Search Documents

By C Chen, T Kan

The distribution ratio of Pb (LPb s/m) between three types of slags (FeOx–SiO2, CaO–FeOx and FeOx– CaO–SiO2) and molten copper after equilibrium was measured at 1300°C and oxygen partial pressure (pO2) of 10-10–10-6 atm. Results showed that for FeOx–SiO2 slag, the LPb s/m increased from 0.024 to 2.57 with pO2 increased from 10-10 to 10-6 atm. The LPb s/m with CaO–FeOx slag was lower than the FeOx–SiO2 slag at the same pO2, ranging between 0.015 and 0.53. Using the FeOx–CaO– SiO2 slag generated LPb s/m values (0.02–1.6) in between. The oxygen partial pressure in the investigated range had no obvious effect on the activity coefficient of PbO (γPbO) which was averagely 0.44, 1.70 and 0.71 for FeOx–SiO2, CaO–FeOx and FeOx–CaO–SiO2 slags, respectively. The increases in the (CaO+MgO)/SiO2 mass ratio of the FeOx–CaO–SiO2 slag induced the decrease in the LPb s/m and the increase in the γPbO value. However, the variation in the Fe/SiO2 mass ratio didn’t exert obvious effects.

Jun 19, 2024

By C. G. Maier

Relatively infrequent use by metallurgists of the term "sponge chromium" as contrasted to more than occasional reference to "sponge iron" may be ascribed to the fact that the former material is not a commercial product, while the latter has been known and used, at least in one form (Swedish sponge iron), for several decades. It is doubtful whether a true sponge chromium ever has been prepared heretofore in the laboratory by more than one or two investigators. Nature presents a much. more difficult problem to the investigator endeavoring to make sponge chromium than pertains to the production of more easily reducible elements such as iron or nickel. Recent widespread interest among metallurgists in the possibilities of powder metallurgy is ample incentive to explore the feasibility of producing pure chromium metal in finely divided form. The shift in terminology of this statement from "sponge" to the "finely divided form" is deliberate in emphasis of distinction between terms that occasionally have been used loosely. It would seem desirable that a uniform usage descriptive of finely divided metals be adopted. While to some it might seem preferable that the terra "powdered" metal be reserved for a finely divided form produced by mechanical means, as, for example, chromium produced by the mechanical comminution of electrolytic sheets or flakes, current usage of the term "powder metallurgy' involves no distinction as to source type of material. It is usually accepted, however, that a sponge metal is one reduced from oxide or other combined form at temperatures below the melting point of metal or oxide so that the particles of metal are pseudomorphic, at least macroscopically, with the source material, and, in consequence of the loss of material without change of external shape of the particles necessarily have an open, porous, or "spongy" structure.

Jan 1, 1942

This report is in partial fulfillment of Contract S0241051 awarded to COMINEC on June 27, 1974. 'Me purpose of the work under this contract is to develop a conceptual design for an automated longwall mining system. The conceptual design will serve as the basis for future design and development of an automated longwall mining system capable of sustained production in excess of 2,500 tons per shift with reduced manpower which will ultimately be demonstrated in an area where conventional longwall mining has been successful. 1.2 DEFINITION OF THE PROBLEM 1.2.1 Why An Automated System The most obvious benefit of automation and remote control in a longwall mining system is the reduction of accidents consequent upon a reduced working force in the hazardous face areas. However, another important aspect of the problem is the skilled labor shortage which is being compounded by the need for vastly increased coal production. The United States coal mining industry had a working force of almost 600,000 miners in 1928 but was able to muster only 145,000 miners in 1970. The miners required to staff the additional working sections and the new mines necessary to meet our energy needs are simply not available. Only automation and remote control will permit a reduced work force with increased production by keeping the face equipment operating continuously.

Jan 1, 1975

By Howard W. Kilau

The U.S. Bureau of Mines is investigating surfactants added to water sprays to enhance the control of dust during coal mining operations. The objective of the present work was to establish the general applicability of adding sulfate ion to anionic surfactant solutions in order to improve wetting action. This was pursued through laboratory wettability testing of four anionic surfactants and one nonionic surfactant in combination with various concentrations of sulfate ion. The experimental results demonstrated that the addition of sulfate ion enhanced the wetting characteristics of all the anionic surfactants when applied to hard-to-wet coals, while easy-to-wet coal showed more complex wetting behavior. Sulfate ion in the presence of nonionic surfactant enhanced wetting only slightly or not at all. Surface tension measurements of the dilute aqueous surfactant-sulfate anion solutions indicated this property was not important in coal-wetting phenomena, as long as the value was below the critical value for coal. Sulfate ion helps surfactant reduce surface tension but primarily appears to affect wetting action by altering the adsorption characteristics of surfactant on the coal surface.

