Search Documents

By E. S. Peters, M. J. van Rensburg, M. Le Roux, Q. P. Campbell

"The demand for energy has continued to rise worldwide in line with population growth. The majority of South Africa’s electricity is supplied by coal-fired power stations. The amount of fine coal (-2 mm) generated at coal processing plants has increased, due mainly to mechanized mining methods. Fine coal retains more water, which lowers its heating value.Drying the coal is costly and it is difficult to achieve the required moisture content. Consequently, coal fines are often discarded. An estimated 8% of the total energy value of mined coal is lost1.Fluidized bed technology is often used to dry coal thermally, but this method is expensive and has an adverse environmental impact. The objective of this study was to investigate the removal of moisture from fine coal (<2 mm) in a fluidized bed operated with dry fluidizing air at moderate temperatures as the drying agent. The effects of different air temperatures and relative humidity levels were investigated in a controlled environment. The study further investigated the influence of coal particle size on moisture removal.The drying rate was found to increase with increasing temperature. The relative humidity of the drying air had a more pronounced effect on the drying rate, even at temperatures as low as 25°C.. It became more challenging to remove moisture as the particle size decreased. The gain in calorific value was greater than the energy required to dry the coal samples, showing that a fluidized bed using moderately warm dry air is an energy-efficient drying technology. The energy efficiency of the fluidized bed compared favourably with other thermal drying methods.Paper written on project work carried out in partial fulfilment of Degree in Chemical Engineering(NWU) - Pursuing Masters in Coal Beneficiation"

Jan 1, 2015

By A. M. King, J. M. Neilsen

"Roughness at varying scales is an important component of the shear strength of discontinuities. Small scale roughness can be assessed in drillcore and through laboratory testing of drillcore derived samples. Large scale roughness, or waviness, also plays an important part in peak shear strength and a number of methods for its incorporation into defect plane strength models are presented.A number of methods for capturing waviness data from exposed faces are reviewed. A method is presented for deriving waviness from downhole televiewer data, which is shown to be significantly more accurate than structural data derived from core logging. The method is based on work undertaken in the highly anisotropic bedded units of the Hamersley Province, Western Australia where televiewer surveys are routinely undertaken. Values of waviness are derived through a review of variation in dip resolved in the direction of the slope face. This method allows design engineers to incorporate large scale roughness in defect plane shear strengths at the design stage.INTRODUCTIONThere are a number of constitutive models currently being applied by rock mechanics practitioners in calculating defect plane shear strength parameters, such as Patton, Barton – Bandis and Hencher [1, 2, 3]. Most of these shear strength determinations are typically undertaken by determining the base or residual friction angle, and applying corrections for small and large scale surface roughness."

Jan 1, 2015

By S. T. Camagu, J. Dutta Majumdar, S. L. Pityana

Laser surface alloying was used to develop copper and molybdenum aluminides by injecting premixed copper and molybdenum powder particles into a laser-generated melt pool on an aluminium substrate. Different laser processing parameters were used to produce the composite thin layers on the substrate material. The microstructure and phase constituents of the composite layer were studied by means of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) techniques. Experimental results show that the matrix structure of the metal matrix composite layer consists of ?-CuAl2and MoAl5. Surface hardness was increased by a factor of 3.

Jan 1, 2015

By N. T. Oo, L. D. Hutton

"The Banora Point Upgrade Project is a 2.5km long six-lane divided freeway in northern New South Wales, Australia. The geology at the project area comprises a volcanic succession of variably weathered basalt flows and agglomerate deposits that reach 48m in thickness and overlie Mesozoic sedimentary rocks. A site specific rock classification system was developed that characterised all the rock units based on the engineering properties governing the rock mass behaviour i.e. intact rock strength and defect characteristics (spacing, aperture, infilling, wall roughness and weathering) irrespective of the geological origin. This approach simplified the design and the on-site verification processes. Based on this classification system, rigorous quantitative statistical assessments of the available geological information including various laboratory and field testing were performed to derive the geotechnical design parameters for various rock classes. These parameters were used to complete geotechnical designs of retaining wall systems. INTRODUCTIONThe Banora Point Upgrade Project is a 2.5km long six-lane divided freeway in northern New South Wales, Australia. The key features include two interchanges, a 300m long viaduct, a large cutting through Sexton Hill with an associated 100m wide Land Bridge and retaining walls reaching 490m long and up to 22m high. This paper focuses on the derivation of representative geotechnical parameters for geotechnical design of the retaining structures supporting Sexton Hill Cutting including bored pile retaining walls and soil nail walls. The geology at the project area comprises a volcanic succession of variably weathered basalt flows and agglomerate deposits that reach 48m in thickness and overlie Mesozoic sedimentary rocks. Due to the complex geological nature of the site, an understanding of the regional and local geology, the typical behaviour of individual geological units and the implication of onsite variations from design intention are the ultimate challenges to the geotechnical engineer in order to select representative geotechnical parameters for design."

