Search Documents

By Yuhua Wang, Huilan Yang, Yanqing Jiang, Dongfang Lu

"Generally, the concentration of bauxite flotation tailings is around 10%, a large amount of water in tailings needed to be recycled in the flotation process. Sedimentation and dewatering properties of tailings were investigated under different conditions. Surface high negative charges on mineral particles are the key factor to destroy the settlement of tailings when the pulp pH is around 8.9. Hence, the modification of pulp pH around 7 is necessary to the diminution of the repulsive force between mineral particles and then the acceleration of sedimentation of tailings. Anionic polyacrylamine with molecular weight of 14 million is the best flocculant for the settlement of tailings in all tested polyacrylamines. P-toluene sulfonic acid shows better properties than hydrochloric acid for pulp pH adjustment when anionic polyacrylamine with molecular weight of 14 million is used as flocculant. Although the flotation of diaspore is depressed in the presence of polyacrylamine using sodium oleate as collector, but the recycling water traded by the combination of ployacrylamine and p-touenesulfonic acid does not show the depression effects on the flotation of bauxite ore. The lower residual content of polyacrylamine in recycling water treated by the combination of ployacrylamine and p-touene sulfonic acid plays an important role. INTRODUCTION Generally, the waste water generated from mineral processing plant is usually treated by sedimentation, oxidization, electrodialysis, ions exchange, active carbon adsorption and flotation technology, and the treated water is also used again in the industrial process. Flotation was adopted widely to improve the quality of bauxite from low grade diasporic bauxite in China. For flotation, the grinding fineness of bauxite is over 90% -0.074 mm, sodium carbonate and sodium hexametaphosphate were used as regulators, so the tailings pulp is very difficult to settle and be dewatered (Y. Wang et al., 2004; Y. H. Wang et al., 2007; Wang Yu-hua et al., 2008; Wang Yuhua et al., 2011). The water recycling of bauxite tailings are becoming the highlight for the industrial application of the flotation process for bauxite ore. Researchers in China shift their attentions onto this topic."

Jan 1, 2018

By R. A. Kleiv, H. Havskjold, N. Church, T. Malvik, M. Tro, E. Larsen

Liberation is one of the major purposes of comminution in mineral processing. In the simplest form, two or more minerals are present in a particle and have to be reduced such that the individual particles contain only one mineral. The complexity of the mineral intergrowth varies from ore to ore. Poor magnetic separation of iron ore may have many causes. In this paper, the emphasis is given to the problem of fine magnetite inclusions in quartz or other gangue minerals. This is highlighted by two Norwegian cases: one on a magnetite ore and the other on a hematite/magnetite ore. The inclusions in question are so small that they are not liberated by reasonable grinding. In both cases, the result has been either poor recovery or lower grade concentrates than desired. The first example concerns production of direct reduction concentrates from magnetite. Magnetic inclusions in gangue particles will be magnetized enough for the particles to pass into the concentrate. The second example is given a more detailed study, where the problem is caused by silicates with small inclusions of magnetite in a combined LIMS and WHIMS separation. This study included microscopy, Davies tube testing, and magnetization measurements. In particular, large gangue particles with magnetite inclusions were shown to have a tendency to bypass the LIMS separators as drag forces in presence of hematite are large. Such particles will then be picked up by the WHIMS as their magnetization is higher than for hematite. This was demonstrated by Davies tube tests, which indicated that such particles were picked up in preference to hematite particles. However, the Davies results did not give a good quantification. Magnetization measurements of gangue particles with magnetite inclusions was shown to be a better tool to quantify the magnitude of the effect of magnetite inclusions in magnetic separation.

Jan 1, 2018

By E. V. Zelinskaya

"Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production. Considerable attention in recent decades has been given to waste recycling. The task is to maximize the use of both newly formed and accumulated solid and liquid wastes. The mining and mining and smelting enterprises industrial waters are a very promising source of secondary hydromineralic raw materials. They have high concentrations of not only calcium, sodium, but also, for example, lithium, rubidium, heavy non-ferrous metals. In general, unfortunately, we have to state that today there is no wide practice of extracting valuable components from waste enrichment, as well as processing of man-made waters to extract metals from them. The quantity of extracted components from underground, and furthermore passing waters, is insignificant. At the same time there is a tendency to increased demand for rare metals: Sr, B, Br, I. This is explained by their wide use in many industries. For example, the consumption of lithium products is steadily increasing. The obtained results showed that in the liquid phase in connection with high salt content and a significant difference in the macro- and microcomponents contents, conditions are initially created for the microcomponents selective isolation possibility. The identified conditions realization is most possible in such technological processes as cryotechnology, sorption and ion flotation. There is an urgent need to expand research in this direction and to recognize as a publicly important task the mining and industrial waste processing full-scale introduction into the practice of operating mining and processing enterprises and iron and steel companies.INTRODUCTION Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production."

