Search Documents

By G. Viggiani, J. Bel, H. Wong, N. Losacco, D. Branque

"Within the framework of the European project NeTTUN, the Laboratory of Civil Engineering and Building Sciences of ENTPE in Lyon (France) is in charge of a large experimental campaign to investigate the impact of tunneling on neighbouring piled structures. For this study, an original reduced-scale (around 1:10) physical model of EPBS is used. This ""1g"" laboratory model is able to reproduce the main features of the excavation method. For this new experimental program, the miniature EPBS advances inside a large tank filled with a model soil (dry sand), in which instrumented piles were pre-installed. In this paper, the authors describe briefly the original 3D device and present results concerning the impact of tunneling on a single pile located above the tunnel. Different tunneling face pressure are studied in connection with the practice. Machine parameters, pile solicitations and stress-strain behavior of the soil mass monitored under real time conditions are discussed. INTRODUCTION When tunnels are constructed in urban areas, they often come close to pre-existing structures, such as pile foundations. Perturbations of tunnel construction on these neighbouring structures must be considered during design and construction of the tunnel. Ground movements due to tunnelling may induce bending moments, lateral and vertical loads, settlements and lateral deflections in the piles, which may lead to structural damage or failure of the piles or the supported structure. The interaction between piles and a tunnel in construction is a complex three dimensional problem. To date, several experimental approaches have been carried out to analyse the effects of tunnelling on piled foundations (Bezuijen et al., 1994, Loganathan et al., 2000, Jacobsz et al. 2004, Lee and Basset, 2006, Marshall and Mair, 2011, ). These different studies carried out in the laboratory on 1 g or centrifuged models aim at a better understanding of tunnel - piles interaction and a quantification of the influence of each dominating parameter on the structural responses. Parameters like foundation type (single pile, group of piles) and geometry, relative tunnel – pile position, volume loss induced by tunnelling, ground characteristics, pile loading history were considered. However, most of these experiments were carried out under plane strain conditions by modelling the volume loss due to tunnel excavation by decreasing the tunnel diameter or the radial support pressure. As a result, these models do not adequately account for the variations of settlements both in the longitudinal and the transverse direction, which can induce significant flexional and torsional effects on the structures. These effects are particularly critical and detrimental in the case of historical monuments."

Jan 1, 2016

By P. James

"INTRODUCTION Control of target stream acidity is widely used in MIW (mining influenced water). Tailoring pH (a measure of acidity) finds application for controlling key chemistry in both process and waste streams. Traditional lime addition for neutralization and precipitation is most often used but has high reagent costs and results in large amounts of mixed metal sludge requiring costly disposal. A new adaptation of BPS’s patented DEMET™ technology (Dynamic Electrolytic Metal Effluent Treatment) platform offers a potentially improved and “reagentless” alternative to traditional chemical addition for pH adjustment. Electricity rather than chemical addition utilized in BPS’s proprietary approach controllably tailors target stream pH. The method offers a simple, low-cost processing technique yielding cleaner treatment chemistry. BPS’s “green” approach may yield lower operating (OPEX) and life cycle costs and significant reductions (up to 50%) in sludge generation compared to conventional lime treatment. It can also allow new opportunities to generate revenue via selective recovery of valuable processing byproducts. Specific savings and revenues depend on the target site chemistries, details, and processing goals. A more detailed discussion of the process and its operational principles may be found in Reference One.[1] Here application of the BPS treatment to POx (Pressure Oxidation) leaching as an alternative to traditional chemical addition is examined. An example operation process flow for gold mining is considered.[2] Promising processing points for potentially replacing conventional processes with DEMET are noted. The possibilities for lowering OPEX costs, lessening sludge creation, and capturing various valuable byproducts and residuals are examined. Financial life cycle benefit estimates of the principal gains provided by DEMET application to the example operation are noted. Extension and generalization of the analyses to a wider range of scenarios is explored."

