Search Documents

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018

By Eiichi Sato, Koichi Kitazono, Hiroshi Masuda, Kenta Higane

"The present study investigated the low-temperature creep mechanisms in ultrafine-grained (UFG) aluminum manufactured by accumulative roll bonding. UFG aluminum with grain size 0.39 µm showed steady state creep even at room temperature under low stresses as confirmed by the creep curves in the strain rate–strain plot. The low-temperature behavior was divided into four regions by three distinctive stresses, sI, sII and sIII: sI (=45 MPa) is denoted as the micro-yielding stress with which dislocations start movement, sII (=85 MPa) the dislocation-multiplication stress above which dislocations multiply with creep deformation, and sIII (=171 MPa) the conventional yield stress above which macroscopic plastic strain is generated. During low-temperature creep, below sI, negligible plastic strain is generated. Between sI and sII, creep deformation with stress exponent 2.5 occurred, which is accommodated by dislocation absorption into grain boundary and grain boundary sliding, similarly to the low-temperature creep of HCP metals. Between sII and sIII, creep deformation with stress exponent 7.0 occurred, whose mechanism is similar to the low-temperature creep of coarse-grained aluminum. Above sIII, power-law breakdown occurred.INTRODUCTIONIt is well understood that the creep deformation brings about at high homologous temperatures (T/Tm) of >0.4, where Tmis the melting point, with diffusion processes. Recently, the importance of aluminum is increasing for cryogenic temperature parts such as a metallic liner or a cap in high pressure-hydrogen vessels, and the presence of creep behavior in aluminum at room temperature has become recognized (Matsunaga, 2013;Kassner, 2015).In HCP metals and alloys, especially intitanium, steady-state creep behavior appears at room temperature with apparent activation energy of1/10 of that for self-diffusion(Neeraj, 2000; Matsunaga, 2009).On the other hand, Kassner (2015) claims that aluminum shows creep behavior at room temperature with apparent activation energy of 4/5of that forself-diffusion, but never reaches the steady state. We should note that it is derived from the data obtained from short-term creep tests of few hour, and Matsunaga (2013) already claimed the presence of steady state in room temperature creep in aluminum with activation energy of 1/5of that for self-diffusion.The mechanisms for low temperature creep are considered different between HCP and FCC metals: in HCP metals, grain boundary sliding is observed and is thought to accommodate piled-up dislocations at grain boundaries through absorbing them. The so-called slip-induced grain boundary sliding occurs with low number of activated slip systems(Matsunaga,2009).On the other hand, in FCC metals, many activated slip systems bring about work hardening with dislocation cell structure formation. In the initial stage of creep, it results in primary creep (Kassner, 2015), but Matsunaga (2013) claimed that once the annihilating of a cross-slipped dislocation to another reaches balance, steady state is established. It has been, however, strongly required to show more convincing experimental verification for the presence of steady state in FCC metals at low temperature."

Jan 1, 2018

By K. Bru, D. B. Parvaz

"Electric pulse fragmentation (EPF) is an innovative technology that uses high-voltage pulsed power (HVPP) for the selective comminution of the treated material. Highly energetic electrical pulses are used to fracture rocks at mineral grain boundaries, resulting in extensive micro-cracks and/or complete fragmentation of the processed particles depending on the applied energy. In this study, the EPF technology was applied to a low-grade schist ore containing cassiterite, in order to investigate its influence on the selectivity of the fragmentation. The impact of EPF on subsequent comminution steps was studied by combining either the EPF technology or jaw crushing (used here as conventional crushing) with subsequent impact crushing. The results confirmed the potential of the EPF treatment for a selective fragmentation of the schist ore. This gave the potential advantages of reducing the total energy consumption in the comminution circuit and of improving the recovery of cassiterite during concentration processes. INTRODUCTION The rise in the world consumption of metals combined with the depletion of most of the high-grade ore reserves leads to an increased need to process ores of lower grade, with a more complex mineralogy. To recover the valuable minerals contained in such ores, fine grinding is required, but this process has high energy requirements and leads to the production of a large amounts of fines, which can impede the performance of later concentration processes such as gravimetric separation and flotation. Addressing this issue is a major challenge for the mining industry. Selective comminution methods have the potential to significantly contribute to the profitable exploitation of these low-grade ores by generating cracks specifically at mineral grain boundaries rather than randomly as in a conventional mechanical comminution system. This allows the liberation of valuable components from the feed material without overgrinding, i.e. this prevents unnecessary size reduction of already liberated grains, which leads to a reduction in production of fines and in energy consumption. In addition, rock not fragmented by the process are usually weakened by the dense fracture network generated, which increases grindability of the rock (Wang et al., 2011)."

