Search Documents

By I. Filippova, L. Filippov

"The by-product potential of light rare-earth elements (LREE, La, Ce, Nd) and rare-metals (W, Nb, Sn) within the St Austell kaolin deposits (UK) is related to the kaolinisation process, which liberates the accessory heavy minerals of the host granite in the clay matrix and allows their separation in the waste streams. As a consequence these minerals are pre-concentrated in the micaceous residue which displays relatively high LREE content (around 170 ppm) hosted by monazite which is mainly distributed (up to 95%) in the -100 µm fraction. A combined gravity/flotation concentration flowsheet, starting with classification of the residue into 3 size fractions (+150 µm, 150-53 µm and -53µm) was developed. This study presents the results of the clay-rich -53 µm size fraction beneficiation by flotation using sodium oleate and hydroxamate as collectors.The effect of dispersant addition during de-sliming operations on flotation efficiency was also investigated. The LREE grade in the floated product obtained with sodium oleate increased from 3370 ppm to 5350 ppm and recovery from 30% to 80% with dispersant which is attributed to clay coating. Comparison of flotation performance and Falcon Ultra-Fine (UF) concentration of monazite to previous results obtained with Falcon Semi-Batch (SB) gravity concentrator on the unscreened raw residue clearly shows that flotation of the fine residue is more efficient than Falcon UF and Falcon SB. Indeed Falcon UF produced high recoveries (87-95%) but with almost no enrichment (1.3-1.4 ratios) whereas Falcon SB concentration of unscreened residue produced higher grades (up to 0.6 % LREE) but with low recoveries (17-22 %). These preliminary results show that LREE can be pre-concentrated suggesting that the micaceous residue stream (and the associated tailings dams) could be considered as a potential resource for these metals."

Jan 1, 2016

By Charles E. Semler

The possible utility of selected compositions in the systems SrO-ZrO2-MgO and SrO-ZrO2-Dolomite for commercial refractory products was confirmed in this study. Specifically the compositions of interest are located in the sub-systems SrZrO3-ZrO2-MgO and SrZrO3-ZrO2-Dolomite. Both sub-systems have regions that are not affected by hydration, but the sub-system SrZrO3-ZrO2-MgO has a larger candidate compositional region. Solid state phase relations were determined for the subject systems over the temperature range 1600°C to 1300°C, with compatibility diagrams presented for each. The systems appear to show good refractory character with no apparent low melting compositions. As the compositions of commercial interest lie mostly in the higher ZrO2 portion of each system, information is presented regarding the firing treatment required to develop stabilized cubic ZrO2. A list of suggestions for further study of these systems, to further delineate the characteristics required for possible commercial utilization, is presented.

Jan 1, 1982

Core samples, which were collected by the author from the Busang prospect, East Kalimantan, reflect a progressive evolution of a large magmatic-related hydrothermal system that is comparable to that encountered in many similar systems elsewhere in the Pacific region. The initial, localized deposition of sheeted porphyry quartz-molybdenite veins took place at high temperatures and fluid salinities, and at relatively deep levels. This was followed by an extensive phase of phyllic (sericite-quartz-pyrite ¦ tourmaline-apatite) wallrock replacement and vein formation. Propylitic (epidote-chlorite-carbonate-quartz) alteration was formed marginal to the phyllic assemblages. These porphyry-related events were centred in the Southeast Zone, and are probably associated with the emplacement of a felsic intrusion at depth. This event contributed only trace gold to the system. The early stages of hydrothermal activity were followed by an episode of quartz (¦ adularia) û carbonate û base metal sulfide veining, which was accompanied by argillic (illitic-kaolin clay) wallrock alteration. This event was sulfide-rich in the Central Zone and carbonate-dominated in the Southeast Zone. Gold mineralisation was observed in Central Zone drillcore to be associated with both sulfide, as well as carbonate, deposition. A final stage of epithermal-style quartz ¦ stibnite û realgar veins are, in the Central Zone, locally gold-bearing. The latter two events are interpreted to be associated with the late-stage exsolution of metal-bearing brines from the felsic intrusion that formed the earlier porphyry quartz-molybdenite veins and widespread phyllic-propylitic alteration.

