Search Documents

By John P. McDonnell

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines, in researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road and bleeder entries in a Western U.S. coal mine. With the cooperation of industry, methods were developed to install cable supports in a tailgate and bleeder entry test area using traditional resin cartridges. Resin-grouted cable bolts were also installed and evaluated in additional longwall gate road and bleeder entry systems at the study mine. The cable-bolted areas successfully maintained roof support throughout the tailgate and bleeder entries. Cable supports replaced wood cribbing as secondary support in the bleeder entry system and minimized the use of cribbing in the longwall tailgate entries. This report describes the theory, application, and advantages of cable supports and presents mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 2010

By M. K. Sichone

Anglo Platinum?s Waterval smelting complex based in South Africa operates the Anglo Converting Process (ACP) that produces SO2 offgas. This SO2 offgas is treated in a double-contact, double-absorption acid plant allowing for conversion efficiencies higher than 99.90 %. The catalytic converter used in the acid plant to convert the SO2 to SO3 is a 4-bed reactor loaded with a combination of cesium-promoted and conventional vanadium pentoxide catalysts. In June 2008 there was a shutdown, in which one of the main activities was to screen the catalyst. Before this shutdown, the operator would control the converter pass temperatures manually, via the SCADA, especially during plant start-ups after which some of the automatic temperature controllers were used. After the shutdown, the control philosophy was revisited and all temperature controllers were put on auto mode during plant start up. Furthermore the set points of the pass inlet temperatures were reduced to maximize conversion in the first two passes. The result has been a reduction of SO2 emissions, from a daily average of 50 ? 70 ppm to as low as 20 ppm for similar sulphur dioxide and oxygen concentrations. Further work has been done to maintain high bed temperatures in the third and fourth passes at low SO2 strengths by splitting the gas stream between pass 1 and 2 thus increasing the SO2 content in the gas to pass 2. This increases the temperature of the gas exiting the second pass, which results in higher temperatures in passes 3 and 4. Comparison of the converter performance prior to and after the changes is made. The benefits of partially bypassing the first pass to increase the SO2 content in the gas to the second pass are shown. Conclusions and scope for further work have been drawn from the comparisons.

Jan 1, 2009

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025

By D. Potter

Freeport Exploration initiated regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the Republic of Indonesia in 1990 (see figure 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work which totaled 2.6 million hectares (6.4 million acres) and was subsequently awarded additional?concessions which added 1 million hectares (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments Freeport?s current land position totals l. 9 million hectares (4.7 million acres).

Jan 1, 1998

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

When selecting a solution for improving resiliency at facilities, such as airports, utility and transit sites, there are many options to protect structures and equipment against potential flooding. Each case involves an evaluation of the several key factors such as: design flood parameters, the geography and geological conditions below the site, the facility, and the layout of buildings and equipment to be protected. Upon reviewing these conditions and conducting a cost analysis of various options, the most suitable approach to protecting a facility can be determined. This paper will compare the conditions at various New York City sites, and give detail to the solutions utilized at these sites to improve resiliency and protect each facility. Flood wall types varied as did the strategies for raising critical equipment, to meet the Federal Emergency Management Agency (FEMA) and American Society of Civil Engineers (ASCE) 7 guidelines. Due to granular soil conditions, some sites may experience soil seepage below the flood wall resulting in the need for underground cut off systems. The authors will also present detail regarding the solutions used to control seepage. Various cut off systems will be discussed such as grouting and sheeting, explaining the factors that may impact the choice of systems. Another consideration in flood resiliency is the potential for a buoyancy condition on basement slabs when localized flood barriers are employed on first floor doors and windows. The authors will discuss the potential impacts of this condition on facilities and methods to mitigate this issue. 1. INTRODUCTION New York City is an urban coastal Metropolis with varied geology and low land areas. This includes but is not limited to sandy soils at Coney Island and the John F. Kennedy Airport. Soft marshes are found near Flushing Queens and LaGuardia Airport. Heavy rains and coastal storms caused disruption to daily life and heavily affected the economy of this vibrant City. For instance, in lower Manhattan business was interrupted in the Financial District. Power outage was widespread; commuter trains and subways were stopped and put out of service. Additionally, numerous residential homes were damaged in Coastal Neighborhoods such as the Far Rockaways and Staten Island. 1.1. Superstorm Sandy Flood Statistics On October 29, 2012 Superstorm Sandy impacted numerous facilities in the New York City Metro area. The resulting damage cost New York City more than $42 billion in repair costs. $33 billion was allocated to repair housing and infrastructure, and $9 billion was allocated to protect transit systems1. One of the major issues that impacted the city in terms of its preparedness was the high flood surge. The surge surpassed the former base flood elevation and reached as high as 13.88 feet (above mean lower low water - MLLW) in Battery Park at 9:24pm that evening. Tottenville, Staten Island experienced more damage where the water was recorded at +16 (North America Vertical Datum of 1988 - NAVD88), which is equivalent to 18.7 feet above MLLW (see Fig. 1). Not only was the surge at record levels, the waves in New York Harbor were also at record level where some buoy stations recorded waves of up to 32.5 feet. The City released “A Stronger, More Resilient New York” in June 2013, a plan laid out to rebuild communities impacted by Sandy and improve the resiliency of the infrastructure and buildings in New York City. Figures below help to illustrate the extent of the inundation relative to the projects being discussed.

