Search Documents

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By Zach Ellis, Dusty Fisher

Lightning is a major concern in the explosives industry. The enormous amount of energy delivered to the Earth from a single bolt of lightning is more than capable of detonating explosives. Although explosives incidents caused by lightning strikes are rare, lightning is of great concern to blasting professionals who spend many hours working on or near loaded blast patterns.

Jan 1, 2015

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

By Matthew K. Coy, Paul N. Worsey

The work described in this paper comprised the master’s thesis work of the primary author and was conducted at the Missouri S&T experimental mine. The objective was to determine if rubber tractor treads could be used as an alternative material for blasting mats. These treads are made from steel cable and vulcanized rubber and are very tough. However, once they reach the end of their life on mobile equipment, they are destined for a landfill, or dump site, because they are too tough to recycle. A potential alternative use for them is as blasting mats. Several discarded treads were obtained from Kolb Grading in St. Louis.

Jan 1, 2015

By D. Fenn, A. du Kanda, D. Dukhan

"SynopsisGibb Consulting Services was contracted by Eskom Line Engineering Services to conduct an investigation to determine the absolute displacement to date and infer the current rate of displacement of unsurveyed colliery backfill.At the test site, where a 400 kV power line is to be constructed, neither the surface nor the backfill material had been monitored and it was not possible to state whether the surface will be subject to future settlement that may compromise surface infrastructure. Therefore indirect methods of estimating current and future displacements needed to be found to act as a proxy for a comprehensive long-term settlement monitoring exercise and provide a reasonable estimate for the settlement that has occurred in the decades of mining.The innovative solution was to recover essentially undisturbed core from backfill using a sonic drill rig and use the measured dry density values from the samples as a proxy for the rate and absolute displacement in the backfill.The success in obtaining an essentially undisturbed backfill core and the clear relationship of the backfill density with age and depth allowed the conclusion to be issued that the power line infrastructure can be constructed over the backfill; with a warning that once the water table recovers after mining ceases some collapse settlement may occur.With this method, the amount of settlement can be predicted and, if proven conclusively, provides a way to confidently release huge areas of currently waste ground for future surface infrastructural development.IntroductionIn coal mining, it is normal mining practice to backfill the newly mined-out voids with the excavated waste rock and soils. As there is no requirement for the mining companies to uniformly compact the spoil or accurately monitor surface or inter-backfill displacement, these backfilled voids are prone to differential compaction and consolidation settlement. They are therefore avoided as sites for future surface infrastructure work, especially for linear structures such as roads, railways, and power lines."

Jan 1, 2015

By Q. Cheng

This paper introduces the multi fractal interpolation method (MIM)developed for handling singularities in data analysis and for data interpolation. The MIM is a new moving average model for spatial mapping and interpolation. The model decomposes the raw data into two components: singular and nonsingular components. The former can be characterized by a localized singularity index that quantifies the scaling invariance property of measures from a multifractal point of view. The latter is a smooth component that can be estimated using ordinary kriging or other moving average models. The local singularity index characterizes the concave/convex properties of the neighbourhood values. The paper utilizes a binomial multiplicative cascade model todemonstrate the generation of one- and two-dimensional data with multi-scale singularities which can be modelled by asymmetrical multifractal distribution. It then introduces a generalized moving average mathematical model for analysing and interpolating data with singularities. Finally, it is demonstrated by a one-dimensional case study of de Wijs’ data from a profile in a zinc mine, that incorporation of spatial association and singularity can improve the interpolation result, especially for observed values with significant singularities.

