Search Documents

By Junhyun Choi, Allan Gomez-Flores, Chonbuk National University, Siyoung Q. Choi, Gahee Kim, Seungkon Kim

In this study, to confirm the effect of depletion attraction on the flotation, we theoretically and experimentally investigate the effect of the depletion attraction force on flotation. While varying the concentration of the depletion agent (polyethylene glycol), three different systems are studied: pure malachite, pure silica, and a 1:1 mass ratio of malachite and silica binary system. We find that recovery increases significantly as the concentration of the depletion agents increases for all three systems, as the depletion agent facilitates the adsorption of the particle on the bubble surface. However, the recovery suddenly decreases in a certain concentration range, which corresponds to the onset of the decreased surface tension when high concentrations of the depletion agent are used. This non-monotonic overall recovery trend implies the surface adsorption of the depletant on a surface. The decreased surface tension of the air/water interface suggests that the recovery rate is lowered due to the adsorption of the depletion agent to the bubble surface, acting as a polymer brush. Based on our observations, we conclude that the depletion force can greatly improve particle adsorption, as predicted in the accompanying theory paper, while simultaneously the adsorption of the depletion agent on the bubble surface plays an important role because it hinders particle adsorption. We also perform experiments in the presence of a small amount of a collector, sodium oleate. An extremely small amount of the collector leads to the increase in the overall recovery, which eventually reaches nearly 100 percent. Nevertheless, the grade worsens as the depletant provides the force to silica particles as well as target malachite particles.

Jan 1, 2016

By Michael Murphy, Khaled M. Mohamed, Berk Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in underground coal mines to reduce rib fall accidents and fatalities. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified.This paper presents a coal rib model to simulate the mechanism of coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff Mine in Australia. Fracturing of the coal rib was defined by critical VALUES (of plastic shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data.INTRODUCTIONCoal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face failure and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities (MSHA, 2015)."

Jan 1, 2016

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By C. J. Hartley

"Scandium oxide can be recovered as a by-product from process streams in a number of chemical and metallurgical plants including TiO2 sulphate pigment, Ni/Co laterite, zirconium oxychloride and uranium operations. The feed materials available for processing can be either mid or end of process streams containing many species in solution. This paper describes the strategies available to limit coextraction of elements into scandium containing streams from TiO2 pigment production and the removal of these elements to deliver high purity scandium oxide.A critical part of process development is to work within the constraints of the main process in terms of introducing new unit processes and producing minimal additional process intermediates and residues. This requires flexibility in designing flowsheets and plants to find novel process routes that avoid production of intermediates and/or the introduction of reagents that can compromise the main process operations.Bloom Energy has developed novel solvent extraction processes for the extraction and refining of scandium oxide that minimise impacts on core process streams within TiO2 pigment plants. The additional unit processes are designed to have minimal contact with pigment plant process streams to produce a concentrate that is refined to nominal 3N purity scandium oxide in a simple, small scale commercial plant."

