Search Documents

By Rajarshi Pramanik, Nirjhar Dhang, Dilip K. Baidya

"This paper performs the reliability evaluation of pile foundation under vertical loading condition using the concept of fuzzy set theory. The uncertain parameters are expressed as fuzzy numbers. Monte Carlo simulation technique in conjunction with fuzzy set theory and fuzzy reliability index approach are implemented in evaluation of the probability of failure of pile foundations. The results are validated through some well established methods such as, First Order Reliability Method (FORM), Second Order Reliability Method (SORM), and direct Monte Carlo Simulation (MCS). Response surface method (RSM) is used to approximate the original limit state equation through second order polynomial. The effect of the position of the water table is also highlighted. Finally, the effect of the variation of applied load is examined and it is observed that the fuzzy reliability analysis gives more conservative estimate of failure probability than the other methods.INTRODUCTIONCivil engineering structures, such as high rise buildings, bridges, offshore platforms etc. are always subjected to vertical as well as horizontal loads. To support these structures, pile foundations are generally the solution in most of the situation. It transmits load from the superstructure to soil at a reasonably great depth. This transfer may be by vertical distribution of the load along the pile shaft or a direct application of load to a lower stratum through the pile tip. Different methods are available to estimate the capacity of piles embedded in different types of soil and under the application of vertical and horizontal loading. To consider the variability in soil and other unforeseen able situation, generally a reasonable value of factor of safety is used to estimate the designed capacity of the pile. Recent developments have shown a trend to place the treatment of uncertainty on a more formal basis, in particular by applying the results of reliability theory to geotechnical engineering. Keeping in mind the importance of pile foundation in the engineering structures it is essential to maintain a high structural safety which result in increase in reliability. The probability theory has been proved to be a powerful tool for representing variability in mathematical models. The variability associated with soil parameters and the modeling uncertainties are needed to be considered for the reliability assessment purpose.Recent development (Zhang et al. 2005; Misra and Roberts 2006; Haldar and Babu 2008; Basu and Salgado 2012; Teixeira et al. 2012; Pula and Rozanski 2012; and Chan and Low 2012) showed that the reliability analysis of pile foundations subjected to axial as well as lateral load has been one of the important current research topic in geotechnical field. Probabilistic based performance criteria were quantified for a single pile and pile groups in cohesionless soil by Eloseily et al. (2002). A p-multiplier approach was incorporated into the analysis to modify the p-y curve for a single pile to obtain the p-y curve for individual piles in a pile group. A statistical analysis of set up capacity of pile was carried out from the database of a large number of pile testing data in clay by Yang and Liang (2006). Load and resistance factor design (LRFD) using FORM was used for examining the different load and resistance factor for different target reliability index. Limit state analysis of drilled shaft was performed by Misra and Roberts (2006) in probabilistic framework. The fuzzy based reliability analysis (Dodagoudar and Venkatachalam 2000; and Park et al. 2012) of the earth slope was reported in the literature. Dodagoudar and Venkatachalam (2000) presented a new approach, called fuzzy point estimate method (FPEM) for reliability evaluation of earth slope. Park et al. (2012) reported a hybrid approach, fuzzy set theory in conjunction with Monte Carlo simulation technique, to determine the failure probability of earth slope. Second Order Reliability Method"

Jan 1, 2015

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By S. P. Mukherjee, Smita Tung