Jan 1, 2018

By J. E. Gebhardt, D. McBride, T. N. Croft, M. Cross

"Heap leaching is well-established as a relatively low-cost and low-energy method of extracting metals from low grade ores. However, the design methodology, attention to the engineering details during heap construction and the long time scale in metal recovery makes the process susceptible to significant variation in the success of a heap leach operation. Often the laboratory predicted recovery rates are not achieved on site due to poor understanding of the complex physics of flow and coupled solid-liquid-thermal reactions within the multi-dimensional heterogeneous ore body. Given the large scale of commercial operations, small changes in metal recovery can substantially change the operating profitability. While there are a variety of approaches to heap leach modeling, computational fluid dynamics (CFD) modeling coupled with leach kinetic models offers a methodology to describe and understand the complexities of heap leaching. The CFD model uses leach kinetics specific for the mineralogy of the ore, including gangue chemistry, and provides an energy balance to calculate and predict temperature. Coupled with the CFD model’s inherent capability for modeling complex fluid flow, the physics and the chemistry of the heap can be simulated. This provides a tool for engineering design, as well as forecasting heap production under different scenarios. The calibrated model is used to simulate a three-dimensional test heap under fluctuating meteorological data, such as precipitation events, periodic solution application, and notably temperature. These simulations provide support for a methodology to design and engineer heap leaching of low grade copper sulfide ore. INTRODUCTION Worldwide copper ore reserves are faced with decreasing head grades with copper sulfides, particularly chalcopyrite being the predominant mineralogy (Nesse, 2000). Heap leaching offers an economical way to recover copper from low grade ore. The ore is stacked and a leach solution is applied and allowed to trickle though the porous bed of ore to extract target metals. The heap can be built with run of mine material or crushed ore and is constructed in order to achieve percolation of the leach solution to all regions. Bartlett (1998) provides an authoritative overview of the solution mining process where the leach solution interacts with the solid, the lixiviant dissolves the target minerals from the solid into the solution, and the dissolved species are transported out of the heap for subsequent recovery. Petersen (2016) provides a recent review of heap leach technology and emerging and potential future applications, and Ghorbani et al. (2016) summarizes the current state and challenges of the technology. Early applications of heap leaching offered a low cost technique to achieve high recoveries from oxide ores, typically greater than 70% depending upon the kinetics of reaction. As world copper resources transition to mainly copper sulfide mineralogy, such as chalcopyrite based ores, achieving high recovery from these copper sulfide deposits is proving more difficult due to the complexity of the leach kinetics, which leads to low leaching efficiency."

Jan 1, 2018

By A. M. Muhamedilova, S. M. Narbekova, L. V. Semushkina, D. K. Turysbekov, N. K. Tussupbayev

The research and development of new, more selective collectors in order to improve flotation efficiency represent one of the main priorities in the development of innovative technologies pertaining to flotation separation of various substances and minerals. The use of collectors’ mixtures is considered as the universal instrument for ensuring necessary proportion of chemically and physically sorbed collecting reagents in every individual case. Currently hard-dressed, refractory ores and man-made raw materials, which are characterized by low content of valuable components, fine dissemination of mineral assemblages and similar technological properties of constituent minerals, are widely involved in the recycling processes. The possibility of processing tailings, which are left after flotation beneficiation, has been considered in the case study of tailings of the Zhezkazgan beneficiation plant and the Tishinsk copper ore deposit with utilization of the modified multifunctional flotation reagents. Modified poly-functional collector is the mixture of composite Aerofloat, TC-1000 and butyl xanthate. Reactants ratio is 1:1:3. The advantage of the suggested flotation reagents is that they are composed of two polar groups and have a long hydrocarbon radical. This structure, being in the water during flotation process, plays a dual role: first, as a collector adsorbing on the mineral surface it produces metal complexes with polar groups in the form of bridges; second, apolar radicals flocculate valuable slimed components, thereby intensifying flotation process. It has been shown that flotation of Zhezkazgan tailings with utilization of the lesser modified reagent amount compared to butyl xanthate has enabled to produce crude copper concentrate with 13.0 % copper grade and 80.22 %recovery. Compared to the baseline technology, copper content of crude concentrate has been increased by 5.1 % and the recovery by 31.4 %. It is shown that tailings flotation of the Tishinsky field by applying modified collector allows for increase of the of useful components extraction in a collective concentrate with: copper 9.63 %, lead for 8.41%, zinc 9.2 %, iron 2.73 %, gold 3.57 %.

