Search Documents

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By B. W. J. van Rensburg, M. J. Schmidt

Bulk materials handling systems are extensively used in the mining and minerals industry, where a fairly high incidence of structural failure is experienced, notwithstanding design compliance with appropriate standards. A number of case studies are explored to demonstrate how insufficient controls or protection systems have contributed to structural failures on mobile bulk handling equipment. The importance of design integration across engineering disciplines is highlighted. The revision of ISO 5049-1 (1994) is proposed to provide specific rules and guidelines pertaining to machine protection systems. It is further recommended that the structural design engineer of the original equipment manufacturer(OEM) fulfils a more prominent role during the final acceptance and handover of mobile bulk handling equipment, with specific reference to protection systems.

Jan 1, 2015

By Ali S. Fayad

"In June 2014, Orange County Flood Control District (OCFCD) completed construction improvements of the East Garden Grove-Wintersburg Channel for a price of $42 million. Instead of the pre-existing traditional trapezoidal levee, the channel was improved with a vertical compact levee. Dubbed Soil-Mix-Sandwich (SMS), this geo-structural and environmental solution for coastal channel improvements, underlain by liquefiable soil strata, was both a design and construction innovation. It employed Deep Soil Cement Mixing (DSCM) within the confines of a hydraulically-pressed (Giken Method) sheet pile duo. SMS was unique because it incorporated both subterranean and supra-dredge-line soil mixing within a very narrow workspace. Its DSCM pattern aimed at optimum densification of the workspace and was confirmed during the construction process. It availed the DSCM sub-contractor (Hayward Baker Inc.) the opportunity to demonstrate the fitness of their huge wet-mixing machinery within a very confined access-area and introduced approximately 70,000 cubic yards of DSCM within a limited 15 foot workspace width that stretched for a mile. The sheet pile duo created a construction-enclosure that became a stay-in-place load resisting system. PROJECT CHRONOLOGY AND LOCATIONAn Orange County Flood Control District (OCFCD) project-report was commissioned to study the East Garden Grove Wintersburg channel (OCFCD facility # C05). The report examined the hydraulic conveyance of the C05 channel and was concluded in 1994 by Williamson & Schmidt. The project-report did not encompass extensive geologic studies; but it provided several alternatives for channel improvement. It recommended a single row of sheet piles as the preferred alternative for the downstream reach.The most downstream reach of the C05 channel is located in an environmentally sensitive area, in City of Huntington Beach, California, USA. Its site includes seismic chasms that surface within the C05-footprint (the Newport- Inglewood tectonic fault). Extensive deposits of liquefiable soil exist beneath the channel. Furthermore, tidal-influence prevails against the channel levee. Implementation of a successful design for channel improvement emerged after several traditional concepts were deemed unacceptable by geotechnical consultants. OC Public Works (on behalf of OCFCD) was in need of a design and construction technique that mitigated many associated risks. From these circumstances, Soil-Mix-Sandwich was born and was referred to in the rest of this discussion as SMS. OC Public Works required the SMS design concept to undergo verification by independent geotechnical consultants. SMS chronology from conception to construction can be summarized as follows:"

Jan 1, 2015

By A. Tsekov, Stefan Neufeind, T. Angelov, G. Savov

"A complementary ion exchange/solvent extraction process for the recovery of copper from low-grade ores developed by Iontech Engineering Ltd. is described. It has successfully been implemented on a full-scale plant level at the Buchim Copper Mine in Macedonia, yielding a maximum copper cathode production of 2400 tonnes per year. Technical and economic aspects of three years of operational experience are comprehensively compared with the Asarel Medet copper plant in Bulgaria, which is utilizing conventional solvent extraction in the enrichment/purification step. INTRODUCTION The concentration and separation of copper from primary leachates is one of the key operations in the hydrometallurgical processing of oxide ores (Langner, 2011). Conventionally, this basic operation is conducted by submitting the pregnant leach solution (PLS), with a 1–5 g/L Cu content, from the initial sulfuric acid leach to a solvent-extraction (SX) process in which copper reports to the organic phase (see Figure 1). After phase separation, the metal is stripped from the extractant/diluent mixture employing sulfuric acid to furnish a concentrated metal solution, usually containing 40–50 g Cu/L. The final products of the overall process are copper cathodes, which are obtained from a terminal electrowinning step.Although considered as “technology of choice”, SX to date is still suffering from several drawbacks, such as the risk of poor phase disengagement and the high capital costs of solvent-extraction plants. Especially, the processing of leachates with lower copper tenors (< 1 g/L) is often economically less attractive. As a result, tremendous efforts have been dedicated to the evaluation of alternative technologies to address these challenges."

