Search Documents

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields and rapid depletion of existing reserves emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry to meet increasing market demands, but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields" Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most of the operations are of the pressure-maintenance type} in which the reservoir pressure is maintained or partly maintained by injecting natural gas to increase oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes gas and water-injection projects in California.

Jan 1, 1952

By H. P. Willard, R. W. Gates

Basic Inc., has been mining magnesite and brucite for 27 years at Gabbs, Nev. This is a medium sized open-pit mine. The magnesite deposits are in north-western Nye County about 30 miles east of Luning, Nev., on the west slope of the Paradise Range, at an elevation between 5000 and 6000 ft. The magnesite and associated brucite is used to make magnesia refractories employed principally in the steel industry and magnesium oxide for various chemical uses.

Jan 10, 1963

By W. D. Bachman

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from Kennecott Copper Corporation's Chino mine. The efficiency with which the various samples could be ground was found to vary over an extremely wide range, even among samples taken from different locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale non-homogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully.

Jan 1, 1970

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ? Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions ? became the post-event conditions.Search for evidence that either denies or supports the various ? hypotheses.Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By D. Nutakor

The ability of computers to create synthetic representations of the real world in virtual reality offers a number of opportunities to enhance training methods used in the mining industry. Unfortunately, the training effectiveness of virtual reality systems currently used in the mining industry has received only limited testing. Miner Simulation (MinerSIM), an augmented reality system with integrated hypermedia suitable for training underground miners in the basics of using a jackleg drill to install rock bolts in a virtual mine environment is in its evaluation process at the University of Missouri-Rolla Experimental Mine. This paper discusses evaluation methodologies of the MinerSIM system, which consists of experimental and control groups with control students learning via traditional lecture and text formats. Preliminary results from usability tests of the first part of MinerSim, which is an online tutorial on underground rock bolting, are presented.

Jan 1, 2008

By C. S. Maggs, L. Shwydiuk, H. W. Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomical. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

Jan 1, 2003

By Bill Mercer

The Triggers for PDAC Involvement in H&S ??Increase in serious accidents in mineral exploration in past few years ??Increasing junior role in exploration ?? Impression that there were few H&S protocols in place in smaller companies ??Lack of national benchmarking ?? The attitude that H&S is a provincial responsibility ??Corporate Social Responsibility initiative What is the issue in exploration? ??Mining?s reputation as ?dirty and dangerous? ??In public?s and media?s minds exploration employees are ?miners? ??In Canada, regulators often do not distinguish between ?exploration? and ?mining?. ??How does exploration compare to mining from a H&S point of view?

May 1, 2008

The New Zealand Minerals Industry is small but growing. Over the next 10 years it will be facing stiff international competition for skills to support this growth, particularly from Australia who are forecasting that a further 70 000 people will be employed by 2015.   The value of commodities mined and quarried in NZ continues to increase; and the value of coal, metals and industrial minerals production reached $1.505 billion in 2006, an increase of 15 per cent on 2005. Production increases will continue à. Latest Crown Minerals statistics show that national prospecting and exploration expenditure rose to $29.9 million in the year ended March 31 2006 û an increase of 46 per cent from the $20.4 million spent in the March 2005 year. The equivalent 2001 year expenditure was only $2.48 million.   The industry already experiences difficulty in recruiting the people it needs with ongoing demand for skilled underground miners, trades people, and mining professionals. This discussion paper will outline the national context with regard to labour, skills and training. It will suggest options and provide an opportunity for conference participants to discuss the way forward.

Jan 1, 2007

By Fred D. DeVanery

"INTRODUCTION Although galena is the most common lead-bearing mineral, is easily concentrated by gravity methods, and is readily susceptible to flotation, nevertheless some galena-bearing orebodies have within them small deposits of lead ore that fail to give a high recovery when treated by the customary milling methods.The secondary minerals, cerussite and anglesite, which result from natural oxidation of galena, cause losses when the customary method of lead-ore concentration is practiced. The identification of oxidized lead-ore minerals and the efficient concentration of a lead ore taken from the oxidized portion of an orebody which has previously yielded poor recoveries mere the objects of a recent investigation. Thus the ore examined was selected from a large orebody. The work was undertaken at the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo.DESCRIPTION OF OREThe ore was of a brownish color owing to oxidation of some of the iron minerals to limonite. The lead content was 6.80 percent, and a cursory examination showed that most of the lead was present as galena. Small amounts of sphalerite, siderite, and pyrite were readily identified. The chief gangue mineral was dolomite, accompanied by smaller amounts of calcite and glauconite."

Jun 1, 1933

By William R. Yernberg

The 2006 North American Tunneling (NAT) Conference was held June 10-15, 2006, in Chicago, IL. The biennial conference was the first NAT conference by the newly formed Underground Construction Association of SME (UCA of SME). The UCA of SME was formed earlier this year at the request of members of the American Underground Association (AUA) (ME, April 2006, page 75). The conference included a keynote session, technical programs, workshops, a trade show and social activities. The conference exceeded expectations with 570 attendees. They included engineers, equipment manufacturers, representatives from government agencies and other interested individuals in the underground construction industry. The trade show was also a success with more than 86 booth spaces sold. Vendors included the biggest names in the underground construction and tunneling industry and included equipment manufactures, construction contractors and engineering companies. The trade exhibition provided a forum for interested parties in the tunneling industry to meet and discuss services, equipment and techniques.

