Search Documents

By Ebrahim Ghasemi

Problem statement: One of the most challenging safety problems in room-and-pillar coalmines is controlling roof falls during retreat mining. Roof falls not only cause both fatal and non-fatal injuries to miners, stoppages in mining operations, and equipment breakdowns, but also results in the inefficient recovery of coal reserves. Approach: Sufficient awareness of effective parameters related to roof falls is an important factor in roof control. In this study, the major contributing parameters on roof falls during retreat mining are introduced based upon experience and judgment acquired from extensive retreat mining case histories and a review of relevant literature. Key findings: The main roof fall parameters in retreat mining can be divided into three categories: geological, design, and operational. Key conclusions: The design and operational parameters can be controlled by the engineer and/or operator. By the appropriate selection of these parameters in the design and implementation stages of retreat mining, the roof fall risk can be decreased to an acceptable extent.

Jan 1, 2012

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population.

Jan 1, 1984

By Michael J. Sapko, Gregory M. Green, Kenneth L. Cashdollar

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of US coal mines. The last comprehensive survey of this type was performed in the 1920s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust. Dust samples were collected by MSHA inspectors from several mines in each of MSHA's 10 bituminous Coal Mine Safety and Health Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low-temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920s. This finer size coal dust in intake airways would require more incombustible matter to be effectively inerted than the 65% incombustible specified in current regulations.

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

China’s vibrant economic growth is built on coal, the source of two thirds of the country’s electricity. Over 95 percent of China’s coal is mined underground with the average mining depth at 410 m and in-creasing at 10 m per year; today, the deepest Chinese coal mines have exceeded 1,000 m. With increasing mining depths, there are greater challenges including increased methane emissions and spontaneous combustion. According to the government, nearly half of China’s coal mines are classified as gassy (with specific gas content at least 10 m3/mt). Coalbed methane (CBM) is a clean energy source. However, only a small percentage of the methane is captured, and the rest is vented directly to the atmosphere. This paper describes China’s CBM resource, its production and utilization.

Jan 1, 2006

By Karim El-Ouassiti, Marc Minville, Stéphane Chabot, Claude Bazin, Valérie Ouellet

"Alumina is the main source of aluminium and it is extracted almost exclusively from bauxite ores found in the Southern hemisphere. Clays are abundant minerals that contain from 15 to 40% w/w of alumina from which it can be extracted by various processes. This paper reviews the processes used for the extraction of alumina from clays and discusses results obtained with a clay sample from the Murdochville area in the Quebec Province. The application of a conventional process to this clay did not yield an acceptable recovery although smelter grade alumina was produced. A modification to the process allows increasing alumina recovery from 85% to more than 92%. The application of the improved flow sheet to other alumina carriers failed to yield comparable recovery, showing that an optimum processing path for the recovery of alumina should be found for individual clay materials.INTRODUCTIONMost of the aluminium smelters are fed with alumina extracted from bauxite found in the Southern hemisphere. Bauxite is processed by the Bayer process that uses a caustic leach of the ore. In the middle of the century, the US Bureau of mines, motivated by the fear of an alumina delivery disruption, conducted several research projects aiming at producing alumina from non bauxitic ores. These projects led to the development of various acid leaching processes (Habashi, 1993). The sulphuric and hydrochloric acid leaching processes were brought to pilot plant evaluation (Bengtson, 1979), while nitric and other leach liquors were tested in the laboratory (Phillips and Wills, 1982; Habashi, 1983). Although clays are abundant and inexpensive minerals, the studied processes remained uncompetitive with the alumina extraction from bauxite (Hudson, 1987 page 42; Peters et al., 1962) for which reserves are estimated to support alumina production for the next 50 years (Oye et al., 1999). On the other hand, the local extraction of alumina from clays could significantly reduce the transportation costs of alumina to smelters and provide an alternative source of alumina supply from the Southern hemisphere countries. Also, the extraction of secondary products for some types of clay (Nasyrov et al., 1999) containing significant amounts of potassium and sodium could provide an additional return that may improve the economics of alumina production from clays."