Jan 1, 2015

By W. Zhang

"The adsorption of collector on chalcocite has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). The AFM images show that xanthate, such as potassium ethyl xanthate (KEX) and potassium amyl xanthate (PAX), adsorbs strongly on chalcocite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. The result clearly shows that the adsorption of xanthate on chalcocite is totally different from its adsorption on chalcopyrite, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. AFM images also showed that increasing solution pH to 10 doesn’t prevent the adsorption of xanthate on chalcocite much and the result confirms with the fact that chalcocite floats well in a wide pH range up to 12 with xanthate being used as a collector. INTRODUCTION In flotation, the adsorption of collector on mineral surface is vital for a successful flotation process to achieve a satisfying metal recovery. Historically, many works have been carried out to clarify the adsorption mechanism of collectors on sulfides. (Gaudin and Schuhmann, 1936, Poling and Leja, 1963; Allison et al., 1972, Fuerstenau, 1982; Leja, 1982; Woods, 1984) The adsorption of xanthate on chalcocite surface in aqueous solution also attracted the interest of many researches. Gaudin and his colleagues (Gaudin et al., 1934; Gaudin and Schuhmann, 1936) studied the solubility of potassium ethyl xanthate and its reaction products in organic solvents and firstly proposed there was initially chemisorbed xanthate (X-) on chalcocite surface followed by insoluble cuprous xanthate (CuX). Allison et al. (1972) studied the reaction products of various sulfide minerals with xanthate solutions and reported that the measured rest potential of chalcocite in 6.25×10-4 M KEX solution at pH 7 was +60 mV and the reaction product of PAX on chalcocite was cuprous xanthate. Mielczarski and Suoninen (1984a, 1984b) applied the XPS and studied the adsorption of potassium ethyl xanthate on cuprous sulfide. It was reported that there was a relatively rapid formation of a well-oriented monolayer of xanthate ions followed by a slow growth of disordered cuprous xanthate molecules on top of this layer. Richardson et al. (1984) carried out an electrochemical study of chalcocite flotation with the addition of ethyl xanthate. It was proposed that cuprous xanthate and possibly cupric xanthate were adsorbed hydrophobic species on chalcocite surface due to the exchange and charge transfer oxidation reactions. Leppinen et al. (1989) applied an in-situ FTIR study of ethyl xanthate adsorption on sulfide minerals under conditions of controlled potential and they concluded that, for chalcocite, there were three different potential regions of xanthate adsorption, including chemisorption, copper ethyl xanthate formation on the surface and multilayer formation."

Jan 1, 2015

By Michael Hughes, Selva Selvamohan, Ray Costa

"Cutoff walls are commonly used to mitigate underseepage problems for levee remediation projects. At abrupt changes in seepage cutoff wall depths there is a potential for water to flow around the back of the deeper cutoff wall leading to elevated seepage pressures on the landside that could result in exit gradients exceeding design criteria. This condition is referred to as end-around-effects and is a complex problem that requires detailed and time consuming 3-D numerical modeling to represent accurately. This paper presents a simple approach for assessing end-around-effects using the results of 2- D seepage analysis to determine if lateral extension of the deeper portion of the cutoff wall is required. This simplified approach provides a pragmatic solution to a complex 3-D problem. The presented procedure was used as part of the Feather River West Levee Project in Yuba City, California, to assess end-around-effects at 26 locations. The results showed that wall extensions of up to 100 feet were needed at only 2 locations.INTRODUCTIONAs the lead geotechnical consultant for the Feather River West Levee Project, AECOM were responsible for designing levee remediation works for approximately 35 miles of levee protecting the area around Yuba City, California, and communities to the north and south. Due to land use constraints, seepage cutoff walls were the main remediation alternative selected to address underseepage issues for the project.As part of the design review process, the California Department of Water Resources (DWR) requested AECOM to look at 26 locations along the levee alignment where the depth of cutoff wall changed abruptly from shallow to deep, or vice versa. At these locations there was the potential for seepage pressures to pass behind the deeper section of cutoff wall and stress the blanket layer landward of the cutoff wall. A condition referred to as end-around-effects.End-around-effects involve complex 3-D ground conditions that have traditionally been addressed by laterally extending the deeper section of cutoff wall an arbitrary distance based solely on engineering judgment. In discussions with DWR, AECOM developed a simple procedure to provide a more objective assessment of end-around-effects without the need for detailed and time consuming analysis. This procedure allows the engineer to make an informed decision of whether end-around-effects are a problem at the location of a cutoff wall transition rather than laterally extending the deeper section of cutoff wall an arbitrary distance based on engineering judgment alone."