Jan 1, 2015

By R. L. Keiski, H. Miettunen

"The serpentinite massifs of Hitura are located in the municipality of Nivala in Central Finland. The most important sulfide minerals in the ore are pentlandite, pyrrhotite and chalcopyrite. The ore body consists of amphibolite rocks in contact with serpentinite against mica gneiss. The mean Ni grade of the ore is about 0.7%, and the highest Ni grades have been encountered in close contact. In general, the inner parts of the ore are strongly serpentinized ultramafite and some sulfides have been converted to mackinawite and valleriite. The degree of alteration varies considerably within the ore body and, correspondingly, the grain size of the sulfides varies as well. In this study, flotation tests were done with samples from different zones of the ore body. The flotation test results on the bench scale and plant scale are discussed in terms of the mineralogical features of the ore. Ores in the North Hitura zone differ from those in the South Hitura zone.IntroductionThe Hitura nickel mine, like the entire Nivala area, is part of the Bothnian Svecokarelian schist zone, where numerous Ni-Cu boulders have been discovered since the early 1930s. The Nivala area has therefore been the subject of exploration activities by the Geological Survey of Finland (GSF) and mining companies. The first period of exploration started in 1936, and the Makola nickel deposit, located 3 km south of the Hitura mine, was discovered by GSF in 1937. About 415,000 tonnes of ore were mined at Makola between 1941 and 1954. In 1937, during the exploration and development stage of the Makola mine, boulder tracing and a geophysical survey revealed a significant ultramafic body with some lowgrade Ni-Cu occurrences in the South Hitura zone.In 1961, GSF continued the exploration program in the area and discovered the North Hitura ultramafic complex and its allied Ni-Cu occurrences. In 1964, Outokumpu Oy bought the property and, after underground exploration, comprehensive mineralogical studies, process research and a feasibility study, production started in 1970 (Isohanni et al., 1985)."

Jan 1, 2015

By Dezhong Kong, Jaichen Wang, Shengli Yang

"The stability control of longwall coal face is the key technology of large-cutting-height mining method. Therefore, a systematic study of the factors that affect coal face stability and its control technology is required in the development of large-cutting-height mining method in China. After the practical field observation and years of study, it was found that the more than 95% of failure in coal face are shear failure. The shear failure analysis model of coal face has been established, that can perform systematic study among factors such as mining height, coal mass strength, roof load, support resistance, and face flipper protecting plate horizontal force. Meanwhile, sensitivity analysis of factors influencing coal face stability showed that improving support capacity, cohesion of coal mass and decreasing roof load of coal face are the key to improve coal face stability. Numerical simulation of the factors affecting coal face stability has been performed using UDEC software and the results are consistent with the theoretical analysis. The coal face reinforcement technology of largecutting- height mining method using the grouting combined with coir rope is presented. Laboratory tests have been carried out to verify its reinforcement effect and practical application has been implemented in several coal mines with good results. It has now become the main technology to reduce longwall coal face failure of large-cutting-height mining method.INTRODUCTIONLarge-cutting-height mining method of more than 3.5m mining height, is one of the main methods for thick-seam mining in China. Currently, the largest mining height is 7.3m and the support capacity is 1,800mt. Shendong and Jincheng mining area have the best use of large-cutting-height mining technology (Wang, 2009). Generally, the mining height ranges from 6.5m to 7m and the support capacity ranges from 1,000mt to 2,000mt, annual output of the panel is between 10 and 12 million tons and the highest are 15 million tons. The main goal of large-cutting-height mining technology is to achieve high yield and high efficiency by increasing the advancing speed of longwall face (Yuan, 2011- 2012). However, in certain geologic conditions, rib spalling and roof falls in the unsupported area often occur. Because of the large tonnage of large-cutting-height mining equipment, once the rib spalling and roof falls cause the equipment to be out of alignment, the face advancing speed could be affected seriously that in turn affects the output (Yang, 2012). Therefore, studying the failure mechanism and control technique of coal face in large-cuttingheight mining method is of great significance."

