Search Documents

By J Rowland, B Belle, M Webber

The Australian underground coal industry has experienced substantial improvements in longwall productivity and, as such, the methods of providing a safe and productive mine environment have needed to evolve and develop. Whilst the primary method of controlling atmospheric conditions is by airflow it has become impracticable or impossible for the majority of Australian longwall mines to contend with all environmental hazards with primary ventilation alone.If the ventilation circuit cannot provide a safe and productive mine environment at an acceptable cost and circuit duty then supplementary controls are required. Examples include pre-gas drainage, post-gas drainage, gas utilisation, refrigeration and innovative dust control systems. Of the 21 longwall operations surveyed in Australia, there were 13 in New South Wales and eight in Queensland.This study represents a timely opportunity for the industry to examine the primary and supplementary ventilation systems implemented in Australian longwall mines and to discuss how to equip the industry to successfully face the future of underground longwall ventilation management in Australia.CITATION:Webber, M, Belle, B and Rowland, J, 2017. Australian longwall ventilation systems, in Proceedings Australian Mine Vent Conference 2017, pp 301–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By M J. Shearer

An investigation into the reliability of the data being collected at the Mount Isa Mines site operated by Glencore in Queensland allowed on-site ventilation personnel to scrutinise pressure and volume measurements collected from the primary surface fans. The investigation effectively identified discrepancies being reported to the on-site remote monitoring system. The difference between the real-time and static measurements on the P63 RAR shaft identified that the in situ differential pressure transducer and piezo annubar system was not operating correctly. This indicated a deficiency of approximately 30 per cent reporting back to the remote monitoring software versus the live readings measured with the Pitot tube bomb and ALNOR AXD610 pressure micro-manometer.Constant monitoring of an operations ventilation network is imperative to ensuring that the underground atmosphere provides a safe and healthy workplace. Further benefits to real-time monitoring allows for the early indication of network failures and promotes increased availability. An innovative approach to out engineer and improve the existing measuring equipment from the 1970s was sought.The use of ultrasonics in the mining industry is not new with ventilation management systems (VMS) equipment available within the marketplace. The introduction and implementation of a reliable product for real-time monitoring was a challenge to overcome due to limited access and suitable measuring points within the mine. The available equipment on the market through mainstream suppliers was not suitable for the unique application required due to the in situ installation of the surface fans. A solution was identified in the oil and gas industry through collaboration and innovative thinking. This paper describes the sustainable approach to implement a reliable air flow monitoring system on-site.CITATION:Shearer, M J, 2017. Case study – an analysis of reliability and efficiency: ultrasonic versus annubar technologies, in Proceedings Australian Mine Vent Conference 2017, pp 51–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By E Westthorp

Final mine sealing of BMA’s Crinum North mine, near Emerald, Queensland was undertaken in December 2015. Due to the benign atmospheric environment at Crinum North, the Queensland Mines Rescue Service (QMRS) Górniczy Agregat Gasniczy (GAG) unit was utilised to reduce oxygen levels throughout the underground atmosphere as part of the final sealing process.The GAG was utilised by way of a vertical borehole from the surface to seam to successfully reduce oxygen levels throughout the underground mine workings. Application of the GAG unit enabled the underground mine to be classified as stable and inert within days of the GAG operation, and subsequently cease gas monitoring at Crinum North. The data and information obtained from this activity provides valuable information to the underground coal mining industry on successful application of the GAG in realistic situations.This paper discusses the strategy used for sealing, the assisted inertisation and the results obtained from the application of the GAG unit. It discusses both the overall results and gives a detailed review of the gas monitoring data obtained via the tube bundle and real-time system, both during and following the use of the GAG unit.Gas monitoring results obtained and the strategy used are critical to share with the industry to obtain a better understanding of how the GAG unit works, and how it can be applied for emergency preparedness, emergency response or planned inertisation.CITATION:Westthorp, E, 2017. A review of the strategy and gas monitoring results obtained during the use of Queensland Mines Rescue Service GAG unit at Crinum North mine, in Proceedings Australian Mine Vent Conference 2017, pp 309–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D Reid, J Black