Jan 1, 2015

By Y. M. Chen, H. L. Zhang, W. U. Bing, C. Q. Zhou

Multiphase flow in the widely used Vanyukov furnace was numerically studied. An unsteady three-dimensional and three-phase flow model was firstly built using the computational fluid dynamics (CFD) software ANSYS FLUENT®, and then solved with the volume of fluid (VOF) and k - ??model. The results showed that the proposed model could be used to predict the multiphase movement, the slag/air fluctuation, the vortex formation, and effects of structural and operational parameters. By fast Fourier transform (FFT), the dominant frequency of density with time signal was calculated as 0.29 Hz. The analysis of different injection flow rates of enriched air indicated that this variable has a major effect on the mean slag velocity. The peak mean velocity increased from 2.17 to 4.99 m/s while the flow rate of enriched air varied from 70 to 160 m/s. The proposed model provides a method to optimize the furnace structure and operating conditions for the best furnace performance and lowest energy consumption.

Jan 1, 2015

By George Filz, Morales, Carlos, Bertero, Filippo Maria, Alessandro, Leoni

"The Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils for many practical applications. A pre-construction soil investigation campaign is necessary to assess soil properties and to retrieve samples of different soil layers for a laboratory Bench Scale Testing program (BST). The BST has to be designed using various binder types, binder contents, and water/cement ratios in each of the soil types. Following the laboratory program, a full scale Field Test (FT) is typically necessary to verify the results of the BST. This paper will highlight the differences and the importance of performing both pre-construction laboratory tests and field tests to ascertain the proper mixing parameters in the different soil layers. Comparative analyses and interpretations between the lab and field stages, along with accumulated information about soil properties and quality control (QC) results, allow fine-tuning the production parameters throughout a project. Three Deep Mixing Method projects, where both laboratory and field tests were executed, are illustrated: (1) The LPV 111 Project (New Orleans, LA, USA): DMM was used for ground improvement/foundation strengthening to stabilize and support the burden of a new levee raise; (2) The Rio Puerto Nuevo Project (San Juan, PR, USA): DMM was applied to improve the soils adjacent to a 90"" forced sewer main relocation and to improve the soils for the base of a new drainage channel; and (3) State Road 83 (US 331) over Choctawhatchee Bay project (Walton County, FL, USA): DMM was applied to stabilize the causeway sections of the bridge enhancement project. Data recorded during laboratory and field tests for these projects were analyzed and interpreted to select the most appropriate construction parameters to provide a final high-quality product.INTRODUCTIONThe Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils in many situations. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product.Generally a pre-construction soil investigation campaign has to be performed to assess soil properties and to retrieve samples of different soil layers for the laboratory Bench Scale Testing programme (BST). The BST has to be designed using various binder types, binder contents (or cement factors - CF), and grout water/cement ratios (W/C) in each of the soil types; the selection of the different combinations and dosages for the BST is based on past extensive experiences on similar materials. Following the laboratory programme results, a full scale Field Test (FT) has to be designed and executed, installing several DMM elements to verify the results of the BST and fine tune the construction parameters, with the appropriate binder type and dosage and the most effective equipment and tool configuration."

