Search Documents

By Yadong Xue, Fei Wang, Hongwei Huang, Yan Sun

"Increasing attention to subway tunnel maintenance is being paid with the high speed development of urban rail transit system in China. A novel moving tunnel inspection equipment based on machine vision is developed in this paper. High resolution image acquisition system is proposed for tunnel crack and leakage inspection. The main components of this image acquisition system includes high speed CCD cameras, linear lights and high performance computer. To inspect the crack less than 0.3mm with a 3-5km/h speed in subway tunnel, we need to consider resolution and line rate of camera, pixels of cameras, range of inspection and illumination intensity of lights simultaneously. The optimization design is proposed to make the equipment more convenient for tunnel use. Entire tunnel situation can be detected and recorded in a single inspection process. This equipment has already been verified in Shanghai subway tunnel for defects inspection.1. INTRODUCTION In China, the quantity of subway tunnel has reached a large scale in recent years. Until 2014, there had been more than 2300km of subway tunnel in China which accounted for nearly three quarters of Chinese urban railway system (Zhang Chen,2015). In some metropolises like Beijing and Shanghai, most of the metro tunnels has already run over 20 years which within maintenance phase. This has brought about plenty of inspection work and maintenance work to guarantee the tunnel under the serviceability limit states. The increase of running mileage of subway tunnels in China has been displayed in Fig 1."

Jan 1, 2016

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By E. McCullough

"Fostering positive community relations is a principal tenet of sustainable development, but conflict can test even the strongest of relationships. While conflict surrounding resource development projects has the potential to be destructive, it may actually pose opportunities for partnership and collaboration when managed effectively. It is therefore not only important for mineral resource professionals to recognize the financial and social costs associated with legal disputes among project stakeholders, but also for them to prioritize resolving social conflict using alternative channels that allow for win-win outcomes. A variety of dispute prevention and resolution techniques do exist, but successful practice is not yet the norm. Here we review the sources and consequences of social conflict in the context of mining projects, and discuss typical and alternative approaches to conflict management in light of their respective benefits and drawbacks. We also suggest implementation of conflict resolution lessons into resource-related university curricula as a critical step in the continued shift of the mining industry towards sustainable development. INTRODUCTION Social conflict is a recurring phenomenon in the human experience and serves as a critical mechanism for change [1-5]. It occurs when two or more parties perceive that their needs and interests are in direct competition with each other and believe they cannot be reasonably accommodated. Conflict over mineral resource activities, particularly the distribution of benefit and risk, has become an omnipresent issue throughout the world [6-7]. Contrary to common perception, however, conflict can be a positive, transformative encounter in some instances [2, 8-11]. For this to be possible, society and its acting agents must reconsider how to address conflict. What if conflict were only a challenge to try something different? It is well-understood that the mineral industries must manage an increasingly significant volume of social conflict [12-13], which can be a costly externality impacting all of whom are involved. Conflict is commonly considered in a two-party sense, but this can deeply over-simplify the true number of stakeholders. Besides mining companies and community members, government policymakers and regulators, public interest groups, and judicial systems, to name a few, bear the social expenses of poorly-managed conflict [4, 6, 12, 14-22]. It is desirable for interested parties to participate actively in a constructive way to pursue their needs rather than contributing to adversarial relationships, operational problems, and legal costs [1, 4, 12]. Some mining companies are of course already working to develop more productive relationships with their stakeholders, but there is undoubtedly still a gap between ideal and common practices. This gap can inhibit collaboration and threaten the potential for mutually-beneficial resolutions to complex social issues [12]."