Jan 1, 2018

By H. Richard Eisenbeis, Donna M. Watkins

Many technical professionals (tp)* desire to occupy upper level management positions. But career paths for most scientists and engineers do not extend beyond their specific disciplines. This is unfortunate. Our technical frontiers are expanding so rapdily that it is difficult, if not impossible, to make sound top management decisions without understanding the technical complexities involved. Technical professionals often are not considered for upper level management positions because they lack the managerial and interpersonal skills necessary to become successful administrators. You've heard this before, but a key component of these skills is the ability to communicate. Technical professionals are often unable to communicate as well as they should with nontechnical professionals and nonprofessionals within the organizations that employ them. Communication is important for managerial success Communication is the network of interactions whereby knowledge and understanding are conveyed from one social set to another (Flippo and Munsinger, 1982). In order to be successful, managers must not only be "good" communicators, they must be "effective" communicators as well. Good communication occurs when managers are able to formulate and transmit their messages in such a way that they are received and understood. Effective communication goes one step further: It occurs when recipients accept messages as legitimate and respond to these messages in the manner desired. Before promotion into upper level positions, managers must have developed organizational skills (planning, decision making, organizing, and controlling) and interpersonal skills (directing, influencing, and motivating). Applying these skills effectively is difficult without a highly refined ability to communicate. Effective communication, then, is basic to managerial success. Nowhere, perhaps, has the importance of being able to communicate effectively been emphasized more than in Mintzberg's landmark study of managerial roles (Mintzberg, 1973). Mintzberg's results indicate that executives typically averaged 36 written and 16 verbal contacts a day. These contacts were both important and trivial. They generally occurred in a random manner. Time spent on each varied. Scheduled meetings averaged over an hour. Desk work, telephone calls, and unscheduled meetings required an average of 15 minutes or less. Why technical professionals have difficulty communicating Three reasons why technical professionals do not communicate well are: • The work motivational patterns and personal attitudes of technical professionals are not conducive to effective communication. • Students in technical professions are not encouraged by educational institutions to develop their communication skills. • Organizations do not insist that all technical professionals be able to communicate in the language of business. The work motivational patterns of most technical professionals are indicative of internals and high achievers (Hunt, Salisbury, and Whittington, 1968). As internals, they believe they control their own destinies. As high achievers, they believe that task accomplishment is a primary indicator of success. To ensure a task is completed in the manner desired, tp's attempt to structure and define work situations so they alone are responsible for results. TPs consider the task accomplished when they, and perhaps other tp's, are satisfied with the results. From the tp's perspective, the task may have been completed. From a communication standpoint, two other factors may apply. First, solving the problem required very little interaction (and thus, communication) with others. Second, the tp's, considering the task accomplished, have little concern for how their "technical" answers will be translated to nontechnical persons needing