Jan 1, 1990

By Edward P. Barrett

SPONGE IRON has been defined as the metallic product formed by the reduction (removal of combined oxygen) of iron ore or other iron oxides at temperatures below the fusion point of iron. This product probably derived the name "sponge iron" from its porous nature. When the reduction proceeds at slightly higher temperatures and the particles of metal weld together or finally even melt to yield pellets or balls that lack the porosity and low-density characteristic of sponge iron, the product might more correctly be called "direct iron."

Jan 1, 1954

By Kouichi Tomisawa

Two bridges were constructed for extension work of Central Hokkaido Connection Road in 2005 at two different sites. Pile group foundations were employed for the foundations of abutments of the two bridges. In order to assess the performance of the constructed piles in the sites and to obtain design parameters for design in future, static alternating cyclic horizontal load test was carried out on one of the open-ended steel pipe piles constructed at each site. The ground at one site was characterised as a thick deposit of volcanic soils, and the ground at the other site was characterised as a very soft peat layer near the surface. In this paper the results of static alternating cyclic horizontal load tests on the piles at the two sites are presented and discussed in detail.

Jan 1, 2006

By C. M. Keenan

During the 7-1/2 years (January 1945-June 1952), immediately preceding enactment of the Federal Coal Mine Safety Act, 26 major disasters3/ in the coal mines of the United States caused the deaths of 491 persons. In the next 7-1/2 years under the act (July 1952-December 1959), only 12 major disasters occurred. The total killed was 148. This improvement is commendable. However, the continuing frequency of minor fires and gas and/or dust ignitions in the Nation's coal mines, many of which could have been of major consequence, are cause for serious concern to the coal-mining industry and those affiliated agencies engaged in promoting safety in the industry. The data presented in this report have been prepared to make available to the coal-mining industry and related groups an overall perspective of the disaster potential from mine fires and gas and/or dust ignitions in coal mines after 7-1/2 years under the Federal Coal Mine Safety Act. This act, effective July 16, 1952, which amended the original Federal coal-mine investigative act of May 1941, provides under Title II certain enforcible mine-safety provisions designed to prevent major disasters caused by explosions, fires, inundations, and man-trip and man-hoist accidents in coal mines that employ 15 or more individuals underground.

Jan 1, 1960

By David H. Sanders, Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Large-diameter drilled shafts (DS) are a critical part of a seismic-resistant system, and therefore it is important to be able to accurately model lateral resistance. To undertake the lateral load analysis of largediameter DS, a finite-difference p-y analysis program, NVShaft, is being developed at the University of Nevada Reno. Validation of the new program involved numerous p-y analyses using commercially available programs. Subsequent comparisons suggested the program's ability to yield reasonable predictions for typical diameter DS. Based on the I-15/US 95 load test program carried out in Las Vegas, NV, this study presents the evaluation of NVShaft in Nevada’s subsurface condition. Lateral load analyses of a 2 ft and an 8 ft diameter DS were attempted using NVShaft. The location of the applied lateral loads and the presence of cemented soil-layers were incorporated in the modeling. A good agreement between NVShaft prediction and the measured response was found for the 2 ft diameter DS. For the 8 ft diameter DS, a stiffer response was predicted. The inspections of the moment-curvature characteristics at different load levels suggested cracked response of the concrete due to prior axial load testing may be one of the reasons behind the deviation.

By Michael W. Lewis

The latest downturn in the world’s metal prices has forced many mining companies to focus on cost reduction and productivity improvements to remain competitive. Maintenance represents a significant part of the overall operating costs in the mining industry. A structured, proactive maintenance approach, such as reliability-centered maintenance, can achieve cost reductions and productivity improvements. Remote condition-monitoring systems are becoming commonplace because they have the potential to identify problems before failure. Detection of equipment degradation before failure will enable repairs to be scheduled, thereby reducing costs and interruptions to production. The mining industry is in the midst of uncertain times. Decreasing commodity prices, demand, head grade and capital availability along with increasing environmental requirements have put pressure on mining companies to significantly reduce costs to maintain short- and long-term viability. Corporations are looking at expansion, merger/consolidation and financial/hedging programs to achieve these cost reductions. Mines are reducing costs by eliminating all but essential expenditures, increasing production levels, reducing overtime and investing in new technologies.