Jan 1, 2015

"With millions of dollars and thousands of lives at stake, the Iron Ore Company of Canada (IOC) turned to a private wireless network for help.IOC needed a network that possessed the ability to adapt to changes in a nanosecond and to function seamlessly in the most rugged of environments.Canada’s largest iron ore producer required a private wireless network powerful enough to support all mine applications and deliver all data to one central point — without any existing cellular/3G/Wi-Fi coverage.Operations at IOC, a leading global supplier of iron pellets, involved dispatch, drill management and equipment monitoring, pump control and remote video that must service three distinct pits. Due to its setup, the facility does not offer a great deal of flexibility for transmitting signals.IOC serves a robust customer base made up of North American, European and Asian steel producers. It also employs nearly 1,900 people. Catastrophic death and destruction are two very real potential consequences of system communication failure.Technology for tough terrainKinetic mesh technology was born in the wake of the 9/11 terrorist attacks on the United States, one of the most high-stakes emergency situations in U.S. history. The failure of the communications infrastructure on a massive scale that day underscored the need for networking technologies that could provide service even in the most chaotic of conditions.Kinetic mesh networks allow organizations to deploy networks at sites where communications infrastructure has been compromised, as well as quickly establish networks in places where they did not previously exist. Kinetic mesh networks have also demonstrated a better ability to adapt to network changes on-the-fly versus other types of networking technologies."

Jan 1, 2015

By C. Grisanti, E. Prina Howald

The major of Swiss territory is occupied by mountains. Natural events as floods, debris flows, landslides, rockfalls, and avalanches regularly threaten the safety of people and properties. On the one hand, extreme weather events cause great damages, on the other hand, the enhancement of territory’s exploitation increases the risk. The Swiss Government makes many efforts to deal with the prevention of natural hazards, especially through measures of land management. As stated by federal law, Swiss cantons are obliged to establish hazard maps and to take the risk into account in the land management. Hazard maps are based on the hazard matrix, whose abscissa and ordinate are probability and intensity of the event on site. This project focuses on rockfalls. It consists of three main parts: the creation of a database to collect data on site, the creation of a catalog with all type of measures, and the development of a methodology for the analysis of the effectiveness of protective measures. The creation of the database allows us to collect information: about the site, about protective structures implemented on it, and about failures. With many multiple choice fields and few free text fields, it can collect data in a homogeneous way, without redundancy. The catalog has to be a tool that gives a basis to make decisions. It collects information about all types of protective measures implemented on Canton Vaud’s territory or available on the Swiss market. Free text fields allow for data storage of specifics, to give a complete view of structure’s characteristics and potentials. Methodology consists of four steps. The core of the procedure is the structure’s evaluation following a score system; it allows for calculation of reduction factors that have to be applied to intensity and probability parameters of the structure. Then it is necessary to convert the reduced structure’s intensity value into a residual site’s intensity value. Although the first step enables us to choose suitable measure for a specific site, it is not necessary to perform it. Second step allows us to evaluate structures under scenario 0, where structures are in best conditions. Third step allows us to evaluate structures under six scenarios of possible failings. Fourth step allows us to convert structure’s reduced intensity into event’s residual intensity and to establish the new point on hazard matrix. While the procedure has already been defined, details of score system and conversion have to be developed during the second phase of the project.