Jan 8, 1987

By M. C. Bétournay, J. E. Udd

"The Mining Laboratories of CANMET are the principal federal government vehicle for the delivery of mining research in Canada. With research being performed at five locations, which are mostly mining communities, the laboratories are in close proximity to the industry which they serve.The Mining Laboratories have three principal roles: (1) to support government in its development of policy; (2) to aid industry in the enhancement of productivity; and (3) to improve the health and safety of Canadians,both in the workplace in mines and around abandoned mine sites.From 1994 to 1996, CANMET’s mining research was re-focused into four programs. These are: (1) Underground Mine Environments; (2) Mine Mechanization and Automation; (3) Ground Control, and; (4) Coal Mining Health and Safety.In this paper, the authors outline the work of the Mining Laboratories and also identify the areas considered to be primary targets for future mining health and safety research in Canada."

Jan 1, 1997

By Lincoln A. Stewart

"INTRODUCTION The First Supplemental National Defense Appropriation Act, approved August, 25,, 1941, authorized the Bureau of Mines to investigate sources of raw, material for western production and appropriated funds for that purpose. Numerous iron deposits and prospects in the Western States were investigated. Among those selected for more detailed investigation were tile Apache and Chodiski deposits in Arizona.The United States Geological Survey had examined these deposits in 1929 3/ and estimated that ""the quantity of minable ore reasonably to be expected in this locality will reach 10,000,000 long tons, but it will require prospecting by core drill to demonstrate this quantity with certainty"". C. H. Johnson, a mining engineer of the Bureau of Mines, made a preliminary examination in October 1941 and proposed exploration of the Apache deposit Canyon Creek.A trench sampling project was set up, and work at the Apache deposit commenced in November 1941. Mapping, trenching, and sampling of outcrops was completed in March 1942. Trenches were laid out at approximately 200-foot intervals for about 9,200 feet along the iron outcrop east of Canyon Creek, and channel samples were taken across the iron formation. The outcrop also was explored by trenching and sampling along a 1,900-foot outcrop on the west side of Canyon Creek.The first diamond-drilling campaign at Apache was initiated in May 1942 and continued to January 1943, when work was suspended owing to depletion of funds. Six holes spaced at approximately 500-foot intervals and, 500 feet back from the outcrop on the east side of Canyon Creek were drilled through the iron formation during this period.While this drilling was in progress, the Chediski deposit was mapped, trenched, and sampled. The trenches were spaced at intervals of approximately 800 feet along 10,000 feet of the iron-ore outcrop."

Jul 1, 1947

By Richard L. Sanford

This report summarizes the results of an update on a previous Bureau of Mines grant (G0264026), and includes 5 additional years of computer pro-gram development. The directory includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various governmental agencies. References to computer applications throughout the industry are presented as well as comments on program availability. The work effort on the updated directory concentrated on programs that are available to the public and are well documented.

Jan 1, 1982

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain t did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By R. R. Sayers

The increasing use of hydrogen fluoride (annual consumption now exceeds 500,000 pounds (1)4/) directly and its occurrence as a byproduct of the utilization of fluorine compounds in the mineral industries, especially in metallurgical processes and in the refining of petroleum products, has aroused interest in its toxicity, and a brief review of the literature, with special reference to the hazard of poisoning in the mineral industries, seems to be opportune. Recently, residents in the vicinity of aluminum plants have been complaining of injury to livestock and vegetation as well as to their own health from the gases discharged into the air during operation of the plants, hydrofluoric acid gas apparently being the offender. The comparatively recent utilization of hydrofluoric acid in the alkylation process for the production of high-octane gasoline has raised the question of the hazard of poisoning in the petroleum Industry. In addition, the use of fluorine-containing refrigerants has extended the potential al exposure outside of industry (2).

