Search Documents

By N. B. Devi

The extraction of copper(II) from sulphate solution was investigated using LIX®984N in kerosene. The parameters that could affect the extraction, such as equilibrium pH, extractant concentration, salt concentration, various diluents, and temperature, were separately investigated. On the basis of slope analysis, the complex formed in the organic phase is proposed to be CuR2, where R is the anionic part of LIX®984N. The extraction equilibrium constant and Gibbs free energy ( G) of the extraction process were determined. The positive value of H obtained from temperature variation studies showed that the extraction process is endothermic. The extraction of copper was lowest when chloroform was used as the diluent. Separation and recovery of copper from a synthetic copper-nickel solution containing 6.35 g/L Cu(II) and 0.58 g/L Ni(II) was carried out using 20%(v/v) LIX® 984N. The separation factor ( = DCu/DNi) was found to be pH-dependent. A two-stage batch countercurrent extraction was carried out at an O:A ratio of 3:4 at equilibrium pH 1.05 for extraction of copper from copper-nickel solution, followed by copper stripping from the loaded organic phase with 15% H2SO4 at an O:A ratio of 3:1.

Jan 1, 2014

By Andrei Yevdokimov, Ivan Sidorov, Olga Lanchakova, Olga Khmelnitskaya, Tatiana Chikina

"The paper focuses on the results of the research on development of hydrometallurgical process of gold recovery from refractory sulfide flotation concentrates based on fine and ultrafine grinding. Refractory concentrates (the degree of refractoriness is 16.9%-82.6%) were chosen for testing. The efficiency of the process based on fine and ultrafine grinding to treat flotation concentrates with gold intergrown with sulfides and rock-forming minerals was shown. Based on the test work conducted, the process option was chosen. In included grinding of flotation concentrate to the size of 98% minus 20µm in a bead mill, lime treatment with air blow, CIL, filtration and detoxification of liquid phase of the slurry. This process (compared to the basic option) provides the recovery of gold from 82.6%, up to 94.0% and decreases the residual grade in the tailings from 3.3g/t to 1.1g/t at the consumption of 12.6NaCNkg/t. Based on the results of the test work and pilot plant testing, project design criteria of flotation circuit at a Russian plant was developed."

Jan 1, 2014

By X. Q. Wu

Magnetization in slurry (MIS) of weakly magnetic minerals by iron ions was investigated. The magnetic seeds (strongly magnetic particles) were synthesized by ferruginous chlorides directly in slurry instead of previous preparations of magnetic seeds by finely grinding mineral magnetite or specially synthesizing them separately in an aqueous solution. In this way, the growth of the seeds and their adsorption on the minerals simultaneously take place in the same slurry. That after MIS the recovery of weakly magnetic mineral limonite in a magnetic separator increased means the formation and adsorption of magnetic seeds on the surface of iron mineral limonite. The magnetization effect was evaluated by limonite recovery at a magnetic strength of 3.500 Gs in a magnetic separator. Mineral limonite was properly magnetized in the following slurry condition: molar ratio of Fe3+ to Fe2+1:3, slurry temperature of 45 °C and pH 10.5. The selectivity of the magnetization between minerals limonite and quartz was improved by adding surfactant sodium oleate.

Jan 1, 2014

By Ken Goering

"Bridgestone Americas opened the company’s first U.S.-based giant off-road radial (ORR) tire plant in November. The 139,000-m2 (1.5 -million-sq ft) plant, located on a 222-ha (550- acre) site in Aiken County, SC, will produce radial tire products, including 157-cm (63-in.) tires, used on mining and aggregate haul trucks.The plant, announced in 2011 as a $970-million investment, represents the largest investment that Bridgestone has made in the United States, and is also the single largest investment ever made in South Carolina. Although it had already been producing tires for a few months, the plant officially opened with a ceremony in November 2014, attended by South Carolina federal, state and local elected officials, as well as Bridgestone personnel from the United States and Japan. Prior to the Aiken County plant’s construction, all of Bridgestone’s giant ORR tires were manufactured at its Shimonoseki and Kitakyushu facilities in Japan.Kurt Danielson, president of Bridgestone’s U.S. & Canada Commercial Group, said the facility was built to primarily serve the North American mining and aggregate industries in a more efficient manner. "It’s a real change for us," he said of the U.S.-based plant at its opening ceremony. "This allows us to have a true global presence."The Aiken County plant is intended to allow Bridgestone to meet customer demand for ORR tires, Danielson said. "It really frees up our other plants in Japan to service the rest of the world, allowing us to serve our customers faster," Danielson said. "As soon as we build (a tire), we can have it to our customers."Tires manufactured at Bridgestone’s Japanese plants could spend up to a month in transit to the American continents; from initial mixing of the rubber and other compounds to being warehoused, tires manufactured at the Aiken County plant can be ready to ship in four to five days.Danielson said most of the tires built in Aiken County will be used by customers on the American continents. "We will export," he said, "but our desire is to use as much capacity as we can for the Americas."Ground was broken for the facility inSeptember 2011, when commodity prices were much different than today and global demand for tires had skyrocketed."