Jan 1, 2018

By T. Moloane, C. Bergman, Heloise Thiele

"A pilot test campaign was undertaken to evaluate dense medium cyclone separation efficiencies on samples of iron ore fines (-1mm +300µm). Evaluations were done using both gas and water atomised FeSi types across a range of operating conditions in the presence of slimes build-up. A Mineral Liberation Analyser (MLA) was used to measure size, density, shape and liberation data of DMS feed and products. The results of the test work were used to obtain parameters for modelling of the partition size/density response. The findings indicated that accurate density characterisation of the feed ore is essential in understanding product quality and recovery, particularly due to the effect of porosity and micro-inclusions. A significant off-set between cyclone underflow density and separation cut-point (D50) was found indicating that relatively low feed media densities (about 3.4g/cm3) are required to achieve high density cutpoints of over 4.0g/cm3. In agreement with CFD modelling, the separation quality is dominated by viscous effects, hence FeSi type and slimes content will need to be carefully controlled to ensure efficient separation.INTRODUCTION In the South African context, future resources of hematite are expected to be both of lower head grade and will contain a higher content of banded iron formation (BIF) (1). These ores may require finer crushing in order to liberate the high-grade fractions and will thus increase the amount of -1mm material to be processed. In order to efficiently upgrade these materials, it becomes necessary to re-examine both traditional and novel processes to treat material finer than 1mm in size. These include spiral and up-current classifiers, wet high intensity magnetic separation processes, Reflux classification and potentially includes dense medium separation (DMS). This study presents a technical evaluation of fines DMS using a mineralogically-based particle tracking analysis method (PTA) to calculate efficiencies of separation."

Jan 1, 2018

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.

Jan 1, 2018

By S. McPhail, D. Richardson, G. J. Simandl, C. Akam, S. Paradis, M. Yakimoski, A. Teucher, Y. Cui, F. Ferri

Historically, extracting dissolved solids from formation water was economically motivated. Today, main drivers are environmental benefits and regulations, as large volumes of water needed for hydraulic fracturing require treatment before reuse or disposal. The concentration of dissolved solids in flowback water increases with each use and may require treatment prior to disposal. Element recovery from produced water is not profitable unless market conditions are favourable, recoverable elements are abundant, and economical recovery methods are established. Sale of recovered materials could offset recycling and disposal costs. This paper describes markets for Cl, Na, Ca, K, Sr, Mg, Br, Ba, I, B, and Li, and their concentrations in produced water from oil and gas wells in British Columbia. It recommends revising sampling protocol for produced water.