"Piles are generally subjected to uplift in case of under ground and water front structures. Sometimes piles are also to resist uplift loads in transmission towers, dry rock, and so on. Experimental investigations of single piles and pile groups have been carried out using model hollow circular aluminum piles, having 25.4 mm outer diameter and lengths of 600 mm, 750 mm and 900 mm. Pile groups of 2?1 and 2?2 arrangements have been used in the experimental investigations. L/d ratio has been kept equal to 24, 30 and 36 in all the cases. All the single piles and pile groups have been tested under vertical uplift. Spacing between two piles in a group has been varied with respect to pile diameter such that spacing to diameter ratios of pile are 3, 4 and 5 in case of pile groups. An attempt has also been made to analyze those models of single piles and pile groups under vertical uplift by PLAXIS 3D software. Good analogy has been observed between the results of experimental and numerical studies. A parametric study has been carried out to observe the variation of ultimate uplift capacity of pile groups with spacing and depth of embedment. It is observed that for a particular embedment length of pile and a particular group arrangement the ultimate uplift capacity increases with increase of spacing. It is also investigated that for a particular spacing and particular group arrangement, the ultimate uplift capacity increases with increase of embedment depth. Those variations have also been presented with graphs which are generated considering non dimensional forms of parameters. The paper brings out change in pullout capacity of pile groups with spacing and embedment depth of piles.1. INTRODUCTIONPrediction of uplift capacity of single piles and especially of pile groups is one of the most interesting areas of research in geotechnical engineering. Pile foundations are frequently used to transmit the superstructure loads to deeper strata if the subsurface soil is of inadequate strength. The worst possible case may be considered to occur when all the piles in a group subjected to uplift. In cohesionless soils, the shaft resistance is an important source of pile capacity under axial loading, especially when the pile is subjected to uplift loading. Poulos and Davis (1980) recommended estimating the uplift capacity of piles as 2/3 of the downward shaft resistance. Later Ramasamy et al. (2004) indicated that the upward shaft resistance is significantly less than the downward shaft resistance. Some studies were conducted on the behavior of a single pile under uplift loads, such as those by Sowa (1970), Vesic (1970), Das and Seeley (1976), Levacher and Sieffert (1984), Rao and Venkatesh (1985), Chattopadhyay and Pise (1986), and Shanker et al. (2007). Das et al. (1976) conducted a model study to test the uplift capacity of single piles and pile groups buried in sand, and they also determined a relationship between the efficiency of a pile group and its spacing. Chattopadhyay and Pise (1986) proposed an analytical method for predicting the uplift capacity of piles embedded in sand and obtained reasonable agreement between experimental and theoretical results. Gaaver (2013) investigated experimentally that an upward displacement of about 1.4–2.5% of the pile diameter is required to attain the net uplift capacity for both single piles and pile groups. The uplift resistance of pile groups depends on the several variables like group size, shape, spacing to diameter ratio of piles, embedment depth to diameter ratio of piles, soil type and its density and soil-pile friction angle."

Jan 1, 2015

By José Carlos do Amaral, Marcelo Groszownik, Jorge Beim

"Initiated in 2008, the project of this 1800 km long Electrical Transmission Line is a job of extreme technical complexity, crossing regions of major forests and rivers. When ready, it will allow the large Brazilian states of Amazonas, Amapá and Pará to use the energy from hydroelectric plants, thus eliminating the need for the use of diesel fuel thermal plants, with their much larger environmental footprint. Due to its extraordinary characteristics, the Green Peace and the Discovery Channel constantly visited the job. The part between the Amazon and the Xingu rivers started in 2012, and encompassed about 100 transmission towers with up to 150 m height, through a region known as “Alagados”. This region exhibits a 1.5 m water level during the rainy season, and soaked ground the rest of the year. Navigation of regular vessels is impossible during the flood season, when a dense vegetation called “bulhado” fills the riverbed, and vehicle traffic is impossible during the dry season, due to the extremely low surface soil resistance. Great logistical and technical difficulties were encountered for driving and determining the capacity of the piles. New systems had to be developed for driving the piles, with the simultaneous use of 15 small piling rigs. The final penetration, total number of hammer blows during driving, plus Dynamic and Static Load Tests were used for determining the driving and acceptance criteria.The geographical challenge and initial conditionsThis paper describes the execution of foundations for a 500 kV Electrical Transmission Line in a region that becomes flooded during the rainy season and heavily muddy during the dry season. This is the monsoon climate, typical of the equatorial region of Brazil, where there is a rainy season lasting for about half the year, followed by a very dry season. The temperature varies very little throughout the year, due to the proximity to the equator. The locals call the rainy season “winter” and the dry season “summer”.The most important part of the so-called “Alagados” region is situated inside an Environmental Extractive Reserve (RESEX) called “Verde para Sempre” (Forever Green), created in 2003. This is one of the largest environmental reserves in Brazil. It is an area controlled by the Brazilian Environmental Control Department, the Chico Mendes Institute (ICMBio). The environment control parameters are very strict.No deep foundation had ever been executed before along the “Alagados” region. The main challenge faced on this job, however, was working in a place where self-propelling vessels or land vehicles and equipment cannot be used. During the rainy season there is a dense and intricate vegetation called “bulhado”, which prevents the movement of outboard motor boats with propellers going deeper than 50 cm. In the dry season, the heavy mud prevents the movement of foundation equipment, excavators, trucks and other machinery."