Jan 1, 2016

By Steven W. Hunt

"A paper called “Global Experience with Soft Ground and Weak Rock Tunneling under Very High Groundwater Heads” was presented at the North American Tunneling 2006 conference (Holzhäuser et.al 2006). It summarized global experience with earth pressure balance (EPB) and slurry shield tunneling on nine projects that encountered groundwater heads ranging from 6 to 11 bar. Since then, additional projects have been completed with groundwater heads ranging from 7 to 15 bar. Of these, the high pressure tunneling experience on the Lake Mead Intake No. 3 project in Nevada and on the Eurasia Tunnel (Istanbul Strait Crossing) had the greatest lengths of tunneling at face pressure over 7 bar. Experience with sustained pressurized face tunneling at groundwater heads over 7 bar and risk management observations are the focus of this paper. INTRODUCTION High groundwater head, particularly at 7 bar or more, is a major challenge when tunnelling in high permeability ground and on drives long enough to require cutter changes. It has a strong impact on design and operation of Tunnel Boring Machines (TBMs) in order to protect the main bearing from contamination, prevent excessive groundwater inflow, ensure face stability and enable access to the cutterhead and excavation chamber for maintenance. During the past 20 years, TBM manufacturers and suppliers have made tremendous improvements that allow tunneling at groundwater pressures to 17 bar or more. The most significant risk with high pressure tunneling is generally that of excavation chamber access and potentially the cutterhead for cutter changes, cutterhead repairs and TBM maintenance. Hyperbaric interventions are possible and safety variances have been approved for saturation dive interventions at pressures as high as 17 bar (Lake Mead Intake No. 3). While high pressure hyperbaric intervention equipment is available and safety approvals can be obtained at many locations, few contractors consider the cost and risk of hyperbaric interventions over 7 bar to be acceptable as the primary means of excavation chamber access. Experience with high pressure tunneling prior to 2006 was summarized in a paper entitled “Global Experience with Soft Ground and Weak Rock Tunneling under Very High Groundwater Heads” (Holzhäuser et.al 2006). That paper provided information on 9 projects: South Bay Ocean Outfall, San Diego; Channel Tunnel (French Side), France; Storebaelt Tunnel, Denmark; 4th Elbe Tunnel, Germany; Wesertunnel, Germany; Westerschelde Tunnel, Netherlands; St. Petersburg Red Line, Russia; Nara Prefecture Water Conveyance Tunnel, Japan; and Tokyo Wan Aqua Line Tunnel, Japan – see Table 1."

Jan 1, 2016

By Michael N. Maltezos

"There is certainly no argument that LED lighting systems have taken a strong foothold in the lighting marketplace over the last several years. This has even proven true in the world of transportation and transit lighting, for which new LED cobra head style luminaires are replacing traditional HID cobra head luminaires on North America’s roadwaysand linear LED light fixtures are replacing conventional linear fluorescent light fixtures in North American rail transit facilities. However, LED technology has taken a while longer to penetrate the very specific market of vehicular tunnel lighting in this continent. Though both the New York/New Jersey Holland and Lincoln Tunnels have recently been retrofitted with LED lighting, and an LED Lighting RFP is currently out for Boston’s Central Artery Tunnels, very few vehicular tunnels in North America to date have been illuminated with LED light fixtures. This is largely because cost effective LED lighting, that met our typically stringent tunnel lighting standards, was until recently simply unattainable. However, with the rapid advances in LED technology over recent years, owners and specifiers of North American tunnel lighting projects have finally begun to adopt LED lighting systems as the norm. In fact, a recent Lux Fit/Yole Development “LED in Road and Street Lighting Report” stated that “LED luminaire growth will be driven firstly by tunnel lighting, and then relayed into highway, road, residential and amenity lighting applications starting in 2014.” 1 Our highways are continually becoming more congested. As a result, Provincial and State Departments of Transportation (DOTs) are constantly looking for innovative ways to improve traffic flow. One way DOTs are now helping to ease congestion is by expanding the use of tunnels and long underpasses in large interchange reconstruction projects. With less available right-of-way to work with, and the high costs of maintaining elevated bridge structures over the years, it often makes more sense to “go under” (rather than over) the traffic congestion points. With the addition of these new tunnels and long underpasses comes the issue of proper illumination within these structures, for a safe and efficient driving task. DOTs use recommended lighting practices and guidelines for highway lighting, which include specific criteria for tunnels, set by either the Illuminating Engineering Society of North America (IESNA) or the American Association of State Highway and Transportation Officials (AASHTO). However, both IESNA and AASHTO point out that these recommended practices and guidelines are not a mandate, and DOTs are free to make their own decisions about lighting criteria. Accordingly, effectively illuminating tunnels is often times a challenge. This paper will examine the key considerations of the tunnel lighting application in generalas well as what LEDs now bring to the table and how, accordingly, traditional lighting technologies will be phased out in the future illumination of tunnels."

