Search Documents

By D. Kimball, P. Chambers

"BACKGROUND In the event of an explosion or fire in an underground mine, workers can be exposed to a deficiency of oxygen, an excess of carbon monoxide, or both. These threats can occur as separate conditions or simultaneously. A lack of oxygen in the breathing air can only be addressed via the use of a self-contained breathing apparatus (SCBA) acting as a source of oxygen. An excess of carbon monoxide can also be addressed via the use of an SCBA, but if the threat occurs in isolation (that is, the atmosphere still contains sufficient oxygen to support life) and the concentration of the threat gas is not extreme (< 2%) then the carbon monoxide threat can also be addressed by the use of a filter self-rescuer (FSR). Used together, the SCBA and FSR offer a far more efficient and universally capable life support system than when used in isolation. However, the SCBA does not take advantage of the fact that the surrounding atmosphere likely contains some level of useable oxygen; i.e., the SCBA always supplies the total required oxygen from its limited supply, resulting in a ceiling on its useful life regardless of the level of oxygen in the surrounding air. To address this technology gap, what is needed is a ""smart"" SCBA that provides filtration and catalytic protection against threat gasses and has an extended duration life-sustaining oxygen inhale stream independent of the threat content and oxygen deficiency of the surrounding atmosphere. DEVELOPMENT Developed under contract with NIOSH the Smart Escape SCBA is comprised of three major components including; 1) oxygen supply, 2) oxygen sensing & dosing electronics and, 3) a CO catalyst and carbon bed broad spectrum FSR. The SCBA is designed as a hybrid system that provides non-toxic breathing air by using an approved Chemical, Biological, Radiological and Nuclear filter self-rescuer and a catalyst to convert high levels of carbon monoxide to harmless carbon dioxide (CBRN FSR/CO). In addition, the Oxygen Sensing & Dosing Electronics (OSDE) package adds sufficient oxygen to make up for deficiencies detected in the ambient air (Figure 1). By making use of the ambient oxygen, less oxygen is required for a one-hour unit life. This means that the Smart Escape SCBA fits in a smaller and lighter package than a similar-duration conventional Self-Contained Self-Rescuers (SCSR). Alternatively, taking advantage of available ambient oxygen could offer a significant increase in working duration in a unit with the same size as current SCSRs. The research performed under this NIOSH contract involved numerous tasks including: (1) definition of performance and system requirements for the Smart Escape SCBA, including keeping environmental stressors within acceptable ranges, providing at least one hour of breathable oxygen supply, and using a mask or hood that allows high-quality voice communication; (2) designing, building, and evaluating prototype units to support extensive bench top testing at Avon Protection and third party labs to demonstrate the device’s capabilities; (3) building sufficient quantity of Smart Escape SCBAs designed to be intrinsically safe (per MSHA criteria); (4) testing and evaluation by the National Personal Protective Technology Laboratory (NPPTL)."

Jan 1, 2015

By Calvin Konya, Anthony Konya

State and Federal construction specifications require the Blasting Contractor to prepare a Master Blasting Plan which is reviewed by the Owner’s Representative. The Master Blasting Plan requires the Contractor to submit the design of a typical blast. Most blasting specifications also require the Blasting Contractor to submit Daily Blasting Plans. The Master Blasting Plan and the Daily Blasting Plan require that the Blasting Contractor also submit the types and quantities of explosives and initiators used. The specifications also request that the Blasting Contractor submit the pounds of explosive used per delay for both production and presplit blasts. The Blasting Contractor may also be required to predict the anticipated ground vibration and air overpressure levels for the proposed blasts. There are equations that can be used to predict the ground vibration. There are also equations that can be used to predict the air overpressure levels. The data for these equations were primarily derived from quarry and surface coal mine and some construction blasts. Data from major construction projects were analyzed in this study to determine new air overpressure propagation equations for construction blasting. These new prediction equations compare calculated results analyzed from field data with other existing air overpressure prediction equations. Production blasting air overpressure values are also compared to air overpressure from presplitting