Jan 1, 2015

By Abolfazl Eslami, Sepide Lotfi, Mohammad M. Eslami

"Via direct CPT methods for pile capacity prediction, correlation coefficients smaller than unity are used to relate cone tip resistance (qc) and sleeve friction (fs) to pile toe capacity (rt) and shaft capacity (rs), respectively. For linking CPT data to pile capacity, factors such as diameter, penetration rate, partial embedment of pile toe into a hard layer, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered. The aim of this paper is to investigate the role and significance of scale effects and establish direct relation between CPT data and pile shaft capacity. A database has been compiled including 40 full scale pile load tests and CPT sounding records for calibration and validation of the proposed approach. Analytical studies demonstrate that differences between pile and penetrometer penetration rate, geometry, and stress-strain conditions influence the relation between fs and rs. By considering the determinants, a procedure is proposed from which the pile shaft capacity can be predicted. This approach demonstrates better agreement with measured capacity by static loading test and less scatter than other current CPT methods.IntroductionAmong different approaches for pile capacity prediction, in-situ tests such as SPT and CPT have been used as supplementary of static analysis. Due to similarities between CPT and pile, the measured cone tip resistance and sleeve friction can be employed for prediction of unit toe and shaft capacities, respectively.Determination of pile capacity from CPT data includes two main approaches: direct and indirect methods. Direct CPT methods apply the measured values of cone tip resistance (qc) for pile toe capacity (rt), and sleeve friction (fs) for pile shaft capacity (rs) with some modifications regarding scale effects. Indirect CPT methods employ friction angle and undrained shear strength values that have been estimated from CPT data.When using direct CPT methods to relate qc and fs to rt and rs, correlation coefficients smaller than unity are used. Factors such as diameter, penetration rate, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered for correlation between CPT and pile capacity. The work presented in this paper aims toward ameliorating the situation in the area of pile shaft capacity prediction, based on cone sleeve friction.Case histories from full-scale tests are compiled and analyzed by means of six methods including five direct CPT methods for shaft capacity prediction and the proposed method."

Jan 1, 2015

By Sanjay Gupta, Sorabh Gupta, Ravi Sundaram, Abraham Varghese

"Geotechnical investigation for the Kochi Metro revealed a critical section of the Viaduct near Ernakulam Junction Railway Station. Four piers, located over a 220 m stretch, were passing through an area with substantial thickness of soft clay. The scope of the geotechnical investigation included two boreholes and a static cone penetration test at each pier location. In the boreholes, field vane shear test was conducted at different depths in addition to the routine SPT. The design of heavily loaded piles in such strata is a challenge due to the liquefaction of the shallow sands and negative skin friction / down-drag in the soft under-consolidated clay. Bored cast-in-situ piles of 1500 mm diameter extending to 50-60 m depth were used to carry 500-600 tonnes load.INTRODUCTIONThe first phase of the rapid transit system at Kochi, Kerala (See Fig. 1) whose elevated route spans from Aluva to Thripunithura covers a total distance of about 25 kilometers. One of the more critical sections of the viaduct exists near the Ernakulam Junction Railway station where the alignment takes a sharp curve to move towards Vyttila, crossing the railway tracks and running partially over the approach of South over-bridge.In this section, four piers located on either side of the railway tracks near the Route Relay Cabin of Ernakulam Junction Railway Station pass through an area with substantial thickness of soft underconsolidated clay.The alignment is geotechincally challenging due to the presence of loose liquefiable sand and soft underconsolidated and sensitive clay.Initial investigations by the owner based on limited boreholes only yielded conservative and inconclusive pile capacities. For a thorough understanding of the soil behaviour, a detailed geotechnical investigation was carried out to assess the engineering behaviour of the soil strata.The scope of the geotechnical investigation included two boreholes and a static cone penetration test at each pier location. In the boreholes, field vane shear tests were conducted at different depths in addition to the routine SPT."

Jan 1, 2015

By Rick Piovesan, Pramod Rao, Nihal Bohra, Mark Wahler

"This paper discusses the approach followed for the geotechnical design of 355 mm and 457 mm diameter driven open-ended steel pipe piles used for a gas plant at a green field site in Pilbara region in Australia. The principal bearing layer at the site comprises of calcareous Red Bed soils and weak rock, which is the typical geology along a significant length of the northern Western Australian coastline with carbonate content up to 70%. The uncertainty associated with the mechanical behavior of the calcareous soils and cemented soils (weak rocks) presented design challenges in the selection of appropriate pile design method and design parameters for pile capacity estimation during Front End Engineering Design (FEED). The American Petroleum Institute (API)-based design methodology was adopted. The representative design parameters for the Red Bed weak rock were established by treating the weak rock as clay with undrained shear strength as one-half of the characteristic unconfined compressive strength (UCS) value. Both statically load tested and CAPWAP (Case Pile Analysis Wave Program) estimated ultimate axial pile capacities on 25 early pre-production indicator piles demonstrated that the API design methodology for siliceous soils provides reasonable prediction of axial pile capacity in the red bed soils/weak rock and no reduction to API computed axial capacity due to carbonate content is warranted. The results also demonstrated that penalizing axial pile capacity solely based on carbonate content is not appropriate.IntroductionA gas processing facility was proposed to commercialize the gas reserves located 130 km offshore from the north-west coast of Western Australia (WA). The project site is a green field site located in the Pilbara region along the northwest coast of WA. Specific information regarding the site has been withheld due to confidentiality reasons. The site layout is shown in Figure 1.The site comprises low-lying tidal flats, clay pans and sand dunes covered with low scrub. The onshore site levels vary from elevation 1 m to 10 m AHD (Australian Height Datum), with the largest proportion of the area (excluding sand dunes) between elevations of 1 m and 3 m.The onshore facilities are to comprise a liquefied natural gas (LNG) plant site, a construction camp, the land-based portion of the materials offloading facility (MOF), roadways, and borrow pit areas.The existing ground levels within the process train area, where pile load testing was performed, vary from over 7 m AHD where the summits and peaks of the central dune exist to typically 1 m to 2 m AHD towards the east and west edges of the dune. The proposed finished grade for the process train is set at 7 m AHD."

