Search Documents

By T. Klemetti

Moisture deterioration of clay-rich roof rocks causes high numbers of roof falls in coal mines in humid summer months. Rocks with high moisture content are generally weaker and can further deteriorate when subjected to wetting and drying cycles. As a result, it is important to evaluate the moisture-sensitivity of roof rock prior to mining. The National Institute for Occupational Safety and Health (NIOSH) has evaluated three moisture-sensitivity index tests on roof rocks from 23 U.S. coal mines. The three tests were the University of Kentucky Weatherability test (Weatherability test), the Consol Energy Water Sensitivity test (Water Sensitivity test), and the NIOSH Immersion test (Immersion test). Of these three tests, the Weatherability and Water Sensitivity tests are more reliable in classifying the moisture-sensitivity of roof rocks. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

Lean Iron Ore Beneficiation in India

Sep 13, 2010

By Denis Thibodeau

his paper describes a study of an altered mining extraction and the resulting Rockmass response at VALE?s Creighton Mine. Typically, the deep mining zones have strict stope extraction guidelines to ensure safety and productivity; however, these guidelines offer low flexibility or few options for stope sequencing. The 402 O. B. being in a good rock mass, at moderate depth and stress regime at Creighton, offered an opportunity to drive a more flexible mining sequence with stopes and a pillar. A three-phased approach was used to mitigate risk of the mining plan: 1- Numerical modelling to fully anticipate rock mass response to the proposed mining sequences. 2- In situ seismic monitoring to collect stress and seismic activity data. 3- Analysis of the in situ data to correlate to the modelling results. The creation and the extraction of a pillar in the 402 O. B. was successfully completed. The recorded seismic activity agrees well with the numerical modelling since most of the seismic activity is localised in the hangingwall where the deviatoric stress corresponds to an early damage process. The moderate levels of deviatoric stress cause localised failure with low level of seismic activity.

May 1, 2013

By Gift Makusha, Dave Minney

Anglo Coal South Africa mines coal for both the domestic and export market using open cast and strip mining methods. To establish a mine, a process is set in place to gather ever increasing amounts of geological and metallurgical data to confirm a proven reserve. Increasingly, geotechnical data are also included in this process to confirm that reserve is easily and safely mineable. The mine design process is an iterative one using a combination of numerical modelling and empirical data to arrive at a mining layout that is both, practical, productive and safe. In South Africa it is a legal requirement to compile a code of practice to combat rock fall and slope instability accidents and these have to be revised annually, reinforcing the iterative process of continual improvement. To ensure best practise occurs, all Anglo Coal operations are subjected to annual 2nd party audits and ad hoc 3rd party audit by independent consultants. This paper attempts to explain the process described above in a concise, but understandable manner. 1.0 GEOLOGICAL SETTING The Ecca sediments date from the Permian period and the coal deposits were formed in glaciated valleys on a basement of Dolomite, Ryolite or Granophyre rock types. The sediments overlying the coal deposits are typically flat lying and multiple bedded. The sediments consist of mudstones, shales and sandstones and are generally capable of forming stable highwalls given the time that they must stand up for. Anglo Coal extracts coal from the Witbank, Highveld and Vereeniging coalfields. The Witbank coalfields contain five seams numbered from the base upwards, 1 to 5 Seam; Highveld coalfield the 2 and 4 Seam and the Vereening area the seams are described as Top, Middle and Bottom seams. Coal deposited over the basement Dolomite formation display very erratic dips, as contemporaneous subsidence occurred in some instances over sinkholes that were forming, resulting in local thickening of the coal deposit and resulting in strata that dips toward the centre of the sinkhole.