Jan 1, 2016

By A. Jordens, Y. Zhiyong

"IMBSRE, one of the largest rare earth element (REE) producers in China, produces a rare earth oxide (REO) concentrate as a by-product by floating the middlings stream from a low intensity magnetic separation step in the main iron ore processing stage. As the mine depth has increased, flowsheet changes in the main iron ore circuit have reduced the REO grade and increased the magnetite to REO ratio in the middling product used as flotation feed for the REO circuit. Extensive laboratory work was carried out and identified a new modified hydroxamic acid product, Florrea 8920, that could provide better metallurgical results over the standard hydroxamic acid used as the main collector. This paper briefly reviews the use of hydroxamates in the flotation of oxide minerals, provides detailed information on the different hydroxamates available from Florrea and then provides a case study of the successful implementation of the Florrea 8920 product in a commercial Chinese REE flotation plant. The case study consists of a one year program of pilot plant testing and industrial trials to confirm the results of laboratory tests. The implementation of the new collector resulted in an improvement in grade and recovery to 61% and 64% respectively. The new collector also provided significant economic and environmental benefits.INTRODUCTIONThe flotation of rare earth element (REE) bearing minerals is a topic which has been dominated in the English language literature by the work conducted on the Mountain Pass bastnäsite deposit (Pradip, 1981; Fuerstenau, Pradip, Khan, & Raghavan, 1982; Pradip & Fuerstenau, 1983, 1985, 2013; Fuerstenau & Pradip, 1991; Fuerstenau, Pradip, & Herrera-Urbina, 1992; Herrera-Urbina, Pradip, & Fuerstenau, 2013). By far the most important collector type used for the flotation of rare earth minerals (REM) is hydroxamates. These reagents were initially extensively described as REM collectors in the English literature by Pradip (1981) however they have been successfully applied to numerous other minerals such as: cassiterite (Sreenivas & Padmanabhan, 2002); pyrochlore (Gibson, Kelebek, Aghamirian, & Yu, 2015); hematite, chrysocolla, rhodonite, hubnerite and pyrolusite (Fuerstenau, 2005); and malachite (Lenormand, Salman, & Yoon, 1979) amongst others."

Jan 1, 2016

By Thomas Camus

"STATE OF THE ART The current situation of ground prediction in TBM is of great concern for tunnelling contractors, and the subject has been quite widely addressed over recent years, for instance by the French Eupalinos 2000 programme, which tested a variety of technological approaches. A number of interesting projects were executed, such as the SOUND and OnSITE projects, part of the German Geotechnologien programme: these projects are focused on seismics, while other techniques such as radar are not considered. Little information and even less industrial applications have been released apart from lab simulations and numerical modelling. A number of field tests in different configurations have been carried out for compression waves, but the results were often not reliable or convincing, and therefore little has been reported in open literature. The advances seem somewhat promising as far as hard rock tunnels are concerned, but ignore the problem raised by concrete lined tunnels such as those bored by a TBM in soft ground. In such tunnels, sending and receiving seismic waves reliably through the lining (and the grouting behind) is quite illusory. A careful analysis of the seismic prediction research results show that the main problem is the source which is poorly controlled and poorly coupled (for instance in concrete lined tunnels, or in approaches that use the TBM cutter head vibrations as a source). Generating waves perpendicular to the tunnel axis is also a problem: aligning with the tunnel axis makes more sense. Radar (Ground Penetrating Radar - GPR) has been used in geotechnical surveys for decades, and also for tunnel inspection. Attempts have been made at using it on a TBM (for example in Japan by Taisei) but mainly using off-the-shelf GPRs, which are not adapted to work in the specific environment of a TBM (because of its huge mass of metal, to start with). Very few results have been published, probably due to the somewhat disappointing performance of such implementations. At present, no TBM has a GPR incorporated in its cutter head that is able to predict ground characteristics while drilling. Another characteristic and drawback of most current methods is that they require dedicated periods of time during which other tunnel construction activities must be stopped. Due to the duration of such operations this leads to performing ground prediction on a weekly basis only, and therefore to a requirement for an investigation range of 100 metres approximately (in order to cover the TBM advance over the coming week). This is not achievable with boreholes made from the TBM, even less if a reasonable accuracy is required, as is usually the case."