Jan 1, 2000

By Daniel H. McClain

A unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT)Center resulted in a video CD-ROM training program for new miners entering the aggregate industry. Cooperation from everyone involved, including the U.S. Mine Safety and Health Administration (MSHA),made this the product against which other training materials in the mining industry will be measured in the 21stcentury. This product’s versatility and wide application make it a tool that is as critical to a mine’s success as any earthmoving machine. The state and federal grant money involved allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2003

By Yngve Jordal, Sverker Hartwig

The IVAR Project is Norway's largest sewer project presently under construction. One part of it is an 8.1 km (26 575 ft) long, 3.5 m (11 ft 6 in.) diam tunnel, bored in one year. The tunneling project has been running smoothly; however, not everything has been easy. A few of its features are highlighted in this paper: The use of 9 0 (12 cu yd) muck cars on a double track back-up in such a comparatively narrow tunnel. Employing only four men in the tunnel, including the loco driver. A quartzite dyke - 96% quartz with 350 MPa (50 000 psi) and more compressive strength - turned out to be 640 m (2 100 ft) thick instead of the predicted 90 m (300 ft). Passing under a gaseous swamp with only same 5 m (16 ft 5 in.) of rock cover on top.

Jan 1, 1991

By L. C. Graton, Joseph Murdoch

I. Introduction......................... 26 1. The Relations of Scale in Geologic Work........ 26 2. General Characteristics of Copper Sulphide Ores..... 29 3. Scope of Present Study................. 31 11. Description of the Important Minerals............ 36 1. Pyrite....................... 36 2. Pyrrhotite....................... 41 3. Chalcopyrite...................... 41 4. Bornite........................ 40 5. Covellite....................... 50 6. Chalcocite....................... 52 7. Enargite...................... 59 8. Tetrahedrite and Tennantite.............. 61 III. Conclusions.......................... 62 I. Introduction. The Relations of Scale in Geologic Work. Many features of human accomplishment rest upon the possibility of representing natural objects on a scale of different magnitude from the actual one. Most drawings, for example, are of very different scale from that of the object depicted, and indeed are useful mainly 011 this account. More important than the question of mere convenience, however, is that of meeting the physical limitations of vision.' Thus, a mural

Jan 1, 1914

By Gary Jobson

The Mt Todd Gold mine is situated near Katherine in the Northern Territory of Australia. Commissioning of an 8 Mtpa processing facility incorporating a four stage crushing circuit, ball mills, flotation, concentrate regrinding, high rate thickening and CIL processing was commenced during late 1996. A 4.5 M tonne /annum crushing and heap leach facility was commissioned during late 1994, and was subsequently upgraded to a nominal 6 M tonne / annum circuit during 1995. Processing equipment used included primary gyratory, secondary cone and tertiary Barmac VSI crushers. Some of the features of that crushing circuit and heap leach facility were presented at the Randol Perth 95 conference by myself. The location is described as sub tropical with average climatic conditions including 1100 millimetres annual rainfall, predominantly during the December. to March wet season, and 3000 millimetres evaporation and maximum temperatures ranging from around 26 to 46 °C. The main gold occurrence at the Mt Todd site is the Batman deposit, with current published Reserves of some 60 Mt@ 1.20 g Au / tonne ( 0.0425 oz Au / ton ). The primary ore from the Batman deposit is an extremely competent greywacke and is very hard at an average Bond Ball Mill Work Index of26.5 kWhrs/ tonne. Other indicators include a Bond Impact Crush Work Index of 20 kWhrs I tonne, an Abrasion Index of 0.15 and Ultimate Compressive Strength values of 100 - 200 MPa. The main gold occurrence is very finely disseminated free gold (at an average grain size of around 5 micron) within a combination of quartz and mixed sulphide. This gold bearing component is confined to largely parallel veins ranging from 0.5 to 25mm wide within a greywacke matrix. Although the gold is essentially non­refractory, there is a strong recovery versus grindsize relationship due mainly to the liberation characteristics and the relatively low permeability of the host greywacke rock.

Jan 1, 1997

By G. H. Sedahmed, S. A. Nosier, M. H. Abdel-Aziz, A. A. Mubarak, M. A. El-Naggar, E. G. Abdel-Aziz

The performance of a rotating fixed bed reactor in recovering copper from industrial waste solutions by cementation is studied under various conditions. The rotating fixed bed is made of stacked woven steel screens to take advantage of two features of screens: the ability to present large area per unit volume and their ability to promote high turbulence. Variables studied are initial CuSO4 concentration, bed rotation speed, mesh number of the screens and bed thickness. The presence of baffles was found to increase the rate of cementation. The data were correlated by a dimensionless mass transfer correlation suitable for the design and operation of large scale cementation reactors.