Jan 1, 2006

By Bruce Clements

The Bagdad mill, located near Bagdad, AZ, was built in 1977 with a designed mill capacity of 36.3 kt/d (40,000 stpd). An autogenous mill-ball mill crusher (ABC) grinding circuit was chosen. The original mill contained three independent grinding circuits. Each contained one 9.75m-diam x 4-m-long (32-ft-diam x 13-ft-long) fixed-speed autogenous mill, a4.7-m-diam x 6.7-m- long (15.5ft-diam x 22-ft-long) ball mill and one 2. 1-m-diam (7-ft-diam) short head cone crusher. Total installed power per grinding circuit was about 8.4 MW (11,350 hp), with 5.9 MW (8000 hp) in the autogenous mill, 2.2 MW (3000 hp) in the ball mill and 261 kW (350 hp) in the crusher (Fig. 1). The autogenous mills were designed to be able to operate semi-autogenously. However, they were never converted to semiautogenous grinding (SAG) mills. As a result of this design, only about 4.1 MW (5450 hp) of the designed power is used in the autogenous mills. The grinding circuits are closed, with 2.4 x 6 m (8 x 20 ft) double-deck vibrating screens. A series of conveyors re- turn screen oversize underneath the mill coarse ore stockpile to feed the crushers. Variable speed belts feed the crushers and control power draw. Crusher product reports directly to the tail end of the autogenous mill feed belt (Fig. 2). A magnetic sensor detects tramp iron in the autogenous mill-crusher circuit.

Jan 1, 1992

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007

By Sigmund D. Schwarz

INTRODUCTION In late 1970, an experimental geophysical program was undertaken at the Lake Huron Tunnel for the purpose of developing a geophysical technique that could be applied to determining the thickness of rock above the crown of the tunnel and identifying anomalous geologic conditions ahead of the face as the tunnel was advanced. The Lake Huron Tunnel is an 18.5 foot diameter machine bored tunnel having a total length of approximately 6 miles. The easternmost 4.5 mile section of the tunnel extends offshore beneath Lake Huron. At the time this study was started, approximately 1.5 miles of bore remained to be completed at the east end of the project. The tunnel is part of a raw water intake for the City of Detroit water supply. The Lake Huron Tunnel is bored in Antrim shale, a dense marine shale of Mississippian or Devonian age. The west end of the project encountered banded brown shale containing numerous calcareous concretions ranging in size from a few inches to more than 16 feet in diameter. As the tunnel was advanced in an easterly direction, a transition was encountered into very uniform gray shale. One set of prominent vertical joints was encountered with a strike running approximately 15 to 20 degrees askew of the tunnel axis. Bedding is essentially flat. Variable quantities of salt water and natural gas occur in the rock. The results of exploratory drilling carried out for preliminary design studies indicated that as little as 30 to 35 feet of rock cover could be expected under the lake at the east end of the project.

Jan 1, 1997

Recovery Efficiency Study on Ilesha Placer Gold Ore by Flotation Using Locally-Sourced Frothers and Collectors

Sep 13, 2010

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

By S Hapugoda, J R. Manuel, X Cao, B D. McDonald, N A. Ware, L Lu

Roy Hill is a large iron ore mining, processing, railing and port operation in the Pilbara region of Western Australia. Since delivering its first shipments to customers in December 2015, Roy Hill has quickly achieved a 60 Mtpa production rate of lump and fines products. The process plant, principally consisting of wet scrubbing, screening and de-sanding unit processes, was expanded from early 2020 to include operation of a Wet High Intensity Magnetic Separation (WHIMS) Plant. The WHIMS Plant treats tailings to recover approximately 4 Mtpa of ultra-fine (nominally -150 μm) high-grade hematitic concentrate which, after dewatering, is blended into the fines product. Unlike typical hematite concentrates, which consist largely of dense particles with smooth surfaces, the WHIMS concentrate is characterised by very finely microporous hematitic/goethitic particles, reflecting the overall characteristics of the Roy Hill deposit. Detailed test work has been conducted in collaboration with CSIRO to characterise the WHIMS concentrate in terms of its physical and mineralogical properties, and to determine its influence on the granulation and sintering performance of Roy Hill fines – from fundamental/lab-scale and sinterpot perspectives. The results demonstrate that blending of the high-grade hematitic Roy Hill WHIMS concentrate into the fines product can maintain overall sinter quality and positively influence granulation and sinter melt formation, as well as Fe grade.

Nov 8, 2021

By J. A. Beukes, M. Marais

TICOR South Africa is a new titanium feed stock producer. In the Ticor South Africa plant the ilmenite feed to the smelter plant is roasted to enhance its magnetic properties. This allows for the magnetic separation of chromite from the ilmenite. The magnetization reaction relies on partial oxidation with both under- and over-oxidation causing insufficient magnetization. To subject the roaster plant feed material to the required physical conditions a circulating fluid bed (CFB) roaster is used. This paper describes the development of a laboratory model that will aid in the control of the CFB roaster.