Jan 1, 2016

By T. Negeri, M. Boisclair

"A hybrid process consisting of flotation and magnetic separation has been developed to concentrate multi-phase rare earth minerals associated with a carbonatite ore that contains a significant amount of niobium. Fine grinding to a d80 of <65 microns was required to obtain acceptable separation of 92% of the contained total rare earth oxide (TREO) and niobium in half the feed mass. Whereas it was possible to obtain 85% of TREO in 28% of the feed mass through staged cleaning, it was demonstrated that at least 87% and 85% recoveries of TREO and Nb respectively could be achieved in 16% of the feed if the rougher-scavenger concentrates were calcined, quenched, reground to <25 µm and then magnetically upgraded. The paper discusses the overall concept of the flowsheet and the experimental strategies that led to this progress. INTRODUCTIONOut of the approximately 250 minerals known to contain rare earth elements (REEs), only about 60 of them contain REEs in significant amounts. Over 95% of the world’s rare earth oxides (REOs) are believed to occur in the form of three minerals (Pradip & Fuerstenau, 1991) namely bastnaesite (Ce,La,Y)CO3F, monazite (Ce,La,Nd,Th)PO4 and xenotime Y(PO)4. An estimated 51.4% of global REO resources are hosted by carbonatite deposits with the same three minerals as major constituents (Weng et. al., 2015). Any one of the REEs or commonly all of them can be found in these minerals (Ravnaas, 2010). As the demand for critical REEs increases due to the ever increasing applications in advanced technologies, many deposits containing other forms of REE minerals will have to be developed. REE minerals are extensively dispersed and intergrown with several oxides, silicates, carbonates, and phosphate minerals. Consequently it is possible to liberate them only at fine grinding and is thus difficult to separate and produce high grade rare earth mineral concentrates. Most of these minerals contain other important elements such as tantalum (Ta), niobium (Nb), uranium (U), and thorium (Th) in varied quantities. REE minerals in the same ore may exist as carbonates, fluorocarbonates, niobates, silicates, phosphates etc. in association with gangue minerals belonging to different mineralogical groups."

Jan 1, 2016

By Alexandre Passos, Giorgio De Tomi, Tatiane Marin, Dennis Cremonese, Jacopo Seccatore

"In the mining industry, rock excavation is the first phase of the comminution process. Downstreamoperations such as secondary breaking, crushing and milling terminate the process, reducing the size of the grains down to the desired particle distribution. In such a cascade process, every process upstream heavily influences all the downstream operations. When rock excavation is carried out by drilling and blasting, a very economic source of energy (the explosive) is used at the utmost upstream; a more expensive source of energy (electricity) is employed for all the downstream phases. This means that managing the correct employ of the explosive energy is a form of managing the whole process, controlling the operational costs and therefore the profitability of the whole business. We simulated this cascade behavior, using as a starting point the experimental data obtained from small-scale block blasting, evaluating the influence of blasting on the grindability of the blasted material. This study showed the reduction in visible (particle size) and invisible fracturing (micro-cracking, resulting in a reduction of the Work Index WI). The particle size distribution for full-scale blasts was estimated by means of algorithm simulation, then we simulated the behavior of the comminution plant fed with the material possessing the characteristics previously estimated. All the costs (drilling, blasting, electric energy for the engines of the crushers and mill) were calculated and charted. The results show a clear curve that allows to estimate the minimum operating expenditure (OPEX) for the whole mine+plant framework. Being the WI dependent on the output on the blast, one can manage the performance and the expenditure of the whole comminution process by adjusting drilling and blasting parameters For any given mine, it is possible to perform a simulation and encounter the minimum OPEX scenario for the comminution process and managerial choices can be oriented accordingly. In a cascade productive chain as mining is, responsible strategic choices must be taken looking at the entire production framework. Compartmentalized managerial staff and budgets for separated production areas are not acceptable anymore. Somehow higher costs upstream can lead to effective decrease in costs and increase in efficiency and productivity of the processes downstream."