Jan 1, 2016

By G. Dodbiba, A. Otsuki, T. Fujita, J. Ponou, A. Shibayama

"The different types of nano to submicron particles, which are well-dispersed nano particles, coagulated nano particles or settled submicron particles, have been measured by the interactive force apparatus (IFA). The information is very useful for mineral processing treatment. The IFA can measure the particle size distribution in low to high concentration of particles in liquids and non-light transparent liquids. Here, mainly the emulsion and bubble size measurements are described.Emulsion (w/o type) is prepared with oil and water mixture. The nano to micro emulsion particle size is usually measured by light scattering method. The particle size distribution of emulsion of light oil measured by IFA agreed well with the one by the dynamic light scattering (DLS) method. The water size distribution in emulsions of gasoline is difficult for the small reflection index and C heavy oil is difficult for the black color by DLS method. The IFA can measure both emulsions.There are many methods to measure fine air bubbles, however, the finer nano size measurement apparatuses are DLS method and IFA. A “ghost” peak appeared in the large particle micron meter size in DLS method. The mean diameter in IFA is similar with DLS for the nano meter size. INTRODUCTIONParticle size distribution measurement of nano to submicron particle, emulsion and bubble size distribution are very useful for ultrafine particle separation and characterization of fine particles by the necessity of recent fine minerals separation (For example, Li et al.2016, Mikhlin et al.2016, Wang et al.2013). As for the size measurement of solid particles in liquids, three different types of nano to submicron particles, that are well-dispersed nano particles, coagulated nano particles or settled submicron particles, have been measured by the interactive force apparatus (IFA). The particle size distributions are compared with the one of dried particles measured by TEM or SEM. The well-dispersed nano particle size distribution by IFA is influenced by the nano size surfactant micelles and becomes smaller, when compared with the TEM result. The size distribution of nano size of magnetite particles in water is influenced by the isoelectric point and the mean diameter of coagulation becomes larger. The particle coagulation in diluted suspension is about 2nm smaller when compared with the higher concentration. The submicron nickel particle size distribution is well agreed the result by SEM. The coagulation effect is small in the submicron size of nickel powder in water (Fujita et al., 2013). In this paper, the emulsion and bubble size measurements are mainly described."

Jan 1, 2016

By V. van der Merwe, C. W. Siyasiya

"A petrochemical company experiences premature thermal fatigue failure of the casting moulds used in catalyst production. The aim of the project was to find an alternative alloy that would outperform the current low-alloy cast steel used for the moulds. Based on their thermo-fatigue properties, 3CR12 ferritic stainless steel and H11 tool steel were chosen for testing and comparison with the currently used BS3100 B7 cast steel. Samples of each material were subjected to temperature cycling in a Gleeble 1500TM thermo-mechanical processing simulator, followed by surface analyses. The main parameters derived from the test work were the total true strain, the hot strength of the materials, and the number of cycles to failure. Additionally, the coefficient of thermal expansion for each material was measured using a Bähr dilatometer. H11 tool steel yielded the best performance by way of having the fewest surface cracks, the lowest total true strain per cycle, the most cycles to failure, the highest hot strength, and the lowest coefficient of thermal expansion.IntroductionThe Catalyst Manufacturing Plant (CMP) is a dusty environment with temperatures higher than ambient. Molten mill scale (magnetite, Fe3O4) is tapped from the electric arc furnace into the casting moulds at temperatures close to 1600°C. After 10 seconds the magnetite is quenched with a water spray for 50 seconds to a minimum temperature of 400°C. Sometimes there is residual water in the pans from the cooling fog process (water sprays) in the empty mould. In a typical plant, the factory produces 40–44 batches a day containing between 150–300 moulds, depending on the time required for the specific batch (Buchholz, 2014). The typical batch in the CMP usually weighs about 6 t. The thickness of the tap, speed of the casting belt, and tilting angle all affect the number of moulds per batch.One of the main problems faced during the molten mill scale casting is the premature failure of the casting moulds. Cracks initiate on the surface of the mould, which is in contact with the hot catalyst, and propagate into the interior of the mould. Cracks are generally concentrated in the middle area of the mould where the catalyst makes first contact with the mould, and which experiences the highest temperature fluctuations. This suggests that the cracks are caused by thermal fatigue during the casting process."

