Search Documents

By S. F. Diehl

Drill cores from uranium roll-front deposits, hosted in lower Cretaceous strata, were examined from the proposed Dewey Burdock in-situ uranium recovery site in the northern part of the Edgemont uranium district, South Dakota. Uraninite (UO2), coffinite U(SiO4)0.9(OH)0.4, and doloresite (H8V6O16) occur as pore-occluding cements within the Fall River Formation in the Dewey area. In contrast, within the Lakota Formation in the Burdock area, uranium (with very little vanadium) is absorbed onto woody fragments and amorphous carbonaceous material in pressure-solution seams. Both areas have typical uranium roll-front mineralogy with 0.5 wt. % pyrite in the reduced solid phase and no pyrite in the oxidized solid phase. The groundwater at the ore zone is not oxygenated, so the uranium is relatively insoluble. Uranium in solution in ground waters is <10µg/L at Dewey and <22 µg/L at Burdock. Micromineralogic and geochemical data are being used to understand water/rock interactions, uranium distribution and movement, and as input factors for predictive reactive transport models.

Feb 27, 2013

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

NASA has received direction for lunar habitation beginning in 2024. Prior to then, it will be necessary to learn about how lunar soil can be used to promote civilization on the moon. Questions must be answered: ?Will it support plant life?,? ?Can it be used as a construction material?,? ?What is needed to maximize health and safety?,? and ?Will it affect equipment, tools, machinery, and clothes?? The only samples available for study came from the Apollo Missions. Because the expense of bringing more material back to Earth is prohibitive, there is not enough available to perform studies to answer the above questions. Hence, there is a great need for its synthesis. Most efforts to date have concentrated on making ?simulant? from single natural resources of volcanic rock. However, another possibility is to use resources here on Earth to extract the minerals of interest into concentrates or so-called ?separates? using traditional mineral processing techniques, and then mix the separates in appropriate ratios to simulate the lunar soil. In this paper, results from a study in which dry Road Norite outcrop and wet mill tailings from the Stillwater Mining Company?s Concentrator located near Nye, MT were examined. Of course, the in-side challenge is to make ?separates? from gangue minerals.

Jan 1, 2012

By Joan Weinberg

Real output expanded at a 3.0% rate worldwide in 1987, a slightly lower pace than the 3.2% rate in 1986. The decline was accounted for largely by slower growth in the U.S.S.R. and the East European countries, as well as in the developing countries (table 1). According to the International Monetary Fund, output of industrial countries output grew 3.1% and rose most strongly in Japan, the United Kingdom, and Canada (table 2). U.S. economic growth remained at 2.9%, the same as in 1986. Consumer and government spending declined in industrial countries, while gross fixed investment: rent increased. This increase in fixed investment expenditures could be attributed partly to lagged results of some 1986 developments: the fall in oil prices, declining interest rates, and exchange rate changes. The U.S. budget deficit, as well as the large external deficits and surpluses among major industrial countries, hindered further growth .2 A report from the Organization for Economic Cooperation and Development (OECD) indicates that the impact of the October stock market crash was short-lived because it hit economies that were growing strongly, anyway.3 The growth of output in the developing countries slowed in 1987; however, output declined in the fuel-exporting developing countries. These countries have been adversely affected by weakness in oil prices and the depreciation of the U.S. dollar. The weighted average of inflation rates in industrial countries--as measured by the [ ] GNP deflator, was 2.9% in 1987, down from 3.4% in 1986. Prices rose 3.0% in the United States, up from 2.6% the previous year. Inflation for 1988 is expected to remain slightly higher in the United States than in Japan and the Federal Republic of Germany because of recent exchange rates changes and the elimination of slack productive capacity and labor in the U.S. economy. Prices in developing countries as a whole rose more than 10 percentage points in 1987. Higher import prices, caused by