Jan 1, 2016

By Chris Laughton, Bernhard Spoerr

"Tunnel inspections are increasingly needed to ensure that aging infrastructure does not fail in service. To this end the time between inspections is being reduced, the thoroughness of each inspection is being increased to provide for a more detailed assessment of conditions and inventory defects. The conventional Tunnel Report, containing hand-drawn maps and/or photos, and a log describing observed defects and areas of deterioration, is being increasingly replaced by LiDAR generated 3-D surface maps. The data collection process that traditionally supports development of a Tunnel Report is labor-intensive, taking crew-days of engineering effort, and requires partial or full stoppage of tunnel operations. In an urban setting, such multi-day interruptions in service are difficult to countenance for a near-capacity tunnel operation. Under time pressures, the detail and accuracy of the manual inspection process will inevitably be compromised, resulting in a high cost, low quality product. As the tunnel inspection window decreases the argument for incorporating laser scanning in to the inspection process is increased dramatically... The 3D scan technology allows detailed and accurate data to be collected within the tight time frames demanded by the owners and operators of critical infrastructure. Not only does the use of laser scanners improve the 3D accuracy of the data collected, it also, enhances the efficiency and safety of the inspection process, reduces data collection and processing costs and enhances the reliability of results over time. The paper will also demonstrate the value of adding photogrammetric data to the 3D Model to show surface defect discoloration. The accurate and detailed data collected by a combination of LiDAR and photogrammetric techniques provide superior data needed to inform critical asset management decisions related to maintenance, repair and replacement."

Jan 1, 2016

By I. Stanoev, V. S. Stoilov, I. Gradinarov, E. D. Visariev, I. A. Bonchev, Aurubis Bulgaria

"Aurubis is the leading integrated copper group and the world’s largest copper recycler. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper concentrate is thickened and then is filtrated by vacuum disk filter. The thickener overflow is sent to settler for additional clarification. A resent throughput increase resulted in higher solid content in the thickener overflow due to insufficient thickener area. Different scenarios to overcome the issue were evaluated (new thickener, reagents and reconstruction). An increase of the thickening area by installation of lamella modules was chosen as the most promising option. Three lamella modules (1 m3 each) were installed in conventional thickener for the test. Number of sampling campaigns was done to evaluate the effect on solid content in overflow. Parameters of the dewatering cycle were collected during sampling campaign. The products grain size distribution was defined - thickener feed, thickener overflow with and without lamella. The thickener overflow with lamella modules has 2.12 g/L less solid content. The decrease was 71.8%. According to the tests results, the whole conventional thickener was reconstructed with lamella modules. The thickener area was increased by more than 400 m2.INTRODUCTIONIn Copper smelter Aurubis Bulgaria, the copper in slag from the Flash furnace and the Converters is recovered by flotation. The scheme of slag processing is crushing, two stage grinding (autogenous and ball) and flotation. Till 2010 the grinding cycle in the plant was in two stages: the first stage was AG Mill 70×23 working with a classifier and the second stage was ball mill 3.6/5.5 working with a hydrocyclone. In 2010 a new AG Mill 65×78 with hydrocyclone was put in operation in order to increase throughput of the plant. The second stage of the grinding cycle was not changed."