Jan 1, 2016

By Tyler A. Dawson, Ryan P. Butler, Timothy Gualandri, Jason R. Edberg

"In the early 1920’s, the City of Tulsa, Oklahoma constructed an approximately 8,238-foot long tunnel, the Tiawah Tunnel, through bedrock. Voids behind the concrete tunnel liner were detected via probe drilling in early 2000 as part of an interior visual condition assessment. In 2012 and 2015, conditions along the entire tunnel were efficiently assessed through geophysical investigation using ground penetrating radar (GPR) along the inner tunnel crown and at various select locations within the tunnel. Fifty-seven (57) potential voids, extending up to 19 inches in depth and 12 feet in width, were detected with 1,000 MHz GPR and confirmed through probe drilling with approximately 80% accuracy. GPR proved to be an efficient and reliable technology for void detection behind concrete tunnel lining. This paper highlights the geophysical investigation and how geophysical efforts were combined with other investigation efforts to definitively determine the presence of voids outside of the tunnel lining.INTRODUCTION The city of Tulsa, Oklahoma has a population of about 400,000 people. The original source of water for the city was the Arkansas River. The first pumping operation provided untreated water to homes and businesses in 1904. The residents of Tulsa found this water to be unacceptable due to the high levels of salt and gypsum present. As the city grew, land and storage/treatment facilities were acquired in order to obtain and distribute a more suitable raw water. The raw water needs for the city are currently satisfied by transport and treatment of about 100 million gallons per day (MGD) of water from surface water sources. Water is transported many miles from Spavinaw/Eucha and Oologah lakes to Yahola Lake and the Lynn Lane Reservoir (totaling over 3-billion gallon capacity). From here, the raw water is treated and transported to the various customers (City of Tulsa 2015). The Tulsa Metropolitan Utility Authority (TMUA) is responsible for the operation and maintenance of the raw water transport system."

Jan 1, 2016

By Karin Bäppler

"When considering large-scale infrastructure projects worldwide special attention has to be paid to the large diameter tunnel construction projects that were successfully completed in the Southern Hemisphere. The projects that are highlighted in this paper are large-scale infrastructure projects in the sector of transport. In focus are four road tunnel projects that were constructed in Australia and New Zealand using mechanized tunnelling technology. The tunnel boring machines (TBMs) that were reliably applied to these four major projects all exceed the bore diameter of 12 meters. These TBMs are therefore in the range of large to very large diameter TBMs. The technology used demonstrates state of the art technology with tailored tunnelling technology adapted to the specific project demands. Two Double Shielded Hard Rock TBMs (Ø 12.35 meters) were used for the construction of the Clem Jones Tunnel in Brisbane crossing beneath the Brisbane River and these two machines have been reused for the excavation of a 4.3km long two-lane highway tunnel for Legacy Way in Brisbane creating a new traffic artery towards the city centre. Two EPB Shields (Ø 12.48 meters) excavated and lined the twin-tube road tunnel for the Brisbane Airport Link. Excavation diameters in excess of 14 meters, such as the Earth Pressure Balance Shield (Ø 14.41 meters) involved in the Waterview Connection Project in New Zealand, are understood in the tunnelling industry as very large diameters. The machine is customized to the requirements and subsurface conditions of Auckland. The paper spotlights the large to very large diameter TBMs that were used and focuses on the comprehensive solutions developed by the machine manufacturer to provide a system with benefits for the contractor especially for the Waterview Project. INTRODUCTION Extensive large-scale road infrastructure projects like the ones implemented in Brisbane (Australia) and currently under construction in Auckland (New Zealand) show the tendency of today’s infrastructure construction projects. Functional infrastructures need to be put in place to cope with the demand of mobility and flexibility of people living in cities and metropolises. Impact during construction work to people or environment has to be kept as low as possible to ensure the quality of life is not disrupted."

Jan 1, 2016

"An atmospheric process for the synthesis of scorodite(DMSP®)has beendeveloped,in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. Under optimum conditions, the synthesized scorodite (FeAsO4?2H2O) was well crystallizedand the crystals were faceted; the particle sizes were as large as 15 to 20 µm. In thisstudy, iron (II) sulfate heptahydrate (FeSO4·7H2O), arsenic (V) acid (60mass%H3AsO4) solution, and distilled water were used to prepare the original experimental solution (700 ml), in which the contents of Fe(II) and As(V) were 55.9 g/L and 50.0 g/L, respectively. The effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas injectionrate, temperature, and the initial pH of the solution, on the size and shape of the scorodite particles wereinvestigated. From the experimental results, the changes in the shape of the scorodite particles wereclarified for each synthesis condition.INTRODUCTIONDOWA has developed a processfor synthesizing well-crystallized scorodite (FeAsO4•2H2O). Theprocess is named andtrademarked as DMSP® (Fujita et al., 2008; Fujita et al., 2008; Fujita et al., 2009; Fujita et al., 2009; Fujita et al., 2009, Kubo et al., 2010). In this process, oxygen gas is injectedinto a sulfuric acid solution containing large amountsof As(V) and Fe(II). Facetedscorodite crystals as large as 15–20 µm weregeneratedthrough the pre-formation of a gel-like precursor. However, it is known that the synthesized scorodite particles become smaller and more aggregatedwhen the synthesis conditionsdeviate from the optimumconditions.In this study, the effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas flowrate, temperature, and initial pH of the solution, on the size and shape of the scorodite particles were investigated. The experimental resultsclarified the changes in the shape of the scorodite particles for each synthesis condition."