The adverse health impacts from diesel particulate matter (DPM) exposure are a well-known global concern. The building evidence has triggered underground mining operations to review existing atmospheric conditions and assess the scale of the challenge faced. South32’s Cannington Mine (Cannington) evaluated the ability to provide a healthy atmosphere from a whole mine approach, taking into account existing preventative controls including: maintenance strategies, fuel quality, mining operations, ventilation provisions, monitoring protocols and effective education and training programs.During the evaluation process, Cannington gave due recognition to the advice and guidance provided in the Queensland Guidance Note 21 (QGN21), the Guidelines of New South Wales’ MDG29 and Mining Industry Advisory Committee (MIAC) of Western Australia. Each of these documents advises a dilution rate of >0.06 m3/s/kW is best for reduction of DPM exposure in underground mines.Achieving the prescribed mine ventilation rate typically results in the need to directly invest significant capital into increasing ventilation infrastructure in order to further dilute contaminants. In today’s economic market of volatile metal prices and increasing pressures to meet regulatory requirements, it can become challenging for established metalliferous operations to create a balance between optimisation of current ventilation infrastructure and capital outlay.In order to obtain and correctly justify the requirements for capital investiture Cannington conducted a ventilation operational analysis for the life-of-operation, identifying the existing air volume envelope was adequate for current and future production rates by optimising existing primary ventilation infrastructure through the implementation of a modified ventilation on demand (VoD) and air conservation system.This process achieved sustainable operating and capital cost reductions without compromising delivery of adequate ventilation to work areas. The process also recognised that engaging mine workers’ ownership of their work areas is crucial to maintaining a technically efficient and operationally robust ventilation system.This paper will concentrate on Cannington’s existing preventative controls, their implementation and their management for the prevention of increased DPM exposure; reducing the risk of both short and long-term health impacts to ‘as low as reasonably achievable’ (ALARA).CITATION:Black, J and Reid, D, 2017. Delivering a healthy atmosphere underground in a cost-conscious environment, in Proceedings Australian Mine Vent Conference 2017, pp 159–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D Brouwer, P Wild, B Belle

Due to the steep geo-thermal gradient in Bowen Basin area, as underground coalmines reach increased depths of extraction, the Bulk Air Cooling (BAC) requirements will increase as opposed to cooling the workplace using the ventilation means alone. One such mine has already been using a 4 MW surface BAC plant for the last six years to manage the working temperatures with reduced cooling efficiency as the mine expands. Due to the horizontal nature of the longwall mine layout, distances from the working face to intake shafts are rapidly expanding to over 6 km as opposed to the vertical mine layout of a hard rock mine. To improve the positional cooling efficiency, reduced panel pressure differentials, improved rib emission gas management, and intake dust management, small diameter intake shafts were located on the inbye end of production panels and halfway up the development panels with localised mobile small BAC plants. This paper summarises the results of extensive underground data of this innovative cooling concept for development and retreating longwall face heat management compared to a larger remote BAC plant.CITATION:Belle, B, Brouwer, D and Wild, P, 2017. The use of mid-panel ventilation shafts to improve positional cooling efficiency in a Bowen Basin longwall mine – a case study, in Proceedings Australian Mine Vent Conference 2017, pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By S M. Aminossadati, R Bagherpour, F Hasheminasab

Mine ventilation is an essential part of underground mining operations used to provide fresh and cool air, as well as to dilute and remove contaminants from the work environment. This paper presents an overview of the ventilation and gas management systems in one of the underground coalmines in Iran: Parvadeh_1 mine. The mine is located in the Tabas coalfield in the South Khorasan province. It is the only fully mechanised mine in Iran utilising the longwall retreat technique. The mine produces 1.1 to 1.3 Mt of coking coal annually. The mine ventilation system currently utilises two 630 kW exhaust surface fans. The gas management system includes surface to in seam (SIS) predrainage boreholes. The underground mine is equipped with an underground gas reticulation pipeline that is connected to a surface plant for the production of methane gas. This study shows that the ventilation and gas management systems of the Parvadeh_1 mine are in line with the standards of Australian underground mines.CITATION:Hasheminasab, F, Aminossadati, S M and Bagherpour, R, 2017. An overview of ventilation and gas management systems in an underground coalmine in Iran, in Proceedings Australian Mine Vent Conference 2017, pp 41–46 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Y Zhang, X Yi, J Deng, J Zhao, J Song