Jan 1, 2016

By Roland Trunk, Marcel Imbach, Yves Boissonnas, Jan Vesely

"INTRODUCTION The expansion of the Suez Canal, which runs between the Mediterranean and Red Sea, is at the top of Egypt’s economic agenda. The £8 billion development plan includes a new channel alongside the existing one which will double the number of ships able to pass each day and several tunnels to connect the Sinai peninsula to the main part of Egypt. The Egyptian government ordered three new tunnels under the Suez Canal in the area of Port Said as part of the Canal Region Development Plan. The three tunnels will contribute to the North Sinai expansion, helping to create a vast industrial zone and completing the coastal road extension from Rafah to Nuewiba. Two of these three tunnels will be allocated for roads and the third for railway traffic. A further part of the Suez Canal development mega project are an additional six tunnels in the area of Ismailia and Suez. The focus of this paper is on the two road tunnels in Port Said and will give an overview of the project and the challenges encountered regarding the technical complexity and tight time schedule both in its design and execution. PROJECT OVERVIEW The tunnels will be built in the area of Port Said (see Figure 1) which is the most northern part of the Suez Canal.The road alignment connects the Port Fuad Road in the east bank of the Suez Canal to the Port Said-Ismailia highway in the west bank with a dual carriageway section. Each of the carriageways has two lanes. The bored diameter of the 2.8 km long road tunnels is 13.050 m and will be driven with two Mix-Shield TBMs. The distance between the two tunnel axes is planned with 42.5 m (discussion about a reduction are ongoing). The width of the Suez Canal is around 340 m at upper level and around 170 m at the bottom. During the TBM drive, three main geological layers are expected. Below a depth of around 40 m in a very soft clay layer, a dense to silty sand layer is predicted. Within the sand layer another silty hard clay is expected in different depths with variable thickness. After finishing the excavation of the road tunnels, the same TBM will be used for the railway tunnel. The lowest points of the road tunnels will be located 59 m below the surface (tunnel invert to surface) and only 18 m of ground cover exists between the tunnel crown and the Suez Canal invert. Minimum ground cover over the tunnel crown is approximately nine meters at the tunnel portals."

Jan 1, 2016

By L. Lorig

"Two types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudo-static analyses. The acceptance criteria are often promulgated by governments despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems than earthquakes. Two types of problem are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare. This paper will discuss the mechanisms for rainfall-induced slope instability, as well as analysis methods. Examples will be discussed and analysis methods are proposed. IntroductionTwo types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudostatic analyses. The acceptance criteria are often promulgated by governments (e.g., Peru, Chile) despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems when compared to earthquakes. Two types of problems are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare, but do exist. In Peru, for example, slopes are required by law to be designed for a 100-year storm."

Jan 1, 2016

By Josh Johnson, Stephen Tadolini, Mark Ferster, Curt Jacobs

"Stillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral. While driving two sub-parallel footwall laterals to about 8,125 m (26,000 ft) long, one of the development drifts experienced a massive fall in a geologically disturbed area created by a dike intrusion. Combinations of a void fill material (Tekseal), polyurethane injection, fore poling coupled with steel arches, and supplemental bolting allow safe and efficient advance through this geologically disturbed zone. This paper presents the details of this project.INTRODUCTIONStillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral.Tunnel Boring Machines (TBMs), shown in Figure 1, have been used extensively at both the Stillwater Mine and the East Boulder Mine to develop access to the J-M Reef. The J-M Reef is a PGMbearing reef deposit located in the Stillwater Complex near NyeMontana. The mining property and location are shown in Figure 2.The Blitz Project is named after the Blitz mining claims and is developing the Eastern extent of the J-M Reef Project., This consists of a 5.5 m (18 ft) diameter TBM drive on the SOE (1,562 m (5,000 ft) above sea level and east of the shaft collar) and a 4.7 x 4.7 m (15 x 15 ft) drill and blast heading on the 5,600E (1,750 m (5,600 ft) above sea level and east of the shaft collar). The Benbow Decline will be completed running perpendicular to the TBM by drilling and blasting methods. The TBM drift will be used for exploration drilling, ventilation, and will serve as the main haulage level. The 56E will be used for ventilation and exploration drilling. The Benbow decline will serve as the exhaust drift."