Jan 1, 2016

By K. Forsberg, A. Rasmuson, R. Rodriguez Varela, J. Martinez De La Cruz

"This study analyzes the separation of rare earth elements by means of a supported liquid membrane (SLM) with the final objective of recovering REE from an apatite concentrate (Alemrajabi, Forsberg, & Rasmuson, 2015; Mohammadi, Forsberg, Martinez de la Cruz, & Rasmuson, 2015). In this study, the feed phase consists of an aqueous phase containing REE, the membrane phase contains the organic solvent and carrier (D2EHPA and EHEHPA), and the stripping phase is a hydrochloric acid solution. An evaluation of mass fluxes, separation efficiency, and membrane performance is conducted. In order to analyze the suitability of liquid membranes in the extraction of REE, a deeper insight into the mechanisms causing instability is needed. In this study, surface tension is considered as the key factor of Marangoni instabilities and spontaneous emulsification.INTRODUCTIONThe demand of REE and their compounds has increased considerably due to their special physicochemical features that make them crucial elements for numerous high-tech applications, including wind turbines, hybrid cars, mobile phones, and defense technologies. They are also extensively utilized in traditional industries such as nuclear energy, petroleum, metallurgy, agriculture, and textiles (Xie, Zhang, Dreisinger, & Dyole, 2014; Zhang, Wu, Bian, & Zeng, 2014).Solvent extraction is widely used for the separation of REE (Xie et al., 2014; Zhao, Huo, Pan, Li, & Liu, 2014). Di-(2-ethylhexyl)-phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHEHPA) are two of the most effective extractants for the separation of rare earth elements among organophosphorus extractants (Gupta & Krishnamurthy, 2005). However, the difficulty in stripping loaded D2EHPA extractant, especially for heavy REE, has limited its utilization. Yttrium can be stripped at lower acidities in EHEHPA systems compared to D2EHPA systems (Gupta et al., 2005), but the extraction efficiency is lower. Conventional solvent extraction by mixer-settlers is restricted by its large solvent inventory and loading limits, and suffers from phase disengagement, emulsification, loss of solvent, and flooding problems (Swain, Jeong, Lee, & Lee, 2007). In this context, supported liquid membranes (SLMs) present a potential alternative due to their advantages, being low solvent inventory, process simplicity, low energy and operational costs, great enrichment ratio, and combination of extraction and stripping into one single step. A SLM is a system in which two aqueous phases are separated by an organic liquid membrane suspended in the pores of a porous support by capillary forces. One of the aqueous phases is the feed solution with the solute and the other is the stripping or receiving solution. The solute diffuses through the liquid membrane and then is extracted into the stripping solution (Kislik, 2010)."

Jan 1, 2016

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By M. J. Dry, G. B. Harris

"This paper presents basic chemistry and operating conditions for the hydrolysis of ferric chloride into solid hematite and gaseous hydrogen chloride, and shows how this unit operation can be applied in chloride hydrometallurgy to regenerate strong hydrochloric acid and reject iron without also rejecting valuable metals such as nickel, copper and cobalt. Two examples are used to illustrate the hydrolysis technology and compare it to existing technology. The first is the regeneration of spent steel pickling acid, comparing hydrolysis to conventional pyrohydrolysis. The second example is the processing of a hypothetical low grade nickel laterite, comparing the novel chloride hydrolysis route to conventional sulphate HPAL technology.INTRODUCTION Whilst, in many respects, the control and removal of dissolved iron from chloride leach solutions can resemble the manner in which it is done in sulphate systems, chloride chemistry additionally offers the ability to achieve the same objectives in different ways (Harris, 2014). Conventionally, iron is oxidised to its ferric state (if necessary) and then precipitated with a base, usually magnesia where the feed is a laterite and lime where it is a sulphide, since calcium will precipitate sulphate formed during leaching. One method for controlling iron is to form FeOOH, either ß-FeOOH (akaganéite), a-FeOOH (goethite), or a mixture thereof (Fillipou and Choi, 2002). However, if akaganéite is formed, the precipitate will contain a significant chloride component (as high as 7% Cl), leading to chloride losses and difficulty in satisfactorily disposing of the residue. Washing chloride from akaganéite is almost impossible due to the propensity of the solids to undergo peptization. The conventional approach requires the addition of a base, but it is based to some extent on controlled supersaturation precipitation (Demopoulos, 2009), which produces a more uniform and crystalline material and is far more attractive than, for example, the turboaeration process proposed by Great Central Mines in their chloride copper process (Raudsepp & Beattie, 1986)."