Jan 1, 1945

By Wang Zhi

High-Mg-content concentrates are usually treated in Jinchuan flash smelting Furnace. Because the viscosities of high-Mg-content slag is very high, the operation of flash smelting becomes very difficult. To solve this problem, the viscosities of the semi-synthesized FeO-MgO-SiO2 slag of different compositions were measured. The results showed that when in the slag the weight percentage of MgO [w(MgO)] is 6-10%, the ratio of the weight percentage of iron to that of Si02, w(Fe)/w(Si02) is 1.1-1.4 and the temperatures are within 1473-1773K, the slag viscosities increased with the increase of W(MgO) and w(Fe)/w(SiO,). When w(Mgo)<6%, the smelting temperature should be controlled at I 300°C in order to to keep the smooth operation. When w(MgO)>10%, the temperature should be kept above I 633K. When the content of MgO is higher, a lower viscosity slag can be produced by decreasing the ratio of w(Fe)/w(SiO,). The appropriate ratio of w(Fe)/w(SiO,) for Jinchuan flash smelting furnace is about 1.2.

Jan 1, 2003

By Mohamed A. Younis, Paul J. Headland, Paul H. Madsen, Vojtech Gall

INTRODUCTION A 100 ft long, 20 ft high and 18 ft wide NATM tunnel was excavated through grouted clean sands beneath a busy city street, including a variety of existing utility lines. The new tunnel associated with a hospital expansion will serve as a pedestrian tunnel connecting a parking structure with a new hospital facility. Tunnel construction started on December 15, 2005 when drilling for the grouting program started and was completed on May 26, 2006 when the tunnel final lining was completed. The tunnel was constructed by Kiewit Construction Company as a tunnel subcontractor to The Christman Company who is constructing the hospital facility for Spectrum Health in Grand Rapids, Michigan. URS was the project designer. GallZeidler Consultants, LLC were the contractor’s NATM consultant. PROJECT DESCRIPTION The Michigan Street Pedestrian Tunnel is a component of the Michigan Street Development located along the north side of Michigan Street NE between Coit Avenue NE and North Division Avenue in the downtown area of the Grand Rapids, Michigan. The Michigan Street Development includes a parking deck and four new towers to be constructed over the proposed parking deck. The tower planned furthest east is being developed by Spectrum Health as the Lemmen-Holton Cancer Pavillion. The purpose of the pedestrian tunnel is to connect the proposed Lemmen-Holton Cancer Pavillion with the future Spectrum building to be located on the south side of Michigan Street NE. The southern end of the tunnel was constructed with a bulkhead until the future Spectrum building is constructed at which time interconnection will be required. The tunnel site plan and profile are shown in Figure 1, Site Plan, and Figure 2, Tunnel Profile. Several challenges were faced during the design and construction of the Michigan Street Pedestrian Tunnel. These challenges included compressed design and construction schedule, maintenance of traffic and protection of old underground utilities. The tunnel was being constructed as part of the Michigan Street Development and coordination with other concurrent construction activities was required. The tunnel was constructed within a specified window of time to allow other associated construction activities to take place without compromising the overall project schedule. The design started in June 2005 and construction was completed by June 2006.

Jan 1, 2007

By X. Gu

Mining operations, especially surface coal mines, have great impacts on the local ecosystem and the environment. However, it has been a common practice in mine design that the economic evaluation considers only the operating and capital costs, while the costs incurred due to ecological damage are left out. Such practice underestimates the total cost of mining and ignores the difference in ecological impacts between different mine design alternatives. With growing interest in sustainable development, the mining industry is under increasing pressure to operate not only based on economic and engineering principles but also on principles of sustainability. Therefore, estimating ecological costs of mining and considering such costs in the mine design process is an important step towards reducing ecological impacts at the design stage. The objective of this paper is to quantify the ecological costs of open pit coal mining and to demonstrate the influence of such costs on the ultimate pit design. The ecological costs of mining are estimated based on the areas and types of land damaged by mining activities and the carbon emission from energy consumption. Four major components of ecological cost are identified, namely, lost value of direct eco-services, lost value of indirect eco-services, prevention and restoration costs, and the cost of carbon emission from energy consumption. Necessary equations are given for estimating these costs. An algorithm is described for ultimate pit optimization in coal deposits with near-horizontal coal seams. A case study is presented in which the ultimate pits with and without ecological costs are optimized and compared to show the influence of ecological costs on the pit design outcome.