Jan 1, 2016

By M. Arvola, A. Mäkinen, N. Isomäki

Arsenic is a compound that has no significant market value. However, it needs to be removed from ores, concentrates and other process streams because of environmental or technical processing concerns. A wide range of arsenic containing minerals exists in nature, and in many instances these minerals are also associated with the ones that have commercial value. For example, sulfide copper ores are normally closely associated with minerals like enargite, Cu3AsS4 and tennantite Cu12As4S13. After mineral processing these arsenic sources can report to the waste waters and these effluents need to be treated before discharge or recycling. Ferric arsenate precipitation is a well-established method for stabilizing arsenic in effluents. Electrochemical arsenic removal utilizes the same adsorption/precipitation ideology as ferric arsenate precipitation. Electrochemical arsenic removal, even though it is a simple process in terms of equipment, is a complex system involving chemical and physical mechanisms taking place simultaneously to remove dissolved and/or solid arsenic components from wastewaters. The whole process can be described by the following three steps: 1) electrolytic oxidation at a sacrificial anode (dissolving electrode metal, iron for example), 2) chemical reaction between dissolved iron and arsenic to form a solid precipitate and 3) aggregation of the particles to form flocs, which can be removed by known solid/liquid separation methods. Electrochemical arsenic removal is a very efficient way to remove arsenic from different waters to very low residual concentrations.

Jan 1, 2016

By K. C. Corin, M. S. Manono, J. G. Wiese

Depressants play a crucial role in the flotation of PGM bearing ores as they prevent naturally floatable gangue (NFG) from reporting to the concentrate. This action is regarded as critically important because less dilution of the concentrate means lower costs for downstream processes. However, abnormal water conditions (such as high concentrations of ions) in the flotation system can modify the selectivity of these depressants. It is well known that the existence of selected electrolytes in water can alter the behaviour of some polysaccharide depressants by enhancing their adsorption onto gangue minerals and thereby prevent naturally floatable gangue from moving into the froth phase. Concurrently these same electrolytes may enhance frothability, owing to their stabilising effect on the bubbles within the system. Plant water at various ionic strengths was investigated against depressant type and dosage in order to understand electrolyte-depressant interactive effects during the flotation of a Merensky ore, using entrainment, rate of NFG recovery, and total gangue recovery as proxies. The study showed that the rate of NFG recovery per unit mass of water decreased with increasing ionic strength at all dosages, however the total amount of gangue reporting to the concentrate increased with increasing ionic strength at all depressant dosages. Thus, this paper attempts to consider the effects of both ionic strength and depressant dosage as individual factors within flotation. It further looks to investigate whether any interactive effects exists between these two factors when considered simultaneously.

Jan 1, 2016

By Ngonidzashe Chimwani, David Glasser, Diane Hildebrandt

"Milling circuits play an important role in achieving the desired product; tonnage, size distribution and properties, since they are directly linked to the comminution energy consumption for the whole process. A grinding model with a mathematical simulation was developed for an open milling circuit with a scalped feed from a hydro-cyclone. The circuit was optimized by determining the optimal conditions in terms of energy consumption which would produce a floatable product having a desired size range (i.e. -75 +9 µm) for a platinum-bearing ore. The simulation results showed an operating region comprising the best combination of the ball filling and mill speed to achieve the highest production of a floatable size class, with the minimum energy consumption.INTRODUCTIONBall milling is usually conducted in closed circuits in order to achieve a desired product size without material overgrinding. The technological importance of optimising milling circuits cannot be overemphasised (Toneva and Peukert, 2007). Previous work has brought significant insights into the benefits of modelling milling circuits (Austin et al., 1984; King, 2012; Toneva and Peukert, 2007). However, the ability to model these circuits is dependent on the performance of the classifiers and the fidelity of the grinding mill model used compared to the actual circuit (Toneva and Peukert, 2007). Austin et al. (1984) identified five types of milling circuits as shown in Figure 1 namely; the grinding circuits employing mill in an open circuit, normal closed circuit, reverse closed circuit, open circuit with scalped feed, and, the combined closed circuit. Depending on the presence of the first classifier, the second, or both as well as their corresponding loops (streams), the combined circuit (e) can reduce to; an open (d), a normal closed (b), an open circuit with scalped feed (c) or a reverse closed circuit (a). In the case of an open circuit, the mill is operated without being directly influenced by a classifier. The normal closed circuit does not have the first classifier and therefore the make-up feed is the actual feed stream. Conversely, the reverse closed circuit keeps only the first classifier. The open circuited with scalped feed has only the first classifier but does not have the second one. The overflow stream from the classifier is mixed with the mill product to form the final product for the downstream process."