Jan 1, 2015

"Shales play a major role in the stability of slopes, both natural and engineered. This paper attempts to provide a review of the state-of-the-art in shale slope stability. The complexities of shale terminology and classification are first reviewed followed by a brief discussion of the important physical and mechanical properties of relevance to shale slope stability. The varied mechanisms of shale slope stability are outlined and their importance highlighted by reference to international shale slope failures. Stability analysis and modelling of anisotropic rock slope masses are briefly discussed and the potential role of brittle rock fracture and damage highlighted. A short review of shale slopes in open pits is presented.INTRODUCTIONShales have been stated to form approximately 58% of sedimentary rock so it is not surprising that they are frequently encountered in both natural and engineered slopes. They represent challenging environments for slope stability due to the wide variation in their engineering properties, their changing behaviour with time due to geomorphic processes and the variation in the failure mechanisms as a function of both stratigraphy and tectonics. An extensive body of literature exists on the terminology and classification relevant to shales; it is not possible in the scope and length of the current paper to review these works in detail and the reader is referred to Farrokhrouz and Asef (2013), Bell (2000) and Goodman (1993) for detailed discussions. It is arguably the case that no universally accepted classification of shales exists today and depending on the field of application the terminology varies widely. Shales in slope stability, for the purpose of this keynote paper, are taken to include material varying in properties from weak rocks to soils and therein lies one of the most challenging aspects in shale slope characterisation for engineering purposes. They have been classified as “rock-like” or “soil-like’, (Underwood 1967) or compacted and cemented, Table 1, Yagiz (2001). Classifications have considered numerous factors including composition, cementation and a wide range of engineering properties.The propensity of shales to degrade with time due to geomorphic processes has resulted in an important aspect in their classification, that is, the attempts to incorporate slaking, durability and swelling and softening behavior through purpose developed testing methods (Gamble 1971, Morgenstern and Eigenbrod, 1974). Figures 1 and 2 show examples of terminology used to describe argillaceous materials and some proposed engineering classification schemes (Grainger 1984 and Bott 1986). Corominas (2014) provides a recent classification of argillaceous rocks and their durability relating five stages of slope deterioration to the texture of the rock on Ternary diagrams. No attempt will be made here to discuss the merits of the proposed terminology and classifications, suffice it to say, that the controversy and flux surrounding these issues is a strong indicator of the complexities in the behavior of these materials. In this paper the author will consider slope stability in the materials indicated in Table 1, Figures 1 and 2 without undue focus on terminology. At the lower strength limit of shales the engineer must design slopes using the principles of soil mechanics which may vary from the simple Mohr Coulomb plasticity constitutive criterion to modified critical state models, some even attempting to incorporate softening behaviour in the weaker clay shale materials. Given the transitional nature of shale materials several workers have treated overconsolidated clays and clay shales using concepts such as peak and residual shear strength, brittleness index and softening. Martin and Stacey (2013) provide a useful review of the importance of weak rocks in open pit mining, with mudrocks as a specific member, and note the importance of delayed failure, progressive failure and loosening in the stability of"

Jan 1, 2015

By F. Henríquez, V. Iriarte, L. Vinnett, J. Yianatos, F. Díaz

Metallurgical characterizations of the collective (Cu/Mo) and selective flotation plants were carried out in Minera Los Pelambres, Chile. The selective plant allows the valuable minerals of Cu and Mo to be separated. The evaluation involved two surveys consisting of metallurgical sampling as well as residence time distribution (RTD) measurements to determine load distribution. The RTD data were obtained in real-time by means of the radioactive tracer technique. In addition, metallurgical data was reconciled and supported by effective residence times. In the collective plant, a performance comparison of parallel rougher circuits was carried out, which included a bank of six mechanical cells of 250 m3 and banks of nine mechanical cells of 130 m3. In the selective plant, the Cu and Mo evolution along the plant was evaluated. The results in the selective plant allowed for performance evaluation of mechanical and pneumatic cells in primary flotation. In both plants, mineral losses were evaluated and their relationship with circuit configuration (cell types and circuit layout) was determined. The metallurgical characterization was a powerful tool to evaluate circuit performance and to detect improvement opportunities at industrial scale.

Jan 1, 2015

By A. Dahi Taleghani, Amir Shojaei

A continuum damage mechanics (CDM) based constitutive model has been developed to describe elastic, plastic and damage behavior of rock during drilling. In addition to inelastic deformations, this model incorporates rock anisotropies like toughness anisotropy due to the bedding planes orientation that is a common observation in soft Shales. The pressure sensitive inelastic deformation of porous rocks together with their damage mechanisms are studied for drained and undrained conditions. Fracture mechanics of microcrack and micro-void nucleation and their coalescence are incorporated into the formulation of the CDM models to accurately capture different rock failure modes. The performance of the developed elastoplastic and CDM models are compared with the available single cutter test data of a specific shale play and then the models are introduced into a commercial finite element package through user-defined subroutines. A workflow to derive the required model parameters is presented through inverse modelling of the single cutter test data. The developed CDM model outperforms the traditional discrete element and fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures like formation of the cuttings ribbon without any essential need for remeshing. This model would provide a robust tool for modeling bit performance and rate of penetration using conventional elements of FEA with a reliable results and a computational cost less than similar computational techniques like discrete element methods.

