technological, ecological and social dimensions for the interpretation of the results. The empirical research shows the following core results:

Jan 1, 2018

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By Chan Min Yoo, Kiseong Hyeong, Inah Seo

INTRODUCTION One of the major concerns for deep seabed mining is its environmental impact, from the disturbance of benthic communities due to the mining activity to the disposal of mine tailings back to the ocean. Yet a significant amount of waste materials would be produced from the on-deck processing on the mining platform, all the materials that produced on the mining platform are to be shipped to the land unless the related regulation and guidelines are developed by IMO and ISA (ISA, 2018). Still, ecotoxicology data for the deep seabed minerals from case studies in deep-sea tailings disposal (DSTD) and submarine tailings disposal (STD) sites are lacking and all other related aspects are also largely unknown. This year, the Republic of Korea has started a research project for the more comprehensive understanding of chemical and physical properties of mine tailings from the on-deck processing and the possible environmental impacts on the marine organisms after its disposal. Based on the scientific data collected from this project, Korea would be able to make recommendations for the methods and technical standards for the deep seabed mining discharges. The subjects of this project are threefold: to understand the physical/chemical properties of the tailings, to model the dispersion of particulates after the disposal, and to assess its impact on the marine ecology. Laboratory Experiments Producing Mine Tailings First, the possible waste materials are produced by mimicking the collecting and dressing processes at sea. The polymetallic nodules (PN) would be mined by using a collector lifting the crushed nodules out of the bottom sediment, and the bottom water, accompanying sediment, and the fine nodule particles which are too small to be recovered would be discharged to the ocean and thus are considered as tailings (Schriever and Thiel, 2013). In the laboratory, PN is crushed into the fragments smaller than 2 cm, abraded in the water using the rock mill, and then sieved to obtain the fine particles to be disposed.

Jan 1, 2018

By C. H. Buck, A. J. Taylor

"In 2015 Vale’s Clarabelle Mill began the process change to enable a higher degree of Cu separation. The flowsheet modification was part of a complete divisional flowsheet change being implemented in Vale’s Sudbury Operations. This paper will centre on some of the Operational Readiness (OR) work, culminating in the commissioning of the circuit in March 2017. The emphasis will be on the implementation of an integrated test plan to prepare for the process flow change through the mill.BackgroundClarabelle Mill (CBM) began making a saleable Cu concentrate in 2006 with the installation of the Cu separation circuit. Typical separation rate was 35-40% of Cu in feed reporting to Cu concentrate based on a target Ni concentrate Cu:Ni target of 0.7-0.8. The remainder of the recovered Cu (55-60%) reported to Ni concentrate and was smelted through the Copper Cliff Smelter.In 2013 a capital project, Surface Facility Upgrade (SFU), was implemented to focus on matching the surface plants capacities with the future mine plan to maximize revenues. This was to be achieved by redistributing the metal flow, specifically Cu, through CBM to increase metal unit content through the Smelter. The amount of redistribution of Cu was determined to be based on maintaining a stable Cu to Ni ratio (Cu:Ni) in the Ni concentrate.The change in Cu:Ni ratio in the Ni concentrate would affect the Sudbury divisional flowsheet, and required process changes across the all of the surface plants. The detail that surrounds the flowsheet changes as a whole will not be discussed, but the outcome of the decisions plays a large role in the operational readiness interactions between the mill, its suppliers and its downstream customers."