Jan 1, 2014

The Arctic is a region of special economic, geopolitical, research, socio-ethnic, and defense interests of both Russia and other countries of the Arctic zone. Introduction of innovation technologies at ore-processing factories is a direct responsibility of the state and this problem should be solved on the basis of coordination of interests of different stakeholders. The task of elaboration of scientific principles of rational state regulation in the North is very topical. Innovations require considerable investments first of all from private capital. However as an investment object innovations are not attractive for investors as they require large expenditures for long-term projects, and they are connected to high risks because market incentives form striving to get quick profits of private companies and result in a certain behaviour strategy while innovations need ?long money?. Under such conditions without state regulation of investment and innovation activities development of the mining sector in the Arctic practically has no prospects. At innovation development of mining enterprises economic growth is provided at the expense of active state innovation activities. The elaborated strategy of ore-processing enterprises should correspond to the modern paradigm of the ore-processing industry development which is not only for extraction of minerals but also for multi-profile structure having comprehensive use of the resources on the rational basis intended for rational complex utilization of mineral resources of the AZR which by the definition includes maximally full use of the whole aggregate of resources on the economically rational basis with obligatory environmental with resource reproductive and socio-economic functions and deterrents. The main principle of creation of innovation technologies is to obtain more products of higher quality with minimal costs. This allows increasing ?productivity of the resources? several times. This principle makes increasing productivity of the resources the most important and in this case efficiency of use of the resources brings extra profits at the expense of lack of new costs such as payment for protection and utilization of wastes. According to the economic theory only ratio between demand and supply is able to fix optimal proportions in economy and to give necessary signals for investment activities of mining enterprises. In this context market for minerals and increase of mineral resources productivity do not create incentives for investment activities without which neither sustainable economic growth nor solution of macroeconomic tasks are possible. Nevertheless countries should not reject this idea in spite of economic efficiency of the enterprises. Extraction degree of useful components and especially oil in the Arctic zone is one of the lowest in the world. This can lead to crisis of oil industry and other mining sectors. The reason for that is lack of a state policy of realization of innovation technologies in the mining sector in the Arctic.

Jan 1, 2014

By L. M. Wang

Chengmenshan Copper Mine Concentrator adopts the new process of preferential?bulk stage floatation and utilize reground, largely increase the mineral processing index of the copper and the sulphide concentrates. In addition, the paper describes the remarkable economic benefit of the new process through the comparison of the new and the old processes.

Jan 1, 2014

By A. E. Sobolev

The kinetics of hydrochemical oxidation of antimonite in solutions of nitric acid was studied using the rotating disk method and the factor experiment design. The dependences of the antimonite?s oxidation rate on concentration of nitric acid solutions, temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific oxidation rate at any combination of the values of the influencing factors were obtained. The oxidation process is found to proceed in a mixed mode, close to chemically controlled. Gradually, as the sediments of elemental sulphur and Sb2O5 accumulate on the disk surface, the process becomes controlled by internal diffusion. The observed high (more than second) order of the oxidation rate with respect to the concentration of nitric acid was explained by the autocatalytic action of the acid reduction products. The apparent activation energy depends on the stage of interaction. At the initial stage (in a mixed mode of the process proceeding), it depends on nitric acid concentration and varies from 31.5 kJ?mol?1 (in 2 M HNO3) to 36.1 kJ?mol?1 (in 10 M HNO3). This trend indicates the weakening of diffusion limitations with a nitric acid concentration increase. When the process is controlled by internal diffusion, the apparent activation energy was found to be 14.5 kJ?mol?1. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulphides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of antimony-bearing ores and concentrates.