Jan 1, 2002

By W. J. Mitchell

During the months of April and May 1992, the Phelps Dodge Hidalgo smelter underwent a major turnaround. This was the third such turnaround in the life of the facility which was commissioned in 1976. During the third furnace campaign, the smelter processed 5.2 million tons of concentrate producing 2.6 billion pounds of anode copper over a 7.5 year period. The critical path on the fifty-nine (59) day turnaround schedule was the reconstruction of the Outokumpo flash furnace which integrated some modifications with standard rebuild practices. Modifications included incorporation of horizontal cooling jackets throughout the furnace settler as well as the installation of castable refractory in the reaction and uptake shafts.

Jan 1, 1993

By J Ramezani, K Faure, N Mortimer

Western New Zealand can be regarded as a rifted continuation of eastern Australia. Detailed studies of units previously considered to have trans-Tasman correlations are being undertaken within the FRST Programme Mineral Wealth of NZ and its EEZ to test specific connections, and thus add to the exploration framework of NZ. Correlation of two major episodes of granitic magmatism are currently being investigated. These represent the oldest (mid Paleozoic) and youngest (Early Cretaceous) magmatic events that conjoined Australia and New Zealand are believed to have in common.

Jan 1, 2007

By S. Sakurai

We discuss the mechanical characteristics of underground structures that are subjected to vertical oscillations. Under such circumstances - expected when an earthquake rupture occurs very close to highly developed urban areas - the conventional seismic analysis, which mainly considers horizontal shear oscillations, may not be fully valid. Our analysis, based on the elastic wave theory, shows the effects of vertical disturbances and the generation mechanism of the unique damage patterns observed on the occasion of the 1995 Hyogo-ken Nanbu (Kobe) Earthquake. Wir diskutieren über die mechanischen Eigenschaften der unterirdischen Strukturen, die sich vertikalen Schwingungen aussetzen. Unter solchen Umständen - erwartet, wann ein Erdbebenabbruch sehr nah an hochentwickelten städtischen Bereichen geschieht - kann die herkömmliche seismische Analyse, die sich hauptsächlich horizontale Schubbewegungen überlegt, möglicherweise nicht völlig gültig sein. Unsere Analyse, basiert auf der elastischen Wellentheorie, zeigt die Effekte der vertikalen Bewegungen und den Erzeugungsmechanismus der einzigartigen Beschädigungsmuster, die anläßlich des 1995 Kobe Erdbebens beobachtet wurden. Nous discutons les caractéristiques mécaniques des structures souterraines qui s’exposent aux oscillations verticales. Dans ces conditions - s’attendent quand une rupture de tremblement de terre se produit tout près des secteurs urbains fortement développés - l’analyse séismique conventionnelle, qui considère principalement des oscillations horizontales de cisaillement, peut ne pas être entièrement efficace. Notre analyse, qui est basée sur la théorie des vagues élastiques, montre les effets des mouvements verticaux et le mécanisme de génération des modèles uniques de dommages, que nous avons observés à l’occasion du tremblement de terre 1995 de Kobe.

Jan 1, 2003

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By Henry P. Wheeler

As recently as 1915, helium was available only in very small quantities at a cost equivalent to $2,500 per cubic foot. It was a laboratory curiocity, and its properties were of interest to a limited number of scientists (11).3/ During the past 30 years, however, helium has grown from a plaything of scientists to a factor of importance in the prosecution of the recent war. Navy blimps filled with nonflammable helium proved to be more than a match for German submarines operating in the Atlantic. American bombers were able to fly unheard-of distances to drop bombs on Tokyo, Nagoya, Yokahama, and other Japanese cities because they had been made lighter with magnesium, arc-welded in a helium atmosphere. The Army utilized helium-filled radio-sonde balloons to obtain vital information concerning weather conditions affecting D-day invasions and other military maneuvers.

Jan 1, 1946

By T Davids, B J. J Botha

The presence of an extensive soft siltstone layer in the middle of the inter-burden sequence of rocks at Syferfontein Colliery in South Africa prompted tests to determine the effect of different mid-column decks of inert material in the siltstone layer. The objective was to achieve significant cost savings in explosives use whilst not degrading dragline productivity. An important factor that had to be considered was that the initiation systems available in South Africa are not accurate enough to ensure simultaneous initiation of explosives decks in a hole.