To obtain the combustion process of a coal fire, a high-temperature programmed system is used to simulate the spontaneous combustion process of fresh and weathered coals. Both fresh coal and weathered coals from Liulingou, Inner Mongolia, China, were used to examine the gas releases from constant temperature to 650°C. Moreover, gas release rate was used to calculate the characteristic temperatures. The results showed the coal samples lasted to oxidise under high temperatures, and released plenty of heat to assist self-heating. The humic acid contained inside the weathered coal went through thermal decomposition as temperature rising and generated gases. This resulted in increasing concentrations of CO, CO2, CH4, C2H4, and C2H6. Changes of CH4, C2H4, and C2H6 gases were also similar. For weathered coal, concentrations of three gases were kept in balance under low temperatures, increased rapidly with the temperature rising. After the ignition temperature, the concentration of hydrocarbon was reduced. In addition, particle size affected coal spontaneous combustion. Coal samples with less than 0.9 mm in size produced much more CO than others. This study has examined coal spontaneous combustion caused by coal weathering during mining and its impacts on self-heating and pyrolysis in the process.CITATION:Deng, J, Song, J, Zhao, J, Zhang, Y, Yi, X and Zhang, Y, 2017. Gaseous products of weathered coal during the process of spontaneous combustion, in Proceedings Australian Mine Vent Conference 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By B Leisemann, M Watkinson

Coal augering is an ideal method for recovering coal from the highwalls of open cut coalmines. Coal augering is a simple process whereby additional flights are added to the auger cutting head and auger holes are drilled at 1.9 m diameter up to 200 metres deep. Traditional monitoring was located at the mouth of the hole and if methane was encountered above two per cent, inert gas was delivered into the mouth of the hole to deplete the oxygen content at the auger cutting head below 12 per cent. The auger operator was asked the question ‘how do you know that this is the case?’ Trials were undertaken to prove that the oxygen content at the cutting head did drop below 12 per cent (the lowest limit for methane to ignite, also known as the oxygen nose point). Initial trials showed that the oxygen content in the mouth of the hole did not drop below 12 per cent and modifications were made to hold the inert gases in the mouth of the hole so that the auger flights could take this inert gas into the hole. In-hole monitoring, after completion of mining and after extracting the auger flights, showed that the atmosphere quickly returned to fresh air. In-hole monitoring was also tried during the augering process and yielded valuable results. This paper will discuss the results of the monitoring, information on the gas results obtained and the methodologies used to optimise the oxygen content at the auger face.CITATION:Watkinson, M and Leisemann, B, 2017. Inertisation of coal augering holes, in Proceedings Australian Mine Vent Conference 2017, pp 293–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By J Zanganeh, M Ajrash, B Moghtaderi

Application of thermal oxidation is considered a promising technique in reducing fugitive methane gas from ventilation air methane (VAM). A typical thermal oxidiser operates with diluted methane and converts it to less potent greenhouse gases. However, having a thermal oxidiser in the vicinity of the coalmine exhaust shaft is a major safety concern as its high operation temperature increases the likelihood of accidental fire and explosion. The aim of this study is to investigate the application and effectiveness of side venting technique in reduction of deflagration consequences caused by methane gas. To address this importance a series of experiments were conducted on a detonation tube designed and fabricated as part of larger scale VAM Abatement safety project. The experimental work was carried out into two stages: examine the flame and explosion properties in a large-scale detonation tube to get reliable data; and then design and employ a venting system into the detonation tube to verify the effectiveness and performance of the venting against the flame and explosion.Results corresponding to this study show that the side vent duct with venting coefficient magnitude of 37 had a significant influence on methane flame deflagration and the explosion characteristics. The maximum pressure rise at the detonation tube reduced approximately 20 per cent to 32 per cent by applying the side venting duct. Also, the data shows that the venting damped the pressure oscillation after the flame deflagration which eventually reduced the system instability. Finally, by applying the venting technique the expected level of damage due to the dynamic pressure reduced to the level of limited building damage.CITATION:Ajrash, M, Zanganeh, J and Moghtaderi, B, 2017. Application of side venting technique in mitigation of methane – air explosion and flame deflagration in ventilation air methane, in Proceedings Australian Mine Vent Conference 2017, pp 153–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By M Amanzadeh, S M. Aminossadati, B M. Masum, M S. Kizil, C R. Leonardi