Jan 1, 2014

By R. Armstrong

Due to limited available level ground, Nkomati Nickel Mine cut a weathered rock slope at the base of a mountain spur in order to create a platform for construction of the primary crusher plant and run-of-mine stockpiles. As space is limited around the mining area, ore processing at Nkomati is based on a high reliability of flow of material through the crusher plant, with minimal usage of other and larger designed stockpiles. Evidently, any crusher plant shutdown will render the mine as a whole unproductive and put excessive strain on the medium- to long-term large ore stockpiles, the deposition rates for which are restricted by founding material consolidation requirements. At the onset of the 2012 rainy season, movement was identified on the slope monitoring system and cracks developed on the slope. After a minor failure on the crusher slope an assessment of the slope stability was conducted and a slope management plan recommended, which included deployment of real-time monitoring. An evaluation of the conditions leading to instability was conducted and the likely causes for the failure identified. A full evaluation of the slope monitoring, rainfall, and mining conditions was undertaken and movement triggers were determined. This paper describes the events leading to the development of the failure and the evaluation of the monitoring data to determine a management plan for the failure that allowed for minimal shutdowns of the primary crusher.

Jan 1, 2014

By T. C. Sun

Two wasted activated sludges (WAS), from an industrial wastewater treatment and a sewage treatment plant respectively, and 7 collectors are used to investigate the feasibility of air flotation thickening of WAS by adding the collectors used in mineral processing. The collectors experimented include straight chain fat acids with different chain length, sodium oleate, alkyl sodium sulphonate, sodium dedecylsulfonate, and dodecylamine. The results show that the thickening efficiency varied depending on different collectors. Of the collectors experimented, dodecanoic acid and dodecylamine are best collector for thickening both sludges.

Jan 1, 2014

By Barton G. Stone

"Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole," (Baxter and Parks, 1939)."An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence, the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence."The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling."Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive." (McKinstry, et al., 1948).In an actual orebody, the accuracy of sampling depends not only on the number of samples but also on their proper distribution throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore, it is important to select the places in such a way that all parts of the orebody will be represented."

Jan 1, 2014

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By Robert Snow, Shibo Zheng, Wenyi Song, Xiaoqing Ma, Patrick Zhang

Numerous phosphate mineral depressants have been reported in the literature for use during anionic flotation of dolomite from carbonate fluorapatite in slightly acid circuits. In one part of this research, laboratory flotation experiments were conducted to compare the effectiveness of phosphate depressants to process ground, deslimed high-MgO Florida phosphate pebbles. Ten potential phosphate depressants were evaluated during laboratory anionic flotation of dolomite from phosphate in a slightly acid circuit using a sulfonated oleic acid soap plus oil as the dolomite collector. Eight of the depressants have been used by various investigators with foreign and domestic carbonate-phosphate ores. Four of the depressants were found to be reasonably effective during the current flotation study, namely: sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP), tetrasodium pyrophosphate (TSPP) and diphosphonic acid (DPA). Without depressants, the sulfonate collector required to produce cell underflow phosphate products containing <0.80% MgO and MgO/ P2O5 ratio <.033 was 1.13 kg/ton of flotation feed at a flotation pH range = 5.5-6.0. Using this collector level with 0.91 - 1.36 kg/ton of feed of STPP, SHMP or TSPP yielded phosphate products analyzing 0.73-0.92% MgO and MgO/ P2O5 ratios = .027-.034 at 90.0-96.8% P2O5 recovery. Similar grade phosphate products were obtained using DPA as the phosphate depressant at 84.1-87.5% P2O5 recovery. When no depressant was used, a similar grade phosphate product was obtained at only 65.9% P2O5 recovery. Another part of the research aimed at reducing MgO content in the final concentrate from Florida phosphate plants by conducting dolomite flotation on the final concentrate. Numerous phosphate depressants were tested for this purpose, including acidic, neutral and alkaline reagents. The most effective phosphate depressant was found to be phosphoric acid, giving both high grade and recovery.