Jan 1, 2015

By João Veludo, Eduardo Júlio, Helen D. Robinson, Jesús E. Gómez

"Utilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. The study resulted in important conclusions on the mechanism of connection capacity development and provided specific recommendations for practical design of micropile-to-footing connections. In the last five years, the original study was complemented by an intensive experimental effort in Portugal aimed at answering many of the questions still remaining on this topic. This paper is a summary of the knowledge that is presently available on the capacity of micropile-to-existing footing connections. It presents the results and observations of model tests performed in the US and Portugal, as well as some tests from actual construction sites. The paper presents clear evidence that friction may be the most important component of connection capacity. It also presents a clear correlation between confinement and connection capacity.IntroductionUtilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. This is often accomplished by drilling through the footing and developing the connection by direct bond between the micropile grout and the existing concrete. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. Smooth and textured micropile inserts of varying lengths were tested to failure inside pre-drilled holes of varying diameters. That investigation led to several publications (Gomez et al. 2005, Wilder et al. 2005, Cadden 2009) on the mechanism of development of bond strength between micropiles and concrete, which included a chart for preliminary bond value selection depending on the diameter of the hole and texture of the micropile.An intensive testing program was carried out in Portugal in the last five years. The program focused on answering questions posed by the original investigation and on finding the relationship between connection capacity and level of confinement. Both investigations, and especially the testing performed in Portugal, provided an invaluable amount of information on the mechanisms of failure of micropile-to-footing connections. This information should be the basis for development of design procedures that, until now, were not available."

Jan 1, 2015

By Daniel W. Mageau, Larry W. Applegate, Aaron K. McCain

"An innovative method of ground freezing was successfully tested to create a “dry” excavation condition for a new building foundation at a site in downtown, Miami, Florida. The subsurface conditions in Miami generally consist of very porous, weak limestone and sand with groundwater near the surface. Water flow through these materials can be very high. Dewatering is extremely restricted in Miami so deep below-grade structures are rare and expensive. A new, innovative method to allow deep excavations in dry conditions without dewatering involves the creation of a thick, temporary, frozen soil plug below the planned excavation depth across the entire site to cut off vertical groundwater flow during construction. Frozen soil is impermeable and very strong and has long been used for temporary structural and water-tight shored walls. Using the same proven principals, frozen soil plugs are very effective at cutting off water from the bottom of the excavation as well as resisting upward buoyant forces. This new freezing method can be used for fairly deep excavations in new building construction supported on deep foundations. The building piles act as temporary anchors for the frozen plug to resist very high upward buoyant pressures until the permanent structural slab is completed.IntroductionUnlike other Cities, below grade basements are rare in Miami. The few basement foundations constructed have utilized a cumbersome and expensive method of excavation and shoring involving underwater excavation, tremie slabs, and commercial divers. The key issue for underground construction in this area of the country is the vertical flow of groundwater through the base of the excavation. To deal with this issue in the past, the contractor first installed all of the building piles and the perimeter shoring walls. Then, interior sheet pile walls are installed to create small manageable excavation pits. Each pit is then excavated through standing water “in-the-blind” and around the buildings support piles. The final excavation, interior struts, and inspection is performed by commercial divers. Finally a thick foundation tremie slab is poured under water. This method could be successful but proved to be time consuming and expensive. In addition, some building piles were occasionally damaged during the under-water construction process."