Gas sensing systems are becoming more important in many industries such as oil, gas and mining operations. Particularly in underground coalmines, accurate and reliable monitoring of toxic and combustible gases such as methane, nitrogen dioxide, carbon monoxide and hydrogen sulfide is essential. Available conventional electrochemical sensors for gas measurements in underground coalmines suffer from shortcomings such as cross-sensitivity response, limited lifetime, high calibration cost, maintenance cost and safety. Recent studies have found that fibre optic-based gas sensors have potential to eliminate these issues. These sensors can also be used for long distance and distributed sensing of various gases, both of which are important for underground gas monitoring. The aim of this paper is to review the present underground mining gas monitoring systems and review the new generation of fibre optic-based sensing systems for use in underground coalmines.CITATION:Masum, B M, Aminossadati, S M, Leonardi, C R, Kizil, M S and Amanzadeh, M, 2017. New generation of gas sensors for underground coal mining applications, in Proceedings Australian Mine Vent Conference 2017, pp 189–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D J. Brake

There has been a strong trend over the past decade in hard rock mines towards the use of very high powered auxiliary (or secondary) fans; in many mines, the installed power for the secondary ventilation system now exceeds that of the primary ventilation system. This also reflects the trend to use two-stage auxiliary fans pushing air into a single ‘trunk’ duct that in turn splits into multiple branches with multiple outlets feeding multiple workplaces. This often produces a poor result in terms of face flows due to the high resistance, high leakage and badly managed duct outlets, as well as high fan capital and operating (power) costs, which in turn also results in a higher cost for the underground power reticulation/distribution systems. This paper explores the reasons why this trend exists and what ventilation practitioners can do to utilise less expensive systems that simultaneously deliver better workplace conditions. It includes a case study.CITATION:Brake, D J, 2017. Auxiliary ventilation design – why and how mines waste so much power on inferior systems, in Proceedings Australian Mine Vent Conference 2017, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D J. Brake

The correct specification and then selection of primary or major fans for an underground mine is a critical decision not only in terms of fan capital and operating costs, but also safety and reliability which usually has a major impact on mine production. In addition, fan manufacturers may spend tens of thousands of dollars preparing proposals for a purchase enquiry for primary fans especially where they have complete responsibility for the installation (turnkey projects). There are many good reasons to thoroughly and fairly adjudicate fan tenders. This paper describes the process to achieve this starting with the initial fan specification through to the final award.CITATION:Brake, D J, 2017. Fan specification and tender adjudication for mine ventilation engineers with particular reference to turnkey projects, in Proceedings Australian Mine Vent Conference 2017, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D Chalmers, C R. Ward, B B. Beamish