Jan 1, 2005

By Charles O'Connor, Ben Tisa

International Training Resources is a company consisting of personnel with extensive law enforcement and military special operations experience, The staff members are qualified to train and certify, assist and advise law enforcement officers and agencies, at any level, in critical incident policy, procedures and tactical resolutions. Successful critical incident resolution is comprised of many elements of professional skills and personnel. (Command staff, negotiators, snipers, tactical teams, uniform patrol, K-9, bomb squad, etc.) Recently, tactical teams have been developing the capability for the use of explosive methods for rapid entry into crisis locations. This document ‘will briefly describe the environment, operational issues and courses of action associated with developing a complete tactical breaching program for utilization by SWAT teams in response to operational conditions in critical incident situations. This topic is being presented to the I.S.E.E. evaluators under “Interesting Blasting Projects” and “Public Relations” categories. Tactical operations differ significantly from traditional industry practices and we appreciate the opportunity to show the industry other professional applications of explosive materials and techniques. Presently, of the few schools from which law enforcement officers can receive training with explosive breaching methods, International Training Resources is the only company currently teaching and certifying officers which has received total endorsement by the California Peace Officer’s Standards and Training Commission (P.O.S.T.) and the state blaster’s licensing commission. We have pioneered the combining of law enforcement needs and blasting industry technology to train tactical officers, nationwide, in the mission essential skills necessary for explosive breaching.

Jan 1, 2000

By Alan G. Mayton

Exposure to whole-body vibration (WBV) and the postural requirements of the job have been identified as important risk factors in the development of musculoskeletal disorders of the back among workers exposed to a vibratory environment. This paper focuses on preliminary results of WBV data collected for two groups of haulage trucks ? four older trucks from manufacturer A (MFR-A) and two newer trucks from manufacturer B (MFR-B). All of the trucks and their respective seats were considered to be in good working order during the study. Measurement periods for the truck groups had similarities, but varied from 2 to 58 minutes. Sampling times for the older trucks included a mean of 19.5 minutes and a standard deviation (STD) of 6.5 minutes compared to a mean of 40.8 minutes and a STD of 12.1 minutes for the newer trucks. Data collection coincided with the approximate delivery and first operation of the new trucks, and occurred approximately 12 months apart under similar weather and road conditions, and with the same drivers except an additional driver was included with the older trucks. Truck routes were somewhat different in that quarry production had changed location in the time between data collection activities. Overall, the results suggest that the newer trucks may provide better overall isolation to drivers/operators from WBV exposure compared to the older trucks operating at the quarry; although, this will need to be confirmed with additional measurements. Considering the higher variability and shorter sampling times for the older trucks, the results should be viewed with caution. For two of seven trials, the older trucks showed that seats amplified vibration, i.e., a transmissibility (T) >1.0. Seat T for the older trucks ranged from 0.31 to 1.17 with a mean of 0.77 and STD of 0.32. This contrasted with the newer haulage trucks where seats amplified vibration in 3 of 8 trials. In this case, T did not vary greatly and ranged from 0.87 to 1.05 with a mean of 0.97 and STD of 0.07. Regarding older trucks, in five of seven trials, the seat (output) data of weighted root-mean square (RMS) acceleration (wRMSZ) for the dominant z-axis exceeded the action level of 0.5 m/s2 action level recommended by the European Union Good Practice Guide for WBV (EUGPG) and levels exceeded the recommended exposure limit of 1.15 m/s2 in two of the seven trials. The wRMSZ values for the older trucks varied from 0.41 to 1.83 m/s2 with a mean of 0.99 and STD of 0.57. Similarly, newer trucks indicated a narrower range of wRMSZ from 0.38 to 0.95 m/s2. The mean wRMSZ was lower for the newer trucks at 0.58 m/s2 with a STD of 0.23 m/s2. Similarly, newer trucks indicated wRMSZ reached or exceeded the action level in four of eight trials. None of the trials with the new trucks showed wRMSZ levels that reached or exceeded the recommended 1.15 m/s2 exposure limit. As an indicator of driver/operator discomfort, overall weighted total RMS acceleration (vector sum) values seem to show a ?rougher? ride for the older trucks. The vector sum values for these trucks ranged widely from 0.70 to 2.59 m/s2 and, in four of seven trials, showed levels greater than 1.40 m/s2. The mean vector sum was 1.44 m/s2 with a STD of 0.75 m/s2. Comparatively, the newer trucks exhibited less variation with a range from 0.69 to 1.59 m/s2. The mean vector sum was 1.02 m/s2 with a STD of 0.35 m/s2. Vibration dose values for the dominant z-axis (VDVZ), gave a sense of vehicle jarring/jolting conditions. All trials with the older trucks were within the recommended EUGPG action level of 9.1 m/s1.75. On the other hand, in three of eight trials, both newer trucks exceeded this action level with values of 9.18, 12.58, and 13.21 m/s1.75. Neither truck group showed VDVZ that exceeded the exposure limit of 21 m/s1.75. A statistical analysis was not conducted, since the differences reported between truck groups may not be statistically significant owing to the relatively small sample size. Road conditions, changes in the truck routes, and driver/operator differences (e.g., stopping and turning) are possible factors in the higher VDV for the newer trucks.