Jan 1, 2016

By Enrique Albarrán, Julian Hernández

"In 1942 The “Presa Mixcoac” dam was built, along with 15 other dams, to control the rain fall waterin the mountains west of Mexico City. Mexico City’s population at that time was around 1.5 millionpeople, and the dam was way out of the city."

Jan 1, 2016

By Marc Tardif

"The way alarm information is provided to an operator can make a huge difference in the minutes following an upset. Process alarms are often looked at as a way to help avoid catastrophic failure and serious accidents. But knowing that mineral processing is so energy consuming and that raw material is not consistent, all small upsets should also be seen as a catastrophe because they can have significant impact on product cost and quality.This paper will demonstrate how it is possible to use data from process alarms to provide operators with real time, value added information that will help them take the right decision at the right time and in turn, reduce unplanned downtime by 20 to 80% and incidents by up to 50% (number and cost),and optimize energy and capacity usage.In the era of Big Data, living in a world where we are submerged with information, one of the biggest challenges is to find the right information at the right time.Alarm rationalization projects will often focus on alarm quantity, but alarm quality is also very important. It is possible, by following a simple 6-step process to turn “alarms” into truly valuable information for operators. Based on known standards (ANSI/ISA 18.2 and EEMUA 191), this process will capture the knowledge of the best and most experienced operators and process engineers, and make it readily available to everyone, right on time, when it matters the most.INTRODUCTIONWhen spending some time in a modern control room, it is easy to notice the huge quantity of information that is available to the operator. Modern operation stations feature multiple screens with HD capability. These screens display information like process display, history trends, alarms and events list, maps with geo-located information, images from live cameras, etc. However, it is harder to assess whether all this information is really helping operators: Is all the information relevant? Are process screens overcrowded? Is the information easy to understand? Does the operator know what to do with all the information? Are there too many alarms?"

Jan 1, 2016

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By M. Birdsell

"Sustainable long-term restoration requires adequate planning and preparation, implementation, and measurement goals to monitor success associated with restoring sites to pre-disturbance levels of ecological health. The Buckhorn Mountain Mine riparian habitat restoration project has been a multi-year endeavor with a variety of restoration techniques implemented by Kinross Gold/Crown Resources Corporation. INTRODUCTION The Buckhorn Mountain Mine procured mitigation lands during the permitting process to be set aside for long-term restoration. A portion of this mitigation land included three aquatic habitat mitigation parcels; a spring and wetland complex and two stream and riparian corridors. These properties were historically used for agriculture purposes and livestock grazing. During initial permitting, habitat monitoring and mitigation plans were created to help guide restoration, and provide measures for success. Various techniques and adaptations have been implemented on the properties since 2007, and continued efforts are being implemented annually to ensure the long-term success of the project. Field measurements are collected annually to ensure mitigation objectives are being met, and provide opportunity to modify restoration efforts when necessary. MATERIALS/METHODS Restoration efforts have included implementation of several methods including livestock exclusion, treatment of state and locally listed noxious weed species, installation of regionally sourced riparian plant species and local stock willow cuttings. Annual mechanical and herbicide treatments for noxious weeds have been conducted annually. Efforts to control reed canarygrass (Phalaris arundinacea) have been implemented since 2013; methods include mechanical and herbicide treatments. A combination of methods has been employed to help aid restoration of native species within the riparian corridor, and increase survival of planted species, including weed matting and browse barriers to aid riparian planting success. Instream planting of local stock willow have also been employed to increase stream vegetative cover and provide long-term bank stabilization. Most recently, a perched culvert near one of the properties has been replaced with an aquatic life passable culvert designed to aid in the upstream migration of fish species into the stream system. Efforts to provide increased fisheries into upstream portions of the system and aid in restoration of stream bed and bank have been employed to increase the ecological value downstream of the replacement. In addition to efforts completed by the client to provide restoration efforts, a local non-profit organization, in conjunction with the client, installed beaver dam analogues (BDAs) in the fall of 2014. These structures are intended to raise water levels along stretches of incised channel in an attempt to flood historic off-channel floodplain"