Jan 1, 2003

Current design guidelines for the surface catalysed oxidation of Fe(II) on Fe(OH)3 (Ochre) in passive mine water treatment systems are based largely on empirical data as the details of rates and mechanisms have not fully been revealed. Also the effects of elevated carbonate concentrations, typical of many UK minewaters, on the surface catalysed oxidation rate are unclear. In order to move away from empirical design and towards sound engineering that is based on geochemical and hydrological understanding it is necessary to quantify these reaction rates. In this study the effects of Fe(OH)3 and carbonate on the rate of Fe(II) oxidation by dissolved oxygen have been investigated with an aim to delineate the reaction mechanism. Experiments were conducted under well-controlled conditions. Preliminary results indicate that the surface catalysed reaction is an order of magnitude faster at pH ~6.4 with 200 mg/l Fe(OH)3 than the homogeneous rate and is dominated by an elevated rate of removal and oxidation of Fe(II) from the solution phase. It is also apparent that the oxidation rate of actual adsorbed Fe(II) is substantially retarded with respect to the homogeneous rate. Carbonates were not shown to affect the surface rate within the bounds of this preliminary study.

Jan 1, 2006

By A. G. Pasamehmetoglu

This paper describes the conver¬gence and load measurements carried out in inclined seams at five longwall faces, two of which were supported by hydraulic props and the other three by conventional timber supports in Karadon-Gelik mine. The minimum support capacities determined in this study are compared with the results obtained from two empirical approaches suggested by Wilson (1975) and Jacobi (1981). The characteristics of hydraulic props to be used and support patterns in the longwalls are found, conclu¬sions are drawn and suggestions are made. Design nomograms are prepared for field engineers, in order to be able to approach the problem more confidently and realistically.

Jan 1, 1992

By R. W. Schutz

"Titanium possesses an exceptional and wide-range resistance to chlorides and their compounds when compared to most corrosion-resistant engineering alloys (CRAs) used in the chemical process industry. This natural resistance to chlorides stems from titanium’s protective, tenacious, and readily rehealable titanium oxide surface film, which is chemically stable over a wide range of pH and redox potentials in aqueous environments. This passive film explains titanium’s elevated resistance to anodic pitting, crevice and stress corrosion, and erosion-corrosion in aqueous chloride environments.Guidelines for successful selection and application of industrial titanium alloys are derived from an extensive laboratory test database and more than forty years of industrial/chemical service experience. These guidelines are simplified, and alloy corrosion performance is assessed with respect to four basic aqueous chloride service categories where selection or consideration of titanium is highly merited. An overview of historical titanium alloy applications in chloride-rich environments in a wide variety of process industries substantiates their exceptional chloride tolerance. These industrial titanium alloys are cost-competitive with stainless steels and nickel alloys, readily commercially available, and routinely fabricated and welded in the shop and field via well-established methods."

Jan 1, 2002

By Brian Wingfield, Greg Williams, Richard W. Givens

Application of required energies into the rig design can have a dramatic impact upon productivity. Computer modeling of these production variables has led to changes in design with values closely approaching actual field data. Knowledge of these required energies can also specify the proper drilling technique to the application. With this knowledge, productivity-to-cost ratios can be determined with the most efficient option chosen.

Jan 1, 1995

By M. Tarvainen

"Lately, the development work in closed circuit grinding has mainly been focused on mills and on different types of instrumentation, mathematical models and automation in spite of the fact that the poor efficiency of the classifier is well known. It has also been proven by several investigations that by improving the sharpness of classifier separation, remarkable technical and economical advantages can be achieved. Some attempts to improve the performance of the most common classifier, hydrocyclone, have been made, among them injection of wash water above the spigot cyclone and retreatment of either or both of the products of the primary classifier. No method has been successful enough to achieve general adoption in the industry. The purpose of this paper is to introduce some industrial results achieved by two-stage classification where the coarse product of the turbulent-flow classifier, hydrocyclone, is cleaned in a laminar-flow cone classifier.The main target of the adoption of the two-stage classification circuit it naturally to improve the sharpness of size separation. This again leads to the following advantages in the grinding process:- lower circulating load and increased capacity- lower energy consumptionnarrower size distribution in the fine product- less overgrinding and less slimes- reduced specific surface areaThese improvements, no doubt, reflect on the subsequent concentrating process in the following aspects:the rate of flotation is improved, less reagents and energy is neededthe recovery and grade of valuable minerals in concentrates is improved- savings in dewatering can be expected- less fines in tailings improve the conditions for water recirculation."