Jan 1, 1988

By J. E. Sepulveda, R. Morrow

"In full scale mineral grinding operations, the steel balls normally utilized as auxiliary grinding media get to be consumed at different specific rates, as determined by 3 basic mechanisms: abrasion/corrosion (wear), impact ball breakage and impact surface spalling, the latter relating to the removal of rather small pieces of steel coming off the exposed surface of the balls due to repetitive impact with other balls in the charge or the surrounding mill liners. In conventional ball milling applications, the clearly predominant mechanism is gradual wear by abrasion/corrosion. In the case of SAG mills, where the make-up balls may be as large as 6”f diameter, breakage and spalling mechanisms are significant contributors to total ball consumption, although not to the extent of overriding wear mechanisms.Ball wear has been well characterized by the Linear Wear Theory, as presented at the last CMP 2014. Impact breakage has been customarily monitored, at the ball manufacturing site, via Drop Ball Tests (DBT) consisting of repeatedly dropping balls from a standard height and accounting for the number of broken balls and the weight loss (spalling) of the remaining unbroken balls. When properly conducted, DBT’s should provide meaningful indications of the breakage and spalling resistance of large diameter balls. The current publication is focused on the interpretation and projection of DBT results to full industrial scale, taking into account all 3 mechanisms of grinding media consumption in SAG mills.INTRODUCTIONA thorough, quantitative understanding of the independent contribution of all active grinding media consumption mechanisms is of the highest practical relevance, particularly in semiautogenous (SAG) milling operations where ball breakage and spalling can not be ignored or neglected, as it has been normally acceptable for conventional ball milling processes. The high severity impact conditions currently imposed in typical SAG mill environments create serious challenges to the manufacturers and suppliers of large diameter (5”–6”) SAG balls, whose products must be capable of surviving such harsh operational conditions with minimum breakage or spalling."

Jan 1, 2015

By I Coombes, M Trim, Y Sun, M McRae, A Spiegl, H Lagger, A Amon, P Barraclough, M Villeneuve

The Brisbane Airport Link Project (AirportlinkM7) includes the design and construction of more than 12.5 km of tunnels, with the Kedron interchange including four ramp tunnels that intersect with mainline tunnels and result in caverns with spans of up to 26 m. These caverns are in highly variable ground conditions with less than 35 m of cover underlying residential neighbourhoods and commercial properties. The Kedron caverns were constructed using the sequential excavation method (SEM). Owing to complex geometry and excavation sequence, the caverns were designed based on numerical modelling methods, including both two- and three-dimensional models. These numerical methods were used to develop a suite of support types with excavation sequences for the expected range of ground conditions. A combination of methods that included in-tunnel monitoring (convergence monitoring and extensometers), probe holes, endoscope probes, face mapping and ground settlement measurements were used to verify performance of the tunnel support systems and to select and refine the appropriate support system for each section of the caverns. The construction monitoring data indicated that numerical modelling can provide a good basis for predicting the performance of large-span underground openings in highly variable ground conditions. This paper presents a comparison of the performance of the caverns predicted by state-of-the-art numerical models and the actual measured performance.CITATION:McRae, M, Villeneuve, M, Trim, M, Sun, Y, Barraclough, P, Spiegl, A, Amon, A, Lagger, H and Coombes, I, 2014. Brisbane Airport Link Project – design and construction of the 26 m span Kedron Caverns: comparing monitoring data with the design, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Etsuro Shibata

The saturated solubility of chromium oxide and the valence of chromium in the slag are important matters when considering how to effectively utilize chromium-containing slags. The experimental data of various types of slags cited in the literature were arranged according to the optical basicity in order to evaluate the effects of the oxygen potential and the slag composition. The saturated solubility of chromium oxide and the Cr2+/ Cr3+ ratio tend to decrease with the increase of the optical basicity of the slag at an oxygen potential below 10.5 atm. However, at an oxygen potential of 0.21 atm, the saturated solubility and the Cr6+/Cr3+ ratio tend to increase with an increase of the optical basicity. A practical approach was suggested to reduce chromium in the stainless steel slag and simultaneously recover it as a ferroalloy by the direct smelting reduction of chromium oxide in the molten slag using some reductant in a small furnace.