Aug 1, 2013

By John C. Machisak

The National Safety Competition is sponsored and conducted annually by the Bureau of Mines, U. S. Department of the Interior, to stimulate greater interest in safety in the mineral-extractive industries and to encourage the development of more effective accident-prevention programs. Since its beginning in 1925, thirty-four safety contests have been conducted. This publication reports results of the 11 annual contests for the period 1948-1958, inclusive. Mineral operations awarded the "Sentinels of Safety" trophy for the best safety record in their competitive group as well as those ranking second, third, fourth, and fifth are listed along with a summary of their achievements in preventing disabling injuries. In addition, this publication contains statistical information reflecting the disabling work-injury experience of all other mines and quarries enrolled in the annual contests. The injury statistics of these operations are arranged in the six groups of the competition and through 1955 are the only data on injury-severity at noncoal mineral operations published by the Bureau of Hines. Recognition of the National Safety Competition in promoting safety has increased steadily during its 34 years. The number of plants participating in these annual competitions increased from 210 in 1925, its first year, to a record of 675 in 1958. The expanding scope of the National Safety Competition indicates that more mines and quarries in the United States are enrolling 90 all available means to promote safety on the job will be used. Safety contests like this are generally recognized, in the field of safety promotion, as an effective way to arouse and hold the interest of employees and officials in accident-prevention programs. They tend to forge individual precautionary acts into group action centered on a common objective, such as winning the ?Sentinels of Safety? trophy.

Jan 1, 1960

By David White

This paper is the result of a comparative study of ultimate coal analyses made and published by the United States Geological Survey. This study, at first casually undertaken to devise an acceptable classification of coals based on chemical analyses, was continued in connection with a microscopic examination of a number of the coals. The initial comparisons, made from a relatively small number of analyses, not only confirmed a previous conviction that the elimina- tion of oxygen incident to the development of a coal is economically far more important than has been generally suspected, but also showed that oxygen is very nearly as harmful as ash in coal. The immediate purposes of the present study were: (a) To deter- mine more definitely, from a comparative examination of a large number of ultimate analyses, the relative importance of oxygen as an impurity in various coals; (b) to illustrate the transition between various grades of coal of similar origin-transition mainly due to progressive devolatilization, brought about more or less directly by dynamic influences; (c) to ascertain the relative proportions of oxygen, hydrogen, and carbon in coking coals, especially with refer- ence to a theory tentatively framed to explain the coking quality; and (d) to forecast the probabilities of successfully treating a large number of coals so as to render them amenable, in a softened condition, to satisfactory study under the microscope. Although the hypothesis as to coking quality finds but partial support in the chemical analyses, its consideration has led to a method of predicting from an analysis with a fair degree of certainty whether any given coal will coke by the ordinary process. The unbroken transition between coals originally similar but now classed in widely different groups, whether of the same age or of different ages, as a result of dynamochemical action, appears demonstrated by the analyses as well as by field observation. This subject will not be

Jan 1, 1911

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Mehmet Aksoy, Kagan Ozdemire

With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision. Therefore, determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. Although too many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects. This paper presents the results of ground vibration measurements carried out in Espey Open-Pit Boron (Colemanite) Mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study, ground vibration components were measured for 13 shots during bench blast optimisation studies in order to predict peak particle velocity level for this site. In blasting operations; ANFO and Powergel Magnum 600 (blasting agent), Powergel Magnum (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 4 different types vibration monitors (3 White Mini-Seis and 1 Instantel Minimate Plus Models). Then, the data pairs of scaled distance and particle velocity obtained from the 38 record events were analysed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance.

Jan 1, 2005

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

Sep 3, 2019