Jan 1, 2016

"1 INTRODUCTIONThe use of nondestructive testing (NDT) methods to evaluate the integrity of Augered Cast-in-Place (ACIP) and Drilled Displacement (DD) piles has been a subject of significant debate among engineers, contractors and NDT practitioners. This guideline document will illustrate the importance of reviewing all available information in conjunction with the NDT records. ACIP and DD piles have unique properties that must be considered when using a specific NDT method. Any evaluation of the integrity of an ACIP or DD pile must also include a thorough review of the detailed pile installation records and the site specific soil conditions. Long or theoretical descriptions of the methods have not been included in this publication. More detailed information about these NDT methods including their theoretical and historical backgrounds can be found in DFI’s Manual for Non Destructive Testing and Evaluation of Drilled Shafts (2004). Additional information can also be found in the more comprehensive textbook Nondestructive Testing of Deep Foundations by Hertlein and Davis (2006).1.1 PurposeThe intent of this guideline is to provide practical guidance for the proper interpretation of NDT results on ACIP and DD piles. Short descriptions of the main integrity methods available are provided along with several examples of how to use all of the information available to make sound engineering judgments about the results. This publication is a state-of-the-practice guideline to promote accurate engineering evaluations.For engineers inexperienced with NDT, these guidelines provide sufficient background information on NDT methods to help understand the limitations of the testing, assess the results presented to them, and formulate appropriate questions. This is particularly important for engineers charged with the responsibility to determine from those results what, if any, consequences there may be on the performance of the structure under construction."

Jan 1, 2016

"The content of production reports has its origins in raw measurements taken in harsh production environments. The ensuing measurement/estimation errors always affect reproducibility such that, regardless of the fact that they are balanced through statistical data reconciliation, reported numbers are simply the most probable values of inferred probability distributions. This has important implications for how metal recoveries should be monitored and reported. Indeed, in a context where many process optimisation activities are based on small improvements in recovery, there should be no doubt that inadequate handling of measurement/estimation errors can easily exaggerate or mask actual changes in process performance. However, estimates of the reproducibility of reported metal recoveries are rarely reported to plant management. This situation persists despite the fact that a code compliant metal accounting system must inform management about business risks related to metal accounting. To this extent, this paper focuses on the continuous management of reproducibility level of metal recoveries in compliance with the best practices. Sensitivity analysis of primary and secondary metal accounting models is performed to show the resulting probability distributions for metal recoveries. Some guidelines are given for designing and managing metal accounting systems capable of achieving and sustaining predefined levels for the reproducibility of metal recoveries.INTRODUCTIONEach and every mineral processing plant produces daily, weekly and monthly production reports in which metal balances for payable and penalty elements are presented. While such production reports are usually consulted in offices, underlying raw measurements are taken in harsh production environments where mechanical vibrations, humidity, corrosion and dust, to name a few, disturb measurement procedures. It is thus no surprise that several authors (Francois-Bongarcon & Gy, 2002; Gaylard, Randolph, & Wortley, 2014; Holmes, 2010; Spangenberg & Minnitt, 2014) have reported pervasive issues related to mass/sampling measurements in the context of mineral processing."