Jan 1, 2018

By Yessengaziyev Azamat, Almagul Ultarakova, Onayev Murat, Barkytova Botakoz

"The research is aimed at solving the processing of waste products of titanium-magnesium production. The aim of the research is to extract synthetic carnallite and industrial products enriched with niobium from waste products of titanium-magnesium production. Analysis of the current state of the titanium and magnesium production in the Republic of Kazakhstan shows the availability of significant amounts of chloride wastes containing valuable components. Magnesium and potassium with an average content of 50-60 % potassium chlorides, 25-30 % magnesium chlorides are lost in the wastes of the titanium and magnesium production. Ust-Kamenogorsk Titanium Magnesium Plant JSC (UKTMP) currently imports carnallite that is a KCl-MgCl2X6H2O binary salt at quite high prices. Chloride wastes of titanium production, sublimates of dust chambers of a titanium chlorinator, sludge of a magnesium electrolytic unit and sludge of a carnallite chlorinator has been chosen as the targets of our research. The analysis of niobium distribution within any solid waste of a titanium slag chlorination process in UKTMP JSC showed that the highest content of niobium is in the sublimates of dust chambers of a titanium chlorinator in the ranges from 0.26 to 1.0 %. Among the niobium extraction technologies considered, the known method of its extraction from the chloride waste is leaching with weak solutions of mineral acids or alkalis in order to convert the chloride salts into the solution to be used for synthetic carnallite extraction. Besides niobium, other impurity components are transferred to the cake and shall be separated from the base metals. The effective method for this is the chlorination process enabling niobium transfer into the sublimates in the form of chlorides and thus separating it from the majority of the impurities. The condensed niobium chlorides are hydrolyzed transferring it into sediments in the form of oxide. New ways of processing waste products of titanium-magnesium production with the receipt of marketable products are relevant in the development of processing of mineral raw materials."

Jan 1, 2018

By Wei Sun, Ruolin Wang, Jianjun Wang, Xiaodong Li, Honghu Tang, Yuehua Hu, Anh V. Nguyen, Haisheng Han, Kefeng Chen, Zhao Wei

It is difficult to separate scheelite especially from fluorite with fatty acid collectors because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface. A simplified flotation process using Pb-BHA complexes was developed to replace the energy-inefficient Petrov’s process of using a fatty acid, increasing the recovery of scheelite and reducing the cost. The relationship between surface chemical properties (crystal chemistry, solubility, and Zeta potential) of minerals and flotation by using a fatty acid or Pb-BHA complexes was studied in detail to provide new insights into the selective separation mechanism. The results indicate that the scheelite surface exposes more O atoms than Ca and that they are negatively charged due to the anisometric dissolution of Ca and WO4, which provides the possibility for separation using selective interfacial reaction. The FTIR and Zeta potential results indicate that both chemical and electrostatic adsorption play an important role in the adsorption of Pb-BHA complexes on the scheelite surface. The XPS results of the atomic composition and binding energies confirmed the presence of the adsorbed Pb-BHA complexes and that O and Ca may be the active adsorption sites. Therefore, scheelite was able to be collected by forming either a Ca-O-Pbcollector or W-O-Pb-collector (BHA). However, fluorite was only able to be collected by a fatty acid collector and colloidal [H2SiO3]n -, and a high temperature was needed improve the selective desorption of the adsorbed fatty acid collector by forming Ca-[H2SiO3]n - on the fluorite surface, resulting in serious problems in industry. However, the Pb-BHA complexes significantly contribute to improving the recovery of scheelite minerals, simplifying the flotation process, and circulation of the residual reagents and water. The new process has been applied in Shizhuyuan Mine, and improved the recovery by almost 10%.

Jan 1, 2018

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2018

By C. V. Deutsch, T. Acorn

Understanding and managing risk is of increasing concern for the mining industry. Although methods exist to model geologic uncertainty based on stochastic modeling techniques and multiple realizations, there are few approaches to manage this geologic uncertainty in pit optimization. Block values can be penalized if the block uncertainty is high, but the goal here is to consider the reserve risk within the pit. This paper presents an approach for pit optimization that considers all realizations simultaneously with a heuristic pit optimizer. The heuristic algorithm maximizes value and also penalizes reserve risk. The inclusion of multiple realizations provides access to the risk or uncertainty in the total pit value. Considering this information permits an active risk management approach that can manage the uncertainty in the reserves within the entire pit.