Jan 1, 2015

By Song-yu Liu, Chao Yan, Yong-feng Deng

"In order to investigate the stability of embankment on soft subgrade improved by T-shaped deep mixed column composite foundation, the internal forces and failure modes of columns were analyzed on the shape of critical slip surface and the displacement fields of composite foundation through strength reduction method of three dimensional numerical simulation. Then comparison between T-shaped and conventional deep mixed column composite foundation were conducted. The simulation results indicate that the stability analysis was overestimated by limit equilibrium methods. Piles within the slope shoulder provide great resistance slide effect through the vertical bearing capacity, while the piles nearby slope shoulder and outside slope shoulder providing great moment to resistant slip. The embankment stability of T-shaped deep mixed column composite foundation is higher than that of conventional deep mixed column composite foundation while cost less cement and construction time.INTRODUCTIONThe soft soil has many unfavorable project properties such as high compressibility, low strength, and high water component. Embankment built on the soft soil will face subsidence, horizontal displacement and stability problems. Cement-soil deep mixed column composite foundation is more commonly used as a method for construction of embankment on soft ground [1-2]. For the existing problems of China's current cement-soil pile (wet jet mixing pile), including strength uneven, effective treatment with shallow depth and high cost, a new technique, T-shaped bidirectional deep mixed column, is introduced [3]. An automatic expanding mixing blade was developed by Liu et al. shown in Figure. 1, to install TDM columns [4].T-shaped deep mixed (TDM) column combines bi-directional deep mixing technique and T-shaped deep mixing technique: ?Using concentric biaxial drill pipe, opposite rotational direction of the blade on the inner drill pipe and the outer drill pipe. By squeezing action of the blade on the outer drill pipe, forward and reverse rotation of the blades bidirectional mixing at the same time, blocking the way to take the grout, the uniformity of cement mixing is improved. ?Scalable stirring blades, which can be stretched for two different radius at any depth below ground, expand cross-section of the upper pile (enlarged head), forming expanding cross-section within the upper part of a certain depth which is similar to the shape of nail. As a new composite foundation, T-shaped mixing pile composite foundation is widely applied. However, studies on the stability of T-shaped column treated soft subgrade are rare in the research. So the stability study on T-shaped column composite foundation under embankment for guiding the design and construction has important significance."

Jan 1, 2015

By Z. G. Tao, Y. Y. Peng, W. L. Gong, M. C. He

"This paper presents an overview of the major landslide hazards in open pit mines in China, the currently used landslide control and monitoring techniques, and development of a new slope control technique incorporating the reinforcement, sliding force monitoring, remote sensing and forecasting in one system in order to constrain the displacement of the sliding blocks in the landslide to minimized the influenced area and provide precise warnings timely for the imminent landslides. For implementation of the new technique, a novel rock cable with large deformation and high resistance (also known as HE cable) was developed, which can elongate as long as 2m. At the same time, the necessary and sufficient condition for initiating a landslide and energy balance equations are formulated. Based on the proposed mathematical models and Beidou satellite system, the software and data transmission hardware for remote sensing and forecasting were developed the new landslide control technique has been applied successfully in 245 landslide sites in 12 provinces across China. In this article, two practical application cases in the open pit mines are reported.INTRODUCTIONChina is one of the countries in the world with the most widely distributed landslides and suffering the heaviest damage. According to the incomplete statistics, landslide hazards have caused death of hundreds of people and direct economic losses of several hundred million RMB each year. The landslide hazards have a great impact on the life and property safety of the people, safety of the infrastructure, as well as the social stability. Thus development of new techniques for forecasting and prediction of the landslides is imperative and of great importance. In general, the forecasting and prediction of the landslides consists of three major aspects, i.e. sliding time forecasting, landslide activity intensity forecasting and landslide hazard degree forecasting. Since a considerable part of the landslide-suspected area are adjacent to the residential areas or important infrastructures, development of the advanced landslide control and monitoring techniques to cope with the sliding time forecasting problem is more important.Over the past one hundred years, the most widely used slope monitoring techniques are based on displacement monitoring (Xu, et al. 2007; Toshitaka, 1998). In the early days owing to the limitation of the technology and equipment, the ground surface displacement and underground water level change were inspected mainly by man power for inferring the possibility of a landslide. In recent several decades, more and more ground surface displacement monitoring devices were brought to the market, such as the automatic total station, theodolite, digital level, borehole inclinometer and GPS based instruments, etc. Based on these modern techniques, some advanced instruments have been developed and applied to the landslide monitoring, for example, the “landslides early warning monitoring system” (Leonardo, et al. 2002), the “In-SAR” technique (Reevea, et al. 2000), the GPS and satellite geodetic survey based technique (Reevea, et al. 2000), and real-time telemetry technology (Xu, et al. 2007). These monitoring approaches have made significant contributions to the landslide disaster monitoring and forecasting. The major limitations for the ground surface displacement monitoring techniques are lie in the inconsistence between the displacement in ground surface and that in the sliding surface for the sliding mass, resulting in low degree of forecasting accuracy."