Jan 1, 2003

By Nikolas Schmitz

For today’s construction industry, large-diameter piles are common practice, as they are more competitive than drilling a larger number of smaller piles. More and more piles are installed by drilling rigs, replacing the installation by hammer, vibrators or caisson. Equipment capabilities and technics with rotary drill rigs are highly developed, but very costly and time-consuming when it comes to rock drilling, large diameters and deep foundations. Pile top drill rigs (PBA), based on reverse circulation drilling (RCD) technology, overcome these challenges and are an efficient solution for large diameter drilling (0.6 m to 8.0 m/19.7 ft to 26.3 ft) and drilling depths of up to 500 m (1,640 ft.)in various geological conditions onshore and offshore. The paper will explain benefits of RCD technology and prove this with figures from the Mumbai Trans Harbour Link project.

Nov 1, 2022

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003

By J. M. Stuve

The present Bureau of Mines investigation measured low-temperature heat capacities of NiBr2 (8 to 302 K) and NiS04 (9 to 70 K) by adiabatic calorimetry. The standard entropies (S°, 298.15 K) of NiBr2 and NiS04 were calculated as 29.26 ± 0.06 cal/deg mole and 24.21 0.04 cal/deg mole, respectively. (1 cal = 4.1840 joules.) Heat-of-solution measurements of anhydrous NiBr2 were used to determine its enthalpy of formation (?Hf°, 298.15 K) as -50.64 ± 0.31 kcal/mole. High-temperature enthalpies of NiBr2 and NiS04 were measured by drop calorimetry to 1,150 K and 1,002 K, respectively. Enthalpies, heat capacities, and related formation functions are tabulated to 1,200 K.

Jan 1, 1978

By Keith Merriam, Jim McDonnell, Peter Radziszewski, Rob Rotzinger, Ian DeHart

"Taseko Mines Limited Gibraltar copper-molybdenum mine recommenced operation in 2004 with the initiation of a series of development projects to increase throughput capacity as well as modernize the mine.In the second staged development project, a VTM-1250-WB regrind mill was selected to replace the existing conventional ball regrind mill to achieve a target grind size of 80 % passing 45 µm. In the third staged development project, a second VTM-1250 regrind mill was selected for installation in Concentrator #2, to match the existing Concentrator #1 Vertimill. This resulted in approximately 25% spare regrind capacity in the Concentrator #2 design, complete spare parts interchangeability and potential future expansion capacity to 50,000 t/d with no circuit upgrades.In this context, a study was initiated to assess not only the performance of a Vertimill grinding circuit processing a copper concentrate to a particle size of 80% passing 17 µm but also to provide Taseko’s New Prosperity project specific design information for grinding to particle sizes below 80 % passing 25 µm.The objective of the work described in this presentation was to explore Vertimill ultrafine (sub 100 µm) grinding test methodologies at both the lab and pilot scales, compare the scale-up data with operational data from the VTM1250 at Gibraltar Mines and subsequently apply this information to particle sizes down to 80% passing 17 µm. The presentation will describe the results obtained preceded by a description of the Gibraltar regrind circuit historical operation and operational performance as well as a description of the Vertimill technology.INTRODUCTIONTaseko Mines Limited is a mining company headquartered in Vancouver, British Columbia, Canada. In addition to mining development projects for copper, copper-gold, gold, and niobium properties, Taseko Mines is seventy-five percent owner and the operator of the Gibraltar Mine near Williams Lake , British Columbia. Taseko Mines Limited’s Gibraltar copper-molybdenum mine recommenced operation in 2004 with the initiation of a series of development projects to increase throughput capacity as well as modernize the mine.Metso is a leading process performance provider, with customers in the mining, oil and gas, and aggregates industries. It has corporate headquarters in Helsinki Finland, offices in 50 countries and manufacturing facilities on five continents. Amongst other types of equipment and services, Metso designs and manufactures VERTIMILL® (VTM) Grinding Mills."