Jan 1, 2016

By Ruan Chi, Zhenyue Zhang, Zhengyan He

In order to understand what governs the leaching of exchangeable rare earth (RE) and impurities and enhance the RE leaching process, the effects of the concentration of ammonium sulfate, pH and leaching temperature on the migration of RE and aluminum (Al) during the leaching of weathered crust elution-deposited rare earth ore was studied. The elution curves for ammonium ion (NH4 +) were also studied to reduce the consumption of the leaching agent. It was found that a high concentration of leaching agent can enhance the leaching process of RE and Al, reduce the breakthrough volume of NH4 + and more rapidly obtain the equilibrium of NH4 +. However, excessive leaching agent can both increase the cost and the burden on the environment. There is almost no variation on the elution curves of RE and Al in the pH range of 4-8 and control of the pH of the leaching agent can be omitted. It is better for the leaching work to be done in summer since higher temperatures can enhance the RE leaching process and improve the use ratio of ammonium. Using 0.1 mol/L ammonium sulfate for leaching 250 g RE ore, 95.42% RE extraction can be obtained when the volume of leachate is 102.6 mL. At this moment, only 18.17% of NH4 + is used to exchange RE and 49.22% of NH4 + is left in the leachate that can be reused as leaching agent by replenishing ammonium sulfate. The results of our studies can provide theoretical guidance for high efficiency and low consumption exploitation of RE ores.

Jan 1, 2016

By D. Wines

"Slope stability analyses have traditionally been undertaken in two dimensions assuming plane strain conditions. Although three-dimensional analysis techniques are widely available and used routinely for open pits, two-dimensional analyses are still more common due to the relative ease of model construction and the relatively rapid simulation times.Two-dimensional analyses will often produce different results to three-dimensional analyses for the same slope. It is generally thought that two-dimensional analyses will produce more conservative results. The main reason for the differences is the ability of three-dimensional analyses to account for the three-dimensional nature of the various model inputs, including the slope geometry, the distribution of soil and rock mass domains, the orientation of geological structures with respect to the excavation face, the orientation of the in situ stresses, and the distribution of pore pressure. In some cases, for a long, straight slope in basic geological conditions, two-dimensional analyses can provide a reasonable representation of the problem. However, in many cases, the inability of a two-dimensional analysis to represent the true three-dimensional nature of the problem will lead to unrealistic analysis results.This paper discusses the reasons, as detailed above, for the differences in two-dimensional and three-dimensional analysis results. Work by others is summarized, and additional numerical analyses are performed to provide an improved understanding of the effects of slope geometry, structural orientations, and in situ stresses on predicted stability. Case studies are presented for both stable and unstable slopes, and the behaviour of these slopes is related to the three-dimensional nature of the slope geometry and geology.The previous work, the new analyses performed here, and the case studies show that it is often important to provide a realistic representation of the slope in three dimensions in order to obtain reasonable stability analysis results. This is particularly true for hard rock environments where structurally controlled failure mechanisms are most likely. The paper also highlights the fact that back-analysed properties obtained from one analysis technique are not necessarily applicable to forward analyses using another technique."

Jan 1, 2016

By D. Saramak, T. Gawenda, Z. Naziemiec, A. Saramak

"Crushing and grinding operations are burdensome to the environment due to generating large amounts of dust, noise and waste during course of comminution operations. An indirect negative contribution of industrial crushing processes is an increase of carbon dioxide emissions, which is a byproduct in energy production processes. On the other hand comminution processes in ore enrichment technology are essential due to liberation the useful minerals from the gangue, and producing the demanded particle size fractions of products. The article concerns investigation over negative influence of comminution devices on environment in terms of dust and noise emissions. Several various crushing devices were under investigations, both in laboratory and in industrial scale.The obtained results were analyzed in terms throughput and energy consumption achieved in various crushing devices. The test results allow to conclude that an intensity of dust generation for individual types of crushing devices is varied. An additional aim of this article is to link the aspect of mineral processing with its environmental impact and hence an influence of raw materials beneficiation industry on the quality of life of residents in immediate and close vicinity.INTRODUCTIONMineral raw materials beneficiation processes are an integral part of multi-stage processing of coal, iron ore and non-ferrous metals, production of aggregates, cement, or precious metals and stones. One of the common features of all beneficiation operations is their high energy consumption, which is mainly connected with various operations of feed particle size reduction. Comminution processes in ore enrichment technology are essential to expose and liberate the useful minerals from the gangue, while in aggregate production processes – to obtain the demanded particle size fractions of products. Crushing operations are characterized by a high degree of negative impact to the environment and humans, mainly due to:• High electricity consumption, which indirectly contributes to the increased emissions of carbon dioxide into the atmosphere, since CO2 is often one of the byproducts of energy production;• Relatively rapid wear of device working parts, what forces a production of spare parts and involvement of steel industry;• Intense dust pollution generated during crushing and grinding processes. This is one of the factors affecting the air quality and the consequent deterioration of the living conditions of inhabitants near mines and processing plants; and • Excessive noise emissions."