Jan 1, 2016

By Thomas Konstantis, Spyridon Konstantis, Panagiotis Spyridis

"Tunneling and Underground works are unequivocally subject to a diversity of inherent uncertainties associated with the geotechnical, hydro-geological and environmental regime that surrounds them. On many occasions, these uncertainties can provoke loss events of considerable consequences. The present contribution elaborates on losses that the insurance market has suffered in the recent years, following a construction failure event. These losses are being considered and analysed on a quantitative basis through evaluation of cost related data, with explicit discretization of the applied construction methodology and of the subsequent developed failure type since both of which are considered of major importance. Given the identified persistence and regularity of some loss-contributing factors, recommendations are provided on the basis of a proactive risk engineering management approach that are envisaged to reinforce the understanding of project risks and alleviate the incurred insurance cost. 1 INTRODUCTION The underground construction sector has always been a very challenging area for all involved parties, including the insurance market. Main reason for that remains the uniqueness of the uncertainties sources and the subsequent inherent risks that the tunneling and underground projects are exposed to. In many instances, these risks materialize, leading to loss events with substantially high impact on reinstatement cost and incurred delays, which depending among others on the insurance coverage will have to be bared by the Insurance market. In the recent decades and as the tunneling industry boomed and expanded with many major and significant projects undertaken around the world, the insurance market was faced with additional challenges. Increased competition during tender coupled with the scale and complexity of the projects and politically driven decision making exerted pressure on the project timelines, completion dates and budget. The pressure for on-time or even early project completion- to avoid liquidated damages or achieve bonus payments, respectively- along with cost reduction efforts and the incentive for innovative failure events. That, in turn, put additional pressure on the Insurance market which had experienced a significant amount of losses with substantial cost. One of the triggered mitigation actions was the introduction of the Code of Practice for Risk Management of Tunnel Works (ITIG, 2006 & 2012; MunichRe 2006, Wannick, 2007, Spencer, 2008, Adeyemo, 2011)."

Jan 1, 2016

By J. O. Claassen

"A study conducted at 22 operating mines in the southern African region indicated that each mine employs about five management and improvement methods with roots in the manufacturing industry. All respondents reported the implementation of cost-saving initiatives, whereas 80% of the mines are affected by restructuring. TQM, Six Sigma, BPM, and TOC were found to be the most prevalent manufacturing management and improvement methods used. A mechanistic vs systemic evaluation of the suitability of these methods to bring about positive change in the industry suggested that complex, ever-changing mining systems are better served by a systemic flow-based approach, which is embedded in methods such as TOC, JIT, TPS, and Lean Production. These methods, however, lack industry presence, possibly because they do not effectively deal with the unique challenges associated with the mining environment. It is argued that successful mining business management and improvement depends on management’s ability to deal effectively with mining industry-specific requirements, the integration of the geologymining- plant system, and the implementation of systemic flow-based principles in all aspects of mining. IntroductionThe study aims to explore the use of manufacturing management and improvement methodologies in the southern African mining industry. Considering the unique challenges associated with mining operations, attention is given to the applicability of the most commonly used manufacturing methodologies in the tactical, operational, and strategic environments. The article endeavours to stimulate more research and debate in an unexplored field of study."

Jan 1, 2016

"The seventh annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held last February at the SME Annual Conference & Expo in Phoenix, AZ. A total of 21 students entered the poster competition. The students were required to submit one-page abstracts, which were reviewed by the judges, after which they prepared posters to display their work. A panel of judges went to each student and listened as the student explained his/her research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. Recognizing the effort required to participate, the MPD provided monetary rewards to all participants. First place received $1,000; second, $500; and third through seventh, $200. All remaining entrants received $100 each. The winners have their abstracts published in this issue of Mining & Metallurgical Processing. As in past years, there were separate levels of competition for undergraduates and graduates.Now for the winners:Graduate winnersJoseph Halt won first place for research on the use of additives to starch binders to create iron ore pellets. Vivek Agarwal received second for working on using solvent extraction to concentrate lanthanum. Jordan Rutledge placed third for utilizing tannins to depress calcite in fluorite flotation. Fourth through seventh places were Vu Truong, Jacob McDonald, Hunter Sceats and Doug Schriner.Undergraduate winnersLaura Nugent won first place for using high-frame-rate cameras to follow bubbles as they moved from the pulp to the froth in flotation cells. Taylor Graham earned a second-place finish by researching how to acid leach low-grade manganese carbonate.Although its cliché to say everyone’s a winner, everyone can benefit from attending the MPD Student Poster contest. All the students were able to display their work to potential future employers, and industry professionals could talk to the up-and-coming engineers. Next year, there will be another competition for more posters and networking, so get ready to attend.Thank you to all the students for participating; Lisa Schlink for chairing the session; the judges, Aaron Noble, Debra Switzer, Mohammad Rezaee, Nick Gow and Ren Bryce, for evaluating the abstracts and posters; and the MPD sponsors for supporting the competition. This has only been successful with the input of all three groups. Engineering iron ore pellets to reduce their dustinessJ.A. Halt and S.K. KawatraGraduate student and professor and chair, respectively, Department of Chemical Engineering,Michigan Technological University, Houghton, MI, USAIntroductionIron ore pellets are hard spheres made by agglomerating iron ore concentrate and binders. Pellets are the preferred ironbearing feed for blast furnace ironmaking. Starch has been proposed as a binder because it has good adhesive properties, does not contaminate pellets and is relatively cheap. However, starch binders typically lead to weak pellets with rough surfaces, and these can cause high levels of dust within process equipment and when pellets are handled and shipped (Halt and Kawatra, 2014). Our research shows that by adding a small quantity of other additives, pellets made with starch binders become smooth and strong. The newly designed binder leads to significantly lower levels of fines when pellets are handled."