Jan 1, 2016

By A T. Spathis, M G. Wheatly

Some preliminary dynamic pressure data were obtained from several charges detonated in a tunnel situated in massive granite rock. The context of the work is the potential for desensitisation of explosives, failure of detonators, and sympathetic detonation due to the close proximity of inter-hole and inter-deck explosive charges to each other. Dynamic pressures were measured using piezoelectric gauges in water-filled 45 mm diameter holes adjacent to the charges. Some of the first arrival peak pressures were noisy, and although not fully resolved, may be due to reflections and the physical arrangement of the transducers and their size with respect to the monitoring holes. The estimated peak pressures were between 0.1 to 8.7 MPa at approximate distances of 2.8 to 0.8 m, respectively. Further work is planned with gauges that are disposable, have a higher pressure range, and can be used within a few borehole diameters rather than the piezoelectric gauges used in the present work.

Jan 1, 2016

"Sampling error and bias, especially the Increment Preparation Error (IPE), are introduced when the tool allocated to do the job fails to extract a representative sample. This is the case with chip sampling; the tool can only extract haphazard shapes of loose or fractured material and not always from within the demarcated sample area. Increment Extraction Error (IEE) and Increment Delimitation Error (IDE) could be severe, but are found to be relatively unbiased. The uncontrolled action of the sampler in discarding excess sample material after sample collection has a significant impact on the error and bias introduced with each and every extraction. A new type of bias, referred to as the ‘waste discard bias’, arises when samplers select what portion of the excess sample material to discard at the sample site. Material visually identified as waste is discarded in preference to mineralized broken ore if there is an excess of sample material. This results in a considerable error in the analytical results. The bias is proportional to the reef-waste ratio in the demarcated sample. IntroductionTwo types of ‘sampling’ are distinguished, namely sampling of particulate materials (broken ores) and sampling of solid, unbroken in situ mineralized reef. This study considers only chip- or face-sampling of in situ, goldbearing, carbon-rich conglomerates typical of the Upper Witwatersrand Supergroup and examines where components of sampling error and bias, clearly specified in the Theory of Sampling, may arise during the practice of ‘face sampling’. Many millions of face samples have been extracted from Witwatersrand-type mines using a hammer and chisel, and detailed descriptions (standard operating procedures) of how the samples should be taken have been developed by many mining companies. There is, however, no taxonomy or nomenclature for managing or reporting the different types of errors associated with chip sampling. The Theory of Sampling compiled by Pierre Gy in the early 1950s provides, comprehensive nomenclature of sampling errors that is applied to particulate sampling of ore in a lot, a stockpile, or a moving stream on a conveyor belt. The taxonomy and characteristics of sampling errors, grouped according to the sources from which they arise, and identified by Gy (1973, 1979, 1982, 1992, 1995, and 1998) are shown in Figure 1. This classification of errors is used extensively in regard to the sampling of particulate materials in the mining and minerals industry, but not in regard to chip sampling. A relatively small mass (hundreds of grams) of representative particulate material for estimating the average grade of a much larger mass (thousands of tons – the ‘lot’ in the Theory of Sampling) is extracted by the chipping or cutting of a representative rock ‘sample’ from the stope face."

Jan 1, 2016

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidizing agent. This work shows how the performance of pressure leaching circuits may be improved by optimizing the configuration of autoclaves and the heat removal method. The objective was achieved by creating an autoclave model that combines mass balances, energy balances, and population balances. A base case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity increase options include circuits in which the additional autoclave is added in parallel, in series, and in series with thickening between the two autoclaves. The copper extraction, productivity, and cooling requirements for these options are compared. The series circuit with interstage thickening has the highest extraction and productivity; however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water, and flash recycling. The flash recycle option results in the highest copper extraction, and the quench water option the lowest copper extraction. IntroductionBackgroundCopper sulphide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work.In the pressure leaching process, sulphide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidizing agent, usually oxygen, is required to oxidize sulphide ions to sulphate ions. The oxidation of sulphur to sulphate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2016