Jan 1, 2015

By J. Ambrose, R. W. Zimmerman

"Shales are highly anisotropic in their mechanical behavior. The strength ( ??1) of anisotropic shales depends not only on the magnitude of the other two principal stresses ( ??2, ??3), but also on the bedding plane orientations (?) relative to the principal stresses. In this study, the role of the intermediate stress ( ??2) on the strength of shale is evaluated using new data from triaxial compression and extension tests. To understand the failure behavior of shales, we have carried out triaxial compression tests ( ??1 > ??2 = ??3) on two organic rich mudstones, at different confining stresses and loading angles. We first fit the triaxial compression data with Jaeger’s plane-of-weakness model, and find that the model is able to represent the strength behavior of anisotropic shales reasonably well. We then carried out five triaxial extension tests ( ??1 = ??2 > ??3) for a high strength-anisotropy shale, and two extension tests for a low strength-anisotropy shale. Results from the compression and extension tests for failure along the weak plane shows that the role of ??2 is not significant for weak plane failure. However, for the low strength-anisotropy shale, the failure strength of the intact rock (i.e., at ??= 0o and 90o) for compression and extension tests were significantly different. This indicates that for intact rock failure, the role of ??2 is important and cannot be ignored.INTRODUCTIONFor many years, various researchers have studied the roles of ??2 for failure of isotropic rocks. (Mogi, 1967 and 2007; Colmenares and Zoback, 2002; Al-Ajmi and Zimmerman, 2005 and 2006; Haimson, 2009; Ma and Haimson, 2012). The findings from these studies show that the effect of ??2 on the strength of isotropic rocks is generally significant, and cannot be ignored.Since the role of ??2 in the failure of isotropic rocks was recognized, other researchers attempted to extend some of these isotropic failure criteria to anisotropic rocks, but with limited success (e.g., Tiwari & Rao, 2007; Singh et al., 1998; Zhang and Zhu, 2007; Pei, 2008). Smith and Cheatham (1980), on the other hand, conducted true-triaxial experiments on the Green River Shale and used a J2-I1 type relationship to predict the strength behavior, but without considering the effect of the three-dimensional orientation of the weak plane on strength. Therefore, unlike for the case of isotropic rocks, additional studies need to be done to determine the role of 2 on the failure of anisotropic rocks."

Jan 1, 2015

By S. Hon, C. Searcy, R. DasGupta, B. Fleet, A. Davidse, A. Pringle

"The mining industry is facing serious long- and short-term challenges relating to uncertain commodity prices, environmental pressures, and margin compression due to rising energy costs. Energy issues, formerly treated as an operating cost, are changing as executives search for longer term solutions to deal with uncertain fossil fuel prices and greenhouse gas emissions. Consequently, mining executives are increasingly willing to consider introducing a proportion of renewable energy (RE) systems into the mine energy mix. This paper examines how RE can be successfully integrated at mine sites, as well as some of the benefits and barriers to their wider adoption.RÉSUMÉ L’industrie minière fait face à de sérieux défis, à long et à court terme, en raison de l’incertitude des prix des matières premières, des pressions environnementales et des compressions de la marge bénéficiaire dues à la hausse des coûts de l’énergie. Les questions énergétiques, auparavant considérées comme un coût d’exploitation, changent alors que les cadres cherchent des solutions à plus long terme afin de prendre des mesures pour contrer les prix incertains des combustibles fossiles et les émissions des gaz à effet de serre. C’est pourquoi les cadres miniers sont de plus en plus disposés à considérer l’introduction d’une proportion de systèmes d’énergie renouvelable dans l’équation énergétique de la mine. Le présent article traite de la manière dont les énergies renouvelables peuvent être introduites avec succès aux sites miniers ainsi que quelques-uns des avantages et des barrières à leur application à une plus grande échelle."

Jan 1, 2015

By S. Bentley

"Everyone has a general idea what mixing means, but describing the mixing process is not so simple. The objective of any mixing process is to distribute and blend the materials with different characteristics, different quantities as evenly as possible resulting in a homogenous mixture. Introducing proportional movement with the optimal intensity into the materials achieves effective homogeneous mixing results. A simple one directional movement with inadequate acceleration of the materials would obviously not achieve the same mixing results. This would be more like stirring than mixing. The amount of relative movement that is introduced is a decisive factor. Circumstances for successful mixing involve distribution of all materials, and achieving the highest probability that all recipe particles located in a specific position at the beginning can be found at any random location in the mixing chamber at the end of the process. This is the only way to ensure that a consistent result is achieved every time mixing is repeated.THREE-PART CYCLE The mixing cycle occurs in three phases; charging the mixer, the mixing process, and discharging. The sequence in which the individual materials to be mixed are filled into the mixer can have a huge impact on the efficiency of the mixing cycle. The mixing cycle overlaps the charging process and the discharge cycle follows the mixing cycle. To achieve optimum results, effective discharging methods should be taken into consideration to avoid risks of segregation. Costs for energy and wear should be as low as possible and finally, it is very important that the mixing cycle takes place as quickly as possible. In concrete or paste backfill production, selecting the best mixing technology is crucial for both the quality of the final product to be blended and the efficiency of the production process. The optimum mixing system is one that rapidly disperses all ingredients evenly throughout the mixing trough and completely surrounds all the course or fine aggregate particles with the slurry cement particles. Specific for paste production it’s the mixers job to also break-down unconditioned tailings to achieve consistent paste viscosity or measured spread. Many paste and concrete formulas also involve small quantities of chemical additives which also must be evenly distributed effectively. The time required per mixing cycle as well as the costs of energy, wear and maintenance will determine the economy of the concrete production."