Jan 1, 2016

By Wengui Su, Qi Zhang, Junce Wang, Zhijun Ma, Xingyuan Weng

"Mesoporous materials with large specific surface area, pore size, and pore volume have been widely used in many fields such as ion exchange, gas separation, adsorption, and catalysis. Mesoporous materials prepared using natural zeolite have the advantages of both acid and alkali resistance. In this work, mesoporous materials were prepared using natural zeolite as the starting material and diethylenetriamine (DETA) as a template. The resulting samples were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD) and N2 adsorption-desorption experiments. The influence of the crystallization temperature and crystallization time on the specific surface area, pore volume, pore size, and morphology of the resulting mesoporous materials are also discussed. Our results show that for an increase in both the crystallization temperature and time, the average pore size first increases then decreases, while the specific surface area first decreases then increases. Based on this work, we concluded that the optimal crystallization temperature was 2003 and the optimal crystallization time was 60 h. These conditions gave an average pore size of 17.93 nm, a pore volume of 0.048 cm3g-1, and a specific surface area of 16.48 m2g-1.INTRODUCTIONMesoporous zeolite, as the name implies, is a highly porous crystalline zeolite. This material is of interest due to its high hydrothermal stability, its adsorption and diffusion properties for macromolecules, and its excellent selectivity and activity as a catalyst. In recent years, it has become a hot spot among research of porous catalytic materials and has been widely used in petroleum and natural gas processing, fine chemical processing, various adsorption and separation tasks, and other uses (Carvalho & Urquieta- Gonzalez, 2015; Teh, Triwahyono, Jalil, Mukti, Aziz, & Shishido, 2015)."

Jan 1, 2016

By Anita Wu

"GENERAL BACKGROUND/CONTEXT The £300 million Bond Street Station Upgrade project will provide essential congestion relief and step-free access to an important interchange and destination station in the heart of the London Underground network. In 2010 London Underground (LU) let a design & build contract to Costain Laing O’Rourke (CoLOR), with the works to be completed in early 2017. CoLOR’s lead designer is Halcrow-Atkins JV (HAT). The station upgrade works comprise the following principal elements: •,A new satellite ticket hall on the North side of Oxford Street •,Two additional escalators and stairs providing congestion relief to the Jubilee line platforms •,Four lift shafts to provide step-free access between the different levels of the station •,Additional stairs to Central line platform level •,Tunnelled connection to the Crossrail station immediately to the south •,Connecting passageways, including ten connections to existing station tunnels. To achieve this, an existing property at 354-358 Oxford Street has been purchased and demolished, and the basement deepened to make provision for the new ticket hall. From this basement two circular shafts have been sunk, providing construction access for the tunnelled passages and lift and escalator shafts. The tunneling is principally in the London Clay stratum, which is widely recognized as a favorable tunneling medium, although the deepest parts of the works extend into the Lambeth Group strata which consist principally of stiff clays at this level but also contain water-bearing sands. The majority of tunneling has been carried out using mechanical excavation and sprayed concrete linings but other techniques have been used in areas where SCL is not practicable.A key challenge for design and construction of the works has been spatial constraint, in particular due to: •,The existing underground station layout •,The Limits of Deviation for the works •,The small construction site at 354-358 Oxford Street •,Overlaying Third Party assets including Listed buildings, sewers and water mains."