Jan 1, 2018

By H. Palza, C. Ihle, S. Contreras

"Processing of minerals, particularly treatment of tailings, has been increasingly challenged by the presence of clays in the feed of thickeners. This occurrence is expected to become increasingly important given the nature of ore deposits currently being exploited and those that have been recently discovered. In sedimentation operations (solid-liquid separation), industrial flocculants often fail to coagulate clay-containing fines, generating supernatants with high levels of turbidity, thus implying operational problems. Recently, it has been reported that graphene oxide (GO), a graphite derivative with high oxygen-containing groups, could enhance the flocculation of clay systems, due to the interaction between clays and GO functional groups. In the present work, we investigated the effect of doping industrial flocculants (commercial polyacrylamide) with GO on the floculation of kaolinite suspensions in a solid-liquid separation stage. Separation performance was evaluated by studying flocculation kinetics using a focused beam reflectance measurement (FBRM) instrument, in a set of batch tests. A statistical analysis of the flocculation kinetics and floc population distribution was further carried out. Our results suggest the existence of a synergistic effect between the studied flocculants and GO. This effect is observed as a decrease of clay fine contents in the supernatant, thus improving solid-liquid separation eficiency for high clay containing tailings. INTRODUCTION Copper, given its mechanical, physical and chemical characteristics, is a critical material for the progress of society and so has been from early stages of mankind. Demand for this metal has increased due to the growth of cities and the technological explosion, leading to increase current mining production and reinforce the efforts in exploration for new deposits (Elshkaki et al. 2016). As copper-rich deposits are being depleted, it has been necessary to develop proper technology to mine deposits of lower grades and more complex mineralogies, keeping in mind that the economic window that allows the exploitation of them is reduced by the increase on operating costs (Crowson 2012 and Northey et al. 2014). High clay bearing minerals are found in many of those low-grade copper deposits, and they induce problems in all stages of the mineral processing route (Taner and Onen 2016). Particularly, in the solid-liquid separation stage, the flocculation process fails to remove the clay fraction from suspension and it leads to operational issues such as filter damage, overconsumption of reagents and the need to add an extra clarifying step for the recovered process water. Those problematics pose an interesting challenge."

Jan 1, 2018

By S. P. Nagaeva, O. U. Poperechnikova, A. V. Kuptcova

"In case of free gold presence in ore, there is always problem of a choice between the gravity-flotation and gravity separation flowsheets. Study of morphology of gold being extracted by different methods allows to find the most efficient solution. One of the latest methods of gold concentration for wide range of grain size (-0.8+0 mm) is a flash flotation. The paper presents comparative testing results of flash and centrifugal separation.The goal of the studies was to determine process and flotation parameters of flash flotation. In case valued minerals are soft if compared to host rock, such minerals tend to concentrate into circulating load of grinding circuit. Thus, valued minerals can be overground, and in turn, will result in low extraction in flotation circuit. Integration of flash flotation operation into process flowsheet has been evaluated. Flash flotation operation can be successfully used not only for gold but also copper, lead, nickel and silver minerals.With low-sulphide ores being a case study under laboratory conditions, various flotation (impeller rotational speed, air flowrate) and process (pulp density, collector consumption, frother consumption, time of flotation) parameters were studied in view of its impact on gold flash flotation. Experiments were carried out under laboratory conditions using special pneumatic mechanical flotation machines.INTRODUCTIONGravity separation is used for extraction of coarse gold before cyanidation and before flotation of polymetallic ores to increase gold total recovery into gravity copper and lead concentrates.Benefit of the flash flotation is efficient recovery of coarse gold carrier particles (sulphides) thus preventing its regrinding and, as a result, low recovery. Furthermore, combination of flash and conventional flotation results in final tailings that do not require further cyanidation.Combined gravity-flotation flowsheets are designed for concentration of ores containing gold within thewide range of grain sizes (see Table 1)."