Jan 1, 2015

By M. Pötsch, A. Kluckner, P. Söllner, W. Schubert

"The in situ block size is a key parameter in the geomechanical characterization of rock masses. It describes the fracturing of the rock mass and thus is a measure for the degradation of the rock mass strength. Several classification systems use the in situ block size. For instance, the Geological Strength Index (GSI) requires the “blockiness” and joint surface condition factor as key input parameters. The “blockiness” has recently been related to the in situ block volume (Cai et al., 2004). Due to the limited information about the internals of a rock mass, it is not possible to determine the in situ block size directly. Currently, the in situ block size is determined by calculations using oversimplified models, vague estimations or, due to the lack of relevant information, it is neglected. As remote measurement systems have become available for rock mass characterization, a more comprehensive record of discontinuities can take place. Measurements can be performed on exposed rock outcrops and in particular on tunnel faces and walls, delivering the location, orientation, spacing and persistence of discontinuities at an arbitrary number and locations. An estimation of the in situ block size at the same level of sophistication is still not available. This paper aims at examining the relationship between visible and measureable information at the rock surface, and the in situ block size. Three-dimensional block model simulations were performed using the block model engine of the distinct element code 3DEC. Initial investigations focussed on the minimally required observation area in order to obtain reliable block size distributions. Based on a representative volume element, a reference distribution of the block area at the observation area for a specific discontinuity system was determined. Subsequently, the size of the observation area was decreased stepwise and each new distribution was compared to the reference distribution. For all analyzed systems, it turned out that the mean block area must be smaller than 1% of the observation area to achieve a reliable block size distribution. Further simulations focussed on discontinuity systems with three non-persistent sets. The results were compared to the formula proposed by Cai et al. (2004). A transformation factor T was introduced which replaces the persistence terms in Cai et al.’s proposed formula. The factor describes the correlation between block volumes generated by persistent and corresponding non-persistent discontinuity sets. The simulations included the variation of the discontinuity set spacing, persistence, and orientation. The mean and additionally the 25%-, 50%- and 75%-quantiles of the block size distribution were analyzed. Examining all values for the transformation factor the distribution can be described by a power function with a negative exponent. The function depends on the persistence only. Finally, the results of random simulations were compared to the analytical formula using the transformation factor. The predicted mean and selected quantiles show a good agreement with the simulation results. It gives a comprehensive picture about the block size distribution in discontinuity systems with three non-persistent sets."

Jan 1, 2015

By Henri Fredriksson, Rami Saario, Mark Weatherseed, Juri Matinheikki

"The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value. With regard to solvent extraction, the introduction of an innovative modular plant design will help to address these issues. The first such modular offering is Outotec’s VSF®X modular solvent-extraction plant that uses prefabricated and transportable modules. Reuse and recyclability have underpinned the design concept. The greatest advantage of the VSF®X modular solvent-extraction plant is its relocation possibility. Additionally, it is suitable for various metals and plant capacity is adjustable through a scalable modular structure. After a dedicated plant lifecycle, the plant can be dismantled and relocated to a new site. This reuse ability offers major benefits for short-term plants, making them more feasible due to higher residual value. A net present value analysis is made for two examples, a conventional plant with no relocation possibility and a modular movable plant with extended plant life cycle, in order to evaluate the feasibility of modular plants. Results indicate that modular plant design could offer an economical solution with the additional advantage of improved overall sustainability through its life cycle. INTRODUCTION The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value (NPV) (Mudd, 2010; Norgate & Jahanshahi, 2010) . Awareness of sustainability issues is also rising and sustainability reporting is now a key element of many companies’ public and investor relations. Major companies are now putting more effort in this area to earn legitimacy for new projects (Mudd 2010)."