Jan 1, 2018

By Eraldo Florêncio, Paulo Couceiro, Manuel Lopez Cano

Specialized marine blasting techniques were required to deepen and widen the access channel and turning basin of the Sudeste Port Terminal in Rio de Janeiro, Brazil. This terminal has been designed to handle the exports of iron ore and other bulk solid cargoes to international markets. The Sudeste Port Terminal is connected to the iron ore quadrangle in Minas Gerais State by a dedicated railway line, giving Brazil’s independent miners a seamless access to global markets. However, the Sudeste Port Project is located in a protected marine environment. Blasting in this area has required a comprehensive blast induced ground vibrations monitoring and analysis program to ensure the safety of the sensitive structures surrounding of the blast areas. Nevertheless, the risk of generating higher ground vibrations on nearby structures due to the combination of short distances, larger excavations layers and complex geology, increased the complexity of the blast due to the limitations imposed by the maximum instantaneous charge and a demanding project schedule. Site-specific test blast programs were planned and executed in order to obtain in-situ vibration data to establish the local attenuation law, and also to better understand the role of dominant frequencies before production blasting started. This paper summarizes the main findings and solutions applied during the marine blasting project in the Sudeste Port Project.

Jan 1, 2018

By Wei Zhang, Jinhong Zhang

"In froth flotation, the adsorption of collector on mineral surface is critical for a successful flotation process. In present work, an atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) on copper sulfides, i.e., chalcopyrite, chalcocite and bornite. The in-situ collected AFM images show that PAX adsorbs on chalcopyrite mainly in the form of oily dixanthogen; while it strongly adsorbs on chalcocite and bornite in the form of insoluble metal xanthate, which binds strongly with the mineral surface. The information obtained from the AFM study shed lights on the collectivity and therefore the selection of specific collector for different copper sulfide minerals in industrial practice.INTRODUCTIONFroth flotation, which treats the highest throughput in mining industry and produces the maximum economic outcome of any surface chemistry process, has been widely applied for the concentration of copper sulfide minerals, i.e., chalcopyrite, chalcocite and bornite. In flotation, collectors are added into the pulp (mixture of water and fine-grained minerals) to selectively adsorb onto the target mineral and render its surface with high hydrophobicity, which is generally beneficial for a strong mineral-bubble attachment and thus a high flotation recovery. Therefore, the adsorption of collector on mineral surface is vital for a successful flotation process and it has been studied by applying various surface analysis techniques, such as IR (Infrared Spectroscopy), CV (Cyclic Voltammetry) and XPS (X-ray Photoelectron Spectroscopy). (Poling, 1963; Allison et al., 1972; Mielczarski et al., 1984; Leppinen et al., 1989; Kartio et al., 1996) These studies have revealed a lot of information, such as the reaction, product and mechanism, of the adsorption of chemicals on mineral surface. It is also of great interest to directly get the image of adsorbed collectors on mineral surface changing with pulp chemistry, such as pH, redox potential, ionic strength and chemical’s dosage."

Jan 1, 2018

By C. Zhou, C. C. Jobes, J. H. DuCarme

"Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM—the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered. INTRODUCTION Continuous mining machines (CMMs) can be up to 10 m (33’) in length and more than 3 m (10’) in width. These machines perform the coal cutting operations in underground room-and-pillar coal mines. Accidents during CMM operation accounts for an average of 250 injuries every year, and 43 miners have been killed by striking or pinning accidents involving CMMs in the United States from 1984 to 2015.Because of these fatalities and injuries, the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 that requires the use of proximity detection systems (PDSs) on all CMMs with the exception of full-face machines (Mine Safety and Health Administration, 2015). Currently, there are five different proximity detection systems that MSHA has approved as permissible for use in U.S. underground coal mines (Mine Safety and Health Administration, 2013). All of these PDSs rely on a miner-wearable component (MWC) to detect the generated magnetic fields that PDSs produce around a CMM (Schiffbauer, 2002). These systems use the magnetic field strength readings in terms of magnetic flux density from the MWC to determine whether a miner is at a safe distance from the CMM. A stable magnetic field is essential for the accuracy of a PDS."