Jan 1, 2016

By Bo Kyung Sim, Dae Young Kim, Jae Won Lee, Ebrahim Farrokh

"The contract C931 of the downtown line 3 (DTL3) mass rapid transit system of Singapore includes half a kilometer twin tunnels running between Mattar and Macpherson stations. An EPB TBM of 6.6 m diameter was used to excavate both of these tunnels. The tunnels pass predominantly through a very stiff silty/clayey fine to coarse sand from the Old Alluvium Formation. In this paper, TBM selection procedure, TBM performance evaluation, and some of the tunneling operation challenges with the TBM in the Old Alluvium Formation are discussed. In this regard, soil conditioning trial tests were performed to resolve the clogging issue and low TBM performance. Thorough TBM operational data analysis was performed to detect high soil abrasivity, backfill grout leakage, and foam nozzle clogging. The results of some of the applied modifications are also discussed to show their effects on the TBM performance improvement. Finally, some of the challenging TBM design specifications are also discussed. INTRODUCTION Tunneling and underground construction in Singapore has been increased in the last 30 years due to the demand for public transportation systems and the limited space above the ground for the infrastructure development. Downtown Line Stage 3 (DTL3) Mass Rapid Transit (MRT) system has 21 km total route length and consists of 16 stations. DTL3 Contract C931 runs between Mattar station and MacPherson station. The construction works in this contract include twin bored tunnels of 6.6 m diameter and 450 m length and a TBM launch shaft of nearly 30 m depth. The tunnels run in urban area below Kallang Paya Lebar Expressway tunnel (KPE), Kallang River Canal, and Circuit Link. Figure 1 shows the alignment of the tunnels in between two subway stations. The tunnels were excavated by an earth pressure balance (EPB) tunnel boring machine (TBM) through the Old Alluvium (OA) formation, a challenging geological formation in the sense of its abrasivity and stiffness. The Old Alluvium Formation mostly includes stiff to very stiff clayey and silty sand. The soil is un-weathered cemented to semi-cemented dense, mainly with a low permeability coefficient of 10-7 m/s and high SPT values (almost 100). The soil is classified as “very high abrasive” according to NTNU SAT test classification (SAT value of 15 to 42). The construction of the first tunnel drive was slowed down due to a number of factors related to soil conditioning and TBM operation. In this regard, a thorough analysis of the TBM operational parameters from the excavated sections was performed to identify the problems in time to prevent unwanted construction delays in the subsequent sections. In the following sections, a brief overview of the criteria used for TBM selection is presented at first. Then, the results from the analyses and tests performed to assess soil conditioning, grout leakage, and soil abrasion are presented. The last section discusses some of the tunneling design features that challenged the TBM operation in this project."

Jan 1, 2016

By Michel Épiney, COREM, Mario Drapeau, Caroline Olsen, Claude Bolduc, Benoit Levasseur