Jan 1, 2015

By G. F. Liu, S. Owada

Platinum Group Metals (PGMs), Pt, Pd, Rh, have been widely used as a three-way catalyst to clean discharged gas from automobiles and therefore a considerable amount of the spent catalysts is generated annually. This paper proposes a novel concentration technology of PGMs by utilizing the double-deck structure of PGM bearing alumina-ceria and cordierite phases. The applied technologies are a combination of heating-quenching, selective grinding and screening for separating alumina-ceria phase from cordierite. Temperature change as a function of quenching time and the thermal stresses applied to both phases were simulated and calculated by FEM, and it was clarified the mechanism of micro-cracks generation at the phase boundary and micro-cracks in alumina-ceria phase, which indicated that separation of alumina-ceria phase from cordierite and selective breakage of alumina-ceria phase could be achieved in the subsequent selective grinding with an attritor. This process could concentrate 46 wt% of alumina-ceria phase into fine fractions with 86 % recovery efficiency. The remaining alumina-ceria phase can be further recovered by applying flotation and so on.

Jan 1, 2015

By J. Duriez, L. Scholtès, F. V. Donzé

"Fracture propagation process in brittle rock is investigated by means of numerical simulations performed with an adapted formulation of the discrete element method. The progressive failure mechanism is simulated through the breaking of the bonds making up the cohesion between the elements constituting the simulated medium. The use of appropriate contact laws associated to a near neighbor interaction feature provide the model the ability to reproduce fundamental characteristics of brittle rock behavior such as, for example, high values of the tensile to compressive strength ratio. Great attention is given to accurately describe the properties of the pre-existing joints or faults in the model. A specific joint model gives the possibility to define a tailor-made behavior of the discontinuity surfaces without suffering from discretization bias.Compression test simulations are performed on pre-flawed samples and compared to experimental results in order to validate the numerical approach for describing the initiation and propagation of fractures in brittle rock under mode I+II loading. It is shown that the crack mechanical parameters can greatly influence the fracturing pattern, in particular its frictional properties. Overall, the numerical simulations reproduce fairly well the failure patterns that are obtained experimentally.The discrete model is then used to study mode I+III loading to give an insight into fracturing problems occurring at the scale of the continental crust. The ability of the model to support mechanically the physical modelings performed with wet clay or sandbox is shown. As an example, the model is used to track the development of a twist crack system (wrench fault) through the nucleation and coalescence of microcracks."

Jan 1, 2015

By P. G. Martin

"As the speed of business has continued to increase over the last decade, the focus on real-time control of the performance of both stationary and mobile assets has become an increasing priority. Traditionally the maintenance team has been focused on the management of the availability of assets while the operations team has been focused on the throughput of those same assets. Typically operations and maintenance teams worked almost independently in spite of the fact that they were both working with the same assets. Part of the problem has been their traditional performance measures which have often been diametrically opposed. Recent advancements in the area of real-time performance measures and decision support have helped to drive higher levels of collaboration between operations and maintenance leading to real-time asset performance control and higher levels of business performance. This paper will explore the forces driving the need for changes, present an effective approach to the definition of the most appropriate business performance measures, and examine the effectiveness of contextualized real-time decision support resulting in asset performance control. TRADITIONAL APPROACHES TO ASSET PERFORMANCE MANAGEMENT In most industrial operations the phrase asset performance management is synonymous with maintenance of the industrial assets. This is the way industry has viewed asset management and asset performance management for decades. This is a very limited perspective that is serving to constrain the profitability of industrial operations. As industrial organizations began to form following the Industrial Revolution, the complexity of the operations forced an organizational design based on specialization. No single person could understand all of the aspects of an industrialized operation. This was particularly true at the plant floor level where the operation and maintenance of the industrial equipment required very different skillsets and training. To accommodate the vast differences most industrial organizations set up operations teams to run the equipment and maintenance teams to keep the equipment available to the operation. Both teams were dealing with the same industrial equipment but from very different perspectives and with very different performance measures. Typically the operations team was measured on maximizing the output of the equipment – or throughput. On the other hand the maintenance team was measured on the uptime – or availability of the equipment."