Jan 1, 2015

By Kenneth Gavin, Weichao Li, Paul Doherty

"The lateral load capacity is one of the most important issues to be considered in designing piles to resist berthing loads, ship impact forces and for monopiles used in the offshore wind sector. A number of semi-empirical design approaches are available to calculate the ultimate soil resistance and assumed soil reaction profile along the piles’ embedded depth. In order to investigate the response of monopiles to lateral loading, a series of field experiments were conducted on instrumented steel pipe piles. Two lateral loading tests were performed on model piles with a diameter, D, of 340 mm and embedded depth, Lem, of 2.2 m, giving a Lem/D ratio similar to those adopted in the offshore wind sector. The piles were driven into dense sand at the University College Dublin geotechnical test bed site in Ireland. 10 pairs of strain gauges were installed on each model pile along the embedded depth at 10 levels to capture the load transfer and bending moment within the piles. The deflection and rotation at the model pile head were measured by Linear Variable Differential Transformer (LVDT) and inclinometers. The tests results were used to perform a detailed evaluation of current design methods. In the final section, discussion on the determination of the ultimate lateral load capacity for monopile design was conducted. IntroductionA pile’s lateral load capacity is determined, for design purposes, by two conditions: 1) the ultimate lateral load, Fu, divided by an appropriate safety factor; and 2) the load according to the maximum lateral deflection that the support structures can sustain. In view of the first condition, design methods to calculate the ultimate load were developed for piles used in the offshore oil and gas sectors, which tend to be much more slender than monopiles used in the wind industry. The purpose of this study was to investigate whether these design methods provide reasonable estimates of ultimate capacity, for short rigid monopiles.The methods to determine the ultimate lateral load generally follow three steps: 1) determine the ultimate soil resistance, Pu, along the pile embedded depth; 2) adopt the most appropriate soil reaction profile, Pz, along the piles embedded depth when the pile subjected to the ultimate lateral load condition (four of the most popular ones are depicted in Figure. 1); and 3) ensure equilibrium of lateral forces (see Equation 1, symbols are listed at the end of the paper) acting on the pile and bending moments (see Equation 2) about a point in pile is employed to determine the ultimate lateral load."

Jan 1, 2015

By Anup Kumar Mandal, Sanjoy Chowdhury, Biswajit Das

"Tailing pond of an iron ore mine necessitated raising the height of its embankment to create additional storage capacity. The tailing pond is located in eastern India and raising the height of embankment was going on during the month of January, 2014. Upstream method of construction was adopted since there was no space available at the downstream side. During the construction, about 200 m stretch of the north east embankment of height about 5.5 m failed forming a classical slip circle on the upstream side involving about half the top width of the embankment. To find out the root cause of the slope failure, detail geotechnical investigation work was carried out within the embankment as well as in the adjacent areas within the pond. About 7.5m thick very soft tailings were detected below the constructed embankment. Shear strength of the soft tailing was very low and was inadequate to sustain imposed embankment load. This resulted in the failure of the embankment. Analysis of the tailing deposit revealed that even after failure, settlement was continuing due to imposed embankment load. Under normal onedimensional consolidation, the tailing deposit would have taken about 5.7 years for 90% of primary consolidation. However, in order to mitigate the scarcity of storage space, mining plan required raising the height of the embankment within next six to eight months. Therefore, despite the fact that there was a failure, it was necessary to continue the construction on the underlying weak stratum. The system was redesigned with installation of prefabricated vertical drains (PVDs) to accelerate the consolidation process thereby gaining the in-situ strength. Strength was additionally enhanced by installing geogrids in multiple layers. It stabilized the existing embankment and also ensured construction of additional height over and above the existing embankment.INTRODUCTIONBeneficiation plant in the Iron mines enhances the mineral content by separation of contaminants and fines. The residue (waste material) is called tailings/tailings depending upon the grain sizes. These tailings in a slurry form are generally disposed in a pond called as tailing pond/tailing pond. Height of embankment of such ponds is increased either by upstream or by downstream or by centrally raising methods in different phases as quantum of deposition in the pond increases with time."

Jan 1, 2015

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By Brandon Buschmeier, Frederic Masse