Jan 1, 2015

By Y. Mitani, H. Ikemi, K. Kitamura, H. Honda

"Instead of carbon capture and geological storage (CCS) that does not rely on structural aquifers, injecting carbon dioxide into sedimentary rock deep underground has been considered. For advection velocity of the fluid is slow, the permeability of sedimentary rock deep underground is low. In order to perform the CCS on the low permeable sedimentary rock, it is necessary to clarify the behavior of long term storage properties of carbon dioxide (CO2).In this study, the permeability and storativity of CO2 injected into low permeable rock has been evaluated. The injection of supercritical CO2 has been conducted on the specimen of Ainoura sandstone (unit weight: 2.39 g/cm3, porosity: 11.9 %) saturated with water by using flow pump method. The experiment has been set up to reproduce the similar condition of deep underground reservoir under 20 MPa confining pressure, 10 MPa pore pressure, 35°C temperature and 3 µl/min CO2 injection rate. In order to prevent an increase in pore pressure, the boundary condition on the outlet side of specimen has been kept a constant pressure.As a result, it has been possible to observe step by step the change of the differential pressure between both ends of specimen. Furthermore, the relative permeability and specific storage of rock under supercritical CO2 injection has been examined by the theoretical analysis of flow pump permeability test incorporating Darcy’s law for two-phase flow. It is observed that CO2 has been transmitted gradually while CO2 stored in the rock. It is also clarified that residual water has existed in specimen after showing the constant differential pressure in the end of the experiment. Using the results of the experiment, 3D core-scale flow-simulation by using TOUGH2 has been conducted due to confirm the flow of fluid and CO2 distribution in the specimen. From the experimental results and analytical solution to them, permeability and storativity are identified, and simulation results support the validity of the experimental results."

Jan 1, 2015

By M. Proulx

"RÉSUMÉ Le diagramme ternaire Al2O3-Sr-Y est un nouvel outil servant à l’exploration de gisements de sulfures massifs volcanogènes (SMV) archéens. Le diagramme permet de discriminer entre les roches volcaniques à minéralisations à zinc dominant (domaine Zn+) et celles à minéralisations à cuivre dominant (domaine Cu+), ainsi que les roches volcaniques ayant subi une chloritisation hydrothermale pouvant aboutir à la formation de chloritites associées aux cheminées d’altération (domaine Cl+). Ces trois domaines délimitent des zones d’influence géochimique ou d’empreintes hydrothermales résiduelles ou fossiles produites par les cellules de convection hydrothermales générées par des magmas. Le diagramme permet aux sociétés d’exploration de déterminer de façon peu coûteuse la fertilité potentielle des roches volcaniques archéennes en ayant recours à leurs bases de données et aux résultats de leurs analyses de terrain, sans aucune manipulation des données. Le diagramme ne s’applique pas aux SMV aurifères.ABSTRACT The tertiary diagram Al2O3-Sr-Y is a new tool to explore Archean volcanogenic massive sulphide (VMS) deposits. The diagram can be used to discriminate between the volcanic rocks where zinc is the dominant mineralization (Zn+ domain) and the rocks where copper is the dominant mineralization (Cu+ domain), as well as the volcanic rocks that were subjected to hydrothermal chloritization that could have led to the formation of chloritites associated with alteration chimneys (Cl+ domain). These three domains define the zones of geochemical influence, or residual or fossil hydrothermal footprints produced by hydrothermal convection cells generated by magmas. Exploration companies can apply the diagram to determine, at low cost, the potential fertility of the Archean volcanic rocks by using their databases and the results of their field analyses, without any data manipulation. The diagram does not apply to gold-bearing VMS deposits."