Jan 1, 2015

The 107th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 11 August, 2004. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: Ralph Bagirathi, Executive Member, African Mining Association Rudi Rudolph, President, Association of Mine Managers of South Africa Andrew Whibley, President, Association of Mine Resident Engineers of South Africa Dr Con Fauconnier, President, Chamber of Mines of South Africa Nxolisi Diliza, Chief Executive Officer, Chamber of Mines of South Africa

Jan 1, 2004

By H. Kenworthy

This report concerns cooperative milling investigations of the Central mill of the Eagle-Picher Mining &. Smelting Co, The work carried on at the Central mill and the Rolla, Station shows that: It is possible to reduce the Central mill heavy-medium plant tailings by 0.05 to .15 percent zinc; the 3/16-inch to 10-mesh fraction of the jig feed can be treated by sink-float to obtain a tailing containing only half as much zinc as the jig tailing; Humphreys spiral concentration of the flotation tailing does not recover enough zinc to be economically attractive; and crushing and wet grinding of ferrosilicon for heavy medium are commercially feasible. The Eagle-Picher Co. operates extensive mines in the Tri-State area of Missouri, Kansas, and Oklahoma. The ore is milled at its Central hill, which also accepts custom ores. During the recent war the mill handled about 12,-000 tong- of low-grade ore per day. The company milled about 50 percent of the district tonnage and purchased nearly 90 percent of the custom ore. About 50 percent of the mill feed was from company mines. Zinc is the chief value in the Tri-State ores,-with Varying quantities of lead and cadmium minerals, as well as small amounts of germanium and gallium.

Jan 1, 1949

By J. P. Mogan, E. D. Dainty, A. Lawson

"The toxicity reduction of emissions from two diesel engines by the emulsification of water into fuel oil was investigated to determine the applicability of such systems to underground mining machinery. . The engines studied were: 1) the Deut; F6L7J4, four-stroke, air-cooled, 6-cylinder, V-configuration, indirect-injection (IDl) engine, and 2) the Detroit Deisel Allison Division 8V7JN, two-stroke, water-cooled, 8-cylinder, V-configuration, direct-injection (Dl) engine.The application of emulsified fuel treatment to the two-stroke engine did not prove to be practicable. In the case of the Deutz engine, however, substantial benefit resulted. For a modest J5 per cent water content in the fuel and an injection timing of24° BTDC, approximate reductions of40 per cent in the concentrations of both particulate matter and nitric oxide (NO) were produced. These reductions were accompanied by insignificant changes in other toxic constituents. The net result was an approximate 30 per cent reduction in the over-all exhaust toxicity for typical LHD operation as assessed by the Health Effects Index criterion. This toxicity reduction represents a significant advance from the points of view of an improved underground environment and/or reduced ventilation costs."

Jan 1, 1981

By R. R. Sayers

That the maintenance of proper air conditions is a most important factor in the control of occupational hazards is shown by the large amount of material presented each year through the technical journal's on the effects on workers of injurious dusts, gases, and variations in temperature and humidity.. SUMMARY OF RECENT LITERATURE ON EFFECTS ON WORKERS OF EXPOSURE TO DUSTS The subject of the control of dust and dust diseases continues to be a matter of serious concern in most of the industrial countries of the world, as indicated by the following summary of reports published in a number of foreign countries as well as in the United States. Australia. The Workmen's Compensation Act of 1920 for New South Wales3 provided for the promulgation of schemes for the compensation of workers dis- abled by silica or other dust. In 1924 the prevalence of silicosis and tuberculosis among Sydney stonemasons, quarrymen, sewer miners and rockchoppers was investigated by a Technical Committee of Inquiry, appointed upon the recommendation of the New South Wales Board of Trade. The findings of this committee were published by the Government in 1925. No scheme was promulgated by the Government and in 1926 the Act was amended limiting its scope to workmen disabled by disease caused by silica-dust. This was promulgated and gazetted on September 16, 1927, and applies to men working in sandstone as stonemasons, quarrymen, rockchoppers, and sewer miners in the County of Cumberland.