Jan 1, 2015

By Nan Zhou, Jixiong Zhang, Qiang Zhang

"Mining activities under hard roof could easily induce rock burst. Based on the geological conditions of widespread hard roof in China, this paper discusses the type, mechanism of occurrence and prevention of rock burst caused by hard roof from energy evolution point of view. It analyzed the interaction between the solid backfilled body and roof under different backfilling ratios. And by establishing and applying the mechanical model, the deformation of hard roof and energy evolution of the panel under different backfilling ratios were determined, revealing the control effect of solid backfilling on disaster-causing energy. As a result, an innovative method using the solid backfilling method was proposed as a solution to the hard-roof-induced rock burst hazards. Moreover, mine trial was conducted in Panel 6304-1 of Jisan Mine. The result shows that the stress concentration factor of the front abutment stress was only 1.44; the coal dusts in drill holes didn’t exceed the limits and microseism of large energy didn’t occur during mining mining, indicating that solid backfilling mining could be applied as an effective method for preventing rock burst caused by hard roof.INTRODUCTIONSHard roof refers to the thick strata above the coal seam or thin immediate roof. It is strong with poor joint development. After mining, instead of immediate caving, it will overhang for a large area in the gob, resulting in high stress in front of the face and difficulty in gas dispersion. As a result, the face spalls, the roof exposes and the gas accumulates in the gob. With the continuing advance of the face and increase in area of overhang, the stress in the hard roof will eventually exceed its ultimate strength and cause a large area of caving, followed by quick release of energy concentrated in the roof and coal seam, which may cause rock bursts and other dynamic disasters in the mine as well as serious equipment damage and casualties. Therefore, the hard roof becomes one of the main factors causing rock bursts at the face.Hard roofs in China varies in conditions. It ranges from dozens of meters to hundreds of meters in thickness. However, coal reserve under hard roofs accounts for about 1/3 of the total reserve; moreover, nearly 40% of the fully-mechanized coal mining panels are those with hard roofs and more than 50% of the mining areas are associated with problems of hard roofs. Aiming at this problem, researchers at home and abroad have proposed many solutions, e.g. coal pillar support, strength weakening and forced caving, to prevent rock bursts caused by hard roof. These solutions have been employed in some cases with good results. However, due to the variability in geological conditions of mining and hard roofs, the application of the above solutions is limited."

Jan 1, 2015

By C. Chongo, F. X. Paquot, C. Ngulube

"Over the last six years, the Kansanshi copper/gold mine has continued to process significant quantities of complex transitional mixed ores. The effect of the complex mineralogy on the flotation performance is depicted. Initially, ore treated came predominantly from accumulated stockpiles. In the ensuing years, ore treated shifted to primarily freshly mined ore that generally showed less tarnish with better float kinetics but with the downside of producing lower concentrate grades. A number of changes were made to improve the efficiency of the roughing circuit and quality of concentrate produced. These changes were as a result of initial mineralogical studies and laboratory float test work done and discussed at length in a previous paper. Salient among the adopted recommendations from previous work were increasing circuit capacity and modifying configuration to increase the residence time and the number of sulphidisation stages. These modifications were completed and commissioned in 2011. This, however, resulted in significantly low rougher concentrate grades and subsequently below-specification final concentrate product. This was primarily due to higher mass pulls resulting from the extended rougher bank with multiple concentrate discharge streams. This necessitated the need for an enlarged cleaning capability to offset this. The extra cleaning capacity came on-stream in 2014. Of note was the development of a recovery model, based on the strong correlation between the total copper and acid-soluble copper ratio, as a tool for monitoring plant performance. INTRODUCTION The Kansanshi mine, the largest copper mine in Africa, is 80% owned by Kansanshi Mining PLC, a First Quantum subsidiary. The remaining 20% is owned by the state through the parastatal ZCCM. The mine is located approximately 10 km north of the town of Solwezi and 180 km to the northwest of the Copperbelt town of Chingola. The mine has been in commercial operation since 2005. Prior to June 2009, Kansanshi mine treated only two ore types: oxide and sulphide. All transitional ores mined during the period leading up to 2009 were stockpiled. The treatment of the minerologically complex, transitional ores through a third train commenced in June 2009 but with numerous metallurgical challenges. This transitional ore (called mixed ores) could not be previously treated economically due to high gangue acid consumption (GAC) minerals association (making it unsuitable for the oxide float–leach circuit) and poor flotation response ruling out the conventional sulphide float circuit. The new novel circuit involved a conventional sulphide pre-float followed by flotation involving staged controlled potential sulphidisation (CPS)."