Jan 1, 2018

By R. Shiva Kumar, G. E. Sreedhar, Rajan Kumar, K. Suresh, A. K. Aketi Veera, M. Narasimha, P. S. Jodan

"In most of the coal washeries, Dense Medium Cyclone’s (DMC) are deployed to treat coarse coal fraction in the range of 50-0.5 mm. DMC’s are very popular due to its ability of high tonnage, ease of operation and effective separation at high near-gravity material (NGM) in feed coal. The ease or difficulty of washing is merely depending on the NGM fraction present in run of mine coal. However, the quantitative effect of NGM on DMC performance was not explored in the literature. Hence, in this investigation, the influence of NGM on DMC performance is focused. With the help of synthetically prepared coal mixture, the effect of NGM mass fraction on separation efficiency is studied in three different approaches. Firstly, by increasing the NGM coal fraction systematically from low to as high as possible; second by varying the distribution of NGM coal; and third by varying distribution of particles lying just above and below the near-gravity zone. Washability studies are also carried out to establish the theoretical yield for the prepared synthetic mixtures. Pilot-plant experiments are carried out in a 4-inch DMC with 1.4 operating separation density treating coal in the size range of 4 - 0.5 mm. From results, the partition curves are constructed by both density and size wise distributions. It is observed that at higher NGM coal fraction i.e above 60%, the performance of DMC is very poor with significant coal particles misplacement. In second approach with increased distribution at higher density fractions, the separation efficiency reduces. In third series the distribution of fraction in near-gravity zone doesn’t much effect the separation except the shift in separation density. It is observed that smaller size (-0.5 mm) coal particle having high NGM content seems have a profound effect on DMC performance leading to significant fines misplacement to wrong products."

Jan 1, 2018

By M. Rafieazad, P. Fathi, X. Duan, M. Mohammadi, A. M. Nasiri

"Direct metal laser sintering (DMLS) is a metal additive manufacturing technology that creates highly complex components by fusing metal powder into a solid part. In this study, the impact of surface roughness on corrosion resistivity of AlSi10Mg_200C alloy manufactured through DMLS was investigated. The as-printed DMLS-AlSi10Mg _200C alloy was subjected to various surface finishing processes including grinding and sandblasting. The corrosion performance of the surfaces was then evaluated using potentiodynamic polarization testing and electrochemical impedance spectroscopy (EIS) in a 3.5 wt.% NaCl solution to mimic seawater environment. Surface characterization and corrosion morphology of the samples were assessed by Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) spectroscopy. The results of this study show that the surface finishing process and the resultant surface roughness has a significant impact on the corrosion resistivity of the DMLS-AlSi10Mg_200C alloy in the seawater environment.INTRODUCTION Direct Metal Laser Sintering (DMLS), also known as Selective Laser Melting (SLM) (Sames, List, Pannala, Dehoff, & Babu, 2016), Laser Beam Melting (LBM), or Laser Metal Fusion (LMF) (Herzog, Seyda, Wycisk, & Emmelmann, 2016), is an additive manufacturing process that utilizes a precise, high-power laser to micro-join powdered metals and alloys layer by layer to form almost fully dense and functional components in three dimensions from the 3D computer-aided design (CAD) data. Complex geometries not possible with conventional manufacturing processes can be readily manufactured with high accuracy using the DMLS process with no need to time-consuming tooling."

Jan 1, 2018

By Jia Ma, Zhi-Chao Liu, Kang Liu, Chun-Feng Li, Bao-Bin Tang

"The geological environment of the certain uranium-molybdenum deposit is very complicated. While the study of process mineralogy is relatively few, which restricting the processing and leaching effect of ores. According to reaserch on process mineralogy of this mine, the basis of ore processing can be provided. The main contents of research are the uranium occurrence state and the influence of H2O2 in acid leaching. By various methods and experiments, the process of uranium mineralogical characteristics in this deposit are systematically studied. The results show that the uranium is mainly in the form of independent uranium minerals. The structures of these uranium minerals are venous and disseminated in mineral fissures, or microgranular inclusions in quartz and feldspar. It is not appropriate to concentrate the uranium minerals by flotation beneficiation because that the loss rate of target metals via water leaching process is very high. The ores are suitable for being acid leaching directly with 6% – 8% of H2O2, and the maximum leaching rate of uranium can be 96.88%. INTRODUCTION The uranium ores with associated elements have a large proportion in uranium resources (Lei, et al., 2014, Xing, et al., 2006; Ritchy and Wong, 1985). The uranium and molybdenum are easy to be paragenesis in nature enviroment because of their similar chemical properties. Therefor the uranium-molybdenum associated deposits are widely existing, such as the sedimentary sandstone uranium deposit in American with vanadium and molybdenum, the sedimentary sandstone uranium deposits in French with vanadium (Chen, et al., 2014; Lounis, 1997). A certain epithermal porphyry uranium-molybdenum deposit in China is mainly controlled by the subrhyolite- porphyry and the fault zone (Lv, 2012; Rui, 2010; Liu, et al., 2010). The ore properties of this deposit are complex, which include the high alteration degree, and the fine grain size of the target minerals (Ma, et al., 2013). The ore properties and occurrence state are quite different during each mining stage. As a consequence, the consumption of reagent increased and the leaching rate declined as long as the continuously mining. The author explored the best leaching rate of target elements According to the basic research on process mineralogy of present ores, experimental study of water leaching and oxidizing acid leaching on different particle sizes."