Jan 1, 2015

By M. O. Pekguleryuz, D. S. Aydin

The high temperature oxidation and ignition resistance of Mg-(0-6) wt% Nd alloys have been investigated via isothermal and continuous heating experiments conducted in air atmosphere. Alloy composition is observed to be effective in low levels (~ 0.5 %) in the ignition temperature (Ti) of the alloys; the Ti of pure Mg increased from 630 °C to 770 °C with 0.5 wt% Nd addition. However, no noteworthy improvement was achieved with further additions up to 6 wt% Nd. The initial microstructure was observed to determine the oxide structure on the surface due to the differing oxidation behavior of the phases (a-Mg + Mg12Nd intermetallics). It has been found that the formation of a Nd-depleted region at the subsurface due to extensive Nd oxidation at the oxide/intermetallic interface lowers the protective ability of the oxide scale.

Jan 1, 2015

By Michael Arnold

"BAUER Foundation Corp. was one of three contractors awarded with the installation of a cut-off wall at the Herbert Hoover Dike Rehabilitation project. The cut-off wall was constructed up to 84 feet deep and 25 inches thick. It extended from the crest through the middle of the existing dike into the underlying peat, sand, and rock layers. BAUER used the cement deep soil mixing method of Cutter Soil Mixing (CSM) to install the wall. Soil mixing was facilitated by first removing the peat layer in the wall alignment using Kelly drilling and replacing it with suitable backfill, resulting in a secant pile wall arrangement of replacement columns. BAUER successfully finished four task orders with a total length of just over 10 miles. Up to six rigs of the types BAUER BG 28, BAUER BG 40 and RTG RG 25 were concurrently used to perform the replacement columns and the cut-off wall installation.The paper introduces the project, the geotechnical site conditions, and the requirements specified by USACE. It focuses on the specific adaptation of the CSM method to the site conditions and on the equipment used. Strength and permeability results obtained from an extensive testing program are presented. The impact of the curing conditions on lab and in-situ test results is studied, and test results are related to soil conditions.PROJECTThe Herbert Hoover Dike is a 143-mile-long dike encircling Lake Okeechobee in south central Florida. When it was constructed in the 1930s and 1960s, the purpose of Herbert Hoover Dike was flood protection from hurricanes. However, during the 1970s a higher lake level was maintained permanently to provide local agriculture with water. Later, damage became apparent during two nearly back-to-back high water events in the 1990s, when numerous sink holes, seeps, pipes, and boils were observed (Fig. 1). In 2000, the Congress approved USACE to propose rehabilitation measures. The installation of a cut-off wall into the existing dike was chosen during the initial design process as the preferred measure to improve the safety of the dike (Davis et al. 2009).The first section of the dike to be rehabilitated was Reach 1 located along the southeast side of the lake between the towns of Port Mayaca and Belle Glade. An indefinite delivery indefinite quantity (IDIQ) multiple award task order contract (MATOC) was issued for this 22.4-mile-long stretch by USACE in 2007. BAUER Foundation Corp. (BAUER) was one of the three contractors that succeeded in the qualification process. Each of the three successful contractors had their own novel construction techniques. In the years 2008 to 2012 BAUER executed four task orders totaling over 10.0 lineal miles of cut-off wall with 3.3 million square feet of design surface area."