Jan 1, 2015

By P. Zhang, W. D. Xiao

"A process mineralogy study was conducted to guide the development of a process for the extraction of vanadic oxide (V2O5) and aluminum compounds from bone coal and its ash as well as the production of byproducts. Results show that to extract the targeted metals at higher recovery rates, one must find a suitable agent capable of destroying the structure of the mica and breaking down the lattices in which these metal-bearing minerals occur. For such minerals, metal extraction efficiency is usually low if the approach is simply adding an oxidant that cannot destroy the structure. In this research, a byproduct fluosilicic acid (H2SiF6) at 20 percent concentration from an operating phosphate fertilizer plant was found to be powerful and effective for the leaching of vanadium-bearing minerals such as mica. This environmentally friendly process improved the leachability of valuable constituents in the bone coal significantly, with the leaching rate of V2O5 increased to 94 percent, from 83 percent, and that of aluminum oxide (Al2O3) increased to 75 percent, from 40 percent. X-ray diffraction and chemical analyses showed that the structure of mica can be destroyed using fluosilicic acid either alone or in combination with sulfuric acid. Based on the process mineralogy study, a processing flowsheet was tested, which resulted in a final V2O5 powder product with purity of 99.2 percent and an overall recovery rate of higher than 85 percent. The flowsheet consists of leaching, ion exchange and ammonium precipitation. With this process, various byproducts could also be generated, including aluminum fluoride, cryolite, aluminum sulfate, calcium sulfate, ammonium chloride, sodium chloride and cement admixtures.IntroductionVanadium is an important rare metal broadly used in the production of steel alloys and nonferrous alloys as well as in the chemical field as a catalyst. Vanadium-bearing bone coal and clays are abundant in China, and they contain other valuable metals such as aluminum. Bone coal is a type of carbonaceous shale. The vanadium-bearing minerals mainly exist in mica, kaolin, iron oxides, tourmaline and garnet. According to previous studies (Xiao, 2007; Xu, 1989; Xu and Chen, 1991; Ji and Xu, 1991; Chen and Xu, 1992; Xu and Heng, 1992), vanadium occurs from the isomorphous substitution of V3+ for Al3+ or Fe3 + in the crystal lattices of mica, tourmaline, garnet, dolomite and aluminosilicate minerals. In iron oxide and kaolin minerals, vanadium appears as an adsorption form. The isomorphous substitution of vanadium is more stable in tourmaline, garnet and silicate minerals. Therefore, vanadium in bone coal may exist in three phases: vanadium-containing kaolin and oxides, vanadium-containing mica, and tourmaline and garnet (Xu and Chen, 1993; Xu and Zhang, 1993; Xu and Wang, 1994; Feng, et al., 2005; Lin and Fan, 2001)."