Jan 1, 2018

By A. L. Ling, A. K. Janzen

"Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software and water quality calculations provided by PHREEQC, and is well-suited to modeling parameters of interest in the mining industry, especially metals and sulfate. Physical processes such as membrane separation and greensand filtration are modeled by defining mass rejections for each parameter and flow routing based on vendor projections and bench- or pilot-scale equipment testing. GoldPHREEQC models chemical precipitation processes such as HDS metals removal and gypsum precipitation by (1) performing surface-aging and solubility calculations in PHREEQC and (2) using the GoldSim framework to direct supernatant and precipitate to subsequent process steps. Users can apply this modeling framework to predict effluent water quality, chemical requirements, sludge production, and required equipment capacity to support design, troubleshooting, and cost estimating. INTRODUCTION Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software (1) and water quality calculations provided by PHREEQC (2), and is well-suited to modeling treatment of parameters of interest in the mining industry, especially metals and sulfate. GoldPHREEQC can also be applied to other water treatment scenarios using inorganic reactions and processes. The GoldPHREEQC model framework moves water and mass between specified model nodes and calculates specified reaction and water quality outcomes. It can be organized to provide flow, load, and concentration information for each location, including effluent and byproduct streams, and outputs can be adapted to include power and chemical costs."

Jan 1, 2018

By Yi Ran Zhang, Nawoong Yoon, Brent Hilscher, Maria Holuszko

"Ore sorting technology has been rapidly advancing in recent years. Improving expected mill feed grade has a significant benefit to project returns, and can no longer be ignored. When there is an increase in the mill feed grade while maintaining the same throughput, the mine will be able to process much more metal and improve the floatation recovery. There are many more factors that contribute toward the economics of the project by implementing sensor-based sorting technologies covered in this paper. This paper reviews the economic impact on an underground copper-silver deposit with references to the concept of ""profit recovery,"" which is the measurement of recovery based on rock profitability rather than just metal content. The economic impact of sensor-based sorting is discussed in detail throughout the paper. The preliminary economic evaluation of the project compares the mine's base case design versus a design incorporating sensor-based sorting. The paper's primary focus is on economic impacts rather than the explanation of the sensor based sorting results. The sorting data is presented on a scoping level and using a sensor-based sorting study where the best possible results are used for obtaining the grade recovery curves. Also, the breakdown and analysis of the project economics are based on the operating cost available from the particular operation. Any assumptions taken into consideration are also outlined and discussed. INTRODUCTION The mining industry has been adopting Sensor-based ore sorting technology fairly rapidly in the recent years. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes should not be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. The answer to this is the creation of a new term and concept - Profit Recovery™."

Jan 1, 2018

By M. D. Vilarinho, W. Xuan, F. Vasconcelos Guimarães

"This article summarises the efforts to reduce the energy consumption in grinding in a magnetite ore beneficiation plant. ArcelorMittal Kryvyi Rih ore beneficiation plant produces magnetite concentrate at 65% Fe and 8% SiO2, of which the D80 is approximately 44µm after three stages of grinding with ball mills and magnetic separation. Characterisation and laboratory scale bench tests performed on samples from the beneficiation plant indicate that the industrial flowsheet could be simplified. After the first stage of grinding and magnetic separation, a significant size fraction of the intermediate concentrate is already well liberated. Therefore, it can be directly concentrated in a second stage magnetic separation without further grinding. If a screen of 150µm size can be implemented after the first stage of grinding-magnetic separation, only the oversize of screening, representing 35% of the material, requires secondary and tertiary grinding and magnetic separation. The combined concentrate from the two fractions already meets the industrial specifications. This new route can provide the same final product, with fewer mills; it saves around 30% in energy consumption only in the grinding step without changing the main structures of the processing plant.INTRODUCTION Comminution, including crushing and grinding, is responsible for at least 40% of total energy usage in mining and mineral processing. This paper shows an example to reduce grinding cost, by changing the flow sheet design strategy in ArcelorMittal Kryvyi Rih (AMKR).AMKR is one of the most important mining and steel complexes in Krivoy Rog basin in Ukraine, which has been studied over 100 years because of mining of iron ores. The iron ores are associated to Banded Iron Formation of the Saksagan suite, with an average iron grade of around 36 percent Fe. The total thickness of the Krivoy Rog Supergroup reaches 5-6 km, whereas that of the iron-ore Saksagan Group comprises up to 1400 m. High-grade iron ore extends to more than 2,000 m below present surface"