Jan 1, 2015

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont USA (Newmont) in Nevada was faced with such a need in their Carbon-in-Leach (CIL) train. In a collaborative effort between Newmont and Derrick Corporation, tests were conceived to assess the viability of drop in replacement screen using a three dimensional screen panel. The urethane pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade their urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing, and other scalping applications.INTRODUCTION In Spring of 2014, Process Machinery Associates (PMA), Derrick Corporation’s (Derrick) local area representative, met with Newmont USA (Newmont) to discuss the operation of the in tank screens in the carbon in leach (CIL) train at Twin Creeks, near Golconda, Nevada. The process was originally designed for 13,000 +tons per day (tpd) but has been steadily rising since the plant was commissioned and now Newmont requires 16,000 tpd to be processed. The original screens were running at their maximum capacity and Newmont required additional screening capacity to continue the upward trend in production. Physical separation by use of screening is one of mineral processing oldest methods. Screening media can be prone to blinding and pegging and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and therefore larger machines, screening media that doesn’t blind, or a combination of both. In an effort to avoid larger machines, Derrick Corporation had been working on a revolutionary three dimensional panel which would add non blinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 (Carlin, Nevada) in July of 2013 and was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By Jie Li, Xinyu Liu, Yan Chen, Linjian Ma, Yasong Wang

Nonlinear time-dependent response analysis of salt cavern under extreme loads in disaster mode is of great importance to the safety and disaster prevention of gas storage group. Uncontrolled blowout is one of the extreme conditions for compressed-air cavern operation. Based on the geological structure of Jintan salt deposit, China, the numerical model of the complete process of water solution, cyclic operation, and internal pressure runaway was developed. The effects of rapid unloading on the stress filed, the progressive failure of surrounding rock, the volume convergence of storage cavern, and the ground subsidence were simulated employing an elasto-viscoplastic damage constitutive equation for rock salt. The results indicate that the damage and failure zones propagate much larger in the mudstone interlayer than in the host salt. The volume of damage and failure zones surrounding salt cavern induced by unloading process is 5~6 times that of cyclic injection and withdrawal process. The average volume convergence rate of salt cavern reaches 0.012%/d~0.013%/d, which is 6~6.5 times that induced by cyclic operation. The ground subsidence exhibits a typical funnel curve. The affected region of ground subsidence due to rapid unloading in the blowout period is about two times the maximum cavern diameters. Furthermore, double cavern analysis reveals that the interaction between adjacent caverns may be ignored so long as the pillar width is larger than two times the maximum cavern diameters.

Jan 1, 2015

By J. J. Taute, N. B. du Preez

"A well-performing solvent-extraction circuit is a key part of producing good quality copper cathode. To ensure consistent operation, a good understanding of the circuit’s operation and an ability to rapidly troubleshoot key parameters is required. This paper briefly discusses the modeling of solventextraction circuits. The paper then goes on to discuss the determination of key performance parameters from plant data and comparing these with the circuit models to quantify circuit performance. The identification and troubleshooting of circuit issues is presented with a worked example. INTRODUCTIONA well-performing solvent-extraction (SX) circuit is a key part of producing good quality copper cathode. To ensure a consistent, high-quality operation, a good understanding of the circuit performance is required. Evaluating the performance of an SX circuit is an extensive topic. The objective of this paper is to focus on the evaluation that the metallurgist should be performing on a regular basis using flow and concentration data. This paper does not cover important topics, such as crud management, phase continuity, or organic management. Some basic SX modeling concepts are first be presented. The calculation of the parameters is then presented with a brief discussion and recommended ranges (where applicable). A worked example is used to provide a basis for further discussion on the evaluation of the calculated parameters and use of data collected.BASIC SOLVENT-EXTRACTION MODELING CONCEPTSThis section presents the basic modeling concepts used in SX simulation packages currently available. SX reagent suppliers have invested significant time and effort into collecting data on the performance of their reagents under different conditions. Based on these data, suppliers have developed packages which they normally make available to their clients for free. These are typically used for process design and plant optimization studies. For example, BASF developed ISOCALCTM and CYTEC Industries developed MINCHEM® and MEUMTM.Chemistry of Copper Solvent ExtractionLiquid–liquid extraction involves the selective transfer of a substance between two immiscible liquid phases by controlling the relative solubility in each phase. In the case of copper SX, the exchange is typically achieved by an oxime-based chelating mechanism. In particular, mixtures of aldoxime and ketoxime are normally used in conjunction with modifiers. More detail on this extensive topic can be found in Schlesinger et al. (2011)."