Coal workers’ pneumoconiosis (CWP) has re-emerged as a major concern in the Australian coal mining industry. Harmful effects from coal dust inhalation have been well documented, but the underlying causes and mechanisms of CWP are still debatable. Research conducted in the USA has proposed a plausible link between the presence of pyrite in coal and the prevalence of CWP. Reactive pyrite in coal oxidises under ambient mine conditions to produce various iron sulfate minerals such as melanterite, rozenite, roemerite and szomolnokite. Rapid reaction rates are promoted by the form (size and morphology) of the reactive pyrite present, which provides both increased surface area and increased porosity for easy air access to reaction sites. The products formed from reactive pyrite oxidation are often needle-like crystals with thicknesses in the order of 1–2 µm (eg melanterite and rozenite) and prismatic crystals with thicknesses less than 5 µm (eg roemerite) have been recorded. The densities of these minerals are significantly less than quartz, which makes them prone to becoming airborne with the normal coal dust. In fact, the mix of these mineral salts is commonly referred to as ‘fairy dust’ by mine workers due to the way they can become entrained and sparkle in the mine ventilation air, particularly if they occur in the upper part of a seam that is forming a coal roof. Examples are presented of the various products of reactive pyrite oxidation found in three Australian coal samples, which provide evidence of the physical and chemical mechanisms that would support the USA findings, particularly in terms of a source of bioavailable iron leading to increased inflammatory stress response.CITATION:Beamish, B B, Ward, C R and Chalmers, D, 2017. Products of reactive pyrite oxidation in the mine environment – implications for coal workers’ pneumoconiosis, in Proceedings Australian Mine Vent Conference 2017, pp 87–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By A S. Derrington

There are several long-standing rules of thumb that are often quoted in mine ventilation studies. They include airway ‘carrying velocities’ and the critical upcast air velocity range that must be avoided to prevent a water blanket forming. Quoting these rules of thumb may lend an air of legitimacy to a ventilation design, and allow the design engineer to avoid having to study a problem from first principles. But how valid are these shortcuts in today’s rapidly changing world? This paper summarises research into the genesis of several commonly quoted rules of thumb. It finds that they were very specific to the local conditions, practices and economics at the time they were developed. It also presents examples where applying these rules of thumb outside of their original context can lead to unexpected and erroneous results.CITATION:Derrington, A S, 2017. Ventilation rules of thumb – friend or foe? Focusing on design upcast air velocities for shafts and raise bores, in Proceedings Australian Mine Vent Conference 2017, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Ádria Rocha Corrêa

Durante a solidificação de ligas metálicas, o produto fundido se contrai, o qual provoca o surgimento de espaçamentos vazios na interface metal/molde chamados de “gaps”. Estes gaps causam o aumento da resistência térmica influenciando em toda a cinética da solidificação. A transferência de calor durante a solidificação depende do conhecido parâmetro chamado de coeficiente global de transferência de calor ( hg). Este parâmetro é representado pela equação do tipo: hg =C.t-n, a qual indica que a eficiência térmica na interface metal/molde decai com o tempo. Muitos parâmetros podem influenciar o coeficiente global de transferência de calor (hg), neste estudo, os percentuais de Sn em ligas do sistema Al-Sn são analisados (10,20,30 e 40%Sn). Portanto, o principal objetivo deste estudo é propor uma relação matemática que descreva, para o sistema Al-Sn, a evolução hg em função do teor de Sn. A relação matemática foi obtida através do método dos mínimos quadrados

Aug 17, 2017

By Julián Andrés Ortiz González

Este estudo apresenta novos resultados que comprovam a confiabilidade e a repetibilidade das medições de cargas de abertura de trincas de fadiga obtidas em estudos anteriores [1,2], que foram usadas para questionar a hipótese proposta por Elber em 1970 de que a força motriz das trincas é a gama efetiva do fator de intensidade de tensões (?Kef). Para isto, dois corpos de prova DC(T), um fino com 2 mm e o outro grosso com 30 mm de espessura, foram usados em ensaios de propagação de trincas por fadiga sob ?K e Kmax quase constantes, para simular condições dominadas por tensão ou deformação plana. Medições redundantes de ?Kef foram feitas usando uma série de extensômetros colados ao longo do ligamento residual à frente da ponta da trinca, por outro extensômetro colado na face traseira do DC(T), e por um sistema independente de correlação digital de imagens (DIC), que mede o campo de deslocamentos na face do espécimem. As cargas de abertura medidas pelos três sistemas independentes foram similares, comprovando assim que suas variações significativas observadas durante o crescimento da trinca são metrologicamente confiáveis. Este resultado comprova que a propagação daquelas trincas por fadiga não foi controlada por ?Kef. As consequências desta conclusão são detalhadamente discutidas neste trabalho.