Jan 1, 1994

By K. Norris

"The Campbell mill has undergone numerous changes over the past 43 years. However the rate of change has increased significantly in the last 4 years. A new grinding circuit, carbon-in- pulp circuit, pressure oxidation plant, and column flotation circuit are all new additions. Other changes have occurred in the last 2 years including a large reduction in sodium cyanide consumption, and the introduction of a computer controlled grinding circuit. More improvements are planned in the next 2 years. Some of these improvements include the construction of an effluent treatment plant, and the replacement of filtering and Merrill-Crowe precipitation with carbon-in-leach and electrowinning.Recent changes and improvements to the Campbell mill are a commitment by Campbell mill personnel and Placer Dome Inc. to decrease operating costs, increase gold recovery and gold production, improve industrial hygiene and safety, and meet environmental compliance with current government legislation.INTRODUCTIONThe Campbell Mine has been and continues to be one of Canada's premier gold mines. Campbell Mine is 100% owned and operated by Placer Dome Incorporated. Milling of ore commenced in 1949 at a rate of 300 tons/day producing 58,000 ounces per year of gold. In 1992 Campbell Mine will mill 1340 tons/day of ore at a grade of 0.6 ounces/ton, producing 275,000 ounces of gold at a cash cost of $205.00 Cdn./ounce.This paper discusses some of the changes that have been made to the Campbell mill in the past 4 years. The flowsheet has undergone extensive changes and will continue to change rapidly in the next 2 to 3 years. A simplified flowsheet of the Campbell mill is shown in figure 1."

Jan 1, 1992

By A Takahashi, Y Uchisawa, M Hayashi, T Watanabe, M Susa

Owing to the deterioration of iron ore, the Al2O3 concentration in iron ore increases, and thus it is important to investigate the effect of increment in Al2O3 concentration on the microstructures of iron ore sinters. During the sintering process, a melt is present in the sinter for only a few minutes, and therefore the microstructure of the sinter doesn’t reach thermodynamic equilibrium. Nevertheless, the formation process of the microstructures can be interpreted and predicted to some extent from the equilibrium phase diagram. This study investigated the liquidus isotherm in the CaO-SiO2-Fe2O3- 5 mass% Al2O3 system at 1240°C in air and the phase equilibria of silico-ferrite of calcium and aluminium (denoted by SFCA) and SFCA-I by XRD (X-ray diffraction analysis) and electron probe micro analyzer (EPMA). The following results were obtained: 1. The ferrite melt region with a high Fe2O3 concentration shifts to the lower Fe2O3 side than the liquidus isotherm in the CaO-SiO2-Fe2O3 system. 2. The compositional region of SFCA extends in the CaOꞏ3Fe2O3-4CaOꞏ3SiO2 direction than the silico-ferrite of calcium (denoted by SFC) composition region with a 0 mass% Al2O3. 3. SFCA-I is observed in the present system, which suggests that the increment in the Al2O3 concentration contributes to the stability of SFCA-I. These results imply that an increment in Al2O3 concentration in iron ore leads to a decrement in the volume fraction of the bonding phase and that the fraction of the SFCA phase increases, and those of 2CaOꞏSiO2 and slag phases decrease in the bonging phase. The SFCA-I phase is also precipitated from the slag with an Al2O3 concentration around 5 mass%.

Jun 19, 2024

By Steve Kral

About 500 mineral-processing professionals from around the world gathered in San Francisco, CA in Oct. 22-27, 1995 for the XIX International Mineral Processing Congress (IMPC). Following the theme “Leading Mineral Processing into the 21st Century Through Advanced Technology,”186 speakers from 28 countries covered research and development activities and innovative processes. Subjects included comminution and simulation control, physical and chemical processing, flotation practices and fundamentals, precious metals processing and mineral waste and the environment.

Jan 1, 1996

By Y. -J. Park, K. -H. You, Y. -T. Choi, Lee. H. -W.