Jan 1, 2015

By Henrik Saxén, Mikko Helle, Hamid Ghanbari

In this study, a process integration approach in a primary steelmaking is investigated to evaluate future operation concepts of a steelmaking site considering sustainability issues. Mathematical programming is used to study the integration of the steel plant with chemical units for utilization of available off-gases in the system, and carbon capturing and sequestration unit. Different industrial carbon utilization options are considered to find the best route of development. A multi-period optimization model is developed based on site-wide mass and energy balances by considering the availability of the fuels and by-product gases and their consumption in the production system and a conceptual polygeneration system. The objective is to reach maximum economic profit while environmental aspects of integrated system are considered for different fuel systems, alternative blast furnace reductants and implementation of new process technologies. The model can provide useful information concerning techno-environmental and economic aspects for decision-making and can estimate optimal operational condition of current and future primary steelmaking under alternative scenarios. The results of the work illustrate the potential to develop steelmaking towards more sustainable operation in the future.

Jan 1, 2015

By Paul Worsey, Gillian Worsey

The basic blasting class at Missouri S&T blast in the quarry at the experimental mine in preparation for the International Intercollegiate Mining (Mucking) Competition in April 2014.

Jan 1, 2015

By A. Blackmore, D. Baker, L. Human

"Mechanical mixing equipment is common in a wide variety of mining, metals and process applications, such as hydrometallurgical reactors, solvent extraction, digestors, and tanks for storage of slurry or hydrocarbons. Computational Fluid Dynamics (CFD) has been applied successfully to single-phase mechanical mixing problems for several decades and is established as a reliable design tool. As computational power and CFD codes have improved over the years, there have been significant advances in modelling capabilities including improved models of turbulence, interaction of rotating and stationary components, multiphase flows, and modelling of free surface interfaces, for example. This paper will provide an overview of the application of CFD to mechanical mixing problems. First, it will review the traditional single phase Multiple Reference Frame (MRF) approach and introduce a range of advanced modelling techniques. Three examples of the application of CFD to industrial mixing problems will be given. It will be demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause of mixing problems, and testing modifications to existing operations."

Jan 1, 2015

By H. P. Kritzinger, T. C. Kingsle

"Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications, including ferrovanadium, nickel carbonate, nickel laterite, iron ore reduction, and spodumene (lithium) production.This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates."

Jan 1, 2015

By Gabriel Böde Jimenez Leon, Michael Karmis, Christopher Newman, Zach Agioutantis

"When utilizing high recovery underground mining methods, such as longwall or high-extraction room-and-pillar mining, the movement and deformation of the overburden propagate toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidenceinduced changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, the resulting strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed ruptures, upward, blocking stream flow or having the stream diverted into the fracture zone at the base (Iannacchione, et. al., 2010).Recent investigations on the effects of underground mining on surface bodies of water suggest that to determine the degree of stream impact one must also consider the geologic structure and thicknesses, surface topography, watershed drainage areas, width of river bed and rate of mining. Due to the complex nature and number of parameters affecting surface streams, subsidence modeling tools and software packages should be implemented throughout all stages of subsidence planning, prediction and control. The Surface Deformation Prediction System (SDPS) utilizes the influence function for the calculation of final subsidence deformations with respect to the angle of influence, supercritical subsidence factor as a function of the percent hard rock, edge effect offset distance, and surface topography. Developed more than 25 years ago, SDPS has been continually updated with new analysis and prediction features, providing a reliable and versatile program for subsidence management methodologies. Most recently, the program has been updated to evaluate the effect of varying surface topography in the prediction of horizontal displacements, referred to as ground strain, allowing for the accurate three-dimensional representation of surface deformations in mountainous terrain (Agioutantis and Karmis, 2014). Ground strain has become one of the predominant deformation indices used in the evaluation of potential damage to surface structures (Karmis et al., 1995). Ongoing work with SDPS software seeks to investigate the calculation of ground strain in SDPS and its ability to accurately and realistically predict damage to surface streams due to underground mining operations."

Jan 1, 2015

By Yeon-Ho Jin, Eui-Haeng Heo, Yun-Seok Park, Sung-Oong Choi, Hyung-Dong Min, Min-Su Jeong, Seung-Joong Lee

As rock fragmentation in bench blasting can affect the following process such as loading, hauling and crushing, its good control is essential for assessment of blasting efficiency and production cost.