Jan 1, 2015

By Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"Load transfer distance (LTD) is simple in concept and usually evident in underground coal mines. Many people in the mining industry recognize LTD as the distance from the panel to where the mine ribs and pillars show evidence of renewed spalling, floor heave, or other effects of increased weight due to longwall mining or pillaring. Barrier pillars, in particular, are designed to shield mains and other relatively permanent facilities from this loading. LTD is also important in determining the extent and degree to which mining increases the load on pillars and ribs in the gate roads. Generally, a long LTD reduces loads in gate roads, but may require larger barrier pillar widths to protect mains or adjacent panels from excessive loads. Therefore, a long LTD may make it easy or difficult to meet various objectives of mine layout design . LTD reflects overburden geology in two ways: First, overburden that is weak and readily caves will limit both the amount and distance of load transfer. Second, stronger, stiffer, sandier, and more massive overburden increases both the amount and distance of load transfer. As such, LTD is central to coal mine layout design and calibration of numerical models that seek to anticipate these transfers of load during mining. However, the term does not have a consistent definition in the literature, and various instruments and observational techniques with varying sensitivities and thresholds have been used to indicate the onset of mining-induced stress increase and, subsequently, to determine an LTD. Consistency is important for meaningful comparison of ground response between mining sites and for accurate calibration of models.This paper adds to the body of observed and reported LTDs by presenting cases with relatively sandy and massive overburden at two western coal mines. These two cases include observation and measurement of LTD with multiple methods and provide insight into how distances reported relative to different criteria and instrumentation could be adjusted for comparison against a common base. This base is the criteria used by Peng and Chiang (1984) to determine their empirical equation. In one of these two cases, LTD was recently measured at a western U.S. coal mine (Mine A) to be approximately four times that calculated using the Peng and Chiang empirical equation. LTD measurements were examined using various instruments at Mine A and at adjacent Mine B. The measurements at Mine B showed that LTD was significantly greater than that calculated by the Peng and Chiang equation. Difficulties with BPC installation and fittings at Mine B permitted only ranges of LTD to be determined from some BPCs. Even so, the LTDs and ranges of LTDs determined were consistent with the LTDs determined at Mine A."

Jan 1, 2015

By R. Woods

"Comments on the paper ""Formation of hydrogen peroxide by chalcopyrite and its influence on flotation,""by A. Javadi Nooshabadi and K. Hanumantha Rao (Minerals & Metallurgical Processing, 2013, Vol. 30,No. 4, pp. 212-219)The formation of hydrogen peroxide from water during the grinding of chalcopyrite in a nitrogen-sparged environment, as reported by Javadi Nooshabadi and Rao (Minerals & Metallurgical Processing, 2013, Vol. 30, No. 4, pp. 212-219), is questioned on the grounds that oxidation of water by the mineral is unlikely to be thermodynamically feasible. It is argued that it is more likely that any peroxide that had been formed would have been generated from residual oxygen in the nitrogen-flushed system than from the oxidation of water.The formation of hydrogen peroxide by finely divided pyrite had been reported by a number of authors (Borda et al., 2001; Borda et al., 2003; Cohn et al., 2006; Schoonen et al., 2006; Schoonen et al., 2010; Jones et al., 2011; Javadi Nooshabadi et al., 2013). That hydrogen peroxide is formed in the presence of oxygen in solution can be comprehended from wellestablished mechanisms. Pyrite in aerated solution is known to oxidize by an anodic process that is coupled with the cathodic reduction of oxygen (Holmes and Crundwell, 2000). The latter process has been shown to occur through the formation of hydrogen peroxide (Biegler et al., 1975; Ahlberg and Broo, 1996). The pH dependence of cathodic oxygen reduction at other sulfide minerals, including chalcopyrite (Biegler et al., 1977; Rand, 1977), implies a similar mechanism at these surfaces."

Jan 1, 2015

"As part of a series describing the nickel operations of Vale Canada (formerly known as Inco), this paper focuses on the 1973 to current operations of the Copper Cliff nickel refinery in Ontario, Canada. The process used there employs the formation of Ni tetracarbonyl at high CO (gas) pressure and its subsequent decomposition at somewhat elevated temperatures to produce highly pure Ni pellets and powders. Personal sampling of workplace aerosol dusts is reported, with information on specific Ni compounds in the aerosols.RÉSUMÉ Dans le cadre de la série d’articles décrivant les opérations de nickel chez Vale Canada (anciennement Inco), le présent article cible les opérations de 1973 à ce jour à l’affinerie de nickel de Copper Cliff en Ontario, Canada. Le procédé utilisé à cette usine est la formation de tétracarbonylnickel sous une pression élevée de CO (gaz) et sa décomposition subséquente à des températures plutôt élevées pour produire des granules et des poudres de Ni pur. Un échantillonnage par l’auteur des poussières en aérosol est présenté ainsi que de l’information sur les composés spécifiques de Ni dans les aérosols."