"Several metal sulfide minerals (such as copper, zinc and iron), generally abundant in precious metal-containing ores, are known to dissolve during the cyanidation process. These unwanted reactions consume a significant amount of cyanide and oxygen, which is required for the extraction of gold and silver. Leaching kinetics of sulfide minerals are very fast in contact with oxygenated cyanide solutions. Therefore, the solution quickly becomes charged with oxidation products that are mostly metal ions, metallo-cyanide complexes, metal oxides and other sulfur species including thiocyanate, sulfides, polysulfides, thiosulfate, sulfites, sulfates, etc. COREM’s Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during pre-oxidation and cyanidation. The effect of pre-treatment under ozone was investigated using an industrial pulp recreated from process water (charged with thiocyanates) and homogenized flotation tailings material from Agnico Eagle's LaRonde mine. In terms of mechanisms, the ozone treatment provides a complete deactivation of the material surface (characterized by EDTA extraction) and the solution (characterized by Ionic chromatography). This resulted in a lower reactivity of sulfide minerals that led to substantial gains in terms of consumption of cyanide and thiocyanate formation during the cyanidation process. The ozone-pre-treatment edges the classical pre-oxidation treatment (such as oxygen, hydrogen peroxides, etc) providing a quicker deactivation of the sulfide matrix and higher reagent savings in subsequent cyanidation process.INTRODUCTIONThe presence of sulfur in the process of gold leaching by cyanidation is a major drawback to optimizing the reagents consumption with suitable operating conditions. The coexistence of sulfide mineral species, such as pyrite, chalcopyrite, pyrrhotite or sphalerite along with the gold-bearing ore have, indeed, a negative impact on the extraction of precious metals by cyanidation (Bayat et al., 2003), (Azizi et al., 2010). These minerals are known to dissolve with cyanide under alkaline conditions and release in the slurry different kinds of sulfide by-products like polysulfides, thiosel, sulfite and sulfate (Seal II & Hammarstrom, 2003) (Breuer et al., 2008a), (Marsden & House, 2006) (Ghasemian Langeroudi et al., 2013). Once these sulfide by-products are released in solution they react with cyanide to form thiocyanate (Marsden & House, 2006) (Breuer et al., 2008b). The consequence of the dissolution of these cyanicides, is a significant increase in cyanide consumtpion as well as a slow-down of gold extraction."

Jan 1, 2016

By Jimenez Leon, Christopher Newman, Boede Gabriel, Zacharias Agioutantis

"Ground movements due to longwall mining operations have the potential to damage the hydrological balance within as well as outside the mine permit area in the form of increased surface ponding and changes to hydrogeological properties. Recently, the Office of Surface Mining, Reclamation and Enforcement has completed a public comment period on a newly proposed rule for the protection of streams and groundwater from adverse impacts of surface and underground mining operations (80 FR 44435). With increased community and regulatory focus on mining operations and their potential to adversely affect streams and groundwater, there is now a greater need for better prediction of the possible effects mining has on both surface and sub surface bodies of water.As mining induced stress and strain within the overburden is correlated to changes in the hydrogeological properties of rock and soil, this paper investigates the evaluation of the hydrogeological system within the vicinity of an underground mining operation based on strain VALUES (calculated through a surface deformation prediction model. Through accurate modeling of the pre- and post-mining hydrogeological system, industry personnel can better depict mining induced effects on ground water flows through the overburden material aiding in the optimization underground extraction sequences while maintaining the integrity of surface and subsurface bodies of water.INTRODUCTIONThe utilization of high-recovery underground mining methods, such as longwall or high-extraction room-and-pillar operations, have the potential to cause adverse impacts to both surface and subsurface bodies of water as strata movement and deformations propagate from the mined seam through the overburden to the surface (Peng, 2008).Previous research has indicated that mining induced strains are the most damaging to surface streams (Singh, 1992) as well as greatly affecting the integrity of subsurface bodies of water and groundwater flow conditions (Booth, 1986). On the surface, adverse effects to the stream can occur due to the development of either tensile or compressive strain in the stream bed. The development of tensile cracks along the bedrock allows for a potential loss of stream flow through developed fissures. In fact, water flow in the Cataract River of Australia ceased in 1994 as a result of mining-induced strains from longwall operations in the Bulli seam 430 meters (1320 feet) below the river gorge (McNally and Evans, 2007). On the other hand, the development of compressive strains within the rock layers can cause rupturing or buckling of the stream bed, blocking stream flow and/or diverting flow into the fractures at the base (Iannacchione et al, 2010). While these localized fractures can contribute to the loss of stream flows, given time, damaged streams have the ability to self-heal through the regeneration of near-surface aquifers as well as the sealing of mining-induced fractures with rock debris, gravel, sand, clay or other soil particles carried from upstream sources and deposited in the river bed (Waddington and Kay, 2002)."

Jan 1, 2016

By Yuyong Li, Liangman Zhang, Zhaolian Wang, Shun Wang, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements. Adopting 240°-270° larger magnetic element with multi-poles and magnetic pulsation, and combining the devices of multi-channel rinsing water and top flushing water and new style tank, HUATE® JCTN can improve another 2%-10% concentrate mFe% than the traditional MS without lowering the concentrate recovery rate. Thereby, it solves the uneasy concentrate upgradation problem of the traditional MS resulting from the magnetic aggregation. Now, JCTN has been successfully applied in more than 30 mines in Australia, China and Russia, e.g. Sino Iron of CITIC PACIFIC MINING MANAGERMENT PTY LTD. HUATE® JCTN can optimize the industrial processing line by: 1) improving the discarding rate before milling to discard the necessary tailing ASAP; 2) getting in advance the final concentrate after milling. One JCTN can replace many traditional MS in series. In some way, it can also replace the anti-flotation separation process.INTRODUCTIONWe’re writing to introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements."