Jan 1, 2015

By M. L. F. Paullo, S. Cristian Mejia, D. Roehl

"Rock fracture simulation most often presents non-linear behaviour due to loss of material integrity and strain concentration in the fracture zone. These strains generate local instabilities that propagate to the global system of equilibrium equations, generating convergence problems of the numerical solution. Often, in such cases, analyses in the post-critical regime are unfeasible. To overcome the numerical difficulties associated with problems of stiffness loss in the post-critical regime control methods, also called continuation methods, are employed. Among them are the arc-length method, the energy control method and the indirect displacement control method. These methods are employed in conjunction with a Newton- Raphson scheme for the solution of non-linear systems of equations. However, depending on the system instability, convergence in not guaranteed even with very small increments. In the present work these control techniques are investigated in combination with cohesive elements to simulate rock fracture. The constitutive model employed with the cohesive elements represents stiffness degradation through a damage law, which leads to serious convergence difficulties as reported in the literature. Here the continuation methods mentioned are applied to a Mode I rock fracture problem and to hydraulic fracture simulations. The effectiveness of the different continuation methods is compared.INTRODUCTIONThe process of rock fracture induced by the fluid pressure is called hydraulic fracturing. The propagation of a hydraulic fracture is a complex process, which is basically defined by the mechanical deformation of the rock, the fluid flow within the fracture and the fracture propagation itself (Mokryakov, 2011). In the works of Bendezu et al. (2013), Chen (2012) and Carrier et al. (2012), vertical hydraulic fracture propagation is modeled by cohesive elements with traction-separation law. The softening behavior of rock in post-critical regime is demonstrated by experimental testing and is characterized mainly by high strains and low stresses (Crowder and Bawden, 2004). This nonlinear behaviour can arise due to material nonlinearity, such as micro-cracking and damage, leading to softening behaviour (Chandrakant, S.D., 2012). The cohesive fracture model considers in its formulation the softening behaviour that most rocks present in post-critical regime with propagation criteria."

Jan 1, 2015

By David W. Martel, Tom George

"As part of the regional water authority review and upgrade of local dams a 35m x 5m x 3m wet soil mixed block was required for stabilisation of a dam wall toe in remote Victoria, Australia. Remote access, extremely poor roads and high mobilisation costs made more traditional CSM and deep mixing methods cost prohibitive. The dam required a redesign to raise the wall by 2.0m to increase water storage. Additionally, the dam required additional stabilisation to reduce the risk of liquefaction during an earthquake event. Soil testing indicated loose, cohesionless, high permeability soils to a depth of 3.0 to 3.5m across the toe of the wall. This resulted in high dam seepage through the toe of dam wall potentially causing the factor of safety during a seismic event to decrease to a dangerous level. A number of laboratory trials were completed to determine the mix ratio of cement required to improve the strength of the saturated, liquefiable soil.Wagstaff Piling was responsible for achieving the required soil/cement strength and mix depth on site. As the ground conditions were too soft for conventional soil mixing equipment, an excavator mounted Mitsui road header was modified to fit a 20 tonne excavator. A purpose built remote batching plant was set up on more stable ground approximately 200m from the wall and utilised for preparation of cement and water slurry for supply to the machine. As the ground was too soft to support the excavator, the progressively improved ground was used as the working platform. Both wet grab sampling and in situ testing was undertaken to determine the UCS of the improved soil. These results indicated several variations in the results due to size effects.1 INTRODUCTIONA small town in remote Victoria relies totally on its water supply from a small dam. The dam wall required stabilisation works by ground improvement as studies completed on the dam classified it as a high risk of failure under an earthquake event. In addition, the earth fill dam had high levels of seepage and poor control measures, requiring the dam to be upgraded to comply with all regulations.The relevant water authority engaged a contractor under a design and construct contract to complete the works. Wagstaff Piling was engaged as the Subcontractor to provide design and construction advice including the contract for the ground improvement works. Initial discussions involved CSM walls, cut-off walls and mass soil mixing solutions. However, due to the access restrictions for piling equipment, mass soiling mixing was the chosen method of ground improvement."