Aug 17, 2017

By Laís Ávila de Oliveira Silva

A aplicação de ligas de NiTi como biomateriais exige que sua superfície tenha um excelente acabamento final, para garantir a alta resistência à corrosão e a biocompatibilidade. O polimento eletrolítico é um processo capaz de diminuir as imperfeições da superfície, sem alterar as propriedades do material, e de formar uma fina camada protetora de TiO2. Nesse estudo, foram realizados eletropolimentos em fios superelásticos e com memória de forma, usando dois eletrólitos ácidos distintos. A partir dos resultados obtidos, foi possível concluir que a solução de ácido sulfúrico produz superfícies mais homogêneas do que o de ácido perclórico, para os mesmos tempos de polimento, e se apresenta como uma boa alternativa para o tratamento superficial de ligas superelásticas e martensíticas de para sua aplicação como biomateriais.

Aug 17, 2017

By Aline Aguiar Lopes

A piora na qualidade dos minérios de ferro tem levado as empresas a adaptarem seus processos a novas condições de qualidade das matérias-primas, surgindo assim a necessidade de desenvolver estudos que auxiliem as tomadas de decisão. Esse trabalho avaliou a influência da qualidade do sínter e da composição da carga metálica na zona coesiva do alto-forno através dos parâmetros de amolecimento e fusão. A importância de se obter informações sobre a zona coesiva se deve principalmente ao fato de nessa região ocorrer a maior parte da perda de carga no interior do alto-forno. Cinco amostras de sínter de qualidades químicas distintas, produzidas nas sinterizações da CSN (Companhia Siderúrgica Nacional), foram selecionadas e caracterizadas para esse estudo. Os ensaios de Amolecimento e Fusão foram realizados no Centro de Tecnologia de Ferrosos da Vale através de um acordo de cooperação técnica entre as empresas. Os resultados obtidos mostraram que as técnicas utilizadas são adequadas para avaliação das propriedades em altas temperaturas, fornecendo dados importantes para a interpretação do comportamento da carga metálica no interior do alto-forno, como espessura e posicionamento da zona coesiva, permeabilidade e redutibilidade da carga, indicando assim, a composição da carga metálica de melhor desempenho para o alto-forno.

Aug 17, 2017

By Juan Garcia de Blas

O presente trabalho aborda o desenvolvimento de liga titânio-nióbio obtida por metalurgia do pó no qual foi introduzida uma operação de extrusão angular em canal (Equal Channel Angular Pressing - ECAP) com o propósito de promover uma consolidação que favorecesse a homogeneização na etapa posterior de sinterização. Após o processamento o material foi caracterizado por microscopia ótica e microscopia eletrônica de varredura (MEV/EDS). Os resultados preliminares indicaram a importância da redução do tamanho das partículas de nióbio.

Aug 17, 2017

By Pedro Augusto Silva de Lima

As ligas do sistema Cu-Al-Ni sofrem Transformações Martensíticas Reversíveis (TMR) e podem apresentar Efeitos Não Elásticos, incluindo o Efeito de Memória de Forma (EMF). Elas podem ser utilizadas nas diversas áreas e são promissoras para substituir ligas do sistema Ni-Ti. Neste trabalho foram estudadas três ligas distintas: monocristalina e policristalina Cu-Al-Ni e policristalina Cu-Al-Ni-Mn-Ti, dando atenção a análise da estrutura e comportamento mecânico, em seu estado inicial e após tratamento de betatização. Nas três ligas foram identificadas as fases martensitas ß1 e Y1e as fases R e ß1. A liga Cu-Al-Ni-Mn-Ti ainda apresentou o composto Cu2AlTi. Durante a deformação, as três ligas sofreram TMR, induzidas por tensão, com reorientação das fases envolvidas. O tratamento de betatização aumentou a plasticidade, sendo mais notável na liga policristalina Cu-Al-Ni. A liga Cu-Al-Ni-Mn-Ti se mostrou como a mais frágil, sofrendo a fratura antes de alcançar 10% de deformação. A liga monocristalina se mostrou a mais promissora para realizar EMF, revelando maior deformação armazenada no patamar de pseudoescoamento.

Aug 17, 2017