Jan 1, 2018

By Yuexin Han, Wenbo Li, Yan Shan, Yanjun Li, Shumin Zhang

"With the accelerating pace of resource extraction, the quality of resources is decreasing, and the old tailing dams which have served for several decades have become the focus of attention. The secondary recovery of valuable metals in the tailings is an important aspect of the comprehensive utilization of tailings. The average iron content of iron tailing is 8%-12% in China. The research aimed at exploring the low-cost and efficient technical route to recycle eastern tailings of Anshan iron mining area. The purpose of the research is to scientifically find the rational conditions of magnetizing roasting and to provide an increase in recovery and quality of concentrates. The eastern tailings of Anshan mining area belong to high silicon bearing iron tailings, iron mainly exists in form of hematite-limonite with an iron grade of 10.60%, the main component of gangue is SiO2 with a grade of 76.22%. In order to reduce the influence of the tailings on the environment, fluidized magnetizing roasting and low intensity magnetic separation for the eastern tailings of Anshan mining area were carried out to improve the utilization of the tailings. The results indicated that an iron concentrate with an iron grade of 65.30% and a recovery of 85.85% could be obtained under the conditions of gas flow rate 8 m3/h, H2 concentration 50%, fluidized magnetizing roasting temperature at 600? for 20s. Phase analysis, magnetism analysis and XRD analysis on roasted materials indicated that hematite-limonite could be transformed to magnetite during the fluidized roasting, then the effective separation of iron and gangues could be made easily by the weak magnetic separation. INTRODUCTION It is universally acknowledged that the grade of iron ore in China is low, the output rate of iron ore tailings is high, usually more than 60%. At present, the comprehensive utilization rate of iron ore tailings is low in China. Generally, the iron ore tailings are stockpiled in the tailings dam. The tailing dams not only occupy a lot of land, but also takes a lot of money to construct and maintain. In addition, the noxious substances in the tailings, such as residual flotation agents and heavy metals, have a severe impact on the ecological environment. There is little doubt that tailing dams have a visual impact on the environment due to their regular geometric shape. Iron tailings can be treated as compound mineral, which is an important component of comprehensive utilization of mineral resources, and is an has been widely concerned. Lots of scholars have done a large amount of research work on a large number of iron ore tailings. Since the iron mineral crystal grain size is fine and the iron grade is low, the iron tailings have failed to achieve good selection criteria."

Jan 1, 2018

By B. Dyck, L. Verhelst

"Colloidal silica in Key Lake’s Solvent Extraction (SX) feed solutions has presented an operational problem for the mill throughout its history. The colloidal silica stabilizes aqueous continuous emulsions, resulting in elevated solvent losses and operational downtime. Through the years, many attempts have been made to solve this problem, but no viable solutions were found. By revisiting an idea dating back to the 1979 feasibility study and re-evaluating it under current operating conditions, a practical solution was achieved. This paper discusses Key Lake’s history around colloidal silica removal, starting with coagulation using a polyethylene oxide polymer (PEO), and ending with coagulation using a polyethylene glycol (PEG) polymer. The results of a mill trial using POLYSIL® RM1250 introduced at doses up to 300 ppm into the counter current decantation (CCD) circuit to clarify SX feed solutions are discussed with a focus on the benefits to SX.INTRODUCTION Colloidal silica has historically been a significant operational problem in the Key Lake mill. Silica originates from clays in the ore as well as concrete backfill intermixed with the ore resulting from the mining method used at Key Lake’s ore source, the McArthur River mine. The silica is dissolved as silicic acid into solution in the mill’s sulphuric acid leaching circuit. Once in solution, silicic acid polymerizes (Hearn, Smethurst, & Boskovic, 2016) forming a fine suspension of stable colloidal particles. These silica colloids are unaffected by flocculants and sand filtration reporting to the pregnant leach solution (PLS) as a fine turbidity in solution. Silica concentrations typically ranged from 700 to 1200 mg/L Si in the PLS fed to SX. Throughout Key Lake’s history, silica interactions in the Solvent Extraction (SX) process have made SX a mill bottleneck and a source of significant reagent costs."