Jan 1, 2016

By S. Steinlechner, S. Wegscheider

"In the past, the metallurgical industry was most of the time dedicated on their main commodity, recovering base metals like zinc, copper or lead but leaving other valuable side elements in the generated residues. As a result, these accompanying minor elements, like gold, silver, indium or also PGMs can be found in the dumps of the corresponding industry. Because of political unrest, strikes, economic reasons or decreasing primary resources leading to a high supply risk, also those mentioned minor elements moved into the focus of the recycling industry. Therefore, beside the base metals, first of all the recovery of those minor metals would be of high interest contributing to the economic viability of recycling processes, although they occur in much smaller quantities in materials. In this context, residues from zinc industry, like leaching residues or precipitation residues show high potential to carry silver as well as indium next to lead and zinc. Therefore, the paper summarizes carried out thermochemical calculations investigating a possible recovery of silver as well as indium by volatilization and the influence of zinc and lead on this process. Based on these theoretical investigations with HSC, trials in lab scale were done verifying the obtained results.INTRODUCTIONHuge amounts of iron precipitate, mainly jarosite get landfilled every year although there is a high content of valuable metals in this residue beside iron. Nevertheless, jarosite has to be dumped due to the presence of contaminating heavy metals. The accumulation of these residues takes up massive land on the one hand but also causes a series of environmental problems in ecosystems on the other. Moreover, some toxic ingredients such as arsenic and cadmium can be dissolved in rain water and are therefore harmful to the health of the aquatic systems. (Erdem & Özverdi, 2011; ÖzverdI & Erdem, 2010) Approximately 0.5 t of dry jarosite accumulate in the production of 1 t of zinc by the hydrometallurgical zinc-winning route (Svens, 2010). Jarosite is a precipitation residue formed during the iron removal. In general, the iron already exists in the zinc ore which is why zinc ferrite builds up during the roasting step of the zinc ore. Zinc ferrite is only soluble in strongly acidic solutions and during the hot acid leaching step it gets dissolved while zinc and iron enter the solution. It is necessary to get rid of the iron because otherwise it would deposit on the cathode first due to its precious character which would be harmful in the zinc-winning electrolysis. Nevertheless successful investigations were done by adding chlorine to the jarosite to recover silver. These findings leads to another residue which occurs in huge amounts – electric arc furnace dust (abbreviated with EAFD) from the iron and steel industry. In 2013 the annual electric steel production reached about 451 million tons. Around 15-20 kg of EAFD is produced per ton of steel in an electric arc furnace (EAF), creating approximately up to 9 million tons of dust per year. (Grabda, Oleszek, Shibata, & Nakamura, 2014; World Steel Association) Next to elements like zinc, lead and iron, chlorine and fluorine are present in this dust. While galvanized steel plates in the scrap act as a source for zinc, casting powders, flame retardants and synthetic coatings are responsible for the chlorine and fluorine contents in the dust."

Jan 1, 2016

By L. Alagha, M. Khodakarami

"This work focuses on the extraction of rare earth metals (REE) from aqueous solutions using stimuli-responsive polymers. Various parameters affecting the adsorption capacity of the polymer, including pH, polymer concentration and REE concentration were studied. The interfacial behavior of REE in aqueous phase before and after polymer addition and the mechanism of the formation of metal-polymer complexes and their properties were investigated using UV/VIS spectroscopy. Results obtained would help to test the feasibility of employing stimuli responsive polymers in pre-concentration of rare earth elements associated with other elements in mineral aqueous streams prior to solvent extraction. The pre-concentration step would reduce the amount of organic solvents used for extraction and striping compared to conventional extraction processes. INTRODUCTION Rare earth elements (REEs) have become the foundation for several technologies and have been used extensively in many industries such as modern electronics, green energy, health care and transportation and defense [1-4]. As these industry sectors are growing, the global consumption of REEs is going to increase dramatically. The current global REEs demand is estimated to be 105,000 tons of rare earth oxides per annum with an expected annual growth of 5.6% [5-6]. Rare earth elements are produced from different sources (primary and secondary). China is considered as the largest producer of REE in the world, providing about 90% of the world’s mine production while the United States is second with 4% of the mine production [7]. High global demand for rare earth materials results in shortage of such materials in the near future. It should be considered that the term ‘‘rare’’ earth is not an accurate term, since they are abundant in some extent in the Earth’s crust, but are typically finely dispersed. Thus, nowadays looking for more efficient and cheaper methods for extraction, separation and purification of low concentrated REE ores and exploring secondary sources are essential. Rare earth materials are found in raw condition and require treatment that involves several processes, which can consume money and time. Recent improvements in extraction and recycling technology have made the extraction of rare earth elements from rare earth sources more feasible in terms of cost and time [8-10]. Physical and pyrometallurgical methods require high-energy and thus high costs. Moreover, due to environmental problems, environmental protection systems are required, and they are not as adaptable as chemical processes [11, 12]."