Jan 1, 2015

By Elizma Ford, Vincent Sithole

"Two shortened test procedures for estimating the Bond ball work index are compared for suitability of use on Zambian/DRC-type copper–cobalt ores. The first procedure is based on a batch milling test while the second procedure is based on a limited locked-cycle test. Both procedures were conducted using a standard Bond test mill. INTRODUCTION The Bond ball work index is widely used in the field of minerals processing as an indicator of ore grindability. The work index is determined by means of a locked-cycle test procedure that typically requires seven to eight cycles to stabilise at a re-circulating load of 250%. A typical test requires between three to four kilogram of ore sample and around eight hours of operator time. For geometallurgical test work applications, where a large number of variability samples are to be tested, it would be highly beneficial to use a test procedure that requires less sample mass and operator time. Certain test work laboratories, for example SGS and JK Tech, are already offering various types of shortened test procedures for estimating the Bond ball work index. This paper discusses a comparison of two shortened test procedures that were evaluated for suitability of use on Zambian/DRC-type copper–cobalt ores. EXPERIMENTAL Test Procedure 1 – Batch Milling The first test procedure is derived from a batch milling approach proposed by the University of Hacettepe (Aksani, 2000). Some modifications were, however, made to the data analysis method from that originally proposed. During this test procedure, a 700 mL volume of sample is milled in a standard Bond test mill for a pre-determined number of revolutions. The feed and product particle size distributions are measured for each test. These results are then used to back-calculate a cumulative breakage rate parameter (k) for each particle size, according to the following formula:"

Jan 1, 2015

By R. C. Fernandes, F. L. Santos

Aluminum alloys in particular, have certain limitations when subjected to welding process. This is mainly present because aluminum alloys have high thermal conductivity, high contraction in solidification and high hydrogen solubility. Taking this into account, the FSW process has great potential for this application, since it is autogenous, held without metal melting and without the use of slags or shielding gases. From this concept, the aim of this study is to evaluate the joining of thin sheets of aluminum alloy 3105 H26 with 0.7 mm of thickness. To performing of the tests, some parameters were analyzed, such as: tool penetration in the sheets, attack angle, the type of welding tool and penetration control mode (position or force). The results indicated that the force control mode is most suitable for thin sheets, and the transient state at the beginning of welding was the most critical part to control the welding quality.

Jan 1, 2015

By Z. Liang, Z. Q. Liu, X. F. Li, H. L. Zhang

"Dynamic characteristics of frozen soil is important for the safe, effective and rapid construction in cold regions and artificially frozen engineering. In this paper, dynamic characteristics of frozen clay with various low temperature and different strain rate were studied by using Split Hopkinson Pressure Bar (SHPB) test and numerical simulation test. Variation of dynamical parameters and dynamic stress-strain curves of frozen clay were obtained and analyzed. The results of these test show that: Frozen clay exhibits temperature effect and strain rate effect that the failure type tends from plastic failure to brittle failure with the increase of strain rate or decrease of temperature; Under impact loading, frozen clay exhibits three typical dynamic stress-strain curves as strain rate increases, and the maximum strain of frozen clay only linear increases with strain rate.INTRODUCTIONArtificial freezing technology has been widely used in the construction of underground engineering, such as the coal mine shaft, the deep foundation pit, the urban metro and subsea tunnel, etc. Research on dynamic mechanical behavior of artificial frozen soil will provide supports for these artificially frozen engineering (Xu et al. 1998; Ma 2009). However, the dynamic mechanical research on frozen soil is mainly carried out at low frequencies or small amplitudes of the waves, behavior of frozen soil under impact loads or high strain rate loads has not been made clear."