Jan 1, 2014

By Steve Davidow, Nick Salisbury

"The Sunrise Powerlink project received numerous industry awards for excellence. The DFI C. William Bermingham Innovation Award recognized the innovative use of prefabricated steel micropile caps to increase safety, accelerate project schedule and minimize the project carbon footprint. DFI’s Outstanding Project Award (OPA) and World Cup of Micropiles Challenge Award honored the project as a whole and its positive outcome and industry example. Sunrise Powerlink involved construction of San Diego Gas and Electric’s (SDG&E’s) new 117 mile (188 km) 500/230 kilovolt transmission line from Imperial County to San Diego County, Calif. The alignment traversed a wide variety of geotechnical conditions, including desert, mountain and marine environments, and many of the 421 lattice tower structures used to carry the transmission lines were located in remote, rugged or environmentally-sensitive terrain.Micropiles were introduced as a solution to foundation construction in these challenging areas, which ultimately involved the design and application of Crux Subsurface Inc.’s patented steel micropile cap at 234 tower locations. This was the inaugural application of the technology, and a significant component to ensuring a successful project outcome. Foundation ChallengesThe alignment crossed a number of protected environments, including National Forest land, critical habitat for bald eagles and Peninsular big horn sheep, and numerous private properties. As a result of the remote, rugged terrain, it was initially determined that 75 lattice tower locations would not permit road construction access and would require helicopter-only construction techniques. A strict in-service date combined with long permitting lead times eventually increased this number to 234 sites. Preconstruction access constraints prohibited site-specific geotechnical sampling, so initial foundation designs were completed using only available seismic geophysical surveying and preliminary mapping data. The combination of these challenges required a foundation alternative that could accommodate variable subsurface conditions, required a minimal environmental footprint for installation, and featured lightweight materials and equipment that could be transported by helicopter."

Jan 1, 2014

By William Gleason

"What will the mine of the future look like? Will it resemble the current operations that supply the world with the products it needs to function, or will it be something totally different? How will the demands from the communities that are most affected by mining operations shape the mine of the future? How will technology and innovation be used to help miners reach deposits that are getting harder to access, and what are the dangers of this new world? Who will work at the mine of the future, and what will that work look like?These are questions that do not yet have definitive answers, but they are questions that need to be asked for the mining industry to move into a future that is as filled with uncertainty and challenge as it is with promise and opportunity.On Feb. 16, the 2015 SME Annual Conference and Expo and the 117th CMA National Western Mining Association conference began with a keynote address, "The mine of the future: Forecasting opportunities and challenges for the global mining industry." Panelists from five sectors of the mining industry participated in the session, which was followed by the conference and expo, that in large part, were also trying to answer the question of what the mine of the future will look like.In coming months, Mining Engineering will continue the discussions and answer some of the questions submitted by members of the 2,000-person audience during the keynote address in a monthly feature called, "Predicting the Mine of the Future," and in Thought Leaders Podcasts with the panelists and other industry experts."

Jan 1, 2014

By S. Suzuki, C. Tokoro, S. Owada, T. Sakakibara

Acid mine drainage (AMD) has been actively treated by neutralization from about 80 abandoned or closed mines in Japan. More efficient and cost effective treatment processes has been demanded for AMD due to the government investment of billions of yen every year to protect the environment from these discharges. In this study, quantitative modeling was conducted for actual AMD to predict pH or residual concentration of toxic elements after neutralization/co-precipitation process. Simple chemical equilibrium calculation was not adequate for quantitative prediction of pH after neutralization, because residual concentration of major elements of AMD, such as Fe or Si, could not be quantitatively calculated. When oxidation rate of Fe(II) to Fe(III) and precipitation rate of kaolinite were added to the model, quantitative prediction of pH and Fe or Si concentration was achieved. Surface complexation at the interface between hydroxide such as ferrihydrite or aluminum hydroxide and AMD was the most important mechanism for removal of dilute toxic ions. When surface complexation model at the interface of ferrihydrite was added to the model, residual As (V) and Pb (II) concentration after neutralization/coprecipitation process was successfully calculated. On the other hand, surface complezation model of aluminum hydroxide was also necessary for quantitative prediction of residual Zn(II) concentration after neutralization/co-precipitation process.

Jan 1, 2014

By D. Z. Wang

A red copper plate, discovered in the ruins of Dachengshan in Hebei province, was recognized as a forged one rather than a cast one, which means it was probably made from natural copper during the Longshan Culture period (2200~2208 BC) in the Chinese history. The copperware, found in the Niangniang Tai relics in Wuwei city, Gansu province, contains 99.6% copper and 0.4% Sn, Pb, Sb and Ni, which was guessed to be made during the Qijia Culture about 2000~ 1900 BC in the Chinese history in the late Neolithic before Shang dynasty. This shows that Chinese ancestors were able to distinguish, sort and use some native metals and minerals more than 4000 years ago.