Jan 1, 2018

By T. Avilez, D. Salari

"The economics of developing gold deposits containing elevated levels of cyanide soluble base metals is often challenged by high cyanide consumption and increased operating costs. SART is a chemical process that enables cyanide consumed by base metals to be recovered and recycled for gold leaching. The process also provides concurrent recovery of the base metal to generate incremental revenue from the sale of high-grade base metal sulphide concentrates. Although SART was developed and successfully piloted by Lakefield Research and Teck Corporation in the late 90’s and is now a public domain technology, the adoption of SART has been relatively slow due to concerns about implementation costs and the reliability of metallurgical performance. Through extensive experience in selective metal sulphide precipitation applied to mining wastewater since 2007, BQE Water has provided process know-how, design along with operations and maintenance experience to a number of projects involving the integration of SART into various metallurgical flowsheets on an industrial scale. This paper presents the commissioning experience and operating data from a SART plant treating up to 500 m3/hr of leach solution at a heap leach operation in Mexico. INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes to the traditional gold extraction metallurgical flowsheet. A tool available to the industry to help manage the interference of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle."

Jan 1, 2018

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

By A. V. Rasskazova

"The oxidized and mixed ores are processed by heap leaching. Primary ores with high gold content are floated. In recent years mining of primary ores with the low gold content (up to 4 ppm) has increased. Extraction of gold from these ores by floatation is technologically ineffective. Gravity concentration is ineffective for fine gold particles because of their floatability. The research objective was assessment of the viability of processing gold-bearing ore with combined gravitational and hydrometallurgical methods and testing of recovery of metals from a gold-copper oxidized ore chloride-hypochlorite leaching solution. The advantage of chloride-hypochlorite lixiviant is the low cost of reagents which is produced by the electrochemical synthesis of NaCl solution with the addition of HCl. The adsorption of chlorine compounds by a mineral matrix and its ability to oxidize the refractory ore components and allows for the application of chloride-hypochlorite systems for gold recovery for both oxidized and primary ores. The complexity and problem in using a gold–chloride system is the strong adsorption of gold–chloride complexes onto mineral surfaces, such as goethite, quartz, and alumina. In preliminary testing, gold recovery from gravity circuit gold bearing concentrates processed by agitation leaching in chloride-hypochlorite solution, gold recovery has reached up 82% after 4 hours of leaching. Chloride-hypochlorite leaching of copper-gold oxidized ore with preliminary processing by sulfuric acid provided for 94 % gold recovery to solution. Understanding of ecological hazard of cyanides is the motive power of researches in the field of search non-cyanic chemistries to provide for technologically and economically effective solvents of gold. Soluble compounds of chlorine with a suitable oxidizer are one of the alternatives to cyanides. Basic researches of gold extraction by chloride-hypochlorite solution have shown high rates of gold recovery.INTRODUCTION Because of the continued and growing environmental concern for the use of cyanide for gold processing, interest for the use of non-cyanide lixiviants, especially with halides has renewed recently (Tran et al., 2001; Ferron et al., 2003; Bhaghalha, 2007). Leaching solutions based on halides (chloride, bromide and iodide) are viable alternative to cyanide (Kwang et al., 2008). The major disadvantage of the chlorine–chloride system is the high reactivity of chlorine in reaction with sulfide and gangue carbonate minerals. It is believed that only high grade materials may be treated by chlorine–chloride systems economically (Baghalha, 2007). Another important problem of the application of gold–chloride complex is that it tends to be rather unstable and may re-precipitate upon contact with a reductant, such as sulfidic minerals of ore. It is well known that Au(III)–chloride hydrolysis species are strongly adsorbed by goethite, quartz, and alumina (Machfsky et al., 1991). To minimize adsorption of gold–chloro complexes, it works best to minimize the adsorption time."