Jan 1, 2015

By A. Ortigão, M. Felix, E. Falk, T. Koehler

"Ground improvement techniques such as vibro-replacement or deep soil mixing are fairly young products in the Brazilian geotechnical market. Soft soils in this country are deep, very soft, have low sensitivity and are challenging. In general, ground improvement techniques are increasingly selected as more costefficient and flexible solutions on infrastructure projects compared to the conventionall technologies such as piled embankments, wickdrains with surcharge or jet-grouting. The geotechnical challenge expansion project for the Porto Alegre Airport, South Brazil, involved a taxiway area of five ha of 8 to 10 m of soft clay deposit. The deep soil mixing (DSM) technique was selected as a cost-effective solution to reduce settlements. As part of the design, an extensive soil investigation programme includ ing laboratory and field trials was carried out to define the most economical slurry-recipe, DSM installation patterns and quality control specs. This paper gives details of the field and laboratory trials and present results.INTRODUCTIONThe International Airport of Porto Alegre in the state of Rio Grande do Sul in Brazil is located in an area with extensive sediments near to Guaíba Bay. During the different construction phases of the airport over the last decades, the soft clay deposits have been a challenge for the local geotechnical community as well as for the specialized contractors (Schnaid et al, 2001). As part of the most recent expansion scheme, a cargo-terminal with a five ha airplane tarmac area will be constructed."

Jan 1, 2015

"Increasing demand and market economics have pushed the mining industry to adopt improved mining practices and minimize losses. Simulation, in this regard, has proved to be an efficient tool to help in decision making purposes. We present the development of a discrete event simulation model for a large-scale open pit mine to run experimental scenarios for near optimal decision making. A mixed integer linear goal programming (MILGP) optimization model is also presented for shovel allocation optimization. The mathematical model will be coupled with the simulation model at the dispatching stage for shovel allocation optimization and thus it will act as the link to optimal short-term schedule to assist in achieving better mine plan compliance across short-term and operational planning time horizons. The main contribution of this work so far is the development of the MILGP model and development, implementation and verification of the simulation model on a large scale oil sands open pit mine case study. The results obtained so far are promising and have been validated against the historical data of the mine, proving the applicability of the model for experimental scenario analysis. INTRODUCTION It is essential for mining operations to adopt efficient operational methods and technologies to cope with market demand and economics. Mining operations, on the other hand, being capital intensive, find it risky to bring in any changes. Simulation is a tool that can help in this regard for better decision making purposes with an improved and quantitative measure of confidence. A true representative model that satisfies the objectives set for the simulation is essential to achieve its applicability for decision making purposes. A similar simulation model is presented in this paper for analyzing the operational KPIs of a large scale oil sand open pit mine with truck-shovel operations. This paper is aimed at providing an overview of the development of the model and the statistical outcomes validating its applicability for experimental scenario runs and thus for better decision making purposes. A mixed integer linear goal programming (MILGP) optimization model is also presented in this paper that acts as an upper stage in a multi-stage dispatching system. The optimization model is proposed to be linked with the dispatching logic in the simulation for optimal shovel assignments and target productions by reading available mining faces directly from the short-term extraction schedule. This model is aimed at bridging the gap between operations and short term extraction schedule; and may help achieve better compliance between the two."

Jan 1, 2015

By J. H. Cloete, S. M. Bradshaw, D. K. Chibwe

"Modern tundishes have evolved as vessels to serve as the final step in refining of molten steel by removing inclusions and promoting thermochemical homogeneity.In this study the flow behaviour in a four-strand tundish was investigated by means of a ½-scale water model as well as numerical modelling. The numerical and physical models were used to characterize residence time distribution and calculate properties pertaining to tundish flow regime. Three different tundish configurations were investigated: a bare tundish with no flow control devices, a tundish with a turbulence inhibitor, and a tundish with both a turbulence inhibitor and a dam.The physical and numerical models showed that a tundish without flow control devices is prone to significant short-circuiting. A tundish with a turbulence inhibitor was shown to be successful in preventing shortcircuiting and provided surface-directed flow that might assist the removal of inclusions from the melt. However, it was also observed that the upward-directed flow caused the maximum turbulence kinetic energy near the surface to increase dramatically. The potential for slag entrainment should therefore be considered during the design and operation of tundishes with turbulence inhibitors."