Jan 1, 2008

There is wide agreement that sustainability has multiple dimensions, but substantially less agreement on the appropriate balance among those dimensions. This occurs because peoples’ vision of a sustainable future, their goals for sustainable development, and their objectives for resource management are reflections of their values, culture, and life experiences. Even assuming agreement about the objectives of sustainable resource management can be reached; there is still a need for policy and decision makers to choose from among alternative courses of action, each of which has its own set of impacts and outcomes. One of several tools used to compare the consequences of alternative actions is the Computable General Equilibrium (CGE) model. This paper uses CGE modeling to demonstrate how policy decisions do not take place in a vacuum and how policy-makers must be aware that there are trade-offs involved in any decision.

Jan 1, 2005

The Bibliographic Data Base contained in the present volume is the result of a literature search conducted as one task of the Bureau of Mines project concerned with research in borehole assay technology. The data base includes articles, symposia, books, corporate and government reports, patents, and other literature concerned with some aspect of borehole logging, from January 1969 through December 1975. Occasional updating to keep the data base current is anticipated. The remainder of the intro¬duction will be devoted to the explanation of the organization of each entry, along with the translation of terms and abbreviations used in the text. Each entry contains six sections. These include an ID code, a title, an author section, a source section, an abstract, and a descriptor section. The first item listed in an entry is the ID code. This serves to identify an entry. It consists of the first six characters of the first author's (or editor if no authors are involved) last name, along with the last two digits of the year of publication. A letter sometimes follows the year of publication to assure a unique alphanumeric code. For example, if an author named Wilson writes more than one piece of literature in a given year (for example, 1972), the ID code for the entries identifying these pieces of literature would be identical. Therefore, to allow for unique ID codes, the first piece would he identified as "WILSON 72,', the second piece as "WILSON 72A", the third "WILSON 72B", and so on.

Jan 1, 1976

By Dae S. Young

The paper point out a new procedure to calculate the volumetric distribution of rock fragments. The method combines the practicality of digital image processing of the rock surface with the theoretical volume calculations based on principles and laws of fractal geometry. The final volumetric distribution curve is compared with the results from traditional sieving indicating close agreement.

Jul 17, 2000

By Edward J. Chuhta, Joseph E. Chilton, Robert J. Timko

in underground mines to measure worker exposure to various gases such as methane, carbon monoxide, and nitrogen dioxide (NO2). Even in relatively small concentrations, NO2 can produce harmful side effects in underground workers. Mines using equipment powered by diesel engines, carrying out explosive blasting operations, and performing extensive arc welding and/or cutting work will have measurable quantities of NO2 released by these processes. Workers in these areas often use gas monitors to warn of excessive gas concentrations and to help them determine when to increase ventilation air that will dilute these gases, thus minimizing exposures to this gas. Portable gas monitors, used to measure NO2 levels, must be calibrated before each use. Calibration is typically performed using a small portable pressurized cylinder containing a certified gas mixture. The certified NO2 standard mixture, usually 10 ppm NO2 concentration, is diluted with either air or nitrogen gas. To determine the stability of commercially available portable gas standards, two different cylinders containing NO2 in nominal 10-ppm concentrations were examined. One cylinder was diluted in air, the other, in nitrogen. Baseline NO2 mixtures were generated using a standard liquid NO2 permeation tube operated at a constant temperature. Final dilutions of the test gas mixtures were made with air or with nitrogen using a mass flow-controlled gas dilution system. This study showed that, when a permeation-type NO2 generator is used, the electrochemical sensors in portable NO2 monitors provide identical results for gas mixtures whether they are diluted with air or with nitrogen. Two different gas monitors, one with a two-electrode sensor and one with a three-electrode sensor, were used to measure gas concentrations in the two commercially available cylinders. One month after the cylinders were delivered, the NO2-in-nitrogen cylinder, stated to contain 10 ppm NO2, measured 8.13 ppm. The NO2-in-air cylinder, also stated to hold 10 ppm NO2, measured 6.88 ppm. Therefore, before using NO2 gas cylinders to calibrate monitors, it is recommended that their concentrations be verified either by manufacturer recertification or by comparing the stated cylinder gas concentrations to a laboratory-based permeation tube-generated standard.