"Inclusions are a type of ground improvement that provide an improvement of a soil mass by insertion of a material with better characteristics than the surrounding soils. There are primarily two types of inclusions: “Soft” inclusions which are constructed of granular material (Stone Columns, Rammed Aggregate Piers, VibroPiers...), and “rigid” inclusions which are constructed of grout inserted with or without pressure (VibroConcrete Columns, Controlled Modulus Columns, Soil Mixing Columns).While the central principle of the inclusions is similar (i.e., overall improvement of characteristics of the soil mass below the structure), the load transfer mechanism is radically different for each technique. Therefore, the applicable design methodology is specific to the type of inclusions and there exists no universal method of design which spans across all inclusions.This paper will present an in-depth comparison between the standard design methods used for “soft” granular-type inclusions (Priebe modified, Balaam & Booker, Goughnour & Bayuk...) and the methods used for “rigid” inclusions which mainly rely on finite element analysis. The paper will explain why the design for soft inclusion methods cannot be applied to rigid inclusions and vice-versa. Each design method will be reviewed in detail to better emphasize its limitations and advantages.Two case histories will also be presented; one for each type of inclusions in order to illustrate the concepts developed in the first part of the paper.1 INTRODUCTION1.1 GENERAL OVERVIEW OF GROUND IMPROVEMENT WITH INCLUSIONSThe use of ground improvement methods to provide the appropriate amount of foundation support is a growing and constantly evolving industry. Traditional structural foundation methods including ‘shallow’ and ‘deep’ foundations do not adequately address the wide range of settlement tolerances, soil conditions, and loading considerations inherent to each unique potential project. In some instances, ‘shallow’ foundation solutions are simply not feasible due to soil and loading constraints. Furthermore, ‘deep’ foundation solutions are used to ‘bridge’ the soft compressible soils, ensuring that the entirety of the load in the structure is transmitted through individual elements into competent layers below the ground surface (bedrock, dense residual soils). Highly concentrated structural loads are transferred into the individual elements by means of direct contact requiring the use of structurally rigid surficial components (structural slabs, grade beams, and pile caps).Ground improvement bridges the gap between these two traditional methods, offering adequate foundation support while using more costeffective techniques and design methodologies. Inclusions are a type of ground improvement used to provide a reinforcement of the soil mass through the vertical insertion of a material with better characteristics than the surrounding soils. Much like deep foundations, inclusions are installed through soil layers with high compressibility and/or low bearing capacity and terminated in a suitable bearing stratum. However, unlike deep foundations, ground improvement inclusions rely on a distribution of load between the soil and the inclusions. By doing so, some of the structural load is applied directly to the soil in a proportion equal to its bearing capacity and compressibility limits, while the rest of the load is shed into the vertical inclusions down to the bearing stratum. Load sharing is a critical aspect in the performance and design of the various ground improvement methods."

Jan 1, 2015

By M. Hesham El Naggar, Tony Sangiuliano, Alper Turan

"Bridge abutments supported on pile foundations are often constructed over weak and compressible soils. The consolidation settlements induced by the embankment loads are known to result in downdrag and lateral forces on the piles supporting the bridge abutments. The performance of a pile group including inclined piles embedded in consolidating soils was investigated numerically considering surcharge loads from approach embankment construction. A two-dimensional numerical model was constructed using commercial finite element software PLAXIS and calibrated against field measurements of the abutment movements observed on Brookdale Avenue Underpass Structure located on the Macdonald-Cartier Freeway in Ontario between Cornwall and the Quebec border. The soft soil model (SSM) was used to simulate the constitutive behavior of the compressible soil deposit. The SSM model parameters were determined based on the laboratory tests. Subsequently, time dependant development of downdrag effects was comparatively evaluated for vertical and inclined single piles as well as a pile group that included both vertical and inclined piles.Results showed that drag loads increased with the consolidation time. However, majority of accumulation of drag loads took place within first 120 days after installation of piles. The results also indicated that the shear forces and bending moments are controlled by the lateral spreading of foundation soil and their accumulation is proportional to consolidation time. The large axial strains caused by large downdrag forces are considered to have yielded the piles and this is a possible reason for unusual abutment movements. The results presented in this study are considered to be of interest to researchers and practitioners.1. IntroductionDeep foundation units are widely used for supporting bridge piers and abutments, where weaker surficial soils preclude shallow foundations. Particularly in Ontario, semi-integral and integral abutment bridges are typically supported on end-bearing steel driven piles. The construction of approach embankments over weaker, compressible soils results in significant vertical and lateral soil movements, which induce additional loads on piles supporting the abutments. In order to minimize such effects, preloading and surcharging are commonly employed approaches to avoid unanticipated settlements prior to the installation of piles. Other alternatives such as aggregate pier supported approach embankment are also being studied as the schedule restrictions imposed by preloading and surcharging becomes cost prohibitive (Turan et al. 2012)."