Many large caverns are being constructed in great depths in Korea mainly for the storage of oil and LPG. These caverns are mostly located near the port where rock conditions are reasonably good. In some instances, the horizontal stress is very high and endangers the stability of the cavern. The purpose of this study is to assess the stability of large caverns excavated in a rock mass with high horizontal stress where Ko value is close to 3. Result shows that stress exerted in the shotcrete at crown exceeds allowable value when the 3rd bench is excavated. Also found is the tensile failure of shotcrete near the boundaries between benches. In Korea werden viele grosse Kaverne fuer Aufbewahrung vom Oel und Fluessiggas in grosser Tiefe gebaut. Am Meisten befinden sich diese Kaverne in der Naehe von Haefen, wo der Fels gute Verhaeltnisse zum Bauen einer Kaverne besitzt. In einigen Faellen ist die Horizontalspannung sehr gross und dadurch wird die Stabilitaet vom Kaverne gefaerdet. Der Zweck dieser Arbeit ist die Stabilitaet des im Fels gebauten grossen Kavernes mit hoher Horiaontalspannung zu schuetzen, wo Ko-Wert sich auf 3 naehrt. Die Ergebnisse zeigen, dass die Spannung im Spritzbeton an der Krone den zulaessigen Wert ueberschreitet, wenn das dritte Bank ausgegraben wird. Im Bereich des Spritzbetons zwischen Baenke wurde das Zugversagen festgestellt. Des larges cavités nombreuses sont en train d’être construites en grand profondeur en Corée prin-cipalement pour le stocage du pétrole et LPG. Ces cavités sont pour la plupart situées près de la porte oú les conditions des roches sont résonablement bons. En quelques cas, la contrainte hori-zontale est trés haute et met en danger la stabilité de la cavité. L’objet de cet étude est d’estimer la stabilité des large cavités excavées dans une masse de roche ayant une haute contrainte horizontale oú la valeur de Ko est proche à 3. Le résultat montre que la contrainte exercée dans le shotcrete à la couronne dépasse la valeur admissible quand le troisième banc est excavé. En plus une faillite en tension du shotcrete près de la frontière entre des bancs est trouvée.

Jan 1, 2003

Distribution of Settling Velocity of Irregular Particles and its Effect on Jig Separation Efficiency

Sep 13, 2010

By G. H. Martindill

Complex chemical and physical changes occurring during carbonization result in a heterogeneous system composed of gaseous, liquid, and solid phases, whose relative proportions and chemical compositions change constantly as temperature increases. Studies in which the participating variables are isolated and controlled should be useful in formulating the mechanism of coal carbonization. The most characteristic property of a coking coal is its ability to form a plastic mass at a certain stage of the carbonization process. During this period it is believed that fluidity of the coal influences the properties of the resultant coke. This report gives results of an investigation by the Federal Bureau of Mines of the influence of the maximum fluidity attained by the charge on the physical quality of the coke or char produced. As a first approach to the problem, researchers investigated high-melting-point pitches, which are relatively simple carbonaceous materials. The plastic properties of these pitches, prepared specially for this work, varied greatly; their fluidities, as measured by the Gieseler plastometer, covered most of the fluidity range characteristic of coking coals. Blending these pitches with increasing pro-portions of fine coke progressively reduced their fluidities. Coal-pitch and coal-coke blends also were treated; their fluidities were varied by changing their blending ratios. The various blends were carbonized in a small-scale carbonizer and the resistance of the carbonized residue (char) to abrasion was determined in a small-scale tumbler test, using the Roga drum.

Jan 1, 1960

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

By H S. Smit, P Lotz

Gold mining companies who are signatories of the International Cyanide Management Code (visit www.cyanidecode.org for further information) are required to measure WAD cyanide on-line and destroy WAD cyanide in excess of specified limits. Weak acid dissociable (WAD) cyanide refers to those cyanide species liberated at a moderate pH of 4.5 such as HCN(aq) and CN-, and the majority of Zn, Cd, Cu, Ni and Ag complexes with low dissociation constants. It is potentially toxic to humans and animals. Recognising and in response to the gold mining industryÆs need for an on-line WAD cyanide measurement device, Mintek recently developed the WAD Cynoprobe. The WAD cyanide analysis technique is based on the use of a ligand exchange reagent that liberates WAD cyanide from metal-cyano complexes. The ligand exchange reaction is represented by the following chemical equation: Metal(CN)X + yLigand <-> Metal(Ligand)y + xCN- The plant filtrate is treated with a ligand exchange reagent, to liberate WAD cyanide, before measuring the free cyanide concentration via amperometry. The instrument proved to be accurate and reliable in the laboratory as well as under industrial gold plant conditions during various trials. It has gained wide-spread commercial acceptance both locally and internationally. However, itÆs recent exposure to complex ore types have called for refinements to the analysis technique. It has been further developed to improve its precision and accuracy and to remove reagent and thiosulfate interferences. Its compatibility with the most commonly used destruction oxidants has also recently been investigated. The WAD Cynoprobe may be configured to measure both free and WAD cyanide concentration. Its fast analysis time, approximately 5 min, makes it suitable for use in the control and optimisation of the cyanide destruction and recovery process. Proper oxidant dosage control and monitoring of effluent concentration levels will ultimately result in less cyanide and post-destruction salts discharged into the environment.