Jan 1, 2015

By A. G. Doll

"Multi-stage crushing plants, including high pressure grinding roll (HPGR) circuits, require more materials handling equipment than SAG and ball mill circuits. A temptation exists to neglect the energy consumption of materials handling when doing desktop comparisons of HPGR versus SAG milling circuits because estimation of materials handling power requirements can demand significant general arrangement drafting that is not available when performing preliminary scoping or ""desktop"" studies.The largest component of materials handling power is consumed by conveyors when lifting material between stages of crushing, meaning that a simple potential energy model can be used to evaluate conveying specific power consumption. This potential energy consumption for conveying can then be factored to provide overall materials handling specific energy consumption suitable for desktop studies of HPGR and other multi-stage crushing circuits. The technique also permits different crushing circuit flowsheets to be evaluated, at a preliminary level, by simply counting the number of times a conveyor must ""lift"" ore from ground level up to a bin or other equipment mounted up high.INTRODUCTIONTrade-off studies of multi-stage crushing plants involving high pressure grinding rolls (HPGRs) versus semi-autogenous grinding (SAG) mill circuits typically focus on the operating cost savings of crushing plants versus the capital cost savings of SAG mill plants. Very high-level (or desktop) studies of this type do not include a great deal of engineering work, meaning that the details (and costs) of ancillary systems are often not captured when doing the comparisons. The more complicated nature of the multistage crushing plants means there are more ancillary systems than a SAG mill plant, risking a skewed analysis of the operating costs, benefiting the HPGR option.One of the ancillary systems that may be overlooked is the more complicated conveying systems inherent in multi-stage crushing plants. Due to the mass of material being handled in large mining operations, these conveyors become a significant portion of the operating costs. A simple way to estimate the specific energy consumption of conveying systems without requiring engineering drawings and a site layout would allow high-level studies to capture this operating cost."

Jan 1, 2015

By J-P. Rossetti, A. Guerin, M. Jaboyedoff, L. Baillet, A. Mariscal, J. D'Amato, D. Hantz

"The processes leading to the fall of rock compartments from rock walls are poorly known as well as their velocity. It ensues that quantitative prediction of the failure time for a rock compartment which is presently stable, is not possible by a purely geomechanical approach. However a quantitative probabilistic prediction of rockfalls at the scale of a rock wall is possible if the spatial-temporal rockfall frequency can be determined or estimated (Hantz, 2011). For a better knowledge of failure processes and frequency, rockfalls have been detected in several rock walls, using annual terrestrial laser scanning, allowing comparison of the frequencies in different geological conditions. For one of these rock walls, the spatial detection have been completed by a precise dating of the events, using a quasi-continuous photographic survey (one photo every 10 mn), allowing the study of the influence of meteorological factors.The precise dating of rockfalls has been carried out for the Saint-Eynard cliff which towers above a residential area of the town of Grenoble (French Alps). The South-East facing cliff consists in bedded limestone gently dipping North-West and located at an elevation between 850 m and 1100 m. The surveyed zone is about 750 m large and 250 m high. Between 01/02/2013 and 26/11/2013, 65 rockfalls ranging between 0.01 m3 and 20 m3, have been detected by diachronic comparison of laser scanner data and dated by comparison of photographic images. The temperature at the elevation of the cliff has been calculated from the temperature measured (every 5 mn) at a meteorological station located at an elevation of 245 m and 2.5 km away from the cliff, using a temperature gradient of 0.003°C/m (D’Amato et al., 2014). The precipitation were measured 900 m away from the cliff at an elevation of 469 m. Different meteorological conditions have been defined: (a) “freeze” qualifies days with negative mean temperature (but with a thaw period, except for two days); (b) “thaw” qualifies days with positive mean temperature, but following a freeze day; (c) “rain” qualifies days with precipitation.Table 1 shows the rockfall temporal frequency for the different meteorological conditions. It appears that the frequency is about 6 times higher the freeze days, 2.5 higher the thaw days and 3 times higher the rain days than days without freeze, thaw or rain."

Jan 1, 2015

By M. Sukhram

In the year 1992, T.A. Utigard published a paper titled "The measurement of the heat-transfer coefficient between high temperature liquids and solid surfaces." In that work, he instrumented an agglomerate of materials with thermocouples to infer the heat transfer coefficient of a high temperature liquid on a solid. The purpose of that research was to help in the design and operation of metallurgical reactors. Since that time there have been many researchers that have worked to characterize heat, mass, and momentum transfer phenomena in high temperature metallurgical processing operations. This paper presents results from the author’s experience with instrumenting thermocouples in copper elements coated with carbon to infer velocity of high temperature liquid metals. It also presents a methodology to determine velocity of a high temperature liquid by inferring the local heat transfer coefficient at a solid-liquid interface