Jan 1, 2006

By Todd Wanless

This paper addresses the challenges experienced by the designer and three government agencies during implementation of major improvements for the Turkey Creek Tunnel in Kansas City, Kansas. The tunnel serves as a vital stormwater conveyance system for upstream flood control. Major structural deficiencies were identified within the tunnel including complete loss of sidewall and invert. Without immediate attention, complete loss of the tunnel arch could lead to blockage and extensive remedial repairs under difficult conditions. Considering that tunnel flows must be maintained during construction, a phased design and construction process has been implemented to expedite stabilization of the erosion cavities followed by tunnel liner repairs.

Jan 1, 2008

By J. A. Flinn

Phelps Dodge’s Morenci copper mine has had six drills, six track-dozers, 16 shovels, two loaders, and 90 haul trucks equipped with either Caterpillar, Aquila, or Modular GPS systems for nearly three years. The Caterpillar Computer-Aided Earthmoving System is an open-architecture system, which allows for inputs to enhance orientation solutions and system functionality. This system has begun a new phase that leads to an intelligent mining system. Optimization techniques of the current system and inputs are reviewed. In addition, some practical issues of implementing new technology in a mining environment have been identified to aid in this new phase.

Jan 1, 2000

By A. Beitz, P. Smartt, G. Einicke, G. Rowan, P. Glynn

Coal is Australia’s highest export earner and Australia is the world’s largest exporter of coal. With coal now being extracted from deeper reserves under increased risk profile, and in the interest of aiding the stability of coal supplies, Japan is funding a number of safety projects in Australia and China. The CSIRO, Australia’s premiere research organisation with the country’s largest exploration and mining research group, are currently undertaking a jointly funded Japan-Australia safety project at Anglo Coal’s new Grasstree Colliery in central Queensland. The project, entitled Mine Communication and Information for Real-time Risk Analysis, will deliver step-change capabilities in data integration, decision support, gas monitoring, geo-technical monitoring, emergency response and personnel safety to the Grasstree Colliery. Some key activities include: developing and installing underground coal mine Ethernet LAN components, real-time monitoring of gas and geo-technical sensors, MODBUS serial to TCP/IP converters, e-reporting of underground conditions, emergency guidance systems and underground trials of Internet Protocol telephone and video. The project seeks to integrate (in real time) key data sets from the comprehensive and diversified range of propriety system currently in use at mines (ventilation, strata, operations e.g. haulage, pumps, conveyors etc) into a single integrated risk management interface. This interface will filter the data through a rules-based inference engine that will cross reference the various data streams, compare with past events and outcomes associated with the similar historical data and present this “intelligence” to

Jan 1, 2003

Planning for the Macraes Extension project highlighted the need for additional tailings storage availability. The possible solution of developing new tailings impoundments in Northern Gully, in tum, led to concerns being expressed by the regUlatory authority over the assimilative capacity of Deepdell Creek. Philosophical differences over the appropriateness of applying a seepage model used to set standards in consents for the original project resulted in the company re-evaluating the whole monitoring system associated with tailings disposal and seepage control. Re-evaluation indicated problems arising from the existing in-stream water quality monitoring in respect of protection of the aquatic ecological system and verifiability of results. A new monitoring system was designed relocating the compliance monitoring point out of the stream and into the gully containing the tailings impoundments giving greater certainty of monitoring results to all parties and providing improved protection for the aquatic ecology of Deepdell Creek.

Jan 1, 1993

It is well known that the electrochemical precipitation of metals from aqueous solutions is conducted by the electrochemical standard potential scale. This scale indicates the order of nobility of different metals. Consequently, the standard potential scale shows the nocivity of metals when they are present as impurities in aqueous solutions containing metals. In the hydrometallurgy of cobalt, nickel and zinc are co-deposited during cobalt electrodeposition. Nickel has almost the same chemical, physical and electro-chemical properties as cobalt. Furthermore, the electrochemical potential of nickel is relatively higher than that of cobalt. For this reason nickel is preferentially reduced at the cathode in the presence of cobalt. The presence of small amounts of zinc in solution leads to contamination of cobalt electrowon. In spite of its lower electrochemical potential in comparison to cobalt, zinc is reduced on the cathode because of its higher hydrogen-overvoltage. But, in the hydrometallurgy of zinc, small amounts of cobalt present solution will contaminate the zinc reduced at the cathode. This is easily explained by the fact that cobalt is more electropositive than zinc. The co-deposition mechanism of sulphur at the cathode is not yet well understood. Great attention has to be paid to the mechanism of co-deposition of sulphur during cobalt electrolysis. This work aimed to investigate the influence of some parameters on the co-deposition of nickel, zinc and sulphur during cobalt electrowinning. The following parameters have been investigated: Co2+concentration in the electrolyte, current density and ammonium sulphate (NH4)2SO4additions. It has been established that important nickel, zinc and sulphur co-deposition takes place at relatively low Co2+ concentration in solution. The behaviour of these elements with regard to the cathodic phenomena has been established.