Jan 1, 2015

By L. Trytten, S. Bass, P. Nawrocki, J. Mercer

The Sherritt Fort Site nickel refinery and fertilizer plant has been operating continuously since 1954. The ammonia leach process uses ammonia and sulphuric acid, producing nickel and cobalt and an ammonium sulphate byproduct. One of the features of an ammonium sulphate based process is the aggressive nature of ammonium sulphate to concrete and structural steel. After six decades of operation, portions of the structural steel and concrete at the Sherritt facility have become degraded. Infrastructure replacement programs started in earnest more than a decade ago with pipe racks and electrical infrastructure, and have now progressed into building steel. Replacing and repairing this infrastructure within the tight constraints of an operating plant poses several difficult challenges. This paper will outline the approach taken to accomplish this difficult work, and discuss key learnings from the ongoing program.

Jan 1, 2015

By F. T. Wang, Y. Yuan, S. H. Tu, X. G. Zhang

Hydraulic support instability (HSI) is one of the most common causes of disasters in underground coal mining, posing a threat to the safety of mine workers and normal operation of the equipment. It is prone to occur in fully-mechanized mining faces with a large mining height (FMMLMH), especially when the dip angle of the coal seam is large. The key to controlling HSI is to deduce its mechanism and employ effective control techniques. This paper focuses on the analysis of HSI types, the key parameters and techniques to control HSI in FMMLMH, the establishment of a model of HSI in FMMLMH, and a multi-parameter sensitivity mechanical model of different HSI forms in the no. 7219 longwall face in Xutuan Coal Mine, Huaibei Mining Group, by using sensitivity analysis . The results show that HSI mainly presents in three forms: hydraulic support gliding (HSG), hydraulic support tilting (HST), and hydraulic support tail twisting (HSTT). The occurrence of the above three forms depends mainly on support anti-instability capability. In the no. 7219 longwall face, HSG and HST are the main two forms of HSI. The dip angle of the working face and the friction coefficient between floor and hydraulic support are the sensitive parameters for HSG, while HST is strongly dependent on the dip angle of the working face and the friction coefficient between roof and hydraulic support. By the applications of measures such as the oblique layout of the working face, cutting the floor into a step pattern, moving the support under pressure, and raising the setting load, the support stability was controlled effectively.

Jan 1, 2015

By A. C. Gagnon, H. Saroglou

"The focus of this paper is on the analysis of geometrical discontinuity properties for the rock mass located within an open pit mine located in Western Africa. Discontinuity data were collected using various techniques including oriented core logging, borehole televiewer surveys, surface pit wall mapping and photogrammetry. The geological setting was initially studied prior to the data analysis to produce threedimensional ground models of the regional and mine site geology along with block diagrams illustrating predicted fracture patterns. Stereographic and statistical discontinuity data analysis of the geometrical properties of the rock mass was subsequently performed to identify unique structural domains throughout the open pit area. The discontinuity data collected throughout the studied open pit area were primarily discontinuity orientation, frequency and spacing and the investigation focused on the reasons for observed differences between the various data collection techniques. Stereographic analysis was used to assess the preferred geometry of discontinuities filtered by lithology, data collection technique, borehole, discontinuity type and pit wall (footwall or hanging wall). The observed fracture pattern is explained adequately by the geological setting. The need for accurate ground models for the design of open pit slopes is highlighted.INTRODUCTIONThe Tasiast Mine is an open pit operation located in north-western Mauritania, approximately 300 kilometres north of the capital Nouakchott. The Tasiast mine, which is owned and operated by Kinross Gold Corporation (Kinross), began commercial operations in 2008. The Tasiast mine is located in an area characterized by flat desert terrain within the western reaches of the Sahara Desert region. The current mine site includes mill buildings, shop facilities, waste dumps, tailings facilities and two main open pit operations (Piment and West Branch). The West Branch pit is the focus of this paper. The current open pit plan for West Branch indicates a final pit measuring approximately 2.5 km long by 1.4 km wide and 510 m deep."

Jan 1, 2015