Jan 1, 2014

By Hakan Gürsoy, Kemal Bilir, Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"Jet diffuser flotation column (JDFC) is a flotation device resembles Jameson flotation cell (JFC) in terms of operational principles, but it has significant difference structural points of view. This difference is an essential change in the downcomer to provide an increase of performance of the cell for the coarse particles. By using the hydrodynamic and fluid mechanics principles (Sahbaz et al., 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogeneous dissipation of the bubbles in the separation tank. According to experimental results carried out in pilot scale JDFC, not only higher flotation performance comparing with Jameson cell was obtained specifically for coarse talc particles in a certain condition, but also quiescent froth layer was acquired. In these tests, vertical pipe of JDFC having inlet diameter of 6 cm and outlet diameter of 11.5 cm was used with separation tank having the diameter of 39 cm. By using the data, pilot scale JDFC having 410 cm vertical pipe integrated with separation tank was produced and flotation tests were carried out by using the naturally hydrophobic mineral (talc). Finally, the talc recovery obtained as 94% by the use of JDFC, while Jameson cell has the recovery of 77% for the particle size of 250 µm."

Jan 1, 2014

By M. Y. Solar, W. G. Davenport

Most of the recent growth in nickel demand has been for the production of stainless steels and virtually all of it has been satisfied by new ferronickel and nickel pig iron projects. But "good" laterite resources are more and more difficult to find: Ni grades are decreasing while Fe contents are increasing and SiO2/MgO ratios vary from 1 to 3 and even higher if limonites are included. Predicting the smelting behaviour of such ores requires a more fundamental understanding of the thermodynamics of these systems in commercial operations. One valid question is thus whether these furnaces are at thermodynamic equilibrium or not. The present paper investigates this question, compares calculated and measured O2 partial pressures and mechanical/chemical slag loss ratios and concludes that ferronickel furnaces are not at thermodynamic equilibrium. This departure from expectation is actually to the operators’ advantage: the targeted ferronickel grades can be obtained at lower reduction potentials than calculated from pure thermodynamics.

Jan 1, 2014

By Xingming Zhang, Huawei Zhang, Yanxiang Li

"A hybrid porous metal with nano-micro double scale pore size and regular-random bimodal porous structure has been fabricated by unidirectional solidification of a lotus-type alloy followed by dealloying treatment to the base alloy. The base alloy selected is a Cu-Mn binary alloy. The lotus-type porous Cu-Mn alloy with straight pores of several hundred micrometers in diameter was manufactured by unidirectional solidification with a mould casting process. Dealloying treatment was then done to the lotus-type porous structure of Cu-Mn alloy. The solid Cu-Mn alloy wall of the lotus-type porous structure was transformed to random porous structure of dozens to hundreds nanometers. The influence of corrosion parameters, such as the current and time in electrochemical corrosion, temperature and corrosion agent in chemical corrosion, on the nano-porous structure formed has been studied systematically.1. IntroductionA hybrid porous metal is a kind of cellular structure with different porous or cellular forms inside, which possesses special properties and can be applied in many fields as fuel cells, catalysis, sensors, etc. Several means have been developed to fabricate this kind of porous material [1-2]. In this paper, a novel process of Gasar plus dealloying is introduced to fabricate a new form of hybrid porous metal with nano-micro double size and regular-random bimodal structure.The Gasar process, also called the metal-gas eutectic directional solidification, that invented by Shapovalov [3] in Ukraine and now in USA some twenty years ago, is used to fabricate porous metals with regularly aligned pores basing on the solubility difference of a gaseous element in solid and liquid metal. Nakajima and his colleagues [4] in Japan studied this process further and called this kind of structure a lotus-type porous metal. They put more attention to various fabrication techniques and properties of lotus-type porous metals. Li heading a group [5-6] in P.R. China studied the mechanism of Gasar process and process controlling techniques. The Gasar pore structure and porosity can be controlled by processing parameters, and a regular Gasar structure with oriented pores distributing uniformly in the solid matrix can be obtained under optimized processing parameters."

Jan 1, 2014

By V. Vogt

During the phosphating of car bodies containing aluminium, the employed phosphating chemicals zinc, manganese and nickel are, for thermodynamic reasons, only used to a limited extent for the desired surface coating. The major proportion of these metals is discharged together with the incidental cryolite-containing phosphating sludges and the rinse water. Commissioned by the German Federal Ministry of Education and Research (BMBF), the Institute of Mineral and Waste Processing, Waste Disposal and Geomechanics at the Clausthal University of Technology has developed a two-stage process for the production-integrated recovery of the dragged out chemicals and for closing the rinse water cycle for Audi AG. During the first stage, the phosphating chemicals are recovered by means of leaching. In the second stage, the rinse water is treated by means of electroflotation followed by an ion exchanger.

Jan 1, 2014