Jan 1, 2015

By M. Hozayen, E. S. Radwan, P. A. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests are summarized in this paper whereas wellbore stability analysis and formulation of a 3D geomechanical model that was built for that purpose is summarized in a sister paper (Part II).A suite of tests reported includes tensile strength, uniaxial and triaxial compression and permeability under stress at simulated reservoir conditions. All tested rocks have been grouped into twelve test units and reservoir geology, rock types and challenges related to designing a viable sampling and testing program for a big reservoir are discussed first followed by sample selection criteria and details of the testing program. All test units showed brittle behavior at zero confinement and some samples showed similar behavior at low confining stresses. With confining stress increase, the behavior gradually turned to plastic but some samples showed features of ductile behavior even at low confinement.Obtained experimental data have been summarized in the form of strength criteria and correlations. The Mohr-Coulomb strength equations were obtained for each test unit and also for the averaged values. It was noticed that triaxial compressive strength (TCS) increases with decreasing porosity or increasing density but their influence on TCS is getting smaller with confining pressure increase. Good correlation of porosity and density with Young’s modulus, Poisson’s ratio, unconfined compressive strength (UCS), friction angle, cohesion and tensile strength has been noticed and there was an increasing trend between the confining pressure and TCS. Rock type (mud or grain supported) was not influencing the TCS as much as porosity and density and the two lithologies encountered affected TCS approximately in the same way. These results and correlations are summarized and explained in this paper. They were further used in the numerical modelling part (Part II) of this paper, Hozayen et al. (2015). It is also concluded that rock lithology is not a decisive factor and mechanical properties of tested rocks should be rather considered dependent on porosity and permeability. This helped greatly in reducing the number of tests that had to be performed."

Jan 1, 2015

By M. S. Celik, H. Du, J. D. Miller, F. Cheng, O. Ozdemir

"In this paper, recent progress with respect to the flotation chemistry of soluble salt minerals is reviewed, and some of the more relevant issues including the hydration states of ions, the interfacial phenomena of salt surfaces and the flotation behavior of selected soluble salts are discussed. Due to the high solubility, the flotation of most soluble salts has to be carried out in their saturated brines. Anecdotal evidence has suggested that the hydration states of the ions have significant influence on the physicochemical properties of the solutions, the surface charge and wetting characteristics of the minerals, the collector adsorption states and, further, the flotation behavior of the soluble salts. In this regard, reviewing past research findings, efforts are made to establish a correlation between the ion hydration states with the flotation behavior of the soluble salts. Further, advances in understanding the significance of colloid adsorption involved in the soluble salt flotation process are addressed, and future research efforts to understand the soluble salt flotation chemistry are suggested.IntroductionSoluble salt minerals are essential raw materials for the production of a variety of commodities, fertilizers, potassium hydroxide, soda ash, magnesium compounds and other chemicals. These soluble mineral resources can be processed using flotation technology and, currently, more than 80% percent of the world’s potash is produced by the selective flotation of KCl crystals (sylvite) from other salt crystals, predominately NaCl (halite) and other more complex salts (Searls, 1990). Despite the successful application of flotation technology in the potash industry, the mechanisms for collector adsorption on soluble salts have not yet been fully understood and, therefore, have been of considerable interest to flotation researchers for many decades."

Jan 1, 2015

By F. Hassani, J. Peck, D. J. Lucifora

The performance of a rotary blasthole drill is heavily dependent on the material being drilled. This material is a microcosm of the in-situ geology that makes up the surface mine in which the rotary blasthole drill is deployed. The performance metrics that are influenced by the in-situ geology are penetration rate (distance drilled per unit time), rotary torque and to a lesser extent rotary speed and vibration. For simulation and testing purposes it is useful to have a validated plant model based upon the application of study. Once validated, a plant model can be used to perform simulation based testing as a supplement and possibly in place of more expensive and logistically complex field testing. Previous studies in the field of rock mechanics have supplied proven models that relate the performance of a rotary blasthole drill to the material being drilled for a given rock type with a given drill bit. In this study, field based experiments were conducted in an active surface mine on a working rotary blasthole drill and the corresponding monitoring while drilling (MWD) data was recorded. Data analysis was then performed on the collected field data. The techniques used successfully fit the collected MWD data to the previously proven rock mechanic models. This paper explores the theory relating rotary blasthole drill performance to the material being drilled, illustrates the required data collection and data analysis techniques, and demonstrates the ability of these techniques and the known rock mechanic models to provide a simulated plant model for the drilling process that can then be validated. This validation is also discussed.