Feb 1, 1931

By X Zhang, B McFadzean, P E. Ngoepe, B Nemutudi, P P. Mkhonto, S Pikinini

There is still a huge challenge in efficiently recovering the arsenides minerals that are largely concentrated in the Platreef Bushveld Complex which constitutes about 21 per cent of the platinum group minerals (PGMs). Therefore new collectors are required to improve the recovery separation of hard to float minerals, in particular sperrylite. The triazine modifications are promising reagents for mineral flotation and have not been given much attention in minerals processing. The adsorption of sodium 2,6-dithio-4-butylamino-1,3,5-triazine (SDTBAT), sodium 2,6- ditrithiocarbonate-4-butylamino-1,3,5-triazine (SDTTCBAT) and sodium normal butyl xanthate (SNBX) on sperrylite (100) surface were performed to identify a well performing collector molecule. We observed that the triazine collectors preferred to bridge on surface As and Pt atoms through the S atoms. We found that the adsorption energies were in the order: SDTTCBAT > SDTBAT > SNBX, indicating that the SDTTCBAT had strong exothermic adsorption on sperrylite and pyrite. These results showed that the ditrithiocarbamate had a great influence in the adsorption strength on the sperrylite surface. Importantly it was found that the triazine collector had stronger adsorption than the xanthate, which portrayed a promising replacement of xanthate collector. These results paved a way for design of novel collector for sperrylite and other chalcogenide minerals to improve their recovery.

Aug 24, 2022

By C. E. Baltzer

This is the fourth in a series of coal technology reviews being prepared. in accordance with a recommendation voted by the Coal Division C.I.M. in session at the Jubilee Meeting, Vancouver, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review of Coal Technology for distribution among those concerned in the production and use of coal in Canada. Copies of the first review, which appeared in the November, 1948, BULLETIN, pp. 612-614, of the second review in the June, 1949, BULLETIN, pp. 272-275, and of the third review in April, 1950, BUL-LETIN, pp. 1,9?3-196 (also, respectively, in Transactions, Vol. LI, 1948, pp. 262-264 Vol. LU, 1949, pp. 117-120, and Vol: LIU, 1950, pp. 133-136), were distributed by the Dominion Coal Board and are still available on request. In this review, the first in the series in the field of combustion, development and trends during the period approximately from World War II to the present time are described and therefore the presentation is general. Later reviews will particularize developments in relation to the range of coals available in Canada.-ED. INTRODUCTION THE utilization of coal in heat and power producing equipment has become of paramount importance to the coal industry in maintaining stable and profitable markets. In the past, the chief concern was with mining, transportation, and overall supply problems, but modern conditions demand interest in and knowledge of all phases of the product, from coal in situ to its ultimate disappearance in the form of products of combustion. Even the last mentoined factor has caused complications, as is shown by current widespread activity in the field of smoke abatement

Jan 1, 1951

By J. R. Nettle

The development of a process for upgrading offgrade titanium metal by electrorefining in molten salt led to an investigation of the electrotransfer characteristics of selected metals when alloyed with the titanium to be refined. Previous tests on seven binary titanium alloys showed that the degree of transfer of the alloying constituent depends on the constituent and on the operating procedurese.5 This report describes tests on electrorefining ternary mixtures of titanium with selected metallic elements. Ten alloys were prepared from high purity titanium and 2-1/2 percent of each of the metal pairs selected from the same elements used in the binary study; manganese, vanadium, chromium, zirconium, tin, molybdenum, aluminum. Operating variables were similar to those investigated in the binary alloy study that gave minimum alloy metal transfer. The data presented indicate the transfer characteristics of the various metals and combinations tested relative to each other.

Jan 1, 1962

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979

By Carmina Quintanar, Mario Palominos

"The mining industry is currently facing significant challenges to identify and adopt sustainable collector chemistry that effectively recover value minerals in difficult-to-process low-grade resources. These are typically characterized by complex mineralogy and the presence of significant amounts of penalty gangue sulfide minerals, especially pyrit which is a challenge to separate from value minerals at many major mine operations. Three chemical strategies for dealing with gangue sulfides and penalty elements are: a) selective flotation of value minerals while rejecting penalty minerals in the whole circuit, b) rejecting penalty minerals in an appropriate part of the circuit using selective depressants, c) using a combination of selective collectors and depressants in appropriate parts of the circuit. This paper will evaluate different strategies for dealing with those penalty elements and propose the most efficient alternative. New products and application technologies have been developed in the past 25 years by Cytec for implementing these strategies as dictated by the particular needs of a given plant. However, in recognition of the growing interest in meeting the sustainability challenges, Cytec Research and Development have been focused in the development of greener products (collectors, modifiers and frothers) and processes using FLOTATION MATRIX 100TM approach used to develop the optimal collector system for each specific ore. An overview of these new developments is given in this paper using case studies of application of selective collectors and polymeric modifiers including the newer, greener chemistries."

Jan 1, 2014