Jan 1, 2016

By H. Ehnes

"“Industry 4.0” – “Mining 4.0” - perhaps you have already heard of these terms? These keywords signify the next stage of industrial production. The internet and production technologies are growing closer together. Machines can communicate with one another, wherever they may happen to be located. The “Internet of Things” is the appropriate term. But what does SAFETY 7.0 mean? It is both brand new and traditional at the same time. It also has to do with the success of companies, with efficient production. And yet there is a great deal more at stake. It has to do with our lives and our safety – the supreme commodity in this world. What exactly SAFETY 7.0 means, what the number 0 stands for and the meaning of the number 7, and what this all has to do with mining will be explained in the following article. Mining is a fascinating undertaking. Mining is indispensable for a country’s economic development, whatever that may concern: infrastructure, energy supplies or raw materials for industrial production. Mining has brought forth many technological developments and innovations that can currently be found in our daily lives. Mining is impressive, grandiose and repeatedly fascinates mankind with its immense dimensions. Miners throughout the world still work hard and, for this reason, are bound to one another in a special way. In mining, every man looks out for the other; you have to be able to rely on each other. That creates a strong bond. The other side of the coin is that mining and disasters belong to normality in the media and thus also in our perception. Accidents at work and even catastrophes occur in mining, quarries, or raw material operations almost on a daily basis somewhere in the world. They are often associated with extremely serious injuries, or even a fatal outcome, for the miners affected and, in turn, dramatic consequences for the families of those involved. It could be in China, India, Russia, or somewhere in Africa, Asia or America – it mostly does not happen in front of our door or in our neighbour- hood. Perhaps because of this in the daily concert of negative headlines, we do not register these catastrophes any more in our minds. We write them off under the heading “Nothing special”, since there are, day in day out, more terrible news items about wars, civil wars, famines, or ecological disasters. Things only really change if there is a dramatic number of deaths or when we are personally affected, close by in the vicinity, or can witness the rescue action live. In Europe, these three mining disasters in particular have recently generated media resonance:"

Jan 1, 2016

By Mei-Yan Yang, Ltd. Yunnan Yuntong Zinc Co., Yong-Xiang Li, Xing-Zheng Dai, Hong-Liang Wang, Meng-Yang Huang, Peng Zeng, Guo-Feng Li

"The removal of iron asgoethite from the high iron bearing solutions generated in zinc hydrometallurgy using a strong airflow device was investigated. The influence of oxygen flow, copper ion concentration, temperature and reaction time on iron precipitation as goethite was studied. The optimum conditions were: oxygen flow 0.2-0.35m3/h, copper ion concentration 0.25-0.5g/L, temperature 80-90oC, zinc oxide powder neutralizing agent and a reaction time of5to 7hours. Under the optimal conditions, the Fe2+concentration was reduced to 0.025g/L after iron precipitation, and the goethite residue contained 38.7wt.%Fe. The SEM and XRD analyses showed that the iron was present as well formed FeOOH crystals in the iron residue, and the amount of iron sulphate was very low. Production practice shows that, when the average iron concentration in the feed solution was 11.61g/L and 4.08g/L after precipitation, the weight of iron removed was 1,439kg/day. When the average iron concentration in the feed solution was 14.51g/L and 2.73g/L after precipitation, the weight of iron removed was 2,454kg/day. This represents a ~70 percent increase in iron removal.INTRODUCTIONThe objective of iron removal is to produce a small volume of iron residue, and our industrial goethite process meets this requirement. The high Fe(II) solution in our reactor isoxidized/hydrolyzed to precipitate goethite and the precipitate is sent to a pyro metallurgical furnace for final residue treatment. Some literature discusses (DengYong-guiet al., 2008;Meiguang-guiet al., 2001;Zhongzhu-qianet al., 1980) research on iron hydrolysis; one of the reported rate limiting parameters was the low availability of the oxidant when using air and another was the inhomogeneous air distribution. There are two iron hydrolysis-goethite precipitation methods; the Electrolytic Zinc process (EZ) and the Vieille Montagne process (VM) (Lei Xiang, 2006; Xuguo-qiang, 2007;ZhaoYonget al.,2005). The EZ method hydrolyzes the Fe3+directly to FeOOH. The weakness of the EZ process is the low recovery rate of the associated minor metals. The VM method reduces the iron to the ferrous state and then oxidizes the Fe(II)to Fe(III),with simultaneous hydrolysis/precipitation of the Fe(III) as FeOOH. Before iron hydrolysis, the minor metals, such as indium, could be selectively precipitated, because Fe(II)requires a high pH for hydrolysis. So the VM method has a high recovery rate for the minor metals. There levant goethite precipitation reaction is:"

Jan 1, 2016