Jan 1, 2015

By Abu B. Siddique, Anthony S. Crincoli

"The New Jersey Turnpike Section 2 widening program consisted of widening between Interchange 6 in Mansfield Township, Burlington County and Interchange 9 in East Brunswick Township, Middlesex County. To accommodate large volume of traffic the roadway was widened from 6 to 12 lanes with major modifications performed at four interchanges. The Section 2, NJTA Interchange 6 to 9 Widening Program is a 4.2-mile section of Turnpike roadway which included a total of 12 new or modified structures. In order to facilitate the construction process Section 2 was divided into three construction contract packages. This paper will cover the last and final Contract T869.120.203 which is 1.7 miles in length. The work generally consisted of eight new ramps connection to and from the toll plaza to the new inner and outer roadways. New mainline bridges were constructed over several ramps. A new bridge was constructed to take northbound outer lanes traffic over two ramps along with new mainline bridges over Black’s Creek, Georgetown Road, and Laurel Run. In addition, a new bridge was constructed to take a ramp over Laurel Run and the existing U-turn Bridge was replaced with a new one.For Contract T869.120.203 a total of 74 five-foot diameter drilled shafts has been constructed to support all pier foundations for bridges. Three drilled shafts were tested using Osterberg Load Cells to verify the estimated shaft resistance during design phase. One Osterberg Load Cell test was performed on a demonstration (sacrificial) shaft and the other two Osterberg Load Cell tests were performed on production shafts. This paper compares the estimated total, side and tip resistances with corresponding measured total, side and tip resistances and provided recommendations for future design purpose.INTRODUCTIONTo accommodate large volume of traffic the New Jersey Turnpike Authority (NJTA) decided to widen Section 2, which included Interchange 6 through Interchange 9. The Section 2, a 4.2-mile section of Turnpike roadway that was widened from 6 to 12 lanes with major modifications performed at four interchanges.The New Jersey Turnpike Authority (NJTA) procured AECOM to perform engineering services for the final design of Section 2, NJTA Interchange 6 to 9 Widening Program. Section 2 is a 4.2-mile section of Turnpike roadway that will widen from 6 to 12 lanes and will include a total of 12 new or modified structures. It encompasses modifications of the existing and the design of four new ramps at Interchange 7. The project also includes the modification of two local roads over the mainline, two local roads under the mainline, two maintenance U-turns, and retaining walls. In addition, the project consists of the design of noise walls, sign structures, storm water management basins and the more typical drainage, utilities, lighting, roadway, ROW, and signing and striping design."

Jan 1, 2015

By James L. Christensen, Gregory Sanchez, Michael P. Walker

The Fogg Museum expansion project required excavation and construction in a congested urban area in Cambridge, Massachusetts. A soldier pile tremie concrete (SPTC) wall provided the support of excavation and now serves as the permanent basement wall of the new expansion of the museum. The existing Fogg museum had a single basement level. The new expansion has a two-level basement for new exhibit space and an amphitheater. The east side of the site is about 20 feet above the basement level of the existing Fogg structure which resulted in a significant unbalanced load that needed to be resolved without damaging the original Fogg structure. The SPTC wall was supported with a combination of tiebacks and internal bracing. The final depth of the excavation was about 40 feet below street level. Strict movement control was imposed because the existing museum contained an Italian Renaissance-style courtyard. The southeast corner of the SPTC wall had to accommodate underpinning of an historic concrete ramp which was ultimately incorporated into the expansion. Challenges during construction included excavating the SPTC wall panels up to 12 feet into argillite bedrock which had occasional diabase dikes and sills. The following topics are discussed in more detail after a general project.

Jan 1, 2015

By Abolfazl Eslami, Masoud Zare, Ali Asadi, Ali Abrang

"Physical small scale models for study of deep foundations can be performed in simple chambers (1g), calibration chambers (CC), and centrifuge apparatus (ng) which involve some limitations and difficulties. In recent years, Frustum confining vessels (FCV) have been developed for physical modeling of deep foundations. This device is frustum of a cone shape that applies a steady pressure on its bottom and creates a linear stress distribution along its vertical central line. A new FCV which has been built in AUT is introduced. This device has a height of 1200 mm, top and bottom diameters of 300 and 1300 mm, respectively. Through the application of bottom pressure up to 300 kPa, the insitu overburden stress conditions equivalent up to 40 m soil deposits consistent to the embedment depth of commonly used piles. Observation indicated that there is approximately a linear trend of stress distribution, and this device can create realistic overburden stress in the desired control volume along the central line. Moreover, a couple of compressive and tensile load tests were performed on steel tubular open end model piles driven in sand with length of 750 mm and different diameters and L/D ratio between 8-15. Comparison of load capacity between tested and full scale piles demonstrate a suitable conformity for similar confinement conditions. Therefore, the FCV can be realized as an appropriate apparatus for investigation of piling geotechnical behavior and examination of construction effects.IntroductionDeep foundations are designed as foundation system for supporting heavy loads, high rise and important structures. Different theoretical, numerical and experimental approaches have been developed to study the geotechnical behavior of deep foundations. Experimental methods are employed to clarify directly pile-soil interaction and because of repeatability, analogy, rapid measurement and cost efficiency, physical modeling can be realized as an intermediate technique compared to element testing and full scale load tests."