Jan 1, 2015

By Yang Zhao, Wanping Wang, Siqing Liu, Shuming Wen

"In China, most reserves of rich iron ores have now been depleted and sustainable development of low-grade iron ores has become a critical discussion topic in the mining industry today. The aim of this study was to evaluate the applicability of beneficiating a low-grade, hematite-magnetite ore (assaying 18.64% Fe) for subsequent utilization. In this study, process mineralogy and beneficiation of the ore were carried out in the laboratory. First, mineralogical investigation shows that the main metal minerals are hematite, magnetite and a little octahedrite that cannot be used at present, and the main gangue minerals include albite, quartz and ankerite. Based on the above, a combined process of magnetic separation and gravity concentration has been developed by using laboratory low- and high- intensity magnetic separators and a slimes shaking table, respectively. Factors affecting these separation methods are discussed, including process mineralogy on the tailings of the high-intensity separator, where the iron minerals were found to be finely disseminated in the gangue as inclusions. By applying a two-stage grinding step and a magnetic separation stage together with gravity concentration, a marketable iron concentrate assaying 60.79% Fe at a recovery of 60.23% can be obtained, when the feed assays 18.75%Fe, which provides some useful information for the sustainable use of low-grade iron ore.IntroductionIron is the world’s most commonly used metal. Steel, of which iron ore is the key ingredient, represents almost 95% of all metal used per year, primarily in structural engineering applications and for maritime purposes, automobiles and general industrial applications. By the end of 2009, the iron and steel production in China ranked the first in the world, and reached 0.567 and 0.537 billion tons, respectively. The domestic supply of iron ore was 0.88 billion tons and about 0.628 billion tons of iron ore were imported in 2009."

Jan 1, 2015

By Tanaya Deb, Sujit Kumar Pal

"Experimental investigations are carried out on failure pattern around 2D models of belled anchor piles in dry sand bed of density 15.60 kN/m3 under uplift. The models are having thickness ratio (Ts/Tb) = 0.28, 0.32, 0.38 and 0.46 and total 12 numbers tests are performed on models possessing 45° bell angle and shaft thickness 26 mm. The foundation bed is prepared with alternate dyed and non-dyed sand layers and continued upto reaching embedment ratio of 3, 4 and 5 for each width ratio. The failure points are presented with respect to meridian section of anchor in X-Y coordinate system and the equations formed are of polynomial of degree 3; and R2 values are near about 1. The developed wedge is implemented as three-dimensional axisymmetrical failure surface around similar 3D models. In the horizontal slice method vertical limit equilibrium is used for calculating weight of wedge and mobilized shear (as per Chattopadhyay and Pise, 1986) on the slip surface of each element. The summation of all elementary forces demonstrates gross uplift capacity. The initial and final failure angles are detected and parametric study is conducted on failure pattern as well as predicted net ultimate uplift capacity. Almost all the analytical data are within ± 10% variations with respect to the experimental results of uplift capacity which shows better correlations. INTRODUCTION Belled or enlarged base anchor piles are attractive and economic alternative to the geotechnical engineers for compressive load bearing capacity as well as tension anchorage. These types of anchors may be useful for foundations erected below ground water table. In light weight structures like radar tower, television tower, power pole and outdoor sign pools imbalance horizontal forces due to wind loads, are more than of those self-weight of those structures. Due to chronic tensile loads most possibly from wind loads and associated imbalanced cable tension, the legs of power transmission tower should be properly designed to be safe against resultant pull-out forces. In belled anchor pile, uplift is influenced by embedment ratio, diameter ratio; so, contributions of these parameters on failure surface influence uplift capacity. Balla (1961) first introduced non-linear failure surface in the pattern of circular arc based on Kotter’s equation (1903) and soil friction was assumed to act on slip surface. The predictive mathematical models established by Matsuo (1967), Rao and Kumar (1987), Chattopadhyay and Pise (1986), Saeedy (1987) and Ghaly and Hanna (1994); it was reported that net ultimate uplift capacity was combination of bulk weight of failure wedge and shear resistance along slip surface acting in opposite direction of wedge movement. From the literatures available till date, it reveals that the contribution of mobilised shear and weight of breakout wedge separately, demanding for more clarification depending on the on parameters like embedment ratio, diameter ratio."

Jan 1, 2015