Jan 1, 2018

By D. J. Borrow, K. van Netten

"A fine coal tailings feed was selectively agglomerated using a concentrated water in oil emulsion binder consisting of 95% aqueous phase and 5% organic phase. The purpose of the study was to investigate a continuous system in plug flow, providing a rapid beneficiation technique with high selectivity and recovery. The development of the novel binder was undertaken in previous work in a batch system consisting of a high-speed blender. In this previous work, it was found that agglomeration could be achieved in 3 s, providing the binder was pre-dispersed. Furthermore, it was found that, depending on the feed, only ~1 wt% of oil was required to achieve agglomeration, some 10 times less than required in traditional oil agglomeration. In a more recent study, the technique was adapted into a continuous process. Due to the rapid speed of the process using the emulsion binder it was found that a simple flow constriction within a 1 inch pipe was sufficient to achieve the selective agglomeration observed in the batch system. In this previous study, a coal feed consisting of a flotation product was agglomerated at a superficial slurry velocity of 1.3 m/s using a partially closed ball valve as the flow constriction. In the current study, a feed consisting of fine coal tailings with an ash content of 50.1% was used to establish the influence of superficial slurry velocity on the agglomeration process. The superficial slurry velocity was varied between 1.3- 4.2 m/s, while maintaining a constant pressure drop of 100 kPa across the flow constriction. The flow constriction consisted of a partially closed ball valve. It was found that increasing the superficial slurry velocity across the flow constriction reduced the amount of organic liquid required to achieve agglomeration. Under the optimum conditions, a combustible recovery of 80.4% was achieved at a product ash content of 9.6%. This work demonstrates a valuable product can be rapidly produced from tailings material using the novel emulsion binder. INTRODUCTION A significant opportunity exists to recover fine coal from material that is currently classified as waste. This waste material, also called tailings, is currently considered not economic to process due to its high ash content, low solids concentration, and the fine size of the particles. Thus, for this opportunity to be realised, a process is required that is highly selective and has the ability to economically recover fine particles at high throughputs. The technique of oil agglomeration has previously been considered as a candidate for the recovery of fine coal, as it is highly selective and has no lower limit on the size of particle that can be recovered (Capes and Jonasson, 1989). However, the cost of the oil required as the binding agent in the process has proven to be a significant barrier to any long-term applications (Swanson, Nicol, and Bensley, 1977). Recently, however, Yoon and co-workers have developed an ultrafine coal separation process that utilizes an oil phase for the recovery of the hydrophobic coal particles and have implemented an oil recycle to greatly reduce the consumption and thus cost of the oil (Yoon et al., 2016)."

Jan 1, 2018

By S. K. Kawatra, J. A. Halt

"INTRODUCTION Iron ore beneficiation needs advances in areas such as process control, automation, burner and furnace designs, silica-free binders, and even alternative iron making routes. While some – like new binders – are only step-changes, all are tools that can help make the ironmaking industry more sustainable. This paper focuses on binders. Binders are added to iron ore fines before they are agglomerated. Binders are used to control the balling process and increase the mechanical quality (e.g. strength) of green-balls and pellets. Agglomeration usually follows thickening and filtration. Good-grade ores, which don't require upgrading, are wet ground to decrease particle size and increase specific surface area. Low-grade ores are often extensively upgraded through wet operations (flotation, dispersion and selective flocculation, magnetic separation, etc.). For both types of ores, thickening and filtration conclude the circuits so that moisture contents are lowered and the ores can be agglomerated. It's been known for a long time that thickening and filtration behaviors are influenced by zeta potential (Sandvik, 1979). Highly-negative zeta potential is good for dispersion while low zeta potential is good for filtration. So, the zeta potentials of iron ore particles are lowered with additions of acid or carbon dioxide, for example, to increase filtration rates and throughputs (Eisele et al., 2005). What happens to particles as their zeta potentials are lowered? Particles aggregate together, effectively forming larger particles. How stable then, are those aggregates during mixing and balling? Are they easily broken up during mixing (if mixers are even used)? Are they broken up during balling? Or, do the aggregates resist breakage so that the availability of ultra-fines, which are so beneficial for agglomeration (Stone, 1968), is decreased? For plants where high doses of bentonite are used as binder, the above questions may be of no concern. The bentonite adds the necessary amount of fines; however, even at those plants, the calcium and magnesium contents in the water affect bentonite's effectiveness (more magnesium and calcium means less effective bentonite). (Engesser, 2003) For plants where new silica-free organic binders are being developed and used, the above questions may need to be considered. The binder is only amongst the iron ore particles for a short period of time – until it burns away or thermally decomposes in the induration furnace – so the liberation, availability and distribution of fine particulates is very critical for the quality of balls and pellets. It was hypothesized that high zeta potential conditions would lead to good pellets, while low zeta potential conditions would lead to relatively bad pellets."

Jan 1, 2018