Jan 1, 2015

By S. Pietruszczak, G. Su, T. S. Nguyen, E. Haghighat

"In this paper, the mechanical properties of Tournemire argillite are modeled using a mathematical framework which employs the microstructure tensor approach (Pietruszczak & Mroz, 2000). The experimental data incorporates the results of a series of triaxial tests (Abdi & Evgin, 2013) conducted at different orientation of bedding planes relative to the direction of loading. First, a plasticity framework is presented which involves the specification of the conditions at failure as well as the description of the irreversible deformation process. Later, a systematic procedure is outlined for identification of material functions/parameters involved. The paper is concluded by presenting the results of numerical simulations of the triaxial tests. It is demonstrated that the model can adequately reproduce the primary effects of anisotropy in the stable deformation regime as well as the onset of fracture.INTRODUCTIONThe understanding of the mechanical behaviour of argillaceous rocks is important in many types of geotechnical projects, including petroleum extraction, carbon dioxide sequestration as well as deep geological disposal of radioactive waste. In all these cases, the primary concern is the onset and propagation of damage due to excavation, transport of pore fluids and/or elevated temperature. The Canadian Nuclear Safety Commission (CNSC), Canada’s nuclear regulator, will be responsible for the licensing of future deep geological repositories. In order to evaluate the safety of deep geological repositories, CNSC staff keep abreast of scientific developments by collaborating with national and international partners on experimental and theoretical research on the long-term performance of those engineered and natural barriers. Through that collaboration, the CNSC has access to data resulting from experiments performed at different Underground Research Laboratories (URL). Such an URL is situated in Tournemire, France, in an argillaceous rock formation, the Tournemire argillite. The Tournemire argillite is characterized by the presence of closely spaced bedding planes and exhibits a strong anisotropic behaviour, so that its strength as well as deformation properties are directionally dependent."

Jan 1, 2015

By H. Jang, Y. Kawamura

Unplanned dilution and ore loss directly influence not only the productivity of underground stopes, but also the profitability of the entire mining process. Stope dilution is a result of complex interactions between a number of factors, and cannot be predicted prior to mining. In this study, unplanned dilution and ore loss prediction models were established using multiple linear and nonlinear regression analysis (MLRA and MNRA), as well as an artificial neural network (ANN) method based on 1067 datasets with ten causative factors from three underground longhole stoping mines in Western Australia. Models were established for individual mines, as well as a general model that includes all of the mine data-sets. The correlation coefficient (R) was used to evaluate the methods, and the values for MLRA, MNRA, and ANN compared with the general model were 0.419, 0.438, and 0.719, respectively. Considering that the current unplanned dilution and ore loss prediction for the mines investigated yielded an R of 0.088, the ANN model results are noteworthy. The proposed ANN model can be used directly as a practical tool to predict unplanned dilution and ore loss in mines, which will not only enhance productivity, but will also be beneficial for stope planning and design.

Jan 1, 2015

By L. Yuan, J. Qin, J. Xie, Q. D. Qu, Y. P. Liang

"This paper presents key outcomes of a major Asia-Pacific Partnership project between the Commonwealth Scientific and Industrial Research Organisation and Huainan Mining Industry Group Co. Ltd. to develop and demonstrate advanced technologies at Pansan mine, Huainan, China. A comprehensive approach assessed fundamental strata and coal seam methane conditions during mining and optimized mining sequences and coal mine methane capture systems. The project demonstrated a practical approach and procedures for advanced coal and methane co-extraction systems, improved mining safety and efficiency, increased methane capture and use, and reduced fugitive methane emissions.RÉSUMÉ Le présent article donne les principaux résultats d’un grand projet de partenariat Asie- Pacifique entre le CSIRO (Commonwealth Scientific and Industrial Research Organisation) [Organisation de recherche scientifique et industrielle du Commonwealth australien] et le Huainan Mining Industry Group Co. Ltd.; ce projet cherche à développer et à démontrer des technologies avancées à la mine Pansan, à Huainan, en Chine. Une perspective globale a évalué les conditions fondamentales des strates et du méthane dans les couches de charbon durant l’exploitation et a optimisé les séquences d’extraction et les systèmes de captage du méthane dans les mines de charbon. Le projet a permis de démontrer une approche pratique et des procédures pour des systèmes avancés d’extraction conjointe du charbon et du méthane, pour améliorer la sécurité et l’efficacité minières, accroître le captage et l’utilisation du méthane et réduire les émissions fugitives de méthane."

Jan 1, 2015