Jan 1, 2015

By M. Noppé

"Dilution in underground coal operations can be underestimated by up to five times during Feasibility Studies, with disastrous economic consequences. Every 1% of stone waste introduced can reduce an in situ specific energy of 11,000 BTU/lb (25 MJ/kg) by some 110 BTU/lb (0.25 MJ/kg) and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some AU$1 million per year.This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation. The dilution trends before and after introducing the recommended controls in a continuous miner/longwall mine are presented over an eight year period. The additional information from such a dilution monitoring program can also be used to control mining horizons and plan longwall extraction heights across the face proactively, on a short-term scale with resulting improvements in productivity. INTRODUCTION Grade control, as practiced on any mine, is concerned with predicting routine quality and tonnage values for short- to medium-term mining operations, and the reconciliation of these predictions against “actual” results. For a longwall mine supplying steam coal, such routine parameters may include the proximate analyses, specific energy (SE), abrasiveness and sulphur, as well as float and sink analyses if the coal is beneficiated. In addition, grade control is concerned with identifying the mineable horizon (or horizons) in a selective-mining operation, together with monitoring how well these horizons have been extracted or adhered to. Close-spaced surface drilling can be costly for any mining venture, particularly for longwall mines operating in the deeper seams. For this reason, much of the data for short-term grade control requirements are acquired during actual bord-and-pillar development. The underground data are derived from so-called “channel” samples. These samples are cut or chipped from the coal seam, perpendicular to the mining horizon, with dimensions suitable for obtaining sufficient “representative” sample for analyses. For a 2m thick mining horizon, a channel sample 300 mm wide and 50 mm deep over the thickness of the horizon would provide some 4.5 kg of sample, sufficient for most of the necessary tests. To allow the information to be computer recorded, additional information such as seam thickness, sample co-ordinates, and the elevation of the seam (or horizon) roof or floor, may be required."

Jan 1, 2015

By H. Wen, X. Zhai

"The Jurassic coal fields which lay in west China are the major energy base and contain half of coal resources in China. Due to the gather and degeneration rules, the spontaneous combustion characteristic of Jurassic coal is distinguished with permo-carboniferous coal, which needs to be studied deeply. Programmed heating experiments of five Jurassic coal samples and three permo-carboniferous coal samples from different primal coal fields in West China were conducted to identify the characteristic parameters in the low temperature stage of oxidation and spontaneous combustion. The experiments were carried out under non-isothermal heating conditions up to 180? at the heating rate of 0.33?/min in an air atmosphere. The result showed that oxygen consumption rate, CO gas production rate and heating intensity of all coal samples increased with the rising of the temperature, which of the Jurassic coal was higher than that of Permian-carboniferous coal. The C2H4 gas of Jurassic coal generated earlier, more than that of Permian-carboniferous coal in the process of oxidation and spontaneous combustion. It indicated that the Jurassic coal was easier to be oxidized and spontaneous combustion and the index parameters of spontaneous combustion were different between the Jurassic coal and permo-carboniferous coal.INTRODUCTION Coal was the foundation of industry development, and occupied 70% of primary energy production and consumption structure in China. According to the data of the 3rd coalfield prediction, 39.6% of the total coal resources were located in northwest Jurassic coal field in China [1], where the quality of coal was excellent. The study of northwest Jurassic coal already dated from the 80s of the 20th century, about coal rock composition, coal metamorphism [2], coal-derived hydrocarbons, coal structure [3], etc. The results of these studies showed that the composition and properties of Jurassic coal was obviously different from Permian-carboniferous coal, as well as the characteristic of spontaneous combustion [4]. As a result, the spontaneous combustion characteristic of Jurassic coal particularly needed to be studied. Now more and more methods could be conducted to test the characteristics of coal spontaneous combustion, for example, thermal analysis technology [5-7], programmed heating experiment [8-10] and coal spontaneous combustion experiment [11,12]. In these methods, programmed heating experiment could be conducted to determine the oxygen consumption rate, CO gas production rate and heating intensity quickly."

Jan 1, 2015