Jan 1, 2016

By H. Jung, J. Kim, Y. Lee, Y. Seo

"Shale gas has become an increasingly important source of natural gas supply in North America and around the world. Horizontal drilling and multi-stage hydraulic fracturing are the two key enabling technologies for the economic development of these shale gas reservoirs. It is believed that gas in shale reservoirs is mainly composed of free gas within fractures and pores and adsorbed gas in organic matter (kerogen). It is generally assumed in the literature that the monolayer Langmuir isotherm describes gas adsorption behavior in shale gas reservoirs. In this work, we have analyzed several experimental measurements of methane adsorption from the Horn River Shale core samples that obey the Langmuir isotherm. INTRODUCTION In nature, gas shales are characterized by extremely small grain size, extremely low permeability on the order of nano-Darcy (10-6 md), small porosity, and high total organic carbon (TOC). Shale can serve as both source and reservoir rock. The amount of gas in place in shale is strongly affected by the TOC, clays, and the adsorption ability of methane on the internal surface of solid (Martin et al., 2010). Since a considerable amount of gas in shale reservoirs is adsorbed, investigation of gas adsorption can provide critical insights into evaluation of well performance and reservoir characterization. Generally, natural gas in shale reservoirs is stored as free gas in both larger mineral pores and natural fractures, as well as adsorbed gas within organic matter (Leahy-Dios et al., 2011). EXPERIMENT METHOD & THEORY Adsorption Experiment Several experiments were carried out on 9 shale core samples obtained in a vertical well drilled within Horn River basin (Figure 1). The CH4 adsorption isotherms were measured for the different depth. In order to measure the amount of adsorbed gas, the high pressure Belsorp-HP equipment applying volumetric method was used. The temperature was kept at 298 K and pressure was increased up to 18 MPa. Approximately 5 g of crushed sample was used for each measurement."

Jan 1, 2016

By E. Ghali, C. Su, G. Houlachi

"The influence of lead ions on zinc electrowinning process was investigated by means of electrochemical noise measurements (ENMs) and cyclic voltammetry in conjunction with scanning electron microscopy and X-ray diffraction. All electrochemical experiments were performed in sulphuric acid electrolyte containing different lead ion concentrations as impurity. Lead was added in six trace levels between 0.05–0.8 mg/L in the bath. The lead content of the zinc deposits was dependent on the introduced lead concentrations. The overpotential associated with zinc electrodeposition shifted to higher values with the increase of lead concentration in the solution. An appropriate correlation was found between the different concentrations of lead in the electrolyte and the morphology of zinc deposit by ENM. The results showed that the increase of lead ion concentrations is generally accompanied with the decrease of skew and increase of kurtosis values that could be related to the morphology of zinc deposit. Effectively, the morphology changes from well-defined hexagonal platelets to large hexagonal, layered platelets and finally to non-symmetric refined crystalline structure, respectively.INTRODUCTION In commercial zinc electrowinning, zinc oxide is leached from the roasted calcine with an aqueous acid sulfate electrolyte. Then the zinc-rich solution is purified and transferred into an electrolytic cell. During electrolysis, zinc is deposited on aluminum cathode where lead-silver or pure lead is served as anode. Electrodeposition of zinc could be influenced by several parameters such as bath acidity, temperature, current density, the nature and concentration of impurities as well as additives in electrolyte. Metallic impurities play a complex role during zinc electrowinning and they can adversely"