Jan 1, 2015

By Manuel M. Reyes, Thuraisamy Thavaraj, Alex Sy

"The new east span of the San Francisco-Oakland Bridge features a single tower self-anchored suspension (SAS) bridge. During construction of the SAS bridge, a temporary bridge was used to support the box girders until erection of suspension cables was completed. The transfer of deck load from the temporary bridge to the suspension cables was achieved in November 2012 and the SAS bridge has become the largest of its kind in the world. The new bridge will be in service in Fall 2013.Large diameter driven steel pipe piles were used for the temporary bridge foundations at Towers D, F and G located in San Francisco Bay. At Tower D, the large diameter steel pipe piles were driven through thin overburden into bedrock using a large Menck MHU500T hammer with a rated energy of 550 kJ. As there was no precedence in driving open-ended pipe piles into the Franciscan Formation bedrock, challenges were faced with uncertainties in drivability, driving stresses, pile embedment in bedrock and pile capacity. These uncertainties were addressed by incorporating additional measures into the pile design, and by the use of dynamic pile monitoring during initial driving and re-strike. Pile relaxation was observed during pile installation.At Towers F and G, setup effect was a key issue for the piles driven into the deep soft marine sediments. Drivability analyses were conducted to predict pile run, driving stresses, selection of hammer and refusal criteria. The piles were dynamically monitored during driving to estimate pile capacities. Due to the set-up effect in the Bay Mud, the piles gained up to 3.3 times the initial capacity during the re-strike and were in excess of the design capacity.This paper presents details of the design, construction, testing and performance of the driven pipe piles at temporary Towers D, F and G. Settlement data of the temporary tower foundations while in service confirmed the satisfactory performance of the pile foundations.INTRODUCTIONThe new east span of the San Francisco-Oakland Bay Bridge features a single tower self-anchored suspension (SAS) bridge, the largest of its kind in the world. The new east span replaces the existing double-deck steel bridge built in the mid-thirties. A span of the existing bridge had collapsed during the 1989 Loma Prieta earthquake but was repaired. Construction of the new east span commenced in 2008 and is expected to be completed for the Labour Day opening in 2013. Figure 1 shows a schematic (looking north) of the new bridge with its 160 m high main tower T1 in the middle, and Piers W2 and E2 at the west and east ends, respectively. The west and east spans of the SAS bridge are 180 m and 385 m, respectively.During construction of the SAS bridge, a temporary bridge, complete with towers and trusses, was used to support the box girders of the new permanent bridge until the loads from the box girders were transferred through suspension cables to the permanent bridge. The transfer of deck load from the temporary bridge to the main cable was completed in November 2012."

Jan 1, 2015

By Terrence M. Carroll, Chu E. Ho

"A pile installation and load testing program on driven tapered piles was undertaken at John F. Kennedy International Airport in New York City for the extension of the existing Terminal 4. As part of the program, dynamic testing by means of the Pile Driving Analyzer (PDA) was performed on several preliminary test piles as well as production piles. The results of the dynamic tests and subsequent static load tests were reviewed to develop an understanding of the pile-soil response of a tapered pile during driving and after setup. Pile setup occurred as a result of increase in shaft resistance with virtually no increase in toe resistance. More than 150 tons of additional capacity was gained after the setup time.The capacities measured during driving from the PDA are typically used as the basis for determining the pile driving set criteria, with the required initial driving capacities determined largely by the contractor’s experience. An improved appreciation of the setup phenomenon is required to better refine the driving criteria at the end of initial driving such that the required ultimate capacities can be obtained, with reasonable confidence, after a period of setup.This paper presents interpretation of pile-soil behavior from Case Pile Wave Analysis Program (CAPWAP) analyses and discusses the mechanism of increased capacity as a result of setup effects. Time-dependent capacity gain as a result of setup effects should be based on the extrapolation of the shaft resistance component rather than the total pile capacity as is commonly practiced. Prediction of pile performance using this approach was in good agreement with observed static and dynamic load test results.IntroductionTapered piles have been adopted for various projects at John F. Kennedy International Airport (JFKIA) since the late 1940’s. Initially timber piles were used exclusively, with steel Monotube piles being used from at least the 1980’s (Horvath and Trochalides, 2004). The steel Tapertube pile was developed in the mid-1990’s and has commonly been used in recent construction (Brusey and Yin, 2008). The Tapertube piles used for this project consisted of a 25 foot long tapered section that was 8 inches in diameter at the tip and 18 inches in diameter at the top. An 18 inch diameter straight pipe was welded above the tapered section."

Jan 1, 2015

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015