Jan 1, 2005

By Stephen R. Grano, Jon Glatthaar, Philippe Steinier, Christopher J. Greet

"The importance of the oxygen content of sulphide mineral pulps in determining which reactions occur, and their subsequent influence on flotation behaviour is grossly underestimated in most operating concentrators. While pH is routinely monitored, Eh and dissolved oxygen measurements are obtained infrequently. However, dissolved oxygen measurements in conjunction with other pulp chemical parameters (i.e. pH, Eh, and EDTA extractable metal ion analysis), can provide valuable insight into where and what type of reactions are occurring within a circuit. Unfortunately, these readings yield “instantaneous” measurements of the pulp chemical parameters.What is needed is a means of establishing how reactive a pulp is, and how this reactivity changes as components of the system are manipulated. Oxygen demand provides an opportunity to do this. Several attempts at measuring the oxygen demand of a pulp have been made in the past with varying degrees of success. Most notable among these are Noranda and BOC Gases.Learning from these experiences, Magotteaux have developed the MagO2 ® demand vessel to measure the oxygen demand of mineral pulps. This paper described the apparatus, and through a case study on Broken Hill lead/zinc ore demonstrates how the MagO2 ® demand vessel is used.INTRODUCTIONThe role of oxygen in flotation is complex. While a considerable body of work exists demonstrating the strong involvement of oxygen in the interactions between sulphide minerals and collector (Gaudin and Finkelstein, 1965; Gaudin, 1974; Woods, 1984; Laajalehto, Nowak and Suoninen, 1993), the presence of oxygen can also affect the oxidation state of sulphide and non-sulphide minerals, which can impact on their flotation behaviour. Further, sulphide mineral oxidation is related to their oxygen demand (Spira and Rosenblum, 1994)."

Jan 1, 2004

By Jim Dodd, Jim Paynter

"We would like to acknowledge the efforts of the following key people who helped to make this project a success.Ron Jung, instrumentation supervisor for the Golden Giant Mine, spent many hours reviewing process and instrument drawings, selecting instruments and providing hands on support during commissioning.Andy Keough, underground production supervisor for the Golden Giant Mine, was responsible for readying the underground distribution network for paste backfill.H.A. Simons Ltd. personnel who did an excellent job providing sound conceptual and detailed engineering.Fred Brackebusch, of Mine System Design who designed the paste backfill delivery systemPierre Lacombe, mill superintendent of the Louvicourt Mine, generously shared information and operating experience of their paste backfill plant.AbstractThroughout the 11 year history of the Golden Giant Mine, the primary backfilling method made use of consolidated rock fill. New backfill technologies have developed over recent years which now make it possible to use large quantities of fine mill tailings as backfill.In January of 1996, construction began on a new paste backfill plant at the Golden Giant Mine. Six months following, the plant was commissioned. This paper describes the design, commissioning and operational experience to date of the paste backfill plant."

Jan 1, 1997

By A. du Plessis

The study summarized in this paper focused on expanding existing South African mine closure cost calculation models to provide a new model that incorporates risks, which could have an effect on the closure costs during the life cycle of the mine. This research is important because currently there are a number of mines that do not have sufficient financial provision to close and rehabilitate the mines. The magnitude of the lack of funds could be reduced or eliminated if the closure cost calculation is done in a more risk-orientated manner. The model consists of an expansion of existing closure cost calculation models, by applying the Monte Carlo risk simulation technique to model influences of external and internal changes affecting closure costs. It is shown that the proposed risk-based model provides a way to understand better the implications of uncertainty on the closure costs.

Jan 1, 2006

By Merrill Steve, Dabrowsli Bartosz, Law Harrison, Taggart Diane, Christodoulou Lance

The capability to enhance flotation performance is a continuous pursuit in the mineral processing industry. Incremental improvements are being pursued by incorporating design changes into established flotation technologies. The industry, however, is demanding advanced technologies to perform better in terms of improved resource utilization while at the same time ensuring that power and water usage is reduced. To meet these demands, it is necessary to make a step change in the performance capability of flotation equipment.

Sep 30, 2022

By Mark S. Stagg, David E. Siskind

The mining industry occasionally blasts near pressurized transmission pipelines and has requested guidance of safe vibration levels and setback distances. the Bureau of Mines and the Indiana Department of Natural Resources cooperated with AMAX Coal Company on a study of coal mine overburden blasting. Five buried and pressurized 250-ft pipeline sections were specifically installed on the Minnehaha Mine highwall near Sullivan, IN for testing to failure. Four welded steel pipes ranging from 6- to 20- in diameter and one 8- PVC water supply pipe were monitored for vibration, strain, and internal pressure for a period of 6 months while production blasting advanced up to the pipeline field. In contrast to previous studies of small-scale blasting representing construction activities, these tests involved overburden blasts of up to 2100 lb per delay in 12-l/4-in diameter holes.

Jan 1, 1996