Jan 1, 2018

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2018

By T. Hollenberg, N. Nolten

The mining industry is one of the major energy consumers in Namibia. Energy costs increase the operating costs of Namibian mines, in particular, the processing plants, and result in an overall increase of production costs. A substantial part of the energy used is directly imported from South Africa. The cost of energy has been increasing rapidly in the past few years and will most likely continue to do so in the future. In 2015, the average wholesale price for energy from national power utility NamPower was US$87/MWh after rising more than 12 percent annually in the two previous years. At peak times, which are early in the morning and late in the evening, imported-energy prices are extremely high and have to be factored into the electricity tariffs. This problem is expected to intensify due to a projected 4 percent annual increase in energy demand. A major target of the Namibian mines, therefore, is to consider possible ways to address energy-saving challenges and to investigate possibilities for the mines to generate electricity internally during peak times. This is in alignment with the mines’ strategic plans and objectives to reduce total energy consumption and costs from both national and foreign electricity suppliers. In this paper, we explore addressing some of the key energy consumption and optimization challenges through process energy reuse and solar energy production to decrease demand for imported energy through a case study carried out in cooperation with Skorpion Zinc Mine and Refinery.

Jan 1, 2018

By Chee S. Theng

As the 2018 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2018 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 344. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2018 Transactions consists of a total of 59 technical papers, encompassing all 25 papers published in 2018 in the Technical Papers Section of Mining Engineering (Vol. 70) and all 26 papers published in 2018 in Minerals & Metallurgical Processing (Vol. 35). Additionally, this volume contains 8 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our Publications staff. As the 2018 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume. The new year brings an exciting change. The publication of Transactions will cease with this volume. Instead, our Minerals & Metallurgical Processing journal has the new name of Mining, Metallurgy & Exploration (MME), and Transactions as well as the Technical Papers Section of Mining Engineering are incorporated into MME. The journal is published in partnership with Springer Nature, and all SME members have free electronic access to the journal.

Jan 1, 2018

By M. E. Buzon, M. E. Gunter

Talc has been the focus of recent civil litigation based on claims that asbestos minerals exist in talc deposits and therefore have caused asbestos-related diseases in those who have regularly used talc products. Such litigation, and ensuing confusion over the petrology and asbestos content of these deposits, challenges the talc mining industry in Montana and elsewhere in the world. The talc deposits in southwest Montana were formed by hydrothermal alteration of dolomitic marbles and are still actively mined. In general, talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic and lacking in amphiboles. This paper includes data from analyses of representative ore samples from this mining region in southwest Montana. The results conclude that the presence of asbestos minerals — both amphiboles and chrysotile — is unlikely and that the ores are nearly monomineralic, as expected. Samples were characterized using a suite of analytical methods, namely, powder X-ray diffraction, X-ray fluorescence spectroscopy and electron microprobe analyses, which allowed us to determine the minerals present and the formation process. Our data and interpretations suggest that previous identification of asbestos minerals in these deposits is not accurate.

Jan 1, 2018

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By B. A. Slaker, T. Miller, M. M. Murphy

An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in.) was measured by the extensometers, photogrammetric reconstructions and laser scanner over a six-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls were significantly lessened.

Jan 1, 2018

By K. C. Kocsis

Underground ventilation systems, which require electricity to operate the fans and fossil fuel for heating in winter, can account for a significant portion of the energy consumption of mines. Recent studies have shown that the ventilation system in deep and highly mechanized metal mines could be responsible for 40 to 60 percent of their overall energy consumption. Presently, underground ventilation systems are designed for peak air volume requirements, which usually occur well into a future stage of the mines’ operating life. As a result, during their early operating stages, the intake air volume of the mines could be well in excess of their true air volume needs. Such ventilation systems could be considered as uneconomic, and to remain competitive the ventilation design needs to improve while the mines are trying to reduce energy consumption and their carbon footprints. This paper introduces a new mine ventilation design method where an underground base-metal mine’s ventilation system is designed by integrating discrete-event mining process simulation (DES) with mine ventilation modeling techniques. Furthermore, based upon the output data generated by means of discrete-event mining process simulations, the air volume requirement for the operating life of the mine is determined for “traditional” versus “activity-based” ventilation requirements. The output data generated through ventilation simulations are then used to quantify the economic and environmental benefits of an activity-based ventilation delivery system.

Jan 1, 2018