Jan 1, 1980

By M. Buxton

"Advanced data acquisition and process modelling technology provides online data and decision support about different aspects of the resource extraction process. Real-time approaches have recently been applied to utilize the value of this information for improved production control in mineral resource extraction in different operational set ups including coal, polymetallic ore and gold deposits. The key concept of these approaches promotes the change in paradigm from discontinuous intermittent process monitoring to a continuous process and quality management system in the resource extraction process. The framework includes a real-time feedback control loop that rapidly links online material characteristics data acquired during extraction at the mining face, during material handling and processing with a sequentially up-datable resource model. This will allow near real-time optimization of decisions related to long-term planning, short-term sequencing and production control. The contribution reviews recent developments in the three main constituents sensor based material characterisation, rapid updating of grade control models and simulation based optimization for improved production control. Technological readiness is assessed and critical gaps for further technology development are identified. The value added is illustrated by means of selected case studies. INTRODUCTION With the depletion of known and established mineral reserves, the decrease in head grades and the continuing demand of mineral raw materials by the modern society, future exploitation will move towards extraction of deposits under geologically more complex conditions. Complex deposits are characterized by a low continuity in grade, presence of deleterious elements such as arsenic and high irregularity in the geometry of the ore boundaries. The profitable exploitation of such deposits becomes significantly more challenging. To be able to better utilize such unconventional mineral resources of the future, smart autonomous mining systems are needed, which integrate local exploration of spatially varying material characteristics in–situ and have the ability to follow and extract the pay zones in the ore body while minimizing dilution (Buxton and Benndorf, 2013). The main barriers to overcome for the successful economic exploitation are: • effective grade control which will maximize resource potential along the whole value chain, • minimization of handling zero-value material introduced by dilution, thus • reducing unnecessary expenditure of energy and financial resources and • management and control of the geological uncertainty due to limited information available,"

Jan 1, 2017

By A. G. Pasamehmetoglu, N. Celebi, K. Erarslan

A deposit evaluation system has been developed for a proposed new mine in the basin around Collolar in Turkey. It includes compositing, gridding and reserve estimation facilities and takes account of the economic value of the pit and the pit bottom elevation

Sep 1, 1991

By Dae-Woo Kang, Sang-Wook Kim, Shin Lee

The Air-tubes blasting method is provided in which a series of aligned boreholes are charged with explosive s and air tubes in a predetermined blasting pattern. The air tube is composed of cylindrical flexible tubes which have a predetermined width and length to be fit with the site boreholes. Within a preferred formation, each borehole is charged with the explo sives and detonators with an air tube installed just above the explosives. Stemming materials are filled above the air tubes. At the limestone mine of Sung-Shin Cement Co., in South Korea, these blasting tests were performed by a diameter 102 millimeter and 15 m long boreholes with the charging length of explosives was 8m to 10 m by the total weight of explosive 40 to 50 kg with 3m to 6m air tube which has a 76 mm diameter, and 1m to 3m stemming cover. Blasting results showed the about 10% to 30% explosives savings available and especially, the about 20% to 50% reduction of ground vibration with the low noise measures around 2dB to 5dB by this new blasting method which was compared with the conventional blasting methods. The explosives and air tubes may be alternately charged along the boreholes. The use of air tubes which were charged above an explosive layer allow to form the quantitative air decking in every blast hole. Therefore, the Air-deck effect can be easily obtained through this blasting method, and also easy to increase the fragmentation rate resulting in the more suitable mucking procedures at the working site with the minimum usages of explosives for the better economic operations in mine quarries.

Jan 1, 2005

Six pioneers of the American mining industry will be inducted into the National Mining Hall of Fame on Saturday, Sept. 13, at the Museum Convention Center in Leadville, CO. The 16th annual Mining Hall of Fame induction banquet will begin with a reception and open house at 5:30p.m., followed by the dinner and program at 7 p.m. The six inductees include James M. Gerstley, the only living member, and George O. Argall, Jr.; John F. “Leadville Johnny” Campion; Charles R. Nailler; Edwin N. Pennebaker and Russell L. Wood.

Jan 1, 2003