By G. H. Sedahmed, S. A. Nosier, M. H. Abdel-Aziz, A. A. Mubarak, M. A. El-Naggar, E. G. Abdel-Aziz

The performance of a rotating fixed bed reactor in recovering copper from industrial waste solutions by cementation is studied under various conditions. The rotating fixed bed is made of stacked woven steel screens to take advantage of two features of screens: the ability to present large area per unit volume and their ability to promote high turbulence. Variables studied are initial CuSO4 concentration, bed rotation speed, mesh number of the screens and bed thickness. The presence of baffles was found to increase the rate of cementation. The data were correlated by a dimensionless mass transfer correlation suitable for the design and operation of large scale cementation reactors.

By G Lumley

PlannersÆ optimism (or maybe commercial necessity) means that most mine plans use equipment rates that are rarely achieved (Lumley and Beckman, 2009). This lack of understanding of what equipment actually moves is causing erroneous equipment forecasts, leading to incorrect mine development plans and economic evaluations. Compounding this problem is a downward trend in actual equipment performance in some areas. Consequently, the presentation of realistic mine plans that are actually achieved in practice is not a common occurrence. However, rational, fact-based mine planning is available to those who want it. Hundreds of millions of cycles of data from open cut mining equipment has been collected from mines around the world since 1992. This unique and highly valuable databank is growing at an exponential rate and is being used by a number of our big miners to support rational and fact-based decision-making. However, neither the use nor the appreciation of the value of this data is universal. There is a challenge to everyone in the mining industry - how do you access value from it? The databank was drilled into and the results analysed for, the Australasian Mining and Metallurgical Operating Practices (AMMOP) publication (Lumley, in press). For this paper the analysis has been extended to include interpretation of trends for draglines, shovels, excavators and trucks. It investigates trends between coal and non-coal mines and across geographic areas. It is known that mining equipment performance in most sections of the industry is falling. This paper attempts to quantify the fall and provide explanations. The trends are analysed to extract the reasons behind the changes and most importantly, what can be done about it.CITATION:Lumley, G, 2012. Understanding trends in performance of open cut mining equipment, in Proceedings Project Evaluation 2012 , pp 203-224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

Technically competent, skilled and efficient people are often promoted into management and leadership positions, climbing through the ranks to senior positions without training or direction in soft skilling. These soft skills are what really motivate teams to achieve business goals. This paper looks at the three key soft skill areas that compel teams to follow leaders, namely manners, mentoring and motivation. Our manners control our behaviour and attitudes and operate at a subconscious level. The manners that æmaketh the manager worth followingÆ are discussed with the express purpose of bringing these to our consciousness. When we recognise those behaviours that alienate or inspire we can consciously behave in ways to lead our teams towards our goals. Our attitude to mentoring and developing people around us speaks of our commitment to our people and our industry. Surprisingly, the more we give the more we get. Mentoring gives us an opportunity to leave a legacy, inspire commitment and build support within the mining community. How do we as managers provide mentoring within our teams? What are the mentoring behaviours that inspire learning and commitment to a managerÆs goals? When managers can identify an individualÆs unique mix of motivational drivers, they can understand how to motivate them. And motivated people are more likely to be retained and work towards the managerÆs goals. The soft skills used to understand and motivate within the three core motivation drivers (competence, expression and treatment) are presented. This paper is designed to share straightforward soft skills for managers who have tread the technical route.

Jan 1, 2006

By Joe Pease

"The demand for minerals and metals is increasing. Head grades of ore bodies are dropping. Remaining ores are becoming finer grained, more complex, and more logistically challenging. Mineral processing – in particular comminution – already consumes a huge amount of energy. But in 20 years’ time, it will require about six times as much energy as today to meet the world’s mineral demand.Unless we do something different.As minerals professionals, it is our job to find that “something different”. The world is relying on us. Of course, we must look for new breakthrough technologies and techniques. We must find them, and we will find them – most likely in surprising areas.But what if we also already know how to make 30-50% improvements to efficiency? Just by using existing technologies, by applying modern analytical techniques, by custom designing our plants, by applying manufacturing principles, by breaking down our management silos between disciplines.The thing is, industry professionals already know this. Yet – in spite of a lot of intelligent people trying very hard – we just can’t seem to make it happen.This discussion considers why, despite our best efforts, we don’t get the best out of what we already have. Why we are wasting energy and money. Once we understand why, we can set about unlocking that value and improving industry productivity and energy efficiency. We will discuss the role that professionals and volunteer professional organisations like CMP and CEEC can play in catalysing the changes."

Jan 1, 2015

By B. M. Larsen

Jan 1, 1948

By B. M. Larsen

Jan 1, 1948