Jan 1, 2008

By L. C. IlsLey

"There is an old saying that ""It is too late to lock the stable after the horse is stolen"". Is not this just what is being done by many mine operators today when it comes to buying safe electrical equipment for gaseous and dusty coal mines?The ""open type"" of electrical equipment or even the ""half safe"" type represents the unlocked stable. After the mine disaster, and after men have lost their lives, the lock is put on - that is, safer equipment is installed.For example, an open type of electric coal drill was used in a gaseous mine in West Virginia, This was the probable cause of the death of 27 men. A half safe type of electric coal-cutting machine was used in a gaseous mine in Pennsylvania. This was likely the cause of the death of 36 men. An unapproved, unsafe type of flame safety lamp was used in a gaseous and dusty mine in Utah. This was the all¬eged cause of the death of 171 men. All three disasters happened within the last six months, and seem to have been avoidable if proper equipment had been used.It is understood that more rigid requirements will be enforced in West Virginia. The committee of State mine inspectors made definite recommendation for im¬proving the conditions in the given mine in Pennsylvania. The Industrial Commission of Utah have already issued new orders which will remedy the use of unsafe lamps in that State.These acts and recommendation are all good and will help prevent accidents in those States in the future. Is it not a pity that such recommendations and order were not made a little earlier before the tell of life had been exacted? Is it not a pity that other States will not take these lessons to heart and safeguard their mines before and not after disasters take place?Electric current can cause accidents in five general ways as follows: (1) By shock to persons; (2) by igniting powder; (3) by igniting gas; (4) by igniting coal dust; and (5) by setting fire to inflammable material such as timber and coal. A great many accidents from these causes are preventable if proper care is taken. Most of the accidents caused by sparks and flashes from electrical apparatus would not take place if approved electrical equipment was used. By approved equipment, the writer means equipment that has been tested and formally approved by the Bureau of Mines. So far as known, up to the present time, no disasters have been caused by sparks or flashes from equipment having the Bureau's approval."

Jul 1, 1924

By Jos. R. Guiteras

This paper has been written to describe briefly the mining and milling of gold and silver ores in the Black Canyon and neighboring mining districts in Yavapai County, Ariz. The description of present operations is the result of a 10-day visit to the region by the writer in March 1936. Acknowledgments The author is indebted to earlier writers on the geology and mining in this regions and to the mine managers and their staffs, whose courteous cooperation has made possible the assembling' of material for this paper. Individual acknowledgments are made in the text.

Jan 1, 1936

By Albert L. Toenges

The State Division of Geology Arkansas Resources and Development Commission, and the Arkansas-Oklahoma Coal, Operators Association requested assistance from the Bureau of Mines in a study of coal-mining methods and practices in .Arkansas coal mines with the objective of reducing production costs. On October 7, 1946, a joint meeting was held by representatives of the Arkansas Resources and Development Commission, approximately 30 coal-mine Operators of the Arkansas -Oklahoma Coal Operaters Association, and representatives of the Bureau of Mines. The many problems confronting the coal industry in Arkansas, including mechanical mining in thin beds, costs, labor, and working time were discussed. Following this Meeting, a joint letter from Harold B. Foxhall, State geologist, and -P. R. Stewart, commissioner, Arkansas-Oklahoma Coal Operators Association, was addressed to Dr. R. R. Sayers; former ,Director of the Bureau of Mines, requesting that mining conditions in Arkansas be studied.

Jan 1, 1949