Jan 1, 2018

By M. Board, C. Alexander, M. Ramström, W. Johnson

"Hecla - Lucky Friday is an underground mine that has been in operation for 75 years and produces from depths over 2.3 kilometers (7,500 ft) below the surface. Technical issues at this depth include high rock temperature and seismicity. The use of new innovative mechanization is being examined for ore production. Principal advantages of mechanization are the reduced exposure of personnel, reduced seismic triggers, and increased efficiency. Lucky Friday has partnered with Atlas Copco to design, build, test, and deploy a mechanical miner for primary ore production. We will discuss the background, concept, development and deployment strategy for a mechanical miner. BACKGROUND The Coeur d’Alene mining district in northern Idaho was first discovered over 130 years ago and has been the most prolific silver producer in the US. The Lucky Friday mine of Hecla Mining Company (Figure 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 tonne per day (800 tons per day) from narrow, vertical lead-zinc-silver veins. Cut and fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates, and long travel times for worker transport to mining areas."

Jan 1, 2018

By E. V. Zelinskaya, A. E. Burdonov

"In the raw aluminum production processon electrolyzers with self-baking anodes, during technological operations, flow-regulated treatment and adjustment of the electrolyte chemical composition produced by diesel and floor-rail technology, alumina and fluoride salts are spilled through the ventilation grilles of the electrolysis body aeration channels, leakage in the equipment, machinery and motorized machinery construction elements. As a result of this, a part of the bus station and the level of ± 0 (the basement room with supporting curbstones and columns, on which electrolyzers are installed) are covered with technological raw material. This leads to an increase in the conductor (bus) resistance, contact connections deterioration, cell insulation failure and raw materials loss. For example, at the enterprise ""Rusal-Bratsk"", as a result of the activity, up to 420 tons per month of alumina-containing wastes that are unfit for use in the electrolysis process are formed due to the alumina substantial contamination with salts of iron and silicon, which significantly reduces the technical and economic parameters of the electrolysis process. The main scientific problem is the processing (cleaning) of alumina-containing waste having a complex mineralogical composition of the material, its contrast and structure, from oxides of iron and silicon, using ""dry"" separation methods. In the performing the work process, qualitative indicators of the influence of external factors (air humidity, precipitation, sunlight, temperature difference) on the physicochemical processes components interaction during the raw materials storage are established. On the basis of laboratory tests, it is established that alumina-containing raw materials can be separated and photometric and gravitational separation methods used. A mathematical model of the motion of particles of primary and prepared alumina-containing raw materials in a cascade-gravity classifier was developed. The criteria and factors characterizing the alumina-containing material, as well as influencing and determining the maximum material enrichment, are established."

Jan 1, 2018

By Klaus M. Hahn, Kurt Aasly, Jutta Lennartz, Hermann Wotruba, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Seafloor massive sulphide (SMS) deposits have been identified as important marine metal resources for the future. However, literature on mineral processing of SMS is currently limited, and to date, no research has been published on processing of SMS from either active or inactive hydrothermal vent fields on the Arctic Mid-Ocean Ridge. In this paper, individual SMS rock samples from the Loki’s Castle area were tested. Chalcopyrite, isocubanite and sphalerite represented the main copper and zinc bearing minerals in the SMS samples, whereas the gangue consisted of barite and silica. Based on the X-ray transmission response (XRT), i.e. differences in the atomic number of elements in tested samples, and using portable XRF (PXRF) values of elemental composition, individual particles were classified as a either product (low barium / high to low silicon / high copper and zinc) or waste (high barium / high silicon / low copper and zinc). The classification was based on the elemental composition of the samples with the cut-off grade equal to 0.5% for copper. It was shown that the XRT discrimination analysis correlated well with elemental (PXRF) data classification. The results clearly indicate that X-ray transmission sensor-based sorting can be used a useful technique for preconcentration of SMS rock samples. INTRODUCTION Due to different compositions of investigated samples, sensor-based sorting is a useful technique for preconcentration of different materials. The aim of using sensor-based sorting is to upgrade an ore by reducing the quantity of overall waste material reporting to the next processing stage. This can be achieved by eliminating (reducing) the waste fraction. By applying sensor-based sorting, the energy consumption for particle comminution as well as the required process water and reagents can be decreased. The total volume of the waste rejection leads to a proportional reduction in the total energy costs (Lessard et al., 2014, 2016)."

Jan 1, 2018