Dec 1, 2005

By P Bellairs

The Hamersley Province is located 1000km to the North of Perth the Capital City of Western Australia and is of major economic significance due to the mining of extensive deposits of Haematitic Iron Ore for both domestic and export use. A small but significant proportion of the waste associated with these deposits presents problems due to its ability to spontaneously combust and react with explosives resulting in premature detonations.

Jan 1, 1996

By Ronald Díaz

"Cerro Corona es un yacimiento porfiritico tipo stockwork con diferentes unidades geometalurgicas, las cuales son alteraciones producidas por una extensa familia de fallas geológicas que determinan un tipo especial demineralización. En ese sentido, a medida que la mina se va profundizando, la roca encajonante será menos alterada, así como se obtendrá una mayor dureza del mineral y los problemas asociados con el menor tonelaje de procesamiento. Por ello, el presente texto señala la optimización del procesamiento de minerales de bajo contenido de arcillas y alta dureza, así como la disminución de la malla de voladura, el incremento del factor de carga, Blending adecuado de mineral duro, la disminución del set de la chancadora, la instalación de cañones de aire en los chutes de transferencia, una mayor adición de bolas, los cambios en los diseños de linea, el control de desgaste de hidrociclones, sintonización de la lógica de control y el control supervisor del molino SAG, etc."

Sep 21, 2013

By B. Derin, T. Uzunoglu, O. Yücel

In this study, reduction behaviours of Turkish chromite concentrate (48 % Cr2O3, 13.30 % FeO, 18.33 % MgO, 12.37 % Al2O3, 5.76 % SiO2) and nickel oxide by Fe-C alloy in graphite crucible were investigated. In the first stage of experiments, steel scraps were melted in graphite crucibles and were saturated with carbon at 1600 °C and 30 min. In the second stage, mixtures of different amount of chromite concentrate, nickel oxide and flux additives (CaO,SiO2 and CaF2) were charged into the graphite crucible containing the Fe-C alloy and heated to 1600 °C for different reduction times (0-180 min) under argon gas. The highest Cr and Ni con-tents in alloys were found as 11.41 and 14.37 % and the highest Cr and Ni recoveries were found as 88 and94 %, respectively at 180 min.

Jan 1, 2007

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By R. A. Friedel

THE IMPORTANCE of infrared and ultraviolet-visible spectrometry in studies of the structure of coal and similar substances is described. Special experimental techniques have been developed for these studies. Thin sections of coal are preferred, but halide pellets are easier to prepare. Information obtained from infrared spectra on chemical functional groups has been discussed; the importance of both intensities and wavelengths of absorption bands has been emphasized. Functional groups assigned include aliphatic and aromatic CH, methylene and methyl groups, hydrogen-bonded hydroxyls, hydrogen-bonded and chelated carbonyls, phenolic structures, minerals, and aromatic structures that are benzenoid or polynuclear. Infrared studies of structures of coal extracts, distillates, and reaction products of various processes, both chemical and physical, are discussed. Coallike infrared spectra of chars of model compounds have been utilized extensively in studies of coal structure. Ultraviolet-visible absorption spectra of coals show a lack of fine structure and low spectral intensities. These results have been applied to the questions of the chemical and physical structure of coal, particularly the question of polynuclear aromaticity of coals. The color of coal is also treated. The physical-chemical origin of the color of coal may be due to free radicals, as interesting correlations of ultraviolet-visible spectra with electron paramagnetic resonance have been obtained. The optical color of coal has been explained and simulation of the color changes observed in thin sections has been carried out, The spectra and structure of coal derivatives and other carbonaceous materials are also discussed. Possible sources of error in absorption spectral measurements are pointed out. Limited measurements of the ultraviolet-visible reflectance spectra of coal are described.