Jan 1, 2016

By Eckl, Martin, Stefan Lemke, Martin Londschien

"Tunnels are built with a design life expectancy of over 100 years. One key component of such a design is the waterproofing system, which must reliably fulfil its function during the whole service lifetime of the tunnel structure. This paper deals with the determination of test criteria for the durability assessment of geosynthetic products in tunnel sealing systems. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa. To verify the results of the new test procedure the material properties of geosynthetic products samples removed from older tunnels are investigated. Based on the presented results of the still ongoing research programs some preliminary conclusion regarding the updating of regulations for tunnel sealing systems are given. INTRODUCTION Watertightness is directly related to the durability and serviceability of the concrete lining. Therefore, modern traffic tunnels and shafts (Figure 1) are generally protected against mountain/ground water and water penetrating through rock fissures by a sealing system, for example with a loose-laid polymeric sheet membrane. Hereby the waterproofing sealing systems must be reliably fulfilling their function during the whole service life of the tunnel structure, regularly of more than 100 years. In consequence, the quality and lifetime performance of the waterproofing materials—beside the correct professional and careful installation in a tunnel infrastructure, is of great importance. The challenge for the industry, owners, operators and designers is ultimately the development of qualification testing and requirements (acceptance criteria) for products to ensure the design lifetime performance. Hereby the qualification procedure is seen as a routine integrated in standards, norms or guidelines, wherein test procedures should cover typical environments for the specific application fields. Polymeric synthetic raw materials are increasingly used in products with long service lifetimes (e.g. in injections, gaskets, waterbars, spray-applied and sheet waterproofing membranes). During service they are subjected to chemical (e.g. oxidation processes) and physical (e.g. changes in morphology) influences from the environment, which affect their mechanical properties—and they age. Hereby organic materials are more affected than inorganic materials. Also, polymers show strongly temperature-dependent properties compared with other construction materials. However, their long-term aging behavior is not given per se and has to be explored extensively by suitable tests, which simulate—under accelerated processes—real exposures and loads. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa."

Jan 1, 2016

By Joe Silvestri, James Carroll, Steve Rondinelli, Raelene Shelly, Jason Miller

"The I-70 Eisenhower-Johnson Memorial Tunnel (EJMT) Fixed Fire Suppression System (FFSS) will help protect the traveling public as well as the entire tunnel itself, which is a critical asset of the Colorado highway system. This project is part of an effort to avoid any closure or long-term damage to these tunnels after a fire event. Historically, the EJMT complex has experienced two to three fires a year. While CDOT has firefighting capability at the EJMT complex, the fixed fire suppression system will provide first responders the critical time needed to safely approach the scene and take action, and is a necessary tool in combating tunnel fires, keeping the public safe, protecting the tunnel structure, and minimizing disruptions to traffic. This paper provides a case history of the first-of-a-kind design and construction of the EJMT FFSS. Major project elements include; water-only deluge fire suppression system, fiber optic linear heat detection system, updated fire alarm system and new drainage system. PROJECT BACKGROUND The I-70 EJMT FFSS was awarded to the Design Build Team lead by Barnard Construction, supported by Rondinelli Life Safety, BCER Engineering, ILF Consulting, Western States Fire Protection and Systems Group. The team conducted successful live fire tests at the Boulder Regional Fire Training Facility in November 2014, with the final design of the FFSS and other supporting infrastructure completed in the spring of 2015. Construction began in early summer of 2015 and the project was completed in December 2015. While CDOT currently has firefighting capability at the EJMT complex, this project features an intelligent linear heat detection system that can accurately identify a fire within feet of its location and subsequently activate the corresponding water-only FFSS deluge zone, bringing water in from an existing supply system on the west side of Loveland Pass. The detection system also activates cameras so the EJMT onsite control room personnel can view and better assess a fire event. The uniqueness of this design is that the majority of the installation occurred above the traffic lanes in the tunnel, which resulted in minimal impacts to motorists below. The fire suppression system will help protect the traveling public as well as the tunnel structure, a critical asset to the highway system. This project is intended to reduce damage and avoid long-term closures of the tunnel due to fires. A long-term closure could cost Colorado billions of dollars and negatively impact tourism along the I-70 mountain corridor."

Jan 1, 2016