Jan 1, 1967

By W. G. Bearden, G. C. Howard, J. W. Spurlock

An investigation of the factors af-fec.ting the inter-zonal flow of fluids in the casing-wellbore annrc1rt.s of an oil or gas ivell is presented Laborntory tests revealed that failure of the caring-cement bond allows communi-cation of fluid at pressure differentials near 1.000 psi. Perforating with a 11011011: carrier gun does not shatter or crack the cement sufficiently to allow communication through these cracks and does not seriously affect the casing-cement bond failure pressure. The pressure to cause communication at the casing-cement bond can he increared to 3,000 psi by. limiting pipe deformation during cementing and subsequent operations. Communication can be prevented, however. up to pressures sufficient to cause the cement to fail or the casing to col-lapse, by attaching to the casing a seal ring of deformable ruhber molded between two steel flanges. When installed, one flange is attached rigidlv to the casing to serve as back-up for the gasket While tile other flange is movable. To date, these gasket seal rings have been field-tested in 27 Wells. Althotrgh communication has been noted in two wells, inter-zonal flow has been prevented in other wells in the same area by installing more seal rings between the communicaring zones. INTRODUCTION The inter-zonal flow of fluids behind casing cemented in oil wells during normal production or stimulation operations is a major operating problem. If it cccurs during production operations. it can seriously limit the pressure to which a reservoir may be depleted without harmful invasion of unwanted fluids. If it occurs during stimulation operations, it may preclude the possibility of stimulating the desired zone. This communication can be caused by failure of the bond between the casing and cement, failure of the bond between the cement and formation, or failure of the cement itself. This paper presents the results of an investigation of factors affecting com-munication at the casing-cement bond and methods which aid in preventing it. LABORATORY INVESTIGATIONS The laboratory tests performed in this study were divided into three phases. The first phase consisted of tests to determine if perforating would shatter and crack the cement sheath so severely that communication would occur through the cement itself. The second phase consisted of tests to determine more precisely the cause for the casing-cement bond failure. The third phase consisted of tests to evaluate the effectiveness of various de-formable seals attached to the casing in preventing communication. EFFECT OF PERFORATING, The effect of perforating was invest~gated in tests performed with apparatus shown on Fig. 1. Cement was poured into the annulur space hetween 5%-in. casing and 8%-in. casing and allowed to cure for 72 hours. The apparatus was then perforated with a hollow carrier gun containing eight duPont 26-A shaped charges. Bull plugs were placed over the perforations in the 8 5/8-in. casing and hydraulic pressure was applied inside the 5 1/2i-in. casing. The pressure to cause fluid communication past the cement sheath was observed and termed the "bond failure pressure". Several different cement compositions were included in these tests, the results of which are shown in Table 1. In Tests 1 through 4 of Table 1, bond failure occurred at- the inter- .

Jan 1, 1966

By Chang-Dong Li

Cadmium ingot and nickel powder were prepared by high-temperature distillation, solvent extraction and liquid phase reducing method with spent Cd-Ni batteries as raw material. The impacts of the temperature in the distilling stage, the concentration of H2SO4 in the leaching stage, the pH value in the extracting stage and the dosage of hydrazine in the reducing stage were discussed respectively. The as- prepared samples were characterized by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic absorption spectrometry (AAS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES). The results showed that the recovering efficiencies of Cd and Ni reach 99.5% and 99.3%, and the purities of Cd ingot and nickel powder were higher than 99.90% and 99.80%, respectively.

Jan 1, 2009

By William Gleason

"It is safe to say that the coal industry, in the United States and globally, is currently suffering through one of the hardest times in its history.A perfect storm of competition, changing energy demands, politics and public perceptions have collided, inflicting significant harm to the industry that many say is irreparable. This, in turn, has led to massive job losses in some regions, heavy cuts in production and even bankruptcy filings from two of the largest coal mining companies in the nation.Cheaper natural gas can certainly take a large share of the blame for the struggle of coal, as utility companies switch from coal to natural gas for power generation. According to the U.S. Energy Information Administration (EIA) the amount of coal used for electricity generation in the United States is at a 45-year low.November 2015 marked the fifth consecutive month that natural gas was the leading source of power generation in the United States. EIA said generators produced 101,866 thousand megawatt hours (MWh) of electricity with gas in November versus just 87,789 thousand MWh with coal, the lowest monthly level since May 1980 when monthly coal use was 84,884 thousand MWh.According to Robert Godby, director of the Center for Energy Economics and Public Policy at the University of Wyoming, there are a number of factors playing a role in the decline of coal, but he points to the advances in fracking as the tipping point.“A lot of people will argue that regulation is the cause of the decline, and it has played a part, for sure, but the story of the recent past is more about what competition has done to the energy market,” Godby told Mining Engineering. “The war on coal was originally declared by natural gas in 2008.”The price of natural gas, which was at $13 per million Btu before the gas fracking boom, has fallen to as low as $1.68 in December 2015. Likewise, Godby said the cost of wind generation is now lower than the cost of generation from coal and the cost of solar generation is coming down as well. In addition to that, the demand for energy has changed in the past five years with more efficiencies in everything from building